Materials Science and Engineering Commons^™

Progress Of Pt-Based Catalysts In Proton-Exchange Membrane Fuel Cells: A Review, Long Huang, Hai-Chao Xu, Bi Jing, Qiu-Xia Li, Wei Yi, Shi-Gang Sun

Journal of Electrochemistry

Fuel cells are energy conversion devices that convert chemical energy directly into electricity. It has the advantages of high energy density, high utilization efficiency of fuel, clean and noiseless during working. Among all kinds of fuel cells, proton exchange membrane fuel cells (PEMFCs) are most popular since PEMFCs function at near ambient temperature, while their power densities are higher than those of other fuel cells. Currently, Pt-based nanomaterials are still the unreplaceable catalysts in commercialized PEMFCs. The lack of low-cost and high-performance cathode catalysts is still one of key factors that hampers the commercialization of PEMFCs. In this review, the …

Oxidative Efficiency Of Ozonation Coupled With Electrolysis For Treatment Of Acid Wastewater, Ze-You Hu, Feng-Yun Xiang, Ji-Qiang Mao, Ya-Lei Ding, Shao-Ping Tong

Journal of Electrochemistry

Establishment of an ozone-based advanced oxidation process (AOPs-O₃) for effective treatment of acid wastewater is an important and difficult task. The process of ozonation coupled with electrolysis (electrolysis-ozonation, E-O₃) has been reported to effectively degrade pollutants in neutral solution. We studied the efficiency of E-O₃ for degradation of acetic acid (HAc, an ozone inert chemical) in acid solution and found that E-O₃ had high oxidative efficiency at pH less than 3. For example, 52.2% of 100 mg·L^-1 HAc could be removed by E-O₃ in 120 min at pH 1.0, but only 2.2% …

Synthesis Of Lithium-Rich Manganese-Based Layered Cathode Materials And Study On Its Structural Evolution Of First Cycle Overcharge, Chen-Xu Luo, Chen-Guang Shi, Zhi-Yuan Yu, Ling Huang, Shi-Gang Sun

Journal of Electrochemistry

Lithium-rich manganese-based cathode materials have become one of promising cathode materials due to their low cost and large discharge specific capacity exceeding 250 mAh·g^-1. However, their problems such as low coulombic efficiency of first cycle and apparent voltage decay influence commercialization process. The high charging voltage will cause instability of structure and increase the hidden danger of the battery. Therefore, structural evolution of first cycle at higher voltage needs to be further studied. In this work, the precursor was synthesized by the co-precipitation method, and the lithium-rich manganese-based layered cathode materials were prepared by lithium-mixed and high-temperature sintering, …

Influence Of Pinholes On Water Vapor And Oxygen Permeation Of Packaging Foil And Films, Petri Johansson, Johanna Lahti, Jurkka Kuusipalo

Journal of Applied Packaging Research

Controlling of moisture and oxygen permeation through the packaging material is essential in most packaging applications. With multilayer structures of different barrier materials, there is possibility to create desired barrier properties to the package. The challenge is to plan appropriate barrier level, e.g. WVTR and OTR, theoretically to the package before producing the package. Furthermore, in specific packages there is a need to control the permeation e.g. respiration in vegetable packages. Typically foils and polymer films have high barrier properties, therefore, permeation can be controlled by producing artificial pinholes in these kinds of packages.

Influence of artificial pinholes in aluminium …

Exciton Delocalization In A Dna-Templated Organic Semiconductor Dimer Assembly, Xiao Wang, Ruojie Sha, William B. Knowlton, Nadrian C. Seeman, James W. Canary, Bernard Yurke

Materials Science and Engineering Faculty Publications and Presentations

A chiral dimer of an organic semiconductor was assembled from octaniline (octamer of polyaniline) conjugated to DNA. Facile reconfiguration between the monomer and dimer of octaniline–DNA was achieved. The geometry of the dimer and the exciton coupling between octaniline molecules in the assembly was studied both experimentally and theoretically. The octaniline dimer was readily switched between different electronic states by protonic doping and exhibited a Davydov splitting comparable to those previously reported for DNA–dye systems employing dyes with strong transition dipoles. This approach provides a possible platform for studying the fundamental properties of organic semiconductors with DNA-templated assemblies, which serve …

Examining The Effect Of A Chitosan Biopolymer On Alkali-Activated Inorganic Material For Aqueous Pb(Ii) And Zn(Ii) Sorption, Sukanta K. Mondal, Chenglin Wu, Felix C. Nwadire, Ali A. Rownaghi, Aditya Kumar, Yusuf Adewuyi, Monday Uchenna Okoronkwo

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Biopolymers and alkali-activated materials have attracted a great deal of attention as adsorbents for the removal of heavy metal contaminants from aqueous solutions. Both materials are sustainable and feature unique properties, but biopolymers are relatively more expensive or difficult to prepare and exhibit low mechanical and surface properties, a narrow pH range, and thermal stability. In this study, hybrid adsorbents were prepared from both types of material, by alkali activation of low-cost fly ash precursors accompanied by incorporation of 0-2%mass chitosan biopolymer. Two types of alkaline activating solutions, NaOH and Na2SiO3, were employed to generate two sets of hybrid adsorbents …

Design And Fabrication Of A Low-Cost, Portable, Battery-Operated Surface Enhanced Raman Scattering (Sers) Optical Device, Blessing Adewumi

LSU Doctoral Dissertations

Raman Spectroscopy is a time-honored, non-invasive method for analyzing and identifying the molecular composition of materials. However, unenhanced Raman Spectroscopy has extremely low sensitivity which limits its sensing capability. SERS brings rough nano-metallic surfaces in contact with the material molecules to enormously enhance the Raman signals.

The sensitivity of SERS can be exploited in probe applications where the spectrometer needs to be brought near the specimen. For example, a long optical fiber coupled to a SERS device can be used to characterize and identify easy-to-reach cancerous tissues in organisms. Unfortunately, background signals in a long fiber can easily mask any …

Materials And Methodologies For Spectroscopic And Optical Analytical Applications In Cultural Heritage Conservation Science, Lyndsay Nichole Kissell

Dissertations and Theses

The field of conservation science falls in the intersection of science and art. The work of conservation scientists may include any single subdiscipline of chemistry, though it is most commonly a highly interdisciplinary field taking skills from analytical, organic, and inorganic chemistry, as well as surface and materials science. The aims of conservation scientists are to answer questions about the production and aging of material cultural heritage. Knowing the materials used by an artist can lead to insight about the intentions of the object and knowing how those materials degrade will enable the use of preventative measures to ensure the …

Random Lasing In Nano-Crystalline Zinc-Oxide Films, Benito Reynaldo Resendiz

Dissertations and Theses

In this thesis, we explore the preparation of random lasers (RLs) using solution-deposited, randomly packed nano-particle films of zinc oxide (ZnO) impregnated with silicon dioxide (SiO₂) nanospheres. RLs have their scatterers randomly oriented, while their lasing comes from light propagating along closed paths through the scattering environment. It is shown here that random lasing is readily observed in films made of submicron sized ZnO particles. Adding transparent SiO₂ nanospheres to the films, we show there is an effective improvement of the lasing that is observable in all of the samples spectra. Specifically, we found that the lasing …

Quasi-Static Multifunctional Characterization Of 3d-Printed Carbon Fiber Composites For Compressive-Electrical Properties, Ritesh Ghimire, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Multifunctional carbon fiber composites provide promising results such as high strength-to-weight ratio, thermal and electrical conductivity, high-intensity radiated field, etc. for aerospace applications. Tailoring the electrical and structural properties of 3D-printed composites is the critical step for multifunctional performance. This paper presents a novel method for evaluating the effects of the coating material system on the continuous carbon fiber strand on the multifunctional properties of 3D-printed composites and the material's microstructure. A new method was proposed for the quasi-static characterization of the Compressive-Electrical properties on the additively manufactured continuous carbon fiber solid laminate composites. In this paper, compressive and electrical …

Uncertainties Induced By Processing Parameter Variation In Selective Laser Melting Of Ti6al4v Revealed By In-Situ X-Ray Imaging, Zachary A. Young, Meelap M. Coday, Qilin Guo, Minglei Qu, S. Mohammad H. Hojjatzadeh, Luis I. Escano, Kamel Fezzaa, Tao Sun, Lianyi Chen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Selective laser melting (SLM) additive manufacturing (AM) exhibits uncertainties, where variations in build quality are present despite utilizing the same optimized processing parameters. In this work, we identify the sources of uncertainty in SLM process by in-situ characterization of SLM dynamics induced by small variations in processing parameters. We show that variations in the laser beam size, laser power, laser scan speed, and powder layer thickness result in significant variations in the depression zone, melt pool, and spatter behavior. On average, a small deviation of only ~5% from the optimized/reference laser processing parameter resulted in a ~10% or greater change …

A Deep Learning Approach To Design And Discover Sustainable Cementitious Binders: Strategies To Learn From Small Databases And Develop Closed-Form Analytical Models, Taihao Han, Sai Akshay Ponduru, Rachel Cook, Jie Huang, Gaurav Sant, Aditya Kumar

Electrical and Computer Engineering Faculty Research & Creative Works

To reduce the energy-intensity and carbon footprint of Portland cement (PC), the prevailing practice embraced by concrete technologists is to partially replace the PC in concrete with supplementary cementitious materials [SCMs: geological materials (e.g., limestone); industrial by-products (e.g., fly ash); and processed materials (e.g., calcined clay)]. Chemistry and content of the SCM profoundly affect PC hydration kinetics; which, in turn, dictates the evolutions of microstructure and properties of the [PC + SCM] binder. Owing to the substantial diversity in SCMs' compositions–plus the massive combinatorial spaces, and the highly nonlinear and mutually-interacting processes that arise from SCM-PC interactions–state-of-the-art computational models are …

A Deep Learning Approach To Design And Discover Sustainable Cementitious Binders: Strategies To Learn From Small Databases And Develop Closed-Form Analytical Models, Taihao Han, Sai Akshay Ponduru, Rachel Cook, Jie Huang, Gaurav Sant, Aditya Kumar

Electrical and Computer Engineering Faculty Research & Creative Works

To reduce the energy-intensity and carbon footprint of Portland cement (PC), the prevailing practice embraced by concrete technologists is to partially replace the PC in concrete with supplementary cementitious materials [SCMs: geological materials (e.g., limestone); industrial by-products (e.g., fly ash); and processed materials (e.g., calcined clay)]. Chemistry and content of the SCM profoundly affect PC hydration kinetics; which, in turn, dictates the evolutions of microstructure and properties of the [PC + SCM] binder. Owing to the substantial diversity in SCMs' compositions-plus the massive combinatorial spaces, and the highly nonlinear and mutually-interacting processes that arise from SCM-PC interactions-state-of-the-art computational models are …

Centrifugal Assembly Of Bijel Ropes Via Helical Microfluidics, Shankar P. Kharal

Theses and Dissertations

Bicontinuous interfacially jammed emulsion gels (bijels) are soft materials that retain a liquid bicontinuous network stabilized by an interfacially jammed layer of nanoparticles. In this thesis, we investigated a microfluidic twisting method to fabricate micro-ropes of nano-structured bijel fibers. This method shows how weak microfibers with tensile strengths of a few kPa can be reinforced by 4 orders of magnitude by means of microfluidic twisting. Microfluidic twisting allows to produce continuous bijel fiber ropes of controllable architecture. Modelling the fluid flow field reveals the rope geometry dependence on a subtle force balance composed of rotational and translational shear stresses. However, …

Active Packaging Film Based On Poly Lactide-Poly (Butylene Adipate-Co-Terephthalate) Blends Incorporated With Tannic Acid And Gallic Acid For The Prolonged Shelf Life Of Cherry Tomato, Shubham Sharma, Kalpani Perera, Dileswar Pradhan, Brendan Duffy, Amit Jaiswal, Swarna Jaiswal

Articles

The antimicrobial property is the key feature of active packaging. Biological macromolecules such as tannic and gallic acids are naturally found in plants such as tea, fruits, berries, and grapes. The incorporation of tannic acid (TA) and gallic acid (GA) in the biodegradable polymer blend Poly Lactide-Poly (Butylene Adipate-Co-Terephthalate) (PLA-PBAT) was used in this study to assess the potential of active packaging. TA and GA (10 wt%) composite films showed a 65%–66% increase in the UV barrier property. The tensile strength value increased after the incorporation of TA and GA (10 wt%), respectively. Overall, 1.67 and 2.2 log reductions in …

Implementation Of Multiscale Mechanisms In Finite Element Analysis Of Active Composite Structures, Amany Micheal, Yehia Bahei-El-Din

Centre for Advanced Materials

Interrogation of composite structures for inherent damage is investigated by implementing a three-tier analysis scheme. The analysis starts at the structure level where a general-purpose Finite Element code ABAQUS is employed to obtain the stress field in the second level of analysis which is the composite laminate. A special material routine is prepared to propagate the local fields to the individual plies and hence to the third level of analysis which is the microstructure modeling of the composite. Through the third level of analysis, interface damage between fiber and matrix is checked implementing a certain failure criteria. The interaction between …

Modeling Isothermal Reduction Of Iron Ore Pellet Using Finite Element Analysis Method: Experiments & Validation, Amogh Meshram, Joe Govro, Ronald J. O'Malley, Seetharaman Sridhar, Yuri Korobeinikov

PSMRC Faculty Research

Iron ore pellet reduction experiments were performed with pure hydrogen (H₂) and mixtures with carbon monoxide (CO) at different ratios. For direct reduction processes that switch dynamically between reformed natural gas and hydrogen as the reductant, it is important to understand the effects of the transition on the oxide reduction kinetics to optimize the residence time of iron ore pellets in a shaft reactor. Hence, the reduction rates were studied by varying experimental parameters such as the temperature (800, 850 & 900 degrees C), reactant gas flow rate (100, 150 & 200 cm³/min), pellet size and …

Monitoring Of State Transitions In Extreme Environment Application Materials Using Fiber Bragg Grating Sensors, Sabuj Khadka

Electronic Theses and Dissertations

By embedding both a single fiber Bragg grating (FBG) sensor and a thermocouple (TC) during the manufacturing for extreme environment applications of certain classes of materials such as metals and polymers, a novel in-situ approach was developed to precisely monitor their entire manufacturing processes. This novel monitoring technique was able to identify many characteristic points during the curing of room and high-temperature epoxies and the solidification processes of metal alloys composed of tin and bismuth which were selected in this research purely for verification purposes. Some of the characteristic points identified for the epoxies were: (i) the gel point, (ii) …

Carbon Nanotube Coated Fibrous Tubes For Highly Stretchable Strain Sensors Having High Linearity, Chenchen Li, Bangze Zhou, Yanfen Zhou, Jianwei Ma, Fenglei Zhou, Shaojuan Chen, Stephen Jerrams, Liang Jiang

Articles

Strain sensors are currently limited by an inability to operate over large deformations or to exhibit linear responses to strain. Producing strain sensors meeting these criteria remains a particularly difficult challenge. In this work, the fabrication of a highly flexible strain sensor based on electrospun thermoplastic polyurethane (TPU) fibrous tubes comprising wavy and oriented fibers coated with carboxylated multiwall carbon nanotubes (CNTs) is described. By combining spraying and ultrasonic-assisted deposition, the number of CNTs deposited on the electrospun TPU fibrous tube could reach 12 wt%, which can potentially lead to the formation of an excellent conductive network with high conductivity …

Improving The Performance And Durability Of Metal Contacts In Crystalline Silicon Solar Cells Using Advanced Characterization, Nafis Iqbal

Electronic Theses and Dissertations, 2020-2023

Solar energy is one of the fastest growing forms of energy generation due to its low cost, lack of emissions, minimal maintenance, and excellent durability. However, like any other technology, it is also not free from defects and degradation, which limit its performance in the real world. Most of the degradation is related to metal contacts, which also happens to be one of the most expensive items in manufacturing, comprising almost half of the cost of converting a silicon wafer into a photovoltaic (PV) cell. Therefore, studying contact degradation to make them reliable and free of defects is the key …

Synchronous Raman Microspectroscopy And Laser Beam Induced Current Measurements As A Metrology Tool For Solar Cells And Optoelectronic Devices, Jeya Prakash Ganesan

Electronic Theses and Dissertations, 2020-2023

This works developed synchronous Raman microspectroscopy with laser beam induced current (LBIC) measurements to generate insights into structure-property correlations in finished solar cell modules. Raman spectroscopy is a powerful, non-destructive technique to examine phase and composition of materials where a laser beam excites characteristic vibrational modes of chemical bonds in a material. Conducting Raman spectroscopy under a microscope (i.e., Raman microspectroscopy) with confocal capabilities allows the chemical constituents to be mapped with high spatial resolution in the x, y and z directions. Simultaneously, the excitation laser from Raman can also generate photocarriers in a semiconductor. In a solar cell, these …

Davydov-Split Aggregates Of Cyanine Dyes For Bovine Serum Albumin Detection, Yiping Ma

Electronic Theses and Dissertations, 2020-2023

The p-conjugated supramolecular aggregates have gained significant interest in recent years. The cyanine dye aggregates are particularly interesting due to their unique optical and excitonic properties, which cannot be found in individual molecules. Cyanine dyes can form different kinds of aggregates. H-aggregates are formed when dye molecules are packed in a face-to-face fashion, which gives rise to a blue-shift absorption band and strong emission quenching compared to the monomer. J-aggregates are composed of individual dye molecules in a head-to-tail stacking, which leads to a red-shift absorption band and a sharp intense emission band with a small Stoke shift compared with …

In Situ Transmission Electron Microscopy And Ab Initio Study Of The Electrochemomechanical Effect Of Lithium Penetration In Electrolytes For All-Solid-State Batteries, Megan Diaz

Electronic Theses and Dissertations, 2020-2023

Although the past twenty years have seen dramatic advancement in lithium-ion batteries (LIBs), these batteries are nearing their theoretical limit. Next generation energy storage technologies must therefore be developed to meet the ever-increasing demands for batteries with higher capacity, longer cycle lifetime, and increased safety. All-solid-state lithium battery (ASSLIB) technology is one of the promising candidates. It is equipped with a solid-state electrolyte (SSE) replacing the flammable organic liquid electrolyte used in current LIBs. The SSE's high modulus is expected to prevent lithium dendrites and enables the use of a lithium metal anode to contribute to its high capacity without …

Influence Of Growth Parameters On The Synthesis Of Mos2 Films, Victor Okonkwo

Honors Undergraduate Theses

Information processing is crucial in modern society, placing a great emphasis on the performance of optoelectronic devices to match ever increasing processing and memory needs. Within these devices, MoS₂ has demonstrated great potential as transistors due to its enhanced electrostatic control. As increased layer thickness of quality MoS₂ films have been shown to boost the performance of its transistors, growth parameters for the synthesis of ideally uniform and large area multilayered films via chemical vapor deposition were investigated. By increasing the flow pressure in the system and the growth time, increasing levels of thickness and nucleation density was …

Engineering The Electrode Properties For Developing High Performance Supercapacitors, Kowsik Sambath Kumar

Electronic Theses and Dissertations, 2020-2023

Rising global warming concern demands the need for a rapid transition to renewable energy sources. The intermittent nature of these sources emphasizes the requirement of developing highly efficient electrochemical energy storage devices like supercapacitors and batteries. Supercapacitors are at the forefront of powering various devices spanning from electric cars to aircraft. Here, we have engineered the electrode material properties for developing supercapacitors with high capacitance, energy density and cycle life. Among the electrode materials, we have focused on improving the energy storage performance of 2D materials like graphene oxide (GO) and tungsten disulfide (WS2), in addition to metal oxides such …

Processing-Microstructure-Property Correlation For 316l Stainless Steel Manufactured By Laser Powder Bed Fusion, Nathalia Diaz Vallejo

Electronic Theses and Dissertations, 2020-2023

The microstructural development of 316L stainless steel (316L SS) was investigated over a wide range of systematically varied laser powder bed fusion (LPBF) parameters, such as laser power, laser scan speed, hatch distance, and volumetric energy density. The use of volumetric energy density between 46 and 127 J/mm3 produced samples with relative density above 99.8% demonstrating that even in the optimized range of processing parameters the pores are unavoidable. Shifting from this range through a variation of laser scan speed produced two types of flaws, lack of fusion (LoF) and keyhole (KH) porosity leading to a decrease in the relative …

Effect Of The Extended Rigid Flapping Trailing Edge Fringe On An S833 Airfoil, Hongtao Yu, Zifeng Yang

Mechanical and Materials Engineering Faculty Publications

A 2D numerical simulation was conducted to investigate the effect of an extended rigid trailing edge fringe with a flapping motion on the S833 airfoil and its wake flow field, as an analogy of an owl’s wing. This study aims to characterize the influence of the extended flapping fringe on the aerodynamic performance and the wake flow characteristics downstream of the airfoil. The length (Le) and flapping frequencies (fe) of the fringe are the key parameters that dominate the impact on the airfoil and the flow field, given that the oscillation angular amplitude is fixed at 5◦. The simulation results …

From Field To Failure: Detecting And Understanding Reliability Defects In Crystalline Silicon Photovoltaics, Dylan Colvin

Electronic Theses and Dissertations, 2020-2023

Severe pollution levels and the growing influence of climate change have shown that dirty energy sources need renewable and sustainable replacements. The field of photovoltaics (PV) has grown substantially over the years from a niche space solar market to a commodity in large part due to improvements in reliability. Reliability of all materials in a PV module must be considered. The industry has seen an explosion of innovation in cell interconnection technologies with significant market penetration in the past several years. These emerging, less mature technologies require more reliability information to guide improvements. Degradation studies of long-term outdoor exposure and …

Effects Of Vacancies And Electron Temperature On The Electron Phonon Coupling In Cubic Silicon Carbide And Their Connection To The Inelastic Thermal Spike, Salah Al-Smairat

Doctoral Dissertations

“The electron-phonon interaction is an important interaction in many solids as it influences transport phenomena and related quantities such as the electrical and thermal conductivities, especially in nuclear and space applications. The importance of the electron-phonon interaction in primary damage production in 3C-SiC is the subject of this research.

The electron-phonon coupling factor was calculated using a hybrid Density Functional Perturbation Theory - Classical Electron Gas model. The coupling factor was calculated as a function of electron temperature in pristine and defective 3C-SiC, and relaxed defective cells. The electron-phonon coupling is found to depend strongly on the electronic temperature and …

Corrosion Protection Mechanisms Of Trivalent Chromium Based Passivations On Γ-Znni Coated Al6061-T6 Alloy, Kevin Foster

Doctoral Dissertations

“The role of cobalt in trivalent chromium passivations (TCPs) to improve corrosion resistance of γ-ZnNi coated steel and aluminum is based on its effect on hexavalent chromium content in the passive layer. Investigations of both a cobalt-containing and cobalt-free TCP on SAE 1008 steel indicated that both passivations protect well for up to 1000 hours in neutral salt spray exposure (SSE). A repetition on Al 6061-T6 alloy indicated that TCP performed much better than cobalt-free TCP implicating the underlying substrate. Optical and electron micrographs indicated physical changes such as crack thickness, crack density, passivation porosity, and passivation thickness existed between …