Open Access. Powered by Scholars. Published by Universities.®

Electrical and Electronics Commons™

Open Access. Powered by Scholars. Published by Universities.®

Discipline
Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 3301 - 3330 of 5738

Full-Text Articles in Electrical and Electronics

Ann Based Load Identification And Forecasting System For The Built Environment, Hosen Hasna Dec 2011

Ann Based Load Identification And Forecasting System For The Built Environment, Hosen Hasna

Durham School of Architectural Engineering and Construction: Dissertations, Theses, and Student Research

"Phantom Loads" cause energy waste in homes and the built environment as a whole. Consumers spend more than $3 billion a year on "Phantom Load" in the United States alone. The goal of this work is to conserve energy by increasing consumer awareness on their energy usage and appropriate tools which in turn will be reducing and /or eliminating phantom loads and mismanagement of the load in the built environment. A further goal is to improve upon existing power distribution systems in the built environment with limited hardware additions to increase energy conservation. This work investigates remote identification of load …

Go to article

An Rf Cmos Implementation Of An Adaptive Filter For Narrow-Band Interferer Suppression In Uwb Systems, Markus Both Dec 2011

An Rf Cmos Implementation Of An Adaptive Filter For Narrow-Band Interferer Suppression In Uwb Systems, Markus Both

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Ultra-wideband (UWB) technology is a new type of technology for wireless communication that is based on the transmission of low power sub-nanosecond pulses. UWB communication utilizes a large bandwidth that overlaps and is coexistent with other wireless communication standards that can be also considered as narrow-band interferers. Because UWB systems are highly susceptible to narrow-band interferers, there is a demand for interferer suppression. An adaptive filter consisting of a two-element diversity receiver that performs minimum mean square error combining (MMSE) by the LMS algorithm is proposed. Thereby the elements of the LMS algorithm as well as the receiver LNA were …

Go to article

Highly Efficient Maximum Power Point Tracking Using A Quasi-Double-Boost Dc/Dc Converter For Photovoltaic Systems, Christopher J. Lohmeier Dec 2011

Highly Efficient Maximum Power Point Tracking Using A Quasi-Double-Boost Dc/Dc Converter For Photovoltaic Systems, Christopher J. Lohmeier

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Solar photovoltaic (PV) panels are a great source of renewable energy generation. The biggest problem with solar systems is relatively low efficiency and high cost. This work hopes to alleviate this problem by using novel power electronic converter and control designs. An electronic DC/DC converter, called “Quasi-Double-Boost DC/DC Converter,” is designed for a Solar PV system. A Maximum Power Point Tracking (MTTP) algorithm is implemented through this converter. This algorithm allows the PV system to work at its highest efficiency. Different current sensing and sensorless technologies used with the converter for the MPPT algorithm are offered and tested. Design aspects …

Go to article

Nanoparticle Necklace Network Arrays Exhibiting Room Temperature Single-Electron Switching, Jennifer L. Kane Dec 2011

Nanoparticle Necklace Network Arrays Exhibiting Room Temperature Single-Electron Switching, Jennifer L. Kane

Department of Chemical and Biomolecular Engineering: Dissertations, Theses, and Student Research

A single nanoparticle is one of the most sensitive electronic devices for sensing chemicals in a gas or liquid. The conductivity of a single Au nanoparticle is significantly modulated by the binding of a molecule that alters charge by just one electron. However, the single-electron sensitivity requires cryogenic temperatures and interconnection is not easy. A patterned two-dimensional network of one-dimensional nanoparticle necklaces made up of 10 nm Au particles are fabricated and shown to exhibit similar single-electron effect at room temperature. Furthermore, the long range conductivity of over 10’s of microns makes the structure easy to self-assemble onto conventional microelectronics …

Go to article

Design Of An 866 Mhz On-Chip Frequency Synthesizer, Phaniraj Joshi Dec 2011

Design Of An 866 Mhz On-Chip Frequency Synthesizer, Phaniraj Joshi

Graduate Theses and Dissertations

There is a strong need for stable frequency references with large tuning ranges in today's communication systems. While the crystal oscillators assure good frequency stability, it is not possible to achieve a large frequency range by tuning the passive components attached to them. Frequency synthesizers are usually used for this purpose because of their ability to produce a variety of output frequencies. The Phase Locked Loop (PLL) based frequency synthesizer is the most preferred of all types of synthesizers available because of its additional features like programmability, low noise and low cost as well as high accuracy and stability. The …

Go to article

Fabrication Of Horizontal Silicon Nanowires Using A Thin Aluminum Film As A Catalyst, Khaja Hafeezuddin Mohammed Dec 2011

Fabrication Of Horizontal Silicon Nanowires Using A Thin Aluminum Film As A Catalyst, Khaja Hafeezuddin Mohammed

Graduate Theses and Dissertations

Silicon nanowires have been the topic of research in recent years for their significant attention from the electronics industry to grow even smaller electronic devices. The semiconductor industry is built on silicon. Silicon nanowires can be the building blocks for future nanoelectronic devices. Various techniques have also been reported in fabricating the silicon nanowires. But most of the techniques reported, grow vertical silicon nanowires. In the semiconductor industry, integrated circuits are designed and fabricated in a horizontal architecture i.e. the device layout is flat compared to the substrate. When vertical silicon nanowires are introduced in the semiconductor industry, a whole …

Go to article

Auto-Tuning Antenna, John Chen, Jennifer Tighe Dec 2011

Auto-Tuning Antenna, John Chen, Jennifer Tighe

Electrical Engineering

Radio transmitters and antennas have differing impedances at the output and feedpoint, depending on frequency. Modern antenna tuning methods involve manual or automatic resistance and reactance network adjustment to match transmitter and antenna impedance. This reduces power reflections to the transmitter, but introduces losses and prevents full transmitter power from being radiated at the antenna. This project utilizes a variable length antenna element to tune and match transmitter and antenna impedances, allowing efficient power transfer to the antenna. The antenna length varies from 0 to 30.5 inches. The method involves an RF signal with a maximum power of 2 watts …

Go to article

Design Of A Low Noise Amplifier For Wireless Sensor Networks, Ting Liu Dec 2011

Design Of A Low Noise Amplifier For Wireless Sensor Networks, Ting Liu

Graduate Theses and Dissertations

CMOS technology becomes important in Radio Frequency (RF) communication systems which include both a receiver and a transmitter. In a high performance radio receiver, the Low Noise Amplifier (LNA) is the first circuit, and its noise performance dominates the entire receiver. Depending upon the system in which they are used, LNAs can be designed according to various topologies and structures. The LNA needs to have matched input impedance, and at the same time it should amplify the small amplitude input signal without adding too much noise and still have the minimal power consumption. It also needs a good interface with …

Go to article

A 2-D Processor Array For Massively Parallel Image Processing, Anantha Krishna Nelliparthi Dec 2011

A 2-D Processor Array For Massively Parallel Image Processing, Anantha Krishna Nelliparthi

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

The concept of introducing image processing logic within the spatial gaps of an array of photodiodes is the key factor behind the presented work. A two-dimensional massively parallel image processing paradigm based on 8X8 pixel neighborhood digital processors has been designed. A low complexity processor array architecture along with its instruction set has been designed and fully verified on a FPGA platform. Various image processing tests have been run on the FPGA platform to demonstrate the functionality of a design that uses 12 parallel processors. The test results indicate that the architecture is scalable to support high frame rates while …

Go to article

Circular And Near-Circular Polarization States Of Evanescent Monochromatic Light Fields In Total Internal Reflection, R. M. A Azzam Nov 2011

Circular And Near-Circular Polarization States Of Evanescent Monochromatic Light Fields In Total Internal Reflection, R. M. A Azzam

Electrical Engineering Faculty Publications

Conditions for the production of near-circular polarization states of the evanescent field present in the rarer medium in total internal reflection of incident monochromatic p-polarized light at a dielectric-dielectric planar interface are determined. Such conditions are satisfied if high-index (>3.2) transparent prism materials (e.g., GaP and Ge) are used at angles of incidence well above the critical angle but sufficiently below grazing incidence. Furthermore, elliptical polarization of incident light with nonzero p and s components can be tailored to cause circular polarization of the resultant tangential electric field in the plane of the interface or circular polarization of the …

Go to article

Effect Of Copper Addition On Mechanical Properties And Electrical Conductivity Of Pp/C-Cu Bipolar Plate Composites, Anne Zulfia, Taufik Abimanyu, Verina Warga Dalam Nov 2011

Effect Of Copper Addition On Mechanical Properties And Electrical Conductivity Of Pp/C-Cu Bipolar Plate Composites, Anne Zulfia, Taufik Abimanyu, Verina Warga Dalam

Makara Journal of Technology

Effect of Copper Addition on Mechanical Properties and Electrical Conductivity of PP/C-Cu Bipolar Plate Composites. Bipolar plate is a major component in PEM fuel cell which possess main function of collecting and removing electrons from anode to cathode. Therefore, materials for bipolar plates produced must have high electrical conductivity. To obtain bipolar plate materials which is cheap, lightweight and high conductivity, so it is developed bipolar plates material based on PP/C-Cu composite. PP/C-Cu composites has been made by mixing all materials then compounding, rheomix, hot blending and hot press. Cu (Copper) has been used various from 0.1 wt%, 1 wt% …

Go to article

Application Of Empirical Orthogonal Function Models To Analyze Shoreline Change At Bangkalan Madura, Darius Arkwright, Suntoyo Suntoyo Nov 2011

Application Of Empirical Orthogonal Function Models To Analyze Shoreline Change At Bangkalan Madura, Darius Arkwright, Suntoyo Suntoyo

Makara Journal of Technology

Bangkalan’s shoreline, especially on the opposite side of Surabaya, has been evaluated to determine the morphological changes due to wave attack, near-shore current, long-shore sediment transport and coastal configuration. This research aims to determine the dominant patterns of variation of Bangkalan’s shoreline change, expressed by Eigen-function in empirical orthogonal function (EOF) models. That was started with data collection such as oceanographic data (wave and tidal), bathymetry and topographic map and sediment data. All data was used for forecasting two-monthly shoreline. Coordinate of two-monthly shoreline was used as input of EOF model. The first Eigen mode is a profile of shoreline …

Go to article

The Effectiveness Of Anaerobic Baffled Reactor And Rotating Biological Contactor In Batik Wastewater Treatment, Augustinus Ignatius Kristijanto, Widhi Handayani, Purwanti Asih Anna Levi Nov 2011

The Effectiveness Of Anaerobic Baffled Reactor And Rotating Biological Contactor In Batik Wastewater Treatment, Augustinus Ignatius Kristijanto, Widhi Handayani, Purwanti Asih Anna Levi

Makara Journal of Technology

Batik is one of popular arts of Indonesia. The batik industries in Sragen, Central Java, are prepared to compete in global market. In order to realize that objective, batik products should fulfill some qualifications, one of which is “environmental friendliness”. As batik production is usually generating wastewater which pollutes the environment, the technology of wastewater treatment should be developed to solve the problem. This preliminary study has been done to assess the effectiveness of anaerobic baffled reactor (ABR) and rotating biological contactor (RBC) in batik wastewater treatment. In 40 days of treatment period, the ABR performance in reducing pollutants showed …

Go to article

Physical Characterization And Desulfurization Of Biobriquette Using Calcium-Based Adsorbent, Mahidin Mahidin, Asri Gani, Khairil Khairil Nov 2011

Physical Characterization And Desulfurization Of Biobriquette Using Calcium-Based Adsorbent, Mahidin Mahidin, Asri Gani, Khairil Khairil

Makara Journal of Technology

Combustion of coal and co-combustion of their co-fuel contribute to gas emissions. Among the gas emissions are SOx, NOx, CO and CO2. Introduction of calcium based adsorbent is addressed to absorb SO2 that release to the atmosphere during the combustion process. Objective of the research is at first to observe the physical characteristics of biobriquettes as a function of briquette compositions (coal to palm kernel shell ratios) and Ca/S ratios (Ca in adsorbent and S in briquette) using a natural adsorbent (shellfish waste). The second objective is to investigate desulfurization characteristics as a function of Ca/S ratios and desulfurization temperatures …

Go to article

Medium Density Fibreboard Made Of Acetylated Sludge From Paper Mill, Luthfi Hakim, Evalina Herawati, I Nyoman Jaya Wistara Nov 2011

Medium Density Fibreboard Made Of Acetylated Sludge From Paper Mill, Luthfi Hakim, Evalina Herawati, I Nyoman Jaya Wistara

Makara Journal of Technology

Medium Density Fibreboard Made of Acetylated Sludge from Paper Mill. Research of using sludge as raw material for making medium density fibreboard (MDF) was useful to create additional value of sludge. The objective of the research was to evaluate physical properties, mechanical properties, and durability of MDF from acetylated sludge in 4 levels of acetate anhydride (0%, 3%, 5%, and 7%) with 3 replicates. The MDF was made using dry process. After materials were mixed with adhesives, they were pressed using hotpress under 170 oC temperature and 45 Pa pressure for 25 minutes. The size of the MDF sample was …

Go to article

Cassava Pulp As A Biofuel Feedstock Of An Enzymatic Hydrolysis Proces, Djuma’Ali Djuma’Ali, Nonot Soewarno, Sumarno Sumarno, Dyah Primarini, Wahono Sumaryono Nov 2011

Cassava Pulp As A Biofuel Feedstock Of An Enzymatic Hydrolysis Proces, Djuma’Ali Djuma’Ali, Nonot Soewarno, Sumarno Sumarno, Dyah Primarini, Wahono Sumaryono

Makara Journal of Technology

Cassava pulp, a low cost solid byproduct of cassava starch industry, has been proposed as a high potential ethanolic fermentation substrate due to its high residual starch level, low ash content and small particle size of the lignocellulosic fibers. As the economic feasibility depends on complete degradation of the polysaccharides to fermentable glucose, the comparative hydrolytic potential of cassava pulp by six commercial enzymes were studied. Raw cassava pulp (12% w/v, particle sizeμm) hydrolyzed by both commercial pectinolytic (1) and amylolytic (2) enzymes cocktail, yielded 70.06% DE. Hydrothermal treatment of cassava pulp enhanced its susceptibility to enzymatic cleavageas compared to …

Go to article

Alos/Palsar Image Processing Using Dinsar And Log Ratio For Flood Early Detection In Jakarta Based On Land Subsidences, Dodi Sudiana, Mia Rizkinia Nov 2011

Alos/Palsar Image Processing Using Dinsar And Log Ratio For Flood Early Detection In Jakarta Based On Land Subsidences, Dodi Sudiana, Mia Rizkinia

Makara Journal of Technology

Flood that occurred in Jakarta is not only influenced by rainfall, urban planning system and drainage alone, but also may be involved land subsidence (LS). LS is possible in because Jakarta stands on top of layers of sediments and the presence of ground water consumption in very large quantities. In this research, the Advanced Land Observing Satellite (ALOS)/Phased Array type L-band Synthetic Aperture Radar (PALSAR) data was processed to determine the level of LS in Jakarta area and its relation to flood potential area. Differential interferometry method (DInSAR) was performed on two PALSAR data with different acquisition years, i.e. 2007 …

Go to article

Analytical And Computational Simulation Approaches To Design Low Energy Glass Block, Floriberta Binarti, Agustinus Djoko Istiadji, Prasasto Satwiko, Priyo Tri Iswanto Nov 2011

Analytical And Computational Simulation Approaches To Design Low Energy Glass Block, Floriberta Binarti, Agustinus Djoko Istiadji, Prasasto Satwiko, Priyo Tri Iswanto

Makara Journal of Technology

Analytical and Computational Simulation Approaches to Design Low Energy Glass Block. An environmentally friendly process was developed to produce a low embodied energy glass block from waste glasses. The energy efficiency of the glass block is represented by its thermal conductance (U)

Go to article

Improvement Of High Temperature Oxidation Of Low Carbon Steel Exposed To Ethanol Combustion Product At 700 °C By Hot-Dip Aluminizing Coating, Mohammad Badaruddin Nov 2011

Improvement Of High Temperature Oxidation Of Low Carbon Steel Exposed To Ethanol Combustion Product At 700 °C By Hot-Dip Aluminizing Coating, Mohammad Badaruddin

Makara Journal of Technology

Low carbon steel (AISI 1005) was coated by hot-dipping into a molten Al-10% Si bath at 700 °C for 18s. After hotdipping treatment, the coating layers consisted of Al, Si, FeAl3, τ5-Fe2Al8Si, and Fe2Al5. The bare steel and the aluminized steel were isothermally oxidized at 700 °C in ethanol combustion product at atmospheric pressure for 49 h. The aluminized steel shows good performance in high temperature oxidation because the formation of Al2O3 layer on the coating surface. The growth of iron oxide nodules on the surface coating was accelerated by rapid outward diffusion of Fe-ions due to the presence of …

Go to article

Establishment Code Hand Palm (Palm Code) 2d Gabor-Based Method, I Ketut Gede Darma Putra, Wira Bhuana, Erdiawan Erdiawan Nov 2011

Establishment Code Hand Palm (Palm Code) 2d Gabor-Based Method, I Ketut Gede Darma Putra, Wira Bhuana, Erdiawan Erdiawan

Makara Journal of Technology

Establishment Code Hand Palm (Palm Code) 2D Gabor-Based Method. Palmprint is relatively new in physiological biometrics. Palmprint ROI segmentation and feature extraction are two important issues in palm print recognition. This paper introduces two steps in the center of mass moment method for ROI segmentation that will be applied in the Gabor 2D filter to obtain palm code as palmprint feature vector. Normalized Hamming distance was used to measure the similarity degrees of two feature vectors of palmprint. The system was tested using database 1000 palmprint images generated from 5 samples from each of the 200 persons randomly selected with …

Go to article

Flutter Analysis Of Rx-420 Balistic Rocket Fin Involving Rigid Body Modes Of Rocket Structures, Novi Andria Nov 2011

Flutter Analysis Of Rx-420 Balistic Rocket Fin Involving Rigid Body Modes Of Rocket Structures, Novi Andria

Makara Journal of Technology

Flutter Analysis of RX-420 Balistic Rocket Fin Involving Rigid Body Modes of Rocket Structures. Flutter is a phenomenon that has brought a catastrophic failure to the flight vehicle structure. In this experiment, flutter was analyzed for its symmetric and antisymmetric configuration to understand the effect of rocket rigid modes to the fin flutter characteristic. This research was also expected to find out the safety level of RX-420 structure design. The analysis was performed using half rocket model. Fin structure used in this research was a fin which has semispan 600 mm, thickness 12 mm, chord root 700 mm, chord tip …

Go to article

Flexible Connection Elastomeric Rubber As A Pounding Resisting Element Between Two Adjacent Buildings, Yuskar Lase, James Jatmiko Oetomo Nov 2011

Flexible Connection Elastomeric Rubber As A Pounding Resisting Element Between Two Adjacent Buildings, Yuskar Lase, James Jatmiko Oetomo

Makara Journal of Technology

Flexible Connection Elastomeric Rubber as a Pounding Resisting Element between Two Adjacent Buildings To solve pounding problem of two adjacent buildings, structural designer usually employs a dilatation between the structures or make the two structures as a monolith structure. Other alternative is by using an elastomeric rubber as a pounding resisting element between the two structures. Effectiveness in applying elastomeric rubber component as flexible connection of two adjacent structures is the main focus of this paper. Various simulations such as structure models, earthquake excitations and openings in gap element are studied. Observation of maximum structural responses will be performed for …

Go to article

Optimation Of Nitrogen And Phosphorus In Azolla Growth As Biofertilizer, Hany Handajani Nov 2011

Optimation Of Nitrogen And Phosphorus In Azolla Growth As Biofertilizer, Hany Handajani

Makara Journal of Technology

Nitrogen is one of the most important minerals for living organisms. Azolla is known as a small water fern which can fix nitrogen through the symbiotic association with the blue green algae Anabaena. Experimental studies were carried out in the glass house, investigating the growth of Azolla using different levels of nitrogen and phosphorus in the media. The experiment used 12 treatments with 3 levels of nitrogen (0, 5, and 10 mg atom/L) and 4 levels of phosphorus (0, 10, 20, and 30 mg atom/l) in a factorial design with 3 replicates. The results show that the highest biomass for …

Go to article

Application Of Principal Component Proximity Transform And Geostatistics Methods For Volume Shale Distribution As Reservoir Characreristic Imaging In Seismic 3d, Nur Islami Nov 2011

Application Of Principal Component Proximity Transform And Geostatistics Methods For Volume Shale Distribution As Reservoir Characreristic Imaging In Seismic 3d, Nur Islami

Makara Journal of Technology

Application of Principal Component Proximity Transform and Geostatistics Methods for Volume Shale Distribution as Reservoir Characreristic Imaging in Seismic 3D. Principal component proximity transform (PCPT) technique was used to predict the content of volume shale into seismic data in reservoir modeling framework. The goal in this research is to get the volume shale imaging in three dimensions and allow for reservoir modelling. The reservoir modelling requires an integrated quantitative and qualitative data sources collected separately, such as well and seismic data. Integrating PCPT and Geostatistic methods can generate the detail information for characterization of reservoir’s properties. Finally, it shows that …

Go to article

Antibacterial Activity Of Papaya Leaf Extracts Against Pathogenic Bacteria, Elisa Friska Romasi, Jessica Karina, Adolf Jan Nexson Parhusip Nov 2011

Antibacterial Activity Of Papaya Leaf Extracts Against Pathogenic Bacteria, Elisa Friska Romasi, Jessica Karina, Adolf Jan Nexson Parhusip

Makara Journal of Technology

It was reported that the extracts of papaya leaves could inhibit the growth of Rhizopus stolonifer. Antibacterial activity of Carica papaya leaf extracts on pathogenic bacteria was observed in this study. Papaya leaves were extracted by using maceration method and three kinds of solvents: ethanol, ethyl acetate, and hexane. Papaya leaf extracts were tested against Bacillus stearothermophilus, Listeria monocytogenes, Pseudomonas sp., and Escherichia coli by agar diffusion method. The objectives of this study were to determine extract ability against pathogenic bacteria, to observe the influence of pH, NaCl, and heat on extracts ability, and to observe extract ability against B. …

Go to article

Liquid Crystal Devices For Optical Communications And Sensing Applications, Sunish Mathews Nov 2011

Liquid Crystal Devices For Optical Communications And Sensing Applications, Sunish Mathews

Doctoral

This thesis is focussed on the design and development of liquid crystal based tunable photonic devices for applications in optical communications and optical sensing, with an emphasis on all-fiber device configuration. The infiltration of liquid crystals into photonic crystal fiber provides a suitable common platform to design and fabricate simple and compact all-fiber tunable photonic devices which can be easily integrated with optical fiber networks and sensing systems. Based on the infiltration of liquid crystals – materials with high dielectric anisotropy, into photonic crystal fibers a common platform is developed to address the need for electronically tunable photonic devices with …

Go to article

Impacts Of Plug-In Electric Vehicle On Residential Electric Distribution System Using Stochastic And Sensitivity Approach, Henry Chigozie Ureh Nov 2011

Impacts Of Plug-In Electric Vehicle On Residential Electric Distribution System Using Stochastic And Sensitivity Approach, Henry Chigozie Ureh

Master's Theses

Plug-in Electric Vehicles (PEVs) are projected to become a viable means of transportation due to advances in technology and advocates for green and eco-friendly energy solutions. These vehicles are powered partially, or in some cases, solely by the energy stored in their battery packs. The large sizes of these battery packs require large amount of energy to charge, and as the demand for PEV increases, the increase in energy demand needed to recharge these PEV batteries could pose problems to the present electric distribution system. This study examines the potential impacts of PEV on a residential electric distribution system at …

Go to article

Poincaré Sphere Representation Of The Fixed-Polarizer Rotating-Retarder Optical System, R. M.A. Azzam Nov 2011

Poincaré Sphere Representation Of The Fixed-Polarizer Rotating-Retarder Optical System, R. M.A. Azzam

Electrical Engineering Faculty Publications

The trajectory of the polarization state of a monochromatic light beam after it passes through a fixed linear polarizer and a rotating linear retarder of arbitrary retardance Δ is determined on the Poincaré sphere. The three-dimensional figure-8 contour is shown to be the line of intersection of a right-circular cylinder with the sphere. The cylinder is parallel to the polar (s3) axis, touches the sphere at the equator (at the point that represents the linear polarization transmitted by the fixed polarizer), and has a radius r=sin2(Δ/2). Projections of the trajectory in the coordinate planes of the …

Go to article

Three-Dimensional Polarization States Of Monochromatic Light Fields, R. M.A. Azzam Oct 2011

Three-Dimensional Polarization States Of Monochromatic Light Fields, R. M.A. Azzam

Electrical Engineering Faculty Publications

The 3×1 generalized Jones vectors (GJVs) [ExEyEz]t (t indicates the transpose) that describe the linear, circular, and elliptical polarization states of an arbitrary three-dimensional (3-D) monochromatic light field are determined in terms of the geometrical parameters of the 3-D vibration of the time-harmonic electric field. In three dimensions, there are as many distinct linear polarization states as there are points on the surface of a hemisphere, and the number of distinct 3-D circular polarization states equals that of all two-dimensional (2-D) polarization states on the Poincaré sphere, of which only two are circular states. The subset of 3-D polarization …

Go to article

Development And Prototyping Of A Ground Fault Circuit Interrupter For 3-Phase 480 Volt Systems, Matthew R. Norlander Oct 2011

Development And Prototyping Of A Ground Fault Circuit Interrupter For 3-Phase 480 Volt Systems, Matthew R. Norlander

Master's Theses

Ground Fault Circuit Interrupter (GFCI) technology was first introduced in the NEC in 1971, yet four decades later the technology has not been introduced to a great extent outside of the home environment. This thesis introduces the difficulties encountered in low-voltage three phase ground fault current detection, and adopts a previously patented tripping scheme to develop and prototype a digital relay for 3-phase 480 volt systems capable of the sensitivity and speed required for personnel safety. Results demonstrate the feasibility of the concept and suggest commercial development should be pursued. The prototype is capable of mA sensitivity and reliably detects …

Go to article

First Prev Next Last