Electrical and Electronics Commons^™

Monitoring And Regression Based Modelling Of End Winding Vibration In Large Synchronous Generators, David Shally

Doctoral

This research project was set up to monitor, on an ongoing basis, the condition of the end windings and their support structures of a 288 MVA 2-pole synchronous generator with a known end winding vibration problem
Excessive vibration at the end windings was caused by the natural frequencies of individual end bars (local) and of the entire end winding structure (global) being at or close to the magnetic forcing frequency of 100 Hz. Resonant vibration such as this has been a cause of major failures in machines of the same type in the past, resulting in significant down time ranging …

Monitoring And Regression Based Modelling Of End Winding Vibration In Large Synchronous Generators., David Shally

Masters

This research project was set up to monitor, on an ongoing basis, the condition of the end windings and their support structures of a 288 MVA 2-pole synchronous generator with a known end winding vibration problem Excessive vibration at the end windings was caused by the natural frequencies of individual end bars (local) and of the entire end winding structure (global) being at or close to the magnetic forcing frequency of 100 Hz. Resonant vibration such as this has been a cause of major failures in machines of the same type in the past, resulting in significant down time ranging …

Methods And Considerations For Testing Resistive Memories, Adam David Johnson

Boise State University Theses and Dissertations

Resistive random access memory (RRAM) has been the topic of many research papers in recent years, as companies begin to look for non-volatile alternatives to NAND Flash. The standard testing methodologies for single devices do not work for most of the RRAM technologies, so new methods must be developed. Parasitic capacitance will destroy the device under test without current compliance circuitry. A test structure with the capability to apply current compliance in either direction was designed, simulated, and tested with electrical results. Pulses greater than 4.0 V were delivered with 100 μA current compliance, and parasitic capacitance was kept below …

Design Of An Rf Cmos Power Amplifier For Wireless Sensor Networks, Hua Pan

Graduate Theses and Dissertations

The Power Amplifier (PA) is the last Radio Frequency (RF) building block in a transmitter, directly driving an antenna. The low power RF input signal of the PA is amplified to a significant power RF output signal by converting DC power into RF power. Since the PA consumes a majority of the power, efficiency plays one of the most important roles in a PA design. Designing an efficient, fully integrated RF PA that can operate at low supply voltage (1.2V), low power, and low RF frequency (433MHz) is a major challenge. The class E Power Amplifier, which is one type …

Smart Home Prototype, Logistics & Planning, David G. Guzman^, Virgilio Gonzalez*

COURI Symposium Abstracts, Spring 2012

No abstract provided.

Laser-Induced Multi-Energy Processing In Diamond Growth, Zhiqiang Xie

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Laser-induced multi-energy processing (MEP) introduces resonant vibrational excitations of precursor molecules to conventional chemical vapor deposition methods for material synthesis. In this study, efforts were extended to explore the capability of resonant vibrational excitations for promotion of energy efficiency in chemical reactions, for enhancement of diamond deposition, and for control of chemical reactions. The research project mainly focused on resonant vibrational excitations of precursor molecules using lasers in combustion flame deposition of diamond, which led to: 1) promotion of chemical reactions; 2) enhancement of diamond growth with higher growth rate and better crystallizations; 3) steering of chemical reactions which lead …

Information Encryption And Retrieval In Mid-Rf Range Using Acousto-Optic Chaos, Monish Ranjan Chatterjee, Abhinay Kundur

Electrical and Computer Engineering Faculty Publications

In recent work, low-frequency AC signal encryption, decryption and retrieval using system-parameter based keys at the receiver stage of an acousto-optic (A-O) Bragg cell under first-order feedback have been demonstrated [1,2]. The corresponding nonlinear dynamics have also been investigated using the Lyapunov exponent and the so-called bifurcation maps [3]. The results were essentially restricted to A-O chaos around 10 KHz, and (baseband) signal bandwidths in the 1-4 KHz range. The results have generally been satisfactory, and parameter tolerances (prior to severe signal distortion at the output) in the ±5% - ±10% range have been obtained.

Periodic AC waveforms, and a …

Tolerance Limit For Trucks With Excess Load In Transport Regulation In Indonesia, Sigit Pranowo Hadiwardoyo, Raden Jachrizal Sumabrata, Mohammed Ali Berawi

Makara Journal of Technology

Reliability of a road is mandatory since damaged will impede the traffic. Destruction is caused by various factors; one of the most important factors is excess load. Overload may give the load of each axle of a vehicle exceeds the determined standard. This condition occurs in trucks exceeding the load limit. In designing the structure of a road based on the method of Directorate General of Highways Ministry of Public Works of the Republic of Indonesia, axle load calculated in equivalent-number, or known as equivalent axle load (EAL), of 8.16 tons of standard axle. Total equivalent-number over the service life …

Earthquake Damage Intensity Relationship For Residential Houses In West Sumatra, Febrin Anas Ismail, Abdul Hakam, Fauzan Fauzan

Makara Journal of Technology

The Sumatra 30 September 2009 earthquake has damaged hundred thousand buildings in West Sumatra Province. The earthquake is located in 100 km offshore of Padang City, the Capital City of the province. Survey has been conducted to assess the damage of the building in few days after the earthquake. In this survey, the damage of buildings are categorised into 3 level that are heavily, moderate and slightly damages. This paper explores the level damage of building and then the intensity of the shaking in the affected area. Then based on the coordinate of every building location, the buildings are scattered …

Evaluation Of Universitas Indonesia’S Recharge Pond Performance And Potential Utilization For Raw Water Source, Nyoman Suwartha, Resky Agaslian Pramadin

Makara Journal of Technology

Evaluasi Kinerja Waduk Resapan UI dan Potensi Pemanfaatannya sebagai Sumber Air Baku. Waduk resapan Universitas Indonesia (UI) telah dibangun sejak 5 tahun yang lalu. Namun kegiatan monitoring dan evaluasinya sangat minim dilakukan. Tujuan dari studi ini adalah untuk mengetahui laju resapan, dan untuk mengevaluasi kondisi kuantitas dan kualitas air waduk resapan selama musim kemarau dan penghujan. Pengukuran kedalaman muka air, intensitas curah hujan dan penguapan dilakukan untuk menentukan ketersediaan air, laju resapan, dan imbangan air waduk. Sejumlah air permukaan diambil dari waduk resapan dan sungai di tiga titik sampling untuk mengetahui kondisi kualitas air eksisting. Hasil studi menunjukkan tidak ada …

Effect Of Methanol Induction And Incubation Time On Expression Of Human Erythropoietin In Methylotropic Yeast Pichia Pastoris, Adi Santoso, Neng Herawati, Yana Rubiana

Makara Journal of Technology

Erythropoietin (EPO) is a glycoprotein hormone consists of 165 amino acids and has molecular mass of 30,400 Daltons. The large quantities of these hormone required to satisfy clinical demand are currently met by recombinant expression in mammalian cell, namely chinese hamster ovary (CHO). Pichia pastoris has become popular yeast based protein production systems to substitute mammalian expression systems. P. pastoris is capable to use methanol as sole carbon and energy source. In this study, recombinant human EPO (rhEPO) protein obtained by expressing the hEPO gene in methylotropic yeast P. pastoris, strain X33. The present work was carried out to study …

Fuel Saving Strategy In Spark Ignition Engine Using Fuzzy Logic Engine Torque Control, Aris Triwiyatno, Sumardi Sumardi

Makara Journal of Technology

In the case of injection gasoline engine, or better known as spark ignition engines, an effort to improve engine performance as well as to reduce fuel consumption is a fairly complex problem. Generally, engine performance improvement efforts will lead to increase in fuel consumption. However, this problem can be solved by implementing engine torque control based on intelligent regulation such as the fuzzy logic inference system. In this study, fuzzy logic engine torque regulation is used to control the throttle position entered by the driver to achieve optimal engine torque. An engine torque vs. throttle position and engine speed mapping …

An Agri-Food Supply Chain Model To Enhance The Business Skills Of Small-Scale Farmers Using Corporate Social Responsibility, Wahyudi Sutopo, Muh. Hisjam, Yuniaristanto Yuniaristanto

Makara Journal of Technology

In general, small-scale vegetable farmers experience problems in improving the safety and quality of vegetables for supplying high-class consumers in modern retailers. Farmer Group and/or Cooperative (FGC) should be able to assist its members to meet the relevant provisions of modern retail on product specifications, delivery terms, and internal business requirements. This study proposed an agri-food supply chain (ASC) model that involves the corporate social responsibility (CSR) activities to enhance the business skills of the FGC as supplier of modern retailer. Multi-objective optimization programming is developed to determine the amount and timing of supply, level of farmers training skills, quality …

Robot X, Alan Truong, Alex Haag

Computer Engineering

The following report outlines the design decisions behind Robot X for the 2012 Cal Poly Roborodentia competition held annually during Open House. This investigation includes detailed overview of Robot X's sensory system, driving system, conveyor belt system, and can compartment system. In addition, basic hardware and software design are explored.

Corrosion Rate Of Carbon Steel For Flowline And Pipeline As Transmission Pipe In Natural Gas Production With Co2 Content, Andi Rustandi, Muhammad Adyutatama, Enriko Fadly, Norman Subekti

Makara Journal of Technology

The purpose of this research is to investigate the corrosion rate of carbon steel as flowline and pipeline in natural gas production with CO2 content. The influence of variety of conditions that represent the actual conditions in practice such as CO2 partial pressure and solution composition, particularly NaCl percentage were performed. Research conducted by polarization test and simulation methods using PREDICTTM software. The result of this research is used to illustrate the level of corrosion rate of typical carbon steel i.e. API 5L X-52 occurred in natural gas pipelines due to the effect of dissolved CO2. From the experiments obtained …

Modification Of Flow Structure Over A Van Model By Suction Flow Control To Reduce Aerodynamics Drag, Harinaldi Harinaldi, Budiarso Budiarso, Warjito Warjito, Engkos Achmad Kosasih, Rustan Tarakka, Sabar Pangihutan Simanungkalit, I Gusti Made Fredy Lay Teryanto

Makara Journal of Technology

Automobile aerodynamic studies are typically undertaken to improve safety and increase fuel efficiency as well as to find new innovation in automobile technology to deal with the problem of energy crisis and global warming. Some car companies have the objective to develop control solutions that enable to reduce the aerodynamic drag of vehicle and significant modification progress is still possible by reducing the mass, rolling friction or aerodynamic drag. Some flow control method provides the possibility to modify the flow separation to reduce the development of the swirling structures around the vehicle. In this study, a family van is modeled …

Age, Gender, And Muscle Strength: A Study Based On Indonesian Samples, Henny Henny, Hardianto Iridiastadi, Iftikar Zahedi Sutalaksana

Makara Journal of Technology

Age and gender have been commonly used as a main criterion in accepting a job aplicant, but it is usually not clear how these affect job performance. While a number of recent studies have been done that describe the relationships between age, gender, and participants capacity (e.g., muscle strength), the results have been inconclusive. In Indonesia, in particular, such issues have been rarely investigated, and it is still important to study the issue since the relationships between these factors are population-specific. This study aimed at describing the relationships between age and muscle strength among workers for both genders. Ninety-six male …

Circularly Polarized Microstrip Array Antenna For Ground Segment In Quasi-Zenith Satellite System, Fitri Yuli Zulkifli, Eko Tjipto Rahardjo

Makara Journal of Technology

In satellite communication system, antenna plays an important role. Therefore, the antenna must meet some requirements, such as high gain, circular polarization, and good directivity. In this paper, a four element linear array triangular patch microstrip antenna with cross slot is designed to be used for Quasi-Zenith satellite system. A simulation study as well as experimental study was carried out. The simulation showed that the 3 dB axial ratio bandwidth of 87 MHz (2.569-2.656 GHz) is achieved while the measured results showed 96 MHz (2.556-2.652 GHz). The linear array of 4 element antenna has a gain of 13.73 dB and …

Concurrent Engineering Of Tolerance Synthesis And Process Selection For Products With Multiple Quality Characteristcs Considering Process Capability, Mohamad Imron Mustajib

Makara Journal of Technology

The existences of variances that are very difficult to be removed from manufacturing processes provide significance of tolerance to the product quality characteristics target of customer functional requirement. Furthermore, quality loss incurred due to deviation of quality characteristics of the target with a specified tolerance. This article discusses the development of concurrent engineering optimization model of tolerance design and manufacturing process selection on product with multiple quality characteristics by minimizing total costs in the system, namely total manufacturing cost and quality loss cost as functions of tolerance, also rework and scrap costs. The considered multiple quality characteristics have interrelated tolerance …

Pineapple Liquid Waste As Nata De Pina Raw Material, Agus Sutanto

Makara Journal of Technology

This research aims to study the quantity, quality, ecological and economic feasibility of nata de pina production (NP) from pineapple liquid waste (PLW). The design of the study employs complete random design (CRD) with three treatments: PLW without nutrients addition (A), PLW nutrients addition (B), and PLW stored for six months with nutrients addition (C). The nata de pina’s production factors measured were weight, thickness, fiber content, color, brightness, and residual waste. The highest weight was reached in treatment B (899 grams), followed by treatment A (616.4 grams), and C (477.8 grams). The thickness of NP of the height and …

Modeling Of A New Structure Of Precision Air Conditioning System Using Secondary Condenser For Rh Regulation, Aries Subiantoro, Nasruddin Nasruddin, Feri Yusivar, Muhammad Idrus Al-Hamid, Bagio Budiardjo

Makara Journal of Technology

A dynamic mathematical model for a new structure of precision air conditioning (PAC) has been developed. The proposed PAC uses an additional secondary condenser for relative humidity regulation compared to a basic refrigeration system. The work mechanism for this system and a vapour-compression cycle process of the system are illustrated using psychrometric chart and pressure-enthalpy diagram. A non-linear system model is derived based on the conservation of mass and energy balance principles and then linearized at steady state operating point for developing a 8th-order state space model suited for multivariable controller design. The quality of linearized model is analyzed in …

Optimizing Fermentation Medium To Produce Cyclosporin A Using Response Surface Methodology, Rofiq Sunaryanto

Makara Journal of Technology

Response surface methodology (RSM) is a three factorial model which illustrates the relationship between one or more independent variables. RSM can be used to optimize the fermentation medium for the production of Cyclosporin A from the isolate Tolypocladium inflatum. The optimal point of the response surface area is predicted by using a seconddegree polynomial model and applying the statistic model obtained from the central composite design (CCD). The results of optimizing the fermentation medium for Cyclopsorin using the three independent variables of glucose, casein, and KH2PO4 show that all three of the independent variables affect the production of Cyclosporin A. …

Electro-Luminescent Display Device, Michael E. Miller, Joseph R. Bietry, Ronald S. Cok

AFIT Patents

An electro-luminescent display includes a first array of light-emitting elements. Each of these light-emitting elements has an optical element. A second array of light-emitting elements also includes a second optical element different from the first. One or more row lines are electrically connected to either light-emitting elements in the first array of light-emitting elements or light-emitting elements in the second array of light-emitting elements. One or more column lines provide a data signal to the first and second array of light-emitting elements. A driver circuit delivers common information to the light-emitting elements in both the first and second arrays in …

Electromagnetic Characterization Of Inhomogeneous Media, Marcus A. Sitterly

Theses and Dissertations

Developed two permittivity profile extraction algorithms for inhomogeneous materials. These two algorithms were created using discrete and continuous approaches. The discrete method used a piece-wise constant permittivity assumption that allowed the use of homogeneous wave equations. Using laboratory data and a theoretical formulation, the permittivity of each piece-wise constant layer within the material was extracted using a root search algorithm. The continuous approach solved the problem using inhomogeneous wave equations. These equations were used to extract a linear permittivity profile using laboratory data and a root search.

Trade-Offs In A 1 Tbps Mimo Communication System Between An Airship And An Array Of Ground Receive Antennas, Adam R. Brueggen

Theses and Dissertations

As demand for higher data-rate wireless communications increases, so will the interest in multiple-input and multiple-output (MIMO) systems. In a single transmitter, single receiver communication system, there is a fundamental limit to the data-rate capacity of the system proportional to the systems bandwidth. Since increasing the bandwidth is expensive and limited, another option is increasing the system's capacity by adding multiple antennas at the transmitter and receiver to create a MIMO communication system. With a T transmitter, R receiver MIMO communication system, TR channels are created which allow extremely high data-rates. MIMO systems are attractive because they are extremely robust …

Optimum Concentration Ratio Analysis Using Dynamic Thermal Model For Concentrated Photovoltaic System, John T. Avrett

Theses and Dissertations

Concentrated photovoltaic (PV) technology represents a growing market in the field of terrestrial solar energy production. As the demand for renewable energy technologies increases, further importance is placed upon the modeling, design, and simulation of these systems. Given the U.S. Air Force cultural shift towards energy awareness and conservation, several concentrated PV systems have been installed on Air Force installations across the country. However, there has been a dearth of research within the Air Force devoted to understanding these systems in order to possibly improve the existing technologies. This research presents a new model for a simple concentrated PV system. …

Electro-Luminescent Area Illumination Device, Michael E. Miller, Ronald S. Cok

AFIT Patents

An electro-luminescent area illumination device that includes two or more area emitters formed on a substrate. Each of the two or more area emitters emit light having different area illumination profiles.

Kreative Outlets, Travis Crist, Steve Clark, Jason Peressini

Computer Engineering

With the widespread use of smart phones and the advancement of WiFi technologies, people now have the Internet at their fingertips at all times. Home automation and control has the possibility of becoming the next big technology that can utilize the abundant availability of the Internet. This paper documents the findings and results of a project aimed at developing the infrastructure needed for a home automation system that is accessible anywhere. We implemented a system that utilized a web enabled ethernet connection and RF wireless technology to control AC outlets and provide the user with feedback information about the status …

Car Alarm System, David Lane

Electrical Engineering

This project entails the design and implementation of a car alarm system for a 1977 Volkswagen Beetle.

Rapid Battery Interchange System, Mason Borda

Electrical Engineering

As our nation strives towards a departure from widespread use of fossil fuels, we must focus on a plan for what is to be the substitute for Internal Combustion Engine vehicles as well as the infrastructure to support this. The most popular alternative to the internal combustion engine is the electrically propelled vehicle, one that can provide us with many benefits including simplified construction, lower operational costs, and for the driving enthusiasts more torque. The prevailing issue in the widespread acceptance and use of the electric vehicle thus far is “range anxiety”. Range anxiety is defined as “The fear of …