Electrical and Electronics Commons^™

A New Algorithm For Piecewise Affine System Identification And Its Application To A Mems Switch, Niel Canty

Theses

Over the past ten years, hybrid systems, and piecewise affine (PWA) systems in particular have been viewed as viable option for modelling nonlinear systems. Many methods have been developed to cater for the identification of a PWA model from input/output data. This thesis focuses on the clustering based identification approach. This method uses a Least Squares (LS) identification algorithm which, in this thesis, is shown to perform poorly in practice. The clustering based algorithm is also limited by the number of initialisation parameters that need to be chosen. These parameters have a significant influence on the resulting PWA model accuracy, …

A Novel Waveform For Emergency Services Mobile Ad-Hoc Networks : The Link Layer Perspective, Sebastian Helmle

Theses

Existing wireless communication systems of emergency services mainly enable ordinary unicast or broadcast voice communications. The increasing demand for data services such as messaging, file transfer, maps, etc requires those long-range communication systems to provide higher data rates while maintaining robustness against link failures. In this thesis, various aspects of a link layer design specifically for narrowband mobile ad-hoc networks (MANETs) that are targeted at emergency services are investigated.

The major aspect of this thesis is the optimisation of a time division multiple access (TDMA) design considering both efficient and reliable multicast resource reservation. An approach to mathematically describe a …

3d Printed Electromagnetic Transmission And Electronic Structures Fabricated On A Single Platform Using Advanced Process Integration Techniques, Paul I. Deffenbaugh

Open Access Theses & Dissertations

3D printing has garnered immense attention from many fields including in-office rapid prototyping of mechanical parts, outer-space satellite replication, garage functional firearm manufacture, and NASA rocket engine component fabrication. 3D printing allows increased design flexibility in the fabrication of electronics, microwave circuits and wireless antennas and has reached a level of maturity which allows functional parts to be printed. Much more work is necessary in order to perfect the processes of 3D printed electronics especially in the area of automation. Chapter 1 shows several finished prototypes of 3D printed electronics as well as newly developed techniques in fabrication. Little is …

Situational Assessment Of Multi Sensor Data, Eduardo Estrada

Open Access Theses & Dissertations

The importance of sensors has grown dramatically through the years, specially since they have the capability to create a specific task. Multiple sensor fusion is an area that has rapidly grown due to its multiple and beneficial applications. It is common to develop devices that have multiple sensors; however, the fusion of these multiple sensors to make a single output is remarkable. In fact, this is the way people chose to try to model the human body which has innumerable sensors and makes one decision. The development of sensor fusion not only helps create innovations in technology, but has the …

Digitally Manufactured Spatially Variant Photonic Crystals, Javier Jair Pazos

Open Access Theses & Dissertations

Metamaterials and photonic crystals are engineered composites that exhibit electromagnetic properties superior to those found in nature. They have been shown to produce novel and useful phenomena that allow extraordinary control over the electromagnetic field. One of these phenomena is self-collimation, an effect observed in photonic crystals in which a beam of light propagates without diffraction and is forced to flow in the direction of the crystal. Self-collimation however, like many of the mechanisms enabled through dispersion engineering, is effective in directions only along the principal axes of the lattice. To this effect, a general purpose synThesis procedure was developed …

Frequency Selective Surfaces For Extreme Applications, Jay Houston Barton

Open Access Theses & Dissertations

It is known that for high-power microwaves and other extreme environments, the use of resonant metallic elements in frequency selective surfaces can be problematic. The solution developed within this Dissertation to solve these problems was to use guided-mode resonance phenomenon to create all-dielectric frequency selective surfaces that could survive these extreme environments.

To fully understand how these devices work, three different computational electromagnetic methods are formulated and implemented. The formulation of these methods start with the differential form of Maxwellâ??s equation and are derived all the way down to the final simulation state. This is done sequentially and all the …

Location Management And Hybrid Geo-Routing For Urban Vehicular Networks, Aisling O'Driscoll

Theses

In recent years the motivation for comfort applications e.g. infotainment, file exchange and vehicle to vehicle (V2V) multiplayer gaming amongst others, has emerged as an active area of vehicular communications and network research. The success of such applications relies on the ability of a geo-routing protocol to deliver communication packets in a frequently disconnected communication environment. To do this, the location of the destination vehicle must first be determined and secondly, must reliably deliver the packet from source to destination. To determine the location of a target vehicle towards which packets can be forwarded, geo-routing algorithms utilise a location service …

Harmonic Power Compensation Capacity Of Shunt Apf And Its Relationship To Design Parameters, Shafiuzzaman Khadem, Malabika Basu, Michael Conlon

Articles

VSI-based three-phase; power exchange mechanism; switching dynamics; three-phase systems; active losses; single-phase systems; power tetrahedron phasor diagram; shunt active power filter; harmonic power compensation capacity; four-wire systems; hysteresis band current control

Electron – Phonon Interaction In Multiple Channel Gan Based Hfets: Heat Management Optimization, Romualdo A. Ferreyra

Theses and Dissertations

New power applications for managing increasingly higher power levels require that more heat be removed from the power transistor channel. Conventional treatments for heat dissipation do not take into account the conversion of excess electron energy into longitudinal optical (LO) phonons, whose associated heat is stored in the channel unless such LO phonons decay into longitudinal acoustic (LA) phonons via a Ridley path. A two dimensional electron gas (2DEG) density of ~5×10¹²cm^-2 in the channel results in a strong plasmon–LO phonon coupling (resonance) and a minimum LO phonon lifetime is experimentally observed, implying fast heat removal from …

Wind Energy In Ireland - An Analysis Of Percentage Error In Forecasting, Michael Mcdonald

Dissertations

This research aimed to examine the percentage error in forecasting of wind energy using datasets from a small wind farm in Ireland. Furthermore, the study aimed to compare this calculated data to the national forecasting percentage errors. Internationally, the electrical sector and society are undergoing a revolution in terms of 'green economy'. This paradigm shift towards renewable energy technologies is recognised as a priority, with diminution of finite fossil fuels at its core. Renewable energy as a sector has provided significant financial stimulation to global economies in recent years. Moreover, wind energy has provided significant amounts of clean electricity throughout …

Development Of An Optical Sensor For Real-Time Weed Detection Using Laser Based Spectroscopy, Arie Jacobus Paap

Theses: Doctorates and Masters

The management of weeds in agriculture is a time consuming and expensive activity, including in Australia where the predominant strategy is blanket spraying of herbicides. This approach wastes herbicide by applying it in areas where there are no weeds. Discrimination of different plant species can be performed based on the spectral reflectance of the leaves. This thesis describes the development of a sensor for automatic spot spraying of weeds within crop rows. The sensor records the relative intensity of reflected light in three narrow wavebands using lasers as an illumination source.

A prototype weed sensor which had been previously developed …

Optimized Integrated Software Package For Classification Of Small Airway Dysfunction Using Genetic Algorithms, Elias Estrada

Open Access Theses & Dissertations

Due to the similarity in the symptoms of respiratory disorders, an accurate diagnosis could be a difficult task. Regarding asthma as the main focus of this research, early detection of small airway impairment could represent a better opportunity for timely diagnosis. An integrated software package (ISP) based on the impulse oscillometry technique, has been developed to serve as an important tool for clinicians during classification of asthma severities on children [1]. The current version of the ISP was tested with data obtained during several years by Dr. Homer Nazeran and Dr. Michael Goldman from 110 Hispanic children [2], providing an …

Design Of Three Different Particle Size Distributions In Silver Paste Through Computer Simulation For Higher Electrical Conductivity, Kyungdeok Jang

Open Access Theses & Dissertations

In the field of printed electronics technology, researchers have tried to print highly conductive electrodes with fine width and height in order to manufacture high performance devices.

The purpose of this research is to print particle monolayer silver patterns which have better electrical conductivity than existing ones. The key idea of this experiment is to analyze silver inks with different sized particles. Let us consider a particle monolayer pattern printed with silver ink consisting of mono-sized particles. Inside of the pattern, there are some vacant spaces between the particles, which can lead to low electrical conductivity and discontinuity of the …

Growth And Analysis Of Micro And Nano Cdte Arrays For Solar Cell Applications, Brandon Adrian Aguirre

Open Access Theses & Dissertations

CdTe is an excellent material for infrared detectors and photovoltaic applications. The efficiency of CdTe/CdS solar cells has increased very rapidly in the last 3 years to ~20% but is still below the maximum theoretical value of 30%. Although the short-circuit current density is close to its maximum of 30 mA/cm2, the open circuit voltage has potential to be increased further to over 1 Volt. The main limitation that prevents further increase in the open-circuit voltage and therefore efficiency is the high defect density in the CdTe absorber layer. Reducing the defect density will increase the open-circuit voltage above 1 …

Analysis Of Power Efficiency Of A Direct-Driven Locally Fabricated Permanent Magnet Ac Generator For Small-Scale Wind Power Applications In Tanzania, Mussa Iddi Mgwatu Dr.

Tanzania Journal of Engineering and Technology (TJET)

The use of direct-driven permanent magnet alternating current (AC) generators offers the opportunity to reduced costs and increased system efficiency. This type of generator could be the best alternative for rural population whom are not connected to the national grid. To improve the design and efficiency of locally fabricated generators, it is imperative to characterize both their mechanical and electrical parameters. This paper presents the analysis of power efficiency of the synchronous permanent AC generator locally fabricated in Tanzania. In this case, load resistance and rotational speed are characterized using designed experiment. The output current and voltage of the generator …

The Marine Electronic Highway And Routeing Scheme Along The West Coast Of India And Sri Lanka : Feasibility Study : "Aiming Towards A Sustainable Maritime Transportation System", Sellakkannu I. Abul Kalam Azad

World Maritime University Dissertations

No abstract provided.

Mems Cantilever Sensor For Thz Photoacoustic Chemical Sensing And Spectroscopy, Nathan E. Glauvitz

Theses and Dissertations

Sensitive Microelectromechanical System (MEMS) cantilever designs were modeled, fabricated, and tested to measure the photoacoustic (PA) response of gasses to terahertz (THz) radiation. Surface and bulk micromachining technologies were employed to create the extremely sensitive devices that could detect very small changes in pressure. Fabricated devices were then tested in a custom made THz PA vacuum test chamber where the cantilever deflections caused by the photoacoustic effect were measured with a laser interferometer and iris beam clipped methods. The sensitive cantilever designs achieved a normalized noise equivalent absorption coefficient of 2.83x10^-10 cm^-1 W Hz^-1/2 using a 25 …

Physical Design Of A Smart Camera With Integrated Digital Pixel Sensors Using A 0.13Μm 8-Layer Metal Cmos Process, Mahir K. Gharzai

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

The design of cameras has historically kept imagery and computational circuitry isolated in an attempt to maximize image quality by improving pixel pitch and routing density. Although this technique has worked in creating high density arrays of pixels for large resolution imagers, it has never been able to achieve high framerate computational operations.

A radical approach is introduced to solve this dilemma by creating compact, low- power pixel elements with built-in analog-to-digital converters that directly interface with digital logic. These pixels are capable of integrating alongside logic cells and to create an array of pixels inside the processor that can …

Synthesis Of Tungsten Oxide Nanowires Onto Ito Glass Using T-Cvd, Tomy Abuzairi, Bohr-Ran Huang, Tzu-Ching Lin

Makara Journal of Technology

Tungsten oxide is an n-type semiconductor with interesting physical and chemical properties that make it suitable for various technological applications. Tungsten oxide nanowires were synthesized not only at low temperature but also without the use of any catalysts. The tungsten oxide nanowires were synthesized at 550 °C with tungsten layers onto the ITO glass using thermal chemical vapor deposition (T-CVD). The SEM image shows that the tungsten oxide nanowires are effectively grown with the 200 nm tungsten film. The Raman spectra shoulder at ~690 cm-1 proves the synthesized of tungsten oxide nanowires.

Radiation Characteristics Of A Planar Strip Dipole Antenna And A Slot Dipole Antenna For Thz Applications, Catur Apriono, Eko Tjipto Rahardjo

Makara Journal of Technology

The development of a THz system often requires a device that is used to radiate or detect THz waves. One way to fulfill this requirement is to use an antenna. Therefore, we need to consider the radiation characteristics of an antenna working in the THz region. In this paper, we present simulation study of two dipole antennas, i.e. a planar strip dipole antenna and a slot dipole antenna. The simulation results show that a planar strip dipole antenna has a better radiation efficiency (more than 95%) compared to the slot dipole. It also shows that an efficiency of more than …

The Effect Of Pressing Temperature And Time On The Quality Of Particle Board Made From Jatropha Fruit Hulls Treated In Acidic Condition, Apri Heri Iswanto, Fauzi Febrianto, Yusuf Sudo Hadi, Surdiding Ruhendi, Dede Hermawan

Makara Journal of Technology

The high of pH of jatropha fruit hulls causes the negative properties of particleboard made from this material. Adjusting the particle acidity and pressing conditions (temperature and time) is among the technical modifications available to improve this particleboard’s properties. Particle acidity has been adjusted in a previous research project, and immersing the particles in acetic acid was found to be the best treatment in this preliminary research. In order to improve the particleboard’s properties, an experiment was conducted to determine the best pressing temperature and time. The objective of the research was to evaluate the influence of pressing temperature and …

Microgrid Development Using A Grid Tie Inverter, Hartono Budi Santoso, Budiyanto Budiyanto

Makara Journal of Technology

The use of renewable energy sources (RES), especially photovoltaic (PV), to meet the demand of electrical energy has been getting a great deal of attention as an alternative solution to electrical energy deficit problems. RES are being applied in power systems in a variety of configurations including microgrid systems. One of the characteristics of a microgrid is capability to supplying power to grid when there is an excess power to supply local load. This research examines the chances of saving power consumption from grid using power converters grid tie inverter (GTI) in a microgrid configuration. The test is done by …

Surface Treatment Of Fly Ash For Improving The Tensile Strength Of Fly Ash/Unsaturated Polyester Composites, Sugiman Sugiman, Paryanto Dwi Setyawan

Makara Journal of Technology

The paper presents the surface treatment of fly ashes using acid and alkali solution on the tensile strength of the fly ash/unsaturated polyester (UP) composites. Sulfuric acid (H2SO4), hydrofluoric acid (HF) and sodium hydroxide (NaOH) solution with concentration of 0%, 5%, 10%, 15%, and 20% (by weight) were used for surface treatment of fly ashes. Generally, the tensile strength of the treated fly-ash/UP composites shows a significant increase compared to the untreated fly ash. Of all surface treatments studied, the optimum tensile strength was obtained at a concentration of 10%. At this concentration, at a fly ash content of 30% …

Recycling Roof Tile Waste Material For Wall Cover Tiles, Ambar Mulyono, Silfia Mona Aryani, Joko Lulut

Makara Journal of Technology

Prior research on roof tile waste treatment has attempted to find the appropriate technology to reuse old roof tile waste by create wall cladding materials from it. Through exploration and experimentation, a treatment method has been discovered to transform the tile fragments into artificial stone that resembles the shape of coral. This baked clay artificial stone material is then processed as a decorative element for vertical surfaces that are not load-bearing, such as on the interior and exterior walls of a building. Before applying the fragments as wall tiles, several steps must be taken: 1) Blunting, which changes the look …

Semiconductor Thermal Neutron Detector, Toru Aoki, Aki Miyake, Takayuki Nakano, Akifumi Koike, Hisashi Morii, Hidenori Mimura

Makara Journal of Technology

The CdTe and GaN detector with a Gd converter have been developed and investigated as a neutron detector for neutron imaging. The fabricated Gd/CdTe detector with the 25 mm thick Gd was designed on the basis of simulation results of thermal neutron detection efficiency and spatial resolution. The Gd/CdTe detector shows the detection of neutron capture gamma ray emission in the 155Gd(n, g)156Gd, 157Gd(n, g)158Gd and 113Cd(n, g)114Cd reactions and characteristic X-ray emissions due to conversion-electrons generated inside the Gd film. The observed efficient thermal neutron detection with the Gd/CdTe detector shows its promise in neutron radiography application. Moreover, a …

Design Of A Low Power Cargo Security Device Using A Micropower Ultra-Wideband Impulse Radar, Brian M. Wihl

Master's Theses

Each year, thousands of cargo containers are broken into during shipping, costing billions of dollars in lost and damaged goods. In addition to removing its contents, intruders can also add unwanted and dangerous materials to a container, posing a threat to National Security. The possibilities of cargo container break-ins require that the containers go through check points at which they are physically searched. These searches often require the opening of the container, unloading and inspecting all cargo, and then loading the container and resealing it. This is a long and costly process.

Because of the high costs of break-ins and …

Portable Nano-Hydro Power Generator For The Dc House Project, Andrew Aw, James Biggs

Electrical Engineering

This senior project report explains the construction and design of a small, portable water generator that converts kinetic energy flowing in small creeks to electrical energy as a renewable source of energy for the DC House. The DC House, in short, is a project to build a self-sustainable house for Third World countries that utilizes only DC electricity. The system consists of two converters and a charge controller for a 12V lead-acid battery. The first converter converts the hydro generator voltage output to 15 Volts for safe and proper charging of the lead-acid battery by the charge controller. The second …

Microfluidics Guided By Redox-Magnetohydrodynamics (Mhd) For Lab-On-A-Chip Applications, Vishal Sahore

Graduate Theses and Dissertations

Unique microfluidic control actuated by simply turning off and on microfabricated electrodes in a small-volume system was investigated for lab-on-a-chip applications. This was accomplished using a relatively new pumping technique of redox-magnetohydrodynamics (MHD), which as shown in this dissertation generated the important microfluidic features of flat flow profile and fluid circulation. MHD is driven by the body force, FB = j × B, which is the magnetic part of the Lorentz force equation, and its direction is given by the right hand rule. The ionic current density, j, was generated in an equimolar solution of potassium ferri/ferro cyanide by applying …

A Wide Bandgap Silicon Carbide (Sic) Gate Driver For High Temperature, High Voltage, And High Frequency Applications, Ranjan Raj Lamichhane

Graduate Theses and Dissertations

The potential of silicon carbide (SiC) for modern power electronics applications is revolutionary because of its superior material properties including substantially better breakdown voltage, power density, device leakage, thermal conductivity, and switching speed. Integration of gate driver circuitry on the same chip, or in the same package, as the power device would significantly reduce the parasitic inductance, require far less thermal management paraphernalia, reduce cost and size of the system, and result in more efficient and reliable electrical and thermal performance of the system.

The design of a gate driver circuit with good performance parameters in this completely new under-development …

Finding The Maximum And Minimum Magnitude Responses (Gains) Of Third-Order Filters Without Calculus, Kenneth V. Cartwright, Patrick Russell, Edit J. Kaminsky

Electrical Engineering Faculty Publications

The maximum and minimum gains (with respect to frequency) of third-order low-pass and high-pass filters are derived without using calculus. Our method uses the little known fact that extrema of cubic functions can easily be found by purely algebraic means. PSpice simulations are provided that verify the theoretical results.