Electrical and Electronics Commons^™

Real-Time Internal Temperature Estimation And Health Monitoring For Igbt Modules, Ze Wang

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Field experiences have demonstrated that power semiconductor devices, such as insulated-gate bipolar transistors (IGBTs), are among the most fragile components of power electronic converters. Thermomechanical stresses produced by temperature variations during operational and environmental loads are the major causes of IGBT degradation. As the devices are often operated under complex working conditions, temperature variations and the associated damage are difficult to predict during the converter design stage. A promising approach—online health monitoring and prognosis for power semiconductor devices—that can avoid device failure and effectively schedule maintenance has attracted much interest.

This dissertation research focused on real-time accurate internal temperature estimation …

Safety Airway For Small Unmanned Aerial Vehicles Using A Gas Particles Behavior Analogy, Pablo Rangel

Open Access Theses & Dissertations

The United States Federal Aviation Administration (FAA) implemented the Part 107 legislation to allow the flight of Unmanned Aerial Vehicles (UAV) for commercial use (i.e. package deliveries, power transmission line inspections, etc.) in the National Airspace System (NAS). As a consequence of the newly introduced rules, there is an increased risk for accidents involving injured bystanders or damaged to property. The work within this document defines a UAV to UAV safety distance model that acts as a range sensor enabled "elastic bubble". The length of the UAV safety bubble contracts and expands upon changing airway wind speed conditions. It also …

Bragg Gratings In Polarization Maintaining Optical Fiber As Three Dimensional Strain Sensor, Joel Quintana

Open Access Theses & Dissertations

Fiber-Bragg Gratings (FBG) for Structural Health Monitoring (SHM) have been studied extensively as they offer electrically passive operation, electromagnetic interference (EMI) immunity, high sensitivity and multiplexing as compared to conventional electric strain sensors. FBG sensors written within polarization maintaining (PM) optical fiber offer ad- ditional dimensions of strain measurement, greatly reducing the number of sensors needed to properly monitor a structure. This reduction however, adds complexity to the dis- crimination of the sensorâ??s optical response to its corresponding applied strains. This Dissertation defines the set of algorithms needed to measure planar strain using PM-FBGs exclusively. It defines the minimum number …

Organic-Inorganic Graphite And Transition Metal Dichalcogenide Based Composites For 3d Printing, Jorge Alfredo Catalan Gonzalez

Open Access Theses & Dissertations

This project was multipronged to help fuse together topics of additive manufacturing and two-dimensional (2D) layered materials, and studying the mechanical and electrical properties of the composites produced. The composites are made from the thermoplastic polymer acting as a matrix and the graphite and 2D transition metal dichalcogenides (TMDs) serving as the filler or reinforcement. Different concentrations of TMD's were added to the matrix to study the effect of composition on the mechanical and electrical properties. To shed insights into the mechanical properties, test coupons were produced as "dog bone" structures for tensile testing using the ASTM D638 type 5 …

Advances In Chemical Vapor Deposition Growth Of Molybdenum Disulfide For Photodetectors And Flexible Electronics, Carlos Francisco De Anda Orea

Open Access Theses & Dissertations

The conversion of light into electrical signals is at the basis of technologies that affect our daily lives. Applications, including video imaging, optical communications, biomedical imaging, security, night-vision, gas sensing and motion detection have reached a high level of maturity due to the development of high-performance materials, large-scale production, and integration technologies. Currently conventional photodetectors made of Silicon (Si) or III-V compounds are about to reach their maximum efficiency, and every time it is harder to get a noticeable improvement in performance of sensors based on these materials, not to mention the complicated fabrication methods to achieve just a few …

Automatic Patch Classification And Diffusion In Adaptive, Luis Alonso Ponce

Open Access Theses & Dissertations

Multi-Frame image restoration is a form of Super-Resolution (SR) which consists of combining multiple Low-Resolution (LR) images in order to reconstruct a single High Resolution (HR) image. In this Thesis we improved a spatially-adaptive SR scheme, based on the framework of Optimal Recovery (OR), whereby the block-by-block processing is done based on the properties of the corresponding local LR image data patches. The bandwidth parameter is adapted based on the local variance of each corresponding block from all LR images that contribute to the HR image block to be reconstructed. Also, an optimal regularization parameter needs to be chosen for …

Software Modelling For Real World Faults On Ac Transmission Protective Systems Analysis And Effects, Iandale Tualla

Theses and Dissertations

The Electric Power Utilities serves many diverse customers from regular households to major processing plants that develop parts for gasoline vehicles. Those varying customer usages has adverse effects on the Electric Grid in many ways, that requires continuing analysis by the engineers and technical skills specialists who keep the Electric Grid stable. Several papers have been written about harmonics and Non- Sinusoidal waveforms and its effect on the Electric Grid. This thesis will exam a realworld fault event on a transmission line, its effects on the AC Transmission Protection Systems (TPS) that provides electrical energy to a nonlinear load, specifically …

Minimum Time Control Of Paralleled Boost Converters, Shishir Patel

Dissertations, Master's Theses and Master's Reports

Demand for electrification is booming in both, traditional and upcoming generations of technological advancements. One of the constituent blocks of these electrified systems is Power conversion. Power conversion systems are often constructed by paralleling multiple power converter blocks for high performance and reliability of overall system. An advanced control technique is developed with an aim to optimize system states of heterogeneous power converters within minimum time while maintaining feasible stress level on individual power converter blocks. Practical implementation of real-time controller and performance improvement strategies are addressed. Experimental results validating high performance control scheme, and sensitivity analysis of system states …

A Testbed Design For Monitoring The Long-Term Spatial-Temporal Dynamics Of Underwater Acoustic Channels, Krishna Chaitanya Poduru

Dissertations, Master's Theses and Master's Reports

The underwater acoustic network testbed helps to validate the theoretical results and bridge the gap between experimental results. Characterizing and modeling the spatial-temporal dynamics of underwater acoustic channels is essential to developing efficient and effective physical-layer communication algorithms and network protocols. This work dedicates to designing a testbed system to measure the spatial-temporal dynamics of underwater acoustic channels. The collected measurements will shed insights into the spatial-temporal correlation of underwater acoustic channels and will be used to evaluate the theoretical algorithms that are designed to model the spatial-temporal dynamics and to exploit the spatial-temporal dynamics for more efficient and effective …

Integrated Circuit Wear-Out Prediction And Recycling Detection Using Radio-Frequency Distinct Native Attribute Features, Randall D. Deppensmith

Theses and Dissertations

Radio Frequency Distinct Native Attribute (RF-DNA) has shown promise for detecting differences in Integrated Circuits(IC) using features extracted from a devices Unintentional Radio Emissions (URE). This ability of RF-DNA relies upon process variation imparted to a semiconductor device during manufacturing. However, internal components in modern ICs electronically age and wear out over their operational lifetime. RF-DNA techniques are adopted from prior work and applied to MSP430 URE to address the following research goals: 1) Does device wear-out impact RF-DNA device discriminability?, 2) Can device age be continuously estimated by monitoring changes in RF-DNA features?, and 3) Can device age state …

Phased Helical Antenna Array For Cubesat Application, Kameron Lacalli

Undergraduate Honors Theses

CubeSats communication links are typically slow due to their power and size restrictions. However, a low power, high speed down link connection can allow for greater data collection and relaying, pushing the capability of 1U CubeSats beyond what is traditionally thought possible. Investigated here is the feasibility of a 11 Mb/s down link connection on a 1U CubeSat, accomplished via 2x2 helical antenna phased array operating on the 802.11 standard. Using a phased array also allows for beam steering to secure connection with the ground station when the on board ADCS may not provide precise pointing capability of the CubeSat, …

Adaptive Environments For Enabling Senior Citizens: An Holistic Assessment Tool For Housing Design And Iot-Based Technologies, Matteo Zallio, Damon Berry, Niccolò Casiddu

Conference papers

The population of older adults will continuously increase over the coming decades. As they get older, people will require assistance and regular monitoring, with higher costs for welfare system and families. Two vital aspects of a healthy lifestyle, are domestic autonomy and maintenance of relationships within the neighborhood. This leads to an interesting research issue: “Could houses and appliances have the potential to improve autonomy and quality of life of citizens? Which methods and tools could enhance wellbeing and healthy conditions? The house has the potential to be a safe, adaptive environment, integrated with technologies for life support. This work …

Optimizing Supply Chain Collaboration Based On Agreement Buyer-Supplier Relationship With Network Design Problem, Wahyudi Sutopo, Ayu Erliza, Arien Heryansyah

Makara Journal of Technology

In recent years, the rising competitive environment with shorter product life cycles and high customization forces industries to increase their flexibility, speed up their response, and enhance concurrent engineering designs. To integrate these prospects, supply chain collaboration becomes a pertinent strategy for industries to strengthen their competitiveness. The network design problem is used to implement supply chain collaboration. In the buying and selling process, sharing information between buyer and supplier are important to obtain a transaction decision. The optimimum supply chain profit can be identified by mathematical model of network design problem. The Mathematical Model takes into consideration the uncertainity …

Effect Of Milling On The Densification Of Sic-Basedcomposites From Polysilazane, Alfian Noviyanto, Toshiyuki Nishimura

Makara Journal of Technology

High density SiC-based composites from polysilazane were fabricated by high energy milling and hot pressing. After cross-linking at 200 °C, the polysilazane was pyrolysed at 1000 °C in N2 for 2 h to form amorphous Si-C-N-O followed by high energy milling for 1 h. Milled amorphous Si-C-N-O was sintered in hot pressing at 1600 and 1700 °C for 1 h in vacuum under the applied pressure of 50 MPa. Although no sintering additives were used, dense SiC-based composites were obtained with this method. Sintered density was 3.04 g/cm3, while only 2.57 g/cm3 for amorphous Si-C-N-O without milling. It is suggested …

Characterization And Utilization Of Calcium Oxide (Cao) Thermally Decomposed From Fish Bones As A Catalyst In The Production Of Biodiesel From Waste Cooking Oil, Aldes Lesbani, Sabat Okta Ceria Sitompul, Risfidian Mohadi, Nurlisa Hidayati

Makara Journal of Technology

Thermal decomposition of fish bones to obtain calcium oxide (CaO) was conducted at various temperatures of 400, 500, 800, 900, 1000, and 1100 °C. The calcium oxide was then characterized using X-ray diffractometer, FTIR spectrophotometer, and SEM analysis. The calcium oxide obtained from the decomposition at 1000 °C was then used as a catalyst in the production of biodiesel from waste cooking oil. Diffraction pattern of the calcium oxide produced from decomposition at 1000 °C showed a pattern similar to that of the calcium oxide produced by the Joint Committee on Powder Diffraction Standard (JCDPS). The diffractions of 2q values …

Thermoeconomic Optimization Of Cascade Refrigeration System Using Mixed Carbon Dioxide And Hydrocarbons At Low Temperature Circuit, Nasruddin Nasruddin, Arnas Arnas, Ahmad Faqih, Niccolo Giannetti

Makara Journal of Technology

Many applications and industrial processes require very low cooling temperature, such as cold storage in the biomedical field, requiring temperature below -80 °C. However, single-cycle refrigeration systems can only achieve the effective cooling temperature of -40 °C and, also, the performance of the cycle will decrease drastically for cooling temperatures lower than -35°C. Currently, most of cascade refrigeration systems use refrigerants that have ozone depletion potential (ODP) and global warming potential (GWP), therefore, in this study, a cascade system is simulated using a mixture of environmentally friendly refrigerants, namely, carbon dioxide and a hydrocarbon (propane, ethane or ethylene) as the …

Developing Road Infrastructure Route Planning: Increasing Feasibility Of Toll Road Project, Mohammed Ali Berawi, Teuku Yuri Zagloel, Perdana Miraj, Abdur Rohim Boy Berawi, Wellsi Titaheluw, Saipol Bari Bin Abd Karim

Makara Journal of Technology

Indonesian government attempts to improve connectivity and to increase regional activities in Sumatera Island through the development of Trans Sumatera Toll Road (TSTR). However, despite its benefits to local economic development in Sumatera, the project shows low feasibility due to a low amount of investment. It can be attributed from the lack of planning in the initial phase to produce a comprehensive route that considers the various potentials of the regions. Thus, this research aims to investigate alternative route planning of Trans Sumatera Toll Road particularly in this paper for Central Sumatera by studying Gross Regional Domestic Product (GRDP), population …

Thermal And -Γ –Ray Irradiation Effects On The Ionic Conductivity Of (Licl)X(Montmorillonite)1-X, Safei Purnama, Aziz Khan Jahja, Takeshi Sakuma

Makara Journal of Technology

Compositesof montmorillonite (MMT) - lithium salts have been prepared using a simple process of powders mixing followed by heating. The powders resulting from this method are expected to beionic conductors with a high ionic conductivity characteristics. This characteristics is also further improved by employing gamma-ray irradiation technique at specified irradiation doses. The best results were obtained for the (LiCl)0.5(MMT)0.5 composite with a room temperature ionic conductivity of 2.192 mS/cm, which then increases to ~5 mS/cm after gamma irradiation at a dose of 400 kGy. This value is equivalent to the value of the ionic conductivity of current commercial rechargeable lithium …

Design Of The Human Assembly Strategy In A Self-Optimizing Assembly Cell: A Case Study Of Indonesians, Novie Susanto, Ratna Purwaningsih, Kharisma Panca Kurniawati

Makara Journal of Technology

This paper presents a continuing study of the human cognitive aspect application in the technical systems. The last studies design a human-centered design based on the German culture. The result shows a significant difference of human performance between Germans and Indonesians. Therefore, this study examines the human cognitive model based on Indonesian culture to investigate whether the different cognitive model based on the culture aspect can improve the human performance. The study was conducted on 60 people classified by age, young (16-34 years old) and old (older than 34 years old). Participants render predictions on an assembly activity for two …

Expression And The Functional Study Of Fusion Proteins Α-Amylase And Hemolysin- Αas An Application In Biofilm Polysaccharide Degradation, Gede Yuda Sugiarta, Anggoro Wiseso, Siska Yuliana Sari, Etri Dian Kamila, Vanessa Geraldine, Diana Christina, Muhammad Hanifi, Dwiantari Satyapertiwi, Robby Hertanto, Budiman Bela, Masafumi Yohda, Muhamad Sahlan

Makara Journal of Technology

Biofilm is an aggregate of consortium bacteria that adhere to each other on a surface. It is usually protected by the exopolysaccharide layer. Various invasive medical procedures, such as catheterization, endotracheal tube installation, and contact lens utilization, are vulnerable to biofilm infection. The National Institute of Health (NIH) estimates 65% of all microbial infections are caused by biofilm. Periplasmic α-amylase (MalS) is an enzyme that hydrolyzes α-1, 4- glicosidic bond in glycogen, starch, and others related polysaccharides in periplasmic space. Another protein called hemolysin-α (HlyA) is a secretion signal protein on C terminal of particular peptide in gram negative bacteria. …

Identity‐Based Schemes For A Secured Big Data And Cloud Ict Framework In Smart Grid System, Feng Ye, Yi Qian, Rose Qingyang Hu

Electrical and Computer Engineering Faculty Publications

Smart grid is an intelligent cyber physical system (CPS). The CPS generates a massive amount of data for efficient grid operation. In this paper, a big data‐driven, cloud‐based information and communication technology (ICT) framework for smart grid CPS is proposed. The proposed ICT framework deploys hybrid cloud servers to enhance scalability and reliability of smart grid communication infrastructure. Because the data in the ICT framework contains much privacy of customers and important data for automated controlling, the security of data transmission must be ensured. In order to secure the communications over the Internet in the system, identity‐based schemes are proposed …

Electric Smart Load Meter, Johnny Tran

Electrical Engineering

This project details the design of an electric meter that reads the signals of any device plugged into an outlet and displays cost readings that may potentially reduce power consumption. The sensor monitors whether a plugged in device continuously consumes power after completely charging up. For a charging device, the current remains constant until the device reaches 100% charge. Once the device becomes fully charged, the current discontinues for proper power usage. A unique aspect of the meter is that it displays cost per hour, day, and year. Displaying the cost per unit of time creates awareness for customers, potentially …

Accumulator Volume Sensor Final Project Report, Chris Naughton, Kinwei Yu, Michael George

Mechanical Engineering

Accumulator Volume Sensing Team has developed two sensor designs aimed at detecting the position of the piston within a 4024 accumulator. The two designs include the use of a Renishaw LMA10 magnetic encoder and a SpectraSymbol HotPot linear potentiometer. The magnetic encoder solution drastically increases the accuracy of sensing the piston position compared to the current solutions of both a string-pot and linear variable differential transformer while costing slightly less. The linear potentiometer seeks to provide a solution that drastically decreases the cost compared to the present sensing methods. Both designs call for a modification to one half of the …

Identity-Based Schemes For A Secured Big Data And Cloud Ict Framework In Smart Grid System, Feng Ye, Yi Qian, Rose Qingyang Hu

Electrical and Computer Engineering Faculty Publications

Smart grid is an intelligent cyber physical system (CPS). The CPS generates a massive amount of data for efficient grid operation. In this paper, a big data-driven, cloud-based information and communication technology (ICT) framework for smart grid CPS is proposed. The proposed ICT framework deploys hybrid cloud servers to enhance scalability and reliability of smart grid communication infrastructure. Because the data in the ICT framework contains much privacy of customers and important data for automated controlling, the security of data transmission must be ensured. In order to secure the communications over the Internet in the system, identity-based schemes are proposed …

Final Design Report: Grasp Data Acquisition Project Axon Vr, Michael Erberich, Jack Schultz, Tyler Yeaman

Mechanical Engineering

No abstract provided.

Integrated Circuit Design For Hybrid Optoelectronic Interconnects, Kehan Zhu

Boise State University Theses and Dissertations

This dissertation focuses on high-speed circuit design for the integration of hybrid optoelectronic interconnects. It bridges the gap between electronic circuit design and optical device design by seamlessly incorporating the compact Verilog-A model for optical components into the SPICE-like simulation environment, such as the Cadence design tool.

Optical components fabricated in the IME 130nm SOI CMOS process are characterized. Corresponding compact Verilog-A models for Mach-Zehnder modulator (MZM) device are developed. With this approach, electro-optical co-design and hybrid simulation are made possible.

The developed optical models are used for analyzing the system-level specifications of an MZM based optoelectronic transceiver link. Link …

Evolution And Rationale For United States Department Of Defense Electromagnetic Pulse Protection Standard, George H. Baker Iii

School of Integrated Sciences - Faculty Scholarship

The United States (US) Department of Defense (DoD) Electromagnetic Pulse (EMP) protection standard offers a solid basis for protecting commercial communication, data, and control facilities. Because of the standard’s shielded barrier and test requirements, it is not surprising that there is a strong temptation within industry and government to dismiss the MIL-STD 188-125 approach in favor of less rigorous protection methods. It is important to understand that US DoD EMP protection standard for fixed facilities, MIL-STD-188-125, reflects an evolution by trial and error that spanned a period of decades beginning with the acquisition of the Minuteman Missile System in the …

Design, Analysis, And Simulation Of A Jitter Reduction Circuit (Jrc) System At 1ghz, Run Bin Yu

Master's Theses

The clock signal is considered as the “heartbeat” of a digital system yet jitter which is a variation on the arrival time of the clock edge, could undermine the overall performance or even cause failures on the system. Deterministic jitter could be reduced during the designing process however random jitter during operation is somehow less-controllable and unavoidable. Being able to remove jitter on the clock would therefore play a vital role in system performance improvement.

This thesis implements a 1GHz fully feedforward jitter reduction circuit (JRC) which can be used as an on-chip IP core at clock tree terminals to …

Isopropyl Alcohol Pump For Printed Circuit Boards Using An Arduino, Lawrence Zhu

Computer Engineering

No abstract provided.

Active Contact Lens - Low Power Backscattering Sensor-To-Antenna Integration Circuitry, Caleb B. Porter

Electrical Engineering

The Active Contact Lens measures the cornea-scleral radius of the wearer’s eye, which correlates to intraocular pressure (IOP), Glaucoma’s primary indicator. IOP varies throughout the day, and is drastically different from person to person, so constantly measuring it over a period of a few days can provide individualized tracking of the disease’s development and will help doctors develop personalized treatment schedules to treat the disease more precisely.

The Active Contact Lens sensor measures strain, based on the cornea-scleral radius, and reports the results wirelessly, to allow monitoring of an individual’s IOP over time. The lens is powered similarly to a …