Electrical and Electronics Commons^™

Microcomputer Control Of An Ac Induction Motor Using A Pwm Computational Intensive Method, Luther William Schnug

Theses

A three-phase microcomputer based AC Inverter has been developed using a computational intensive PWM algorithm that generates the output bridge switching patterns in real time. This approach utilizes the on-board capabilities of an advanced microcontroller, (a 16-bit 8097 from Intel), to eliminate most of the external hardware, and demands on memory size, required in other designs. This algorithm implements in software the Triangular Modulation Method of PWM generation, and utilizes a trapezoidal approximation to the sinusoidal reference waveform. Brassboard tests have shown that this approximation produces 5th and 7th harmonics that degraded performance, at low speeds. An enhanced algorithm, utilizing …

The Path Method In Power System State Estimation, Fareed A. R. Shirazi

Theses

A new method for Power System State Estimation (PSSE), the 'Path Method', is developed and studied. In this method the state (voltage magnitude and angle) of one node is calculated at a time, using only the local measurements. This procedure is repeated to calculate the state of all nodes in the system, following a predefined path to determine the next node whose state is to be calculated. In the process, more measurements are used whenever available and possible. Results obtained for this method are comparable and close to those of the Line-Flow Only (LFO) method. An advantage of the Path …

Computation Of Frequency Characteristics Of Lumped-Element 3 Db Branch Line Directional Couplers, H. R. Mgombelo

Tanzania Journal of Engineering and Technology (TJET)

An analysis of the 3 dB lumped-element branchline directional coupler constructed using L-C and T networks is given. Matrices of lumped element capacitances and inductances in the form of low and high pass filters are equated to the matrices of the distributed element transmission lines at the centre frequency of operation, as a result of which design equations are derived. Using even and odd modes of excitation, frequency characteristics of the directional couplers are computed and compared to those of the coupler constructed using distributed element transmission lines.

Charge Transfer Inefficiency Of Buried-Channel Charged Coupled Device Registers For Low Temperature Operation Of Ptsi Infrared Image Sensors, Benjamin Benjamin Esposito

Theses

Buried channel charge coupled devices used as readout registers in PtSi Schottky-barrier detector infrared image sensors were investigated to characterize factors that influence charge transfer efficiency at low temperatures ranging from 38 to 80K. These factors included frequency of operation, background signal, gate voltage, signal level, gate length, and temperature. It was found that increased gate voltage and decreased gate length are most effective in reducing charge transfer efficiency. This was attributed to increased fringing fields between the potential wells involved in charge transfer. As temperature was decreased from 50K to 38K progressively larger trapping losses were observed due to …

Reflectance Of An Absorbing Substrate For Incident Light Of Arbitrary Polarization: Appearance Of A Secondary Maximum At Oblique Incidence, R. M.A. Azzam, A. M. El-Saba

Electrical Engineering Faculty Publications

The reflectance of an absorbing substrate Rθ(ɸ) is considered as a function of the angle of incidence ϕ and an incident polarization parameter θ, where cos²θ and sin²θ give the power fractions of incident radiation that are p-and s-polarized, respectively. Taking GaAs as an example, we find that at certain wavelengths (e.g., 0.248 and 0.620 µm), the R_θ vs ɸ curve becomes oscillatory in a narrow range of θ > 45° with an unexpected secondary maximum appearing at oblique incidence. The extrema of the function R_θ(ɸ) are determined numerically, and their angular …

Waveform Analysis And Application To A Model Of The Egg Waveform, Eu-Rune Chang

Theses

The purpose of thesis is to describe and investigate a model of electroglottogram waveform. At the beginning, we generate a set of sine waveform models to analyze by using Fourier transform theory. Then, according to the electroglottogram is conjectured to be related to the area contact between the vocal folds, we assume a simple model of vocal fold vibratory motion is used to estimate the vocal fold contact area as function of time. Therefore, we modified and developed the mathematic EGG waveform model by using personal computer program computation to become a set of realistic EGG waveform models, which are …

Optimal Cache Size In Microprocessor-Based Multiprogramming System, Charalambos Stephanou Christou

Theses

The Motorola 68020 microprocessor, its paged memory management unit MC68851 and cache memories are rigorously studied. The simulation model of this uniprocessor, multiprogramming system was constructed and tested to determine the optimal physical cache size.

The parameters varied in the model are the cache size, the degree of multitasking, the loop count and size, the cache algorithm and the time slice given to every task. A number of simulations have been conducted and the results are examined.

Arithmetic Pipline Scheduler, Chun-Ta Pan

Theses

A schedule is used to determine which stages of an arithmetic pipeline are active at any particular time. It can determine when another process can be introduced into the pipeline so no more than one set of data will use the same stage at the same time. The Arithmetic Pipeline Scheduler (APS) is a software tool used to analyze schedules for different operations and determine greedy schemes for introducing data into the pipeline. The user can use APS to process up to ten arithmetic equations. The user also can use APS to define different configurations of stages. Besides, APS can …

Kalman Filtering Applied To The Analysis Of Brainstem Auditory Evoked Potentials, Chong An Qian

Theses

The objective of this thesis is to detect the Brainstem Auditory Evoked Response (BAER) using lower numbers of averages than at present, by using an optimal smoothing method which is based on the Kalman Filter.

By using this method, the wave V latency of the BAER which is useful in testing for hearing loss can be detected with as low as 500 averages, while the traditional signal averaging method requires at least 2000 averages. Thus the time required for a hearing loss test can be reduced from one hour to approximately 20 minutes.

Also several other methods for detecting BAER …

Computer Analysis Of The Electrocardiogram Using Hardware Digital Signal Processing, Mohammad Ashfaque Shaikh

Theses

A system based on the microcomputer IBM PC-AT has been realized to acquire and filter the clinical electrocardiogram (ECG) data in real time. The system program further detects and analyzes the ECG signals for possible cardiac arrhythmias.

This research is based on work done by previous researchers and achieves significant goals towards achieving on-line arrhythmia detection using a microcomputer. The system uses the hardware and software package ASPI 320/PC from Atlanta Signal Processors Inc. This hardware configuration uses a special purpose instrumentation microprocessor ( TMS32010 from Texas Instruments) to coprocess the ECG signals. Coprocessing the signals with the ASPI 320/PC …

Learning System, Bhavesh T. Adani

Theses

Many rule-based learning systems have been implemented which generate and update rules/facts from illustrative examples provided by the user. But very few of them have succeeded in achieving the efficiency and accuracy of an ideal system.

The approach made here is to continuously update the hierarchical structure of rules/facts of a knowledge-base so that efficient and accurate solutions to any query can be achieved easily and immediately from the many possible solutions to the query. As the rule-based systems deal with a very large knowledge-base, it is sometimes necessary to apply a learning technique that finds optimum solutions efficiently.

The …

Analysis And Design Of A Surface Microengineered Silicon Humidity Sensor, Uei-Yanq Chen

Theses

This thesis details the design for a solid-state humidity sensor which utilizes state-of-the-art silicon technology. The sensor design utilizes a microengineered surface which includes a polysilicon airbridge structure as heater and sensor element in an integrated device.The operation of this device depends upon the small variation of thermal convection coefficient which effects the temperature of the heated element within the device. The temperature of the polysilicon bridge is monitored by means of a resistance bridge. In one design(sensor I) a single polysilicon airbridge is used for both the heater and resistance sensing element. Also a second inferior design (sensor II) …

Division-Of-Wave-Front Thin-Film Beam Splitter For Generating Binary Patterns Of Orthogonal Elliptical Polarization States, R. M.A. Azzam

Electrical Engineering Faculty Publications

A division-of-wave-front thin-film beam splitter is described that reflects monochromatic light at oblique incidence with orthogonal elliptical polarization states. It consists of a metallic substrate partially covered with a transparent thin film that inverts the ratio ρ of the complex p and s reflection coefficients at the principal angle of the metal. Any pattern of coated and uncoated areas of the substrate is imprinted upon the reflected wave front as a corresponding two-dimensional spatial binary polarization pattern. A specific design is given that uses a Au substrate at a wavelength of 632.8 nm. The effects of small errors in the …

Thin-Film Devices For Polarized Light- Introduction, R. M.A. Azzam, William H. Southwell

Electrical Engineering Faculty Publications

No abstract provided.

Clinical Base Station For Portable Patient Monitoring Equipment, Silin Kuang

Theses

In today's clinical environment, where it is not always desirable to have a computer terminal present, a microcontroller-based biomedical system with multi-purpose features is needed. The present work offers an approach for a clinical based desktop workstation that provides the physician with record files, general management of his patient group, and specific algorithms for patient or group analyses. The workstation has the capabilities to acquire a large number of data from a portable patient monitoring device, generate a hard copy graphic record, create a patient cardfile and an . office personnel loggin file, and check patient's appointment and emergency list. …

Istemcr : Integrated System For Truck Engine Monitoring Via Cellular Radio, Tse-Shan Pan

Theses

The study presented is aimed at the application of the Data Acquisition to The Truck Engine as the source of all the signals, with the mobile telephone Cellular Radio system.

A Word Based Data Compression Using Arithmetic Encoding, Christopher Dean Peckham

Theses

It is usually difficult to compress data from a statistically unknown source and yield a good compression ratio. Using the fact that words are the fundamental basis of the written language, a data compression scheme based on words should yield high compression ratios. Discussed here is a compression scheme that gathers words from the source stream and places them in a dictionary, or word list, to use later in the coding, thereby becoming adaptive to the words in a given file without prior knowledge of the source. When a word is in the word dictionary, it is encoded by its …

Data Extraction And Analysis In Glucose Monitor, Chang Qian

Theses

For the purpose of building a workstation to read and analyze data from hand-held, home use glucose monitor, a new high performance Digital Oscilloscope Peripheral (DOP) for PC is used to easy sample and store data, and it is described here. The new features of DOP are discussed and some application software packages for different purpose are described here in detail.

Since the sampled data from the hand-held, home use glucose monitor is irregular and in random form, the Least-Square Polynomial Modeling Method is used to produce a fit curve line, which best goes through most data points. Using the …

Implementation Of A Cross Coupled Phase Locked Loop System With Closed Loop Amplitude Control, Behzad Sadeghi

Theses

A system was designed, to demodulate an FM signal in presence of an interfering signal whose frequency was very close to the desired signal, this system was implemented and tested based on the theory of cross coupled phase locked loop systems, originaly proposed by (1).

This system included two phase locked loops for the purpose of demodulation, two low pass filters and two integrators, for the purpose of amplitude estimation. Two additional phase locked loops were designed to act as a 90° phase shifter. The following is the result of the theory, design procedure and some tabulated data for this …

Extrema Of The Magnitude And The Phase Of A Complex Function Of A Real Variable: Application To Attenuated Internal Reflection, R. M.A. Azzam

Electrical Engineering Faculty Publications

Given a complex function F(ω) = |F(ω)|exp[jΔ(ω)] of a real argument ω, the extrema of its magnitude |F(ω)| and its phase Δ(ω), as functions of ω, are determined simultaneously by finding the roots of one common equation, Im[G(ω)] = 0, where G= (F′/F)² and F′ = ∂F/∂ω. The extrema of |F| and Δ are associated with Re G < 0 and Re G > 0, respectively. This easy-to-prove theorem has a wide range of applications in physical optics. We consider attenuated internal reflection (AIR) as …

Assessment Of Autonomic Regulation Of Heart Rate Variability, Shaw-Jyh Shin

Dissertations

Complex demodulation, accompanied by the techniques of interpolation, detrending and zero-phase-shift lowpass filtering were used to examine the effect of both divisions of the autonomic nervous system (sympathetic and parasympathetic) on heart rate by analyzing the heart rate variability signal from dogs under two different classical conditionings: CS+ and CS-, which cause different dynamic pattern changes in the autonomic nervous system to regulate the heart rate.

Unlike power spectral analysis, complex demodulation gives results in the time domain and shows the variation of amplitude and phase over time at a given frequency. The variation of phase indicates the frequency deviation …

Cmos Sram Design For Initializing Programmable Logic Devices, Ravi K. Vaidyanathan

Theses

This thesis presents the design of CMOS Static Random Access Memory (SRAM) which is imbedded within a high performance Programmable Logic Device (PLD). The SRAM and its control circuitry are used to initialize (or personalize) the NJIT PLD chip. The design is defined in 3-levels of functional hierarchy consistent with the physical and electronic design automation utilized for this design. The imbedded SRAM supports the PLD application circuit which includes 8 small Array and one large Control Programmable Logic Arrays.

The SRAM is structured as 64 X 138 bit array with serial read and write inputs. It is designed emphasizing …

Analysis Of Spread Spectrum System Using Direct Sequence Technique In Jamming Environment, Kandarp A. Vyas

Theses

A spread spectrum system is a means of transmitting data over a channel In addition it offers a wide variety of features like data security and signal hiding This work studies in detail a spread spectrum system using direct sequence binary phase shift keying. The Sliding Correlator and Sequential Detector techniques have been used to achieve synchronization. A brief study of pseudorandom noise has been presented. System was simulated on UNIX using 'c'. A modified version, suitable for software implementation, of Sliding Correlator and Sequential Detector was, used. Results generated using tins model are presented here.

Attenuation Properties Of An Lp 11 Mode In A W-Type Fiber Operating Below Cutoff, Chih-Chiang Wang

Theses

Rigorous formulation of a W-type fiber for its dispersion properties is presented. An LP mode has been studies extensively with respect to its attenuation properties when the frequency of operation is kept below cut-off. Due to rigorous dispersion equation numerical difficulties encountered in the computations, an approximate dispersion equation corresponding to weakly guided modes is solved. Numerical results corresponding to attenuation and propagation characteristics of the W-type fiber for radii and refractive index variations are presented. A computational subroutine for radial functions (Bessel, etc ) for complex argument has been used and proved to be useful in the legion of …

Research, Development, And Evaluation Of A Solid State Transformer, Robert Michael Joseph Wozniak

Theses

The analysis and design of a solid state step down transformer is presented as part of a research study which reviews novel approaches to the development of high frequency power magnetic apparatuses and applies available theory to produce a solid state counter part. The resulting circuit exhibits the potential for efficiency as high as 85%, low output ripple, regulation that is comparable with other modes of power conversion and the ability to provide localized on-board power.

Schema Based Wiring Tool : A Computer Network And Cad Design System, Jia Jing Zhang

Theses

For the purpose of building a SBC-8052-Basic micro-controller based instrument system, a new SCHEMA II Computer Aided Design system for IBM-PC is used to enhance circuits design routine, and it is described here. The new features of this CAD are discussed, and the design example of a new version of the SBC-8052-Basic micro-controller is given here in detail.

Since the wiring board system is adopted as tool of the laboratory development and controlled by the QL microcomputer, and since SCHEMA II CAD, on the other hand, is used on the IBM-PC-AT, communication between the two microcomputers is accomplished, and the …

On-Line Blood Glucose Control System, Huan Zheng

Theses

A method has been developed that can monitor and control the meal initiation of rats. The goal of studying meal initiation is to find a mechanism of control of the diet, based upon the assumption that the body weight is closely related to feeding behavior. If the feeding behavior can be controlled, then the body weight can be controlled. The experimental system has two major functions: (1) Continuous measurement and recording of the blood glucose concentration and meal pattern of rats. (2) Automatic or manual infusing of glucose or other substances to the rats intravenously.

For blood glucose concentration and …

C/Ku Band Satellite Television Reception System, Costas A. Economides

Theses

The purpose of this thesis is to examine and investigate the design of a satellite reception system able to receive most C and Ku band North American geostationary satellites' TV transmissions. The performance criterion used for the system design is based on a required demodulated video signal-to-noise ratio maintained for a specified percentage of time in conjunction with overall cost considerations.

Furthermore, a computer program written in FORTRAN 77 is developed, which among other functions lists the notified, operational, geostationary satellites in sight with their corresponding look angles, from any given location on the earth.

A Silicon Photodiode Array For Soft X-Ray Sensing, Chih-Te Hu

Theses

An array of 30 x 30 sensing cells including logic within each cell and a self-scan address circuit are described. A unique scintillation technique is used to increase the threshold sensitivity 60dB for X-ray photon sensing beyond that obtainable with conventional photodiode sensors. Simulations for the sensing cell and some additional logic elements are based on SPICE version 2G5 and HILO 3. Worst case analysis includes variations in threshold voltage V_TP and V_TN for the CMOS circuit components. The final CMOS chip dimension using MOSIS 1.2 micron rules is 10mm x 10mm base on the 80 …

Investigation Of Different Cmos Dram Sense Amplifier Configurations In Vlsi, Bihju Chiu

Theses

Sense amplifiers are particularly difficult circuits to design. In this work, only CMOS sense amplifiers are considered. There are typically two configurations of CMOS sense amplifiers: the cross-connected flip flop configuration and the current-mirror configuration. They are widely used nowadays with various modifications. These improved configurations are simulated and optimized with SPICE package, and their relative performances are also compared in this thesis.