Electrical and Electronics Commons^™

Motion Estimation And Video Coding, Xiaochun Xia

Dissertations

Over the last ten years. research on the analysis of visual motion has come to play a key role in the fields of data compression for visual communication as well as computer vision. Enormous efforts have been made on the design of various motion estimation algorithms.

One of the fundamental tasks in motion estimation is the accurate measurement of 2-D dense motion fields. For this purpose. we devise and present in this dissertation a multiattribute feedback computational framework. In this framework for each pixel in an image. instead of a single image intensity. multiple image attributes are computed as conservation …

Scheduling And Discrete Event Control Of Flexible Manufacturing Systems Based On Petri Nets, Huanxin Henry Xiong

Dissertations

A flexible manufacturing system (FMS) is a computerized production system that can simultaneously manufacture multiple types of products using various resources such as robots and multi-purpose machines. The central problems associated with design of flexible manufacturing systems are related to process planning, scheduling, coordination control, and monitoring. Many methods exist for scheduling and control of flexible manufacturing systems, although very few methods have addressed the complexity of whole FMS operations. This thesis presents a Petri net based method for deadlock-free scheduling and discrete event control of flexible manufacturing systems. A significant advantage of Petri net based methods is their powerful …

Residual Stress Analysis Of Sputtered Tantalum Silicide Thin Film, Young Joo Song

Theses

The influence of different argon pressures on the residual stress, microstructure, and resisitivity of sputtered tantalum silicide thin films has been investigated. TaSi₂ films were deposited onto Si wafers by dc magnetron sputtering. The deposition temperature was assumed to be 300°C. The thickness was about 0.5 μm. The residual stresses in the films deposited at different argon pressures were determined by curvature measurement method. The compressive intrinsic stress of 1033.4MPa was measured at P_Ar = 0.5 mTorr. The intrinsic stress in the films seemed to change from compression to tension as P_Ar increased above 8mTorr. A maximum …

Real-Time Implementation Of An Adaptive Control System For A 3-Zone Rapid Thermal Processing Station, David Hur

Theses

In this thesis, the implementation details of a real time adaptive control system for a TI 3-zone RTP station, as well as the simulation and the experimental results are presented. Extensive simulation of the system is performed in order to ensure proper operation of the system. The experimental results are used to verify proper operation of the closed loop control system. Initial experiments were conducted using two thermocouples. Further experiments were conducted using one thermocouple for the purpose of testing the performance of the system using Extended Kalman Filter as the state estimator.

The implementation of the control system is …

Adaptive Color Correlation Of Knots In Wood Images And Weighted-Value Product Selection Methods In A Machine Vision System, John Robert Goulding

Dissertations and Theses

The biggest obstacle to robust color image processing of wood is in developing a color model that represents all possible defect colors. When the color model is too general or too specific, defect recognition fails because too many or too few non-defect pixels match the model, respectively. Because a color image of wood contains far more clear and clear-grain colored pixels than grain-knot and knot colored pixels, it is beneficial to first statistically identify and remove the clear and clear-grain colors and to use the accumulated data to simultaneously enhance and normalize the remaining grainknot and knot colored pixels. This …

Study Of Stress In Microelectronic Materials By Photoelasticity, Hancheng Liang

Dissertations

The study of stress is playing an important role in microelectronic technology. In comparison with other techniques, the photoelasticity technique has the advantages of having high spatial resolution and high sensitivity. It can be used in qualitative observation in real-time and quantitative determination of stress distribution in the microelectronic materials and devices.

This dissertation presents a systematic study of photoelastic stress analysis in microelectronic materials and devices, ranged from theoretical study to practical system setup, from measurement methods to their applications. At first, based on the detailed survey on the piezo-optic properties of the crystals used in microelectronics, we apply …

Infrared Quarter-Wave Reflection Retarders Designed With High-Spatial-Frequency Dielectric Surface-Relief Gratings On A Gold Substrate At Oblique Incidence, Jian Liu, Rasheed M.A. Azzam

Electrical Engineering Faculty Publications

One- and two-dimensional high-spatial-frequency dielectric surface-relief gratings on a Au substrate are used to design a high-reflectance quarter-wave retarder at 70° angle of incidence and 10.6-μm light wavelength. The equivalent homogeneous anisotropic layer model is used. It is shown that equal and high reflectances (>98.5%) for the p and the spolarizations and quarter-wave retardation can be achieved with two-dimensional ZnS surface-relief gratings. Sensitivities to changes of incidence angle, light wavelength, grating filling factor, and grating layer thickness are considered.

Determination Of The Refractive Index And Thickness Of Transparent Pellicles By Use Of The Polarization-Independent Absentee-Layer Condition, Y. Cui, R. M.A. Azzam

Electrical Engineering Faculty Publications

The refractive index and the thickness of a transparent pellicle are determined when the pellicle is placed between two vertical crossed polarizers and rotated in the horizontal plane. The transmission axes of the polarizers are neither parallel nor perpendicular to the plane of incidence. The light transmitted through the crossed polarizers reaches a minimum when the pellicle satisfies the absentee-layer condition. The refractive index and the film thickness are obtained from the pellicle orientation angles under such a condition.

Extended Permutation Filters And Their Application To Edge Enhancement, Russell C. Hardie, Kenneth E. Barner

Electrical and Computer Engineering Faculty Publications

Extended permutation (EP) filters are defined and analyzed. In particular, we focus on extended permutation rank selection (EPRS) filters. These filters are constrained to output an order statistic from an extended observation vector. This extended vector includes N observation samples and K statistics that are functions of the observation samples. The rank permutations from selected samples in this extended observation vector are used as the basis for selecting an order statistic output. We show that by including the sample mean in the extended observation vector, the filters exhibit excellent edge enhancement properties. We also show that several previously defined classes …

Characterization And Fabrication Of A (6h)-Sic As A Piezoresistive Pressure Sensor For High Temperature Applications, Robert Sylvester Okojie

Dissertations

A prototype monolithic 6H-SiC pressure sensor operational up to 350°C, with potential to operate up to 600°C, was batch fabricated and tested. At temperatures higher than 450°C, silicon diaphragms creep under minimal load. To operate beyond 450°C, therefore, the use of 6H-SiC was proposed. However, three key technological issues - fabrication, high temperature metallization, and gage factor characterization - had to be resolved. Since conventional fabrication technology is not applicable to SiC due to its near inert chemistry, photoconductive selectivity techniques to etch the piezoresistors were developed. Techniques to wet etch the cavities in a dark current mode were developed, …

Explicit Congestion Control Algorithms For Available Bit Rate Services In Asynchronous Transfer Mode Networks, Ambalavanar Arulambalam

Dissertations

Congestion control of available bit rate (ABR) services in asynchronous transfer mode (ATM) networks has been the recent focus of the ATM Forum. The focus of this dissertation is to study the impact of queueing disciplines on ABR service congestion control, and to develop an explicit rate control algorithm.

Two queueing disciplines, namely, First-In-First-Out (FIFO) and per-VC (virtual connection) queueing, are examined. Performance in terms of fairness, throughput, cell loss rate, buffer size and network utilization are benchmarked via extensive simulations. Implementation complexity analysis and trade-offs associated with each queueing implementation are addressed. Contrary to the common belief, our investigation …

Design, Process And Performance Simulation Of A 360x360-Element Very High Frame Rate Burst-Image Sensor, Guang Yang

Dissertations

A process was developed for fabrication of 360x360-element Very High Frame Rate (VHFR) burst-image sensor on the bases of one-dimensional (1-D) and two-dimensional (2-D) device and process simulations using SUPREM III, SUPREM IV, PISCES IIB and ISE-TCAD software, and the process data provided by the David Sarnoff Research Center. This process includes SiO₂-Si₃N₄ gate dielectric, four-levels of polysilicon, three-levels of metal, eight implants, and requires twenty-one mask levels. The imagers with a 2-cmx2-cm chip size were fabricated at the David Sarnoff Research Center. The VHFR burst-image sensor is capable of capturing images at frame rates …

A Full Wave Method For Rough Surface Scattering Using Fictitious Current Distributions, Anthony A. Triolo

Dissertations

Rough surface scattering is a current topic of interest in many diverse fields. But, despite its importance, the two most widely used solution methods, the Kirchhoff and first order perturbation methods, are valid only for a restricted range of surface types. There is a large range of surface statistics for which neither of these theories is valid. There are purely numerical solutions to the problem, i.e., the integral equation technique and FDTD method, but these methods require a prohibitively large amount of computer time and storage space for use in practical applications. A full wave method has been introduced by …

A Digital Signal Processor Based Optical Position Sensor And Its Application To Flexible Beam Control, Thomas J. Spirock

Theses

A Digital Signal Processor (DSP) based optical position sensor was developed. The sensor system consists of the following components: 1) analog electronics, 2) the DSP based synchronous demodulation software, 3) PC based interface software which samples and saves the data, and 4) PC based control codes for a flexible beam. experiment.

The ability of the system to determine the distance from the optical sensor to the power modulated light source was assessed by the following tests: 1) a stationary drift test to evaluate the system's noise, 2) a short-range test to determine the resolution of the optical sensor over a …

The Study Of Sige-Channel Heterojunction Mos Device, Yunchen Qiu

Theses

The advances in the growth of pseudomorphic silicon-germanium epitaxial layer combined with the strong need for high-speed CMOS VLSI circuit have led to increased interest in silicon-based heterojunction MOSFET's transistors. The high-performance heterostructure SiGe MOSFET exhibits higher channel mobility than its bulk Si counterpart. The most critical and challenging process for fabricating a SiGe MOSFET device is that for making a gate oxide with sufficient quality for useful conductivity modulation. PECVD methods was employed to deposit the gate oxide and C-V method was used to investigate the electrical characteristics of the film. For PECVD gate oxide, a film refractive index …

Remote Measurement Calibration In Power System, Xiaofeng Li

Theses

Power system reliability and economy of operation require accurate measurements of current, voltage, real and reactive powers. These measurements are transmitted to a control center of a power system for monitoring, display, and use in power system real-time analysis. The number of measurements is in thousands. Routinely field technicians must calibrate transducers and/or determine other sources of metering errors. Due to the large number of measurements and the time required to check each individual measurement, field calibration procedures are impractical, expensive, and not timely.

There has been a need for a more efficient approach to measurement calibration and identification of …

Simple Fast Vector Quantization Of The Line Spectral Frequencies, Jin Zhou

Theses

Speech coding has been of interest to communication specialists for years. A number of technologies for describing and transmitting the speech spectral envelope have been studied. Among them, the Vector Quantization (VQ) of Line Spectral Frequencies (LSF) is receiving more attention because of its good rate-distortion performance. Typically, about 30 bits are assigned to code 10-dimensional LSF vectors with a resulting spectral distortion of less than ldB. However, 30-bit full-search VQ is totally impractical in terms of both computational complexity and memory space. Various standard suboptimal, low-complexity VQ techniques have been used for coding the LSF's in the literature. The …

Low-Frequency Noise In 4h-Silicon Carbide Junction Field Effect Transistors, J. W. Palmour, M. E. Levinshtein, S. L. Rumyantsev, Grigory Simin

Faculty Publications

Low frequency noise in 4H‐silicon carbide junction field effect transistors (JFETs) has been investigated. JFETs with a buried p ⁺ n junction gate were manufactured by CREE Research Inc. Very low noise level has been observed in the JFETs. At 300 K the value of Hooge constant α is as small as α∼10⁻⁵ and the α value can be decreased by an appropriate annealing to α∼2×10⁻⁶. It has been shown that even these extremely low noise values are determined not by the volume noise sources but by the noise at the SiC–SiO₂ interface.

Genetic Algorithms Vs. Simulated Annealing: A Comparison Of Approaches For Solving The Circuit Partitioning Problem, Theodore W. Manikas, James T. Cain

Computer Science and Engineering Research

An important stage in circuit design is placement, where components are assigned to physical locations on a chip. A popular contemporary approach for placement is the use of simulated annealing. While this approach has been shown to produce good placement solutions, recent work in genetic algorithms has produced promising results. The purpose of this study is to determine which approach will result in better placement solutions.

A simplified model of the placement problem, circuit partitioning, was tested on three circuits with both a genetic algorithm and a simulated annealing algorithm. When compared with simulated annealing, the genetic algorithm was found …

Applications Of The Normal-Incidence Rotating-Sample Ellipsometer To High- And Low-Spatial-Frequency Gratings, Y. Cui, R. M.A. Azzam

Electrical Engineering Faculty Publications

The normal-incidence rotating-sample ellipsometer is an instrument that can be used to characterize grating surfaces from the measured ratio ρof complex reflection coefficients r_y/r_x of light polarized perpendicular and parallel to the grating groove direction. Experimental results at different wavelengths for different gratings with spatial frequencies from 150 to 5880 grooves/mm are presented. The groove depth of the 5880-grooves/mm gold-coated grating can be estimated from the measured ρ and rigorous grating theory.

Software Design Control Of An Autonomous Vehicle, Monish Sharma

Honors Capstone Projects and Theses

No abstract provided.

Frequency Response Enhancement Of A Flow Sensor Using Diamond Thin Films Synthesized By Plasma Cvd, John Curren Hagwood

Electrical & Computer Engineering Theses & Dissertations

Theoretical modeling conducted previously in our Microelectronics Laboratory has shown that a layer of diamond film inserted between a metal film and a substrate will enhance the frequency response of a conventional thin film flow sensor. This thesis involved fabricating and testing a conventional thin film sensor of nickel on quartz (Ni/Q) and a diamond enhanced sensor (Ni/D/Q) for comparative frequency response analysis to validate the theory. Diamond films were grown onto quartz substrates using a microwave plasma enhanced chemical vapor deposition process. Conditions were established to synthesize continuous diamond films on quartz substrates. These films were characterized by scanning …

Electron Beam Emission From A Ferroelectric Cathode, Crystal Briana Garland

Electrical & Computer Engineering Theses & Dissertations

The electron beam emission from a LTZ-2 (lead titanate-zirconate) ferroelectric cathode was characterized. The purpose was to determine the operation range for this type of electron emitter. The experimental apparatus consisted of a high voltage driving circuit with a charging voltage up to 30kV. A solid-state SCR switch is used to generate the high voltage pulse which induces a polarization change. Current densities on the order of 80A/cm² 30kV were achieved. The electron beam profile is Guassian. At long anode-cathode distances the measured current densities were found to be above Child-Langmuir space charge limits. The large current densities and …

A Crosstalk Correcting Router That Uses Online Noise Simulation To Route High-Speed Multichip Modules, Kenneth J. Mcclellan Jr.

Theses and Dissertations

Existing Multi Chip Module (MCM) auto-routers either ignore crosstalk or use over-simplified crosstalk approximations. Of the routers that do consider crosstalk, very few have the capability to correct crosstalk problems after they occur. This dissertation describes a router that not only has an internal crosstalk model for high speed MCMs which is more accurate than that of other existing routers, but also has the capability to use an online simulator to more accurately determine noise levels. After crosstalk problems occur, the router has the ability to correct these problems. Through memory usage reductions and routing efficiency improvements, this maze router …

On The Adaptive Multi-Stage Detector For Cancellation Of Multiuser Interference In Cdma Wireless Communication Systems, Nadir Sezgin

Dissertations

The classical multiple access techniques such as Frequency Division Multiple Access (FDMA) and Time Division Multiple Access (TDMA) schemes are band limited in terms of their capacity to be used for mobile radio communication. Recent developments in the area of digital signal processing, makes Code Division Multiple Access (CDMA) as a possible solution to the demand of capacity for the mobile radio communication. The capacity of CDMA is limited by multiuser interference, that is the interference from the other users.

The goal of this dissertation is to improve the multiuser CDMA detector with high Bit Error Rate (BER) performance, low …

Adaptive Space-Time Processing For Wireless Communications, Xiao Cheng Bernstein

Dissertations

Adaptive space-time processing techniques have been found to increase the capacity of two major, multiple-access wireless communication systems: Time Division Multiple Access (TDMA) and Code Division Multiple Access (CDMA).

In an IS-54 TDMA system, the frequency re-use factor has to be set to 7 so that cells with the same spectrum are separated far enough to meet a required carrier-to-interference ratio (CIR). Space processing uses multiple antennas which, in turn, provide alternative signal paths in order to cancel interferences and combat multipath fading. We have proposed the eigencanceler method and have reviewed the theoretical optimum combining and the feasible direct …

On Optimal Design And Applications Of Linear Transforms, Mehmet V. Tazebay

Dissertations

Linear transforms are encountered in many fields of applied science and engineering. In the past, conventional block transforms provided acceptable answers to different practical problems. But now, under increasing competitive pressures, with the growing reservoir of theory and a corresponding development of computing facilities, a real demand has been created for methods that systematically improve performance. As a result the past two decades have seen the explosive growth of a class of linear transform theory known as multiresolution signal decomposition. The goal of this work is to design and apply these advanced signal processing techniques to several different problems.

The …

On The Optimization Problems In Multiaccess Communication Systems, Gangsheng Wang

Dissertations

In a communication system, the bandwidth is often a primary resource. In order to support concurrent access by numerous users in a network, this finite and expensive resource must be shared among many independent contending users. Multi-access protocols control this access of the resource among users to achieve its efficient utilization, satisfy connectivity requirements and resolve any conflict among the contending users. Many optimization problems arise in designing a multi-access protocol. Among these, there is a class of optimization problems known as NP-complete, and no polynomial algorithm can possibly solve them. Conventional methods may not be efficient arid often produce …

Implementation Of A Friction Estimation And Compensation Technique, Jayesh N. Amin

Theses

This thesis reports implementation of a friction estimation and compensation technique on a special laboratory apparatus. In this work, experimental results are reported for the Coulomb friction observer.

The Coulomb friction observer estimates the total friction present in a system, assuming it to be a constant function of velocity. An extension of the observer, utilizing a coupled velocity observer, is used when velocity is not measurable. A modification to the velocity observer is also implemented. Experimental results show a remarkable improvement in the friction estimates which are also compared to the actual friction measurements. The estimates are qualitatively similar to …

Small Computer System Interface (Scsi) Universal Services For The Turbonet Parallel Computer, Artak Ohan Melkonian

Theses

TurboNet is a parallel computer with shared-memory and message-passing hybrid architecture. It employs two boards, with four digital signal processors (DSPs) each, and a host FORCE SPARC CPU-2CE board with a SCSI bus.

Software has been developed in this thesis to provide SCSI services to programs running on the DSPs. DSP programs can therefore fully control assigned SCSI devices at the SCSI command level. Transfer control modifiers ensure compatibility with most SCSI devices.

The software provides service for three SCSI access levels. The "su" SCSI universal device driver is built into the host computer's kernel and is a gateway to …