Electrical and Electronics Commons^™

Pressure Switch Tester, Michael Starasinich, Andrew Dobson, Jordan Huschen, Mitchell Smith, Melvin Brown Iii

Honors Capstones

Abstract—- The Pressure Switch Test Stand is a comprehensive and automated testing solution designed to streamline the actuation and validation of simultaneously. At the core of the system is a PLC-controlled architecture that enables precise control and simulation of pressure conditions, replicating real-world scenarios to ensure accurate and reliable switch performance.

This test stand integrates robust mechanical fixtures, a reliable pneumatic control system, custom-designed electrical circuits, and a modular software interface, working in unison to deliver consistent and high-fidelity testing outcomes. Each pressure switch undergoes a sequence of pressure ramps and holds, with the system continuously monitoring switch states, activation …

Development Of A Cost-Effective Daq For Measuring Brake Performance In Race Cars, Adrin Alias

2025 Spring Honors Capstone Projects - Archive

This project explores the feasibility of creating a cost-effective data acquisition (DAQ) system for high-speed, real-time brake performance testing of Formula SAE racecars. The research addresses the limitations of the current MoTeC DAQ system currently employed by the team, which is costly and time-consuming to set up for on-car testing. The team will use a brake dynamometer for steady-state comparisons of different brake pad compounds (senior design project), but evaluating real-world performance requires on-car testing. By systematically comparing various hardware platforms, sensors, communication protocols, and storage solutions, this project aims to balance cost-efficiency with reliability and performance. The research evaluates …

Design, Simulation, And Testing Of Planar Transformer For Smart Green Power Node (Sgpn) Isolation Using Ansys, Brooke Scott

Electrical Engineering and Computer Science Undergraduate Honors Theses

The goal of this project was to design and simulate a small, high-frequency, planar, ferrite-core transformer which can be used in a variety of applications, the most relevant of which is photovoltaic (PV) converter systems, which often require bulky transformers to function properly. The current research involved several processes: (1) Understanding and designing a tutorial for the use of Ansys software to aid in the efficient development and modeling of transformers, (2) designing and simulating a planar transformer in Ansys to be used in a solar converter, specifically the Smart Green Power Node (SGPN), and (3) testing the planar transformer …

Emerging Applications On Reconfigurable Computing Platforms, Zhenyu Xu

All Dissertations

Security and high-performance computing have become two of the most critical demands in modern technology. The increasing complexity of digital systems, the need for real-time processing, and the emergence of sophisticated cyber threats require computing solutions that balance computational power with adaptability and security. Reconfigurable computing platforms, particularly Field-Programmable Gate Arrays (FPGAs), offer a promising solution to these challenges by combining flexibility with hardware acceleration. Many new applications have emerged with the developing of reconfigurable platforms.

FPGAs can be utilized in two primary directions: as control and high-precision measurement units for security-sensitive applications, and as accelerators capable of outperforming GPUs …

Design Of A Novel Low-Cost Hybrid V-Shape Spoke-Type Ferrite Ipm-Synrm For Ev Traction Using Fem Software, Kenghao Cai

Master's Theses

This paper presents a hybrid V-shape spoke type ferrite Interior Permanent Magnet Synchronous Reluctance Machine (PMA-SynRM) for electric vehicle traction application. Ferrite or ceramic IPM-SynRMs compared to Neodymium (NdFeB) based IPM-SynRMs typically have lower torque, power density, and efficiency overall. Motivated by rising costs and international policies making it increasingly more challenging to obtain rare-earth metals, alternatives should be explored. With the help of finite element method (FEM) software, Ansys Maxwell, this study probes into a novel three-phase ferrite-only hybrid Spoke-type V-shaped IPM-SynRM using Tesla Model 3's neodymium powered V-shape interior permanent magnet machine as a benchmark. The proposed motor …

Towards Mitigation Of The Light Network Load Performance Penalty Of The Network Link Outlier Factor (Nlof), Jaime Merin Guzman

Open Access Theses & Dissertations

Detecting and localizing faults in communication networks is critical to maintaining reliable and efficient network operations. The Network Link Outlier Factor with Most Likely Link (NLOF: MLL) algorithm has demonstrated its potential to automate this task but suffers from significant performance degradation under low network load conditions, where limited network flow data reduces its ability to localize faults. This thesis proposes and evaluates the performance of a synthetic traffic generation algorithm to be used with NLOF:MLL. This algorithm strategically injects synthetic flows that supplement the insufficient real network flows, thereby improving NLOF:MLL's performance under low-load conditions. Specifically, we select network …

Hybrid Dc-Dc Converters For Soft Charging Capacitive Actuators: Modeling, Analysis And Design, Bahlakoana Mabetha

Dartmouth College Ph.D Dissertations

Recent trends in haptics, microrobotics and ultrasound technology have shown an increasing use of piezoelectric and other electrostatic actuators. These actuators are suited for miniaturized applications due to their high power density and favorable scalability at a small size. Their electrical impedance at lower frequency (their typical operating range) is capacitive, therefore, they can be modeled as capacitive loads.

The driving circuits for capacitive actuators need to deliver and recover (bidirectional) dominantly reactive power, unlike typical power electronics converters for resistive loads which deliver (unidirectional) real power to the load. Therefore, the circuits, operation, and optimization required to drive these …

Finding Groundwater With Electricity: Research And Testing Of An Electro-Resistive Ground-Surveying Device For Use In Well-Drilling Applications, Samuel L. Heath

Senior Honors Theses

A custom-built electro-resistive water detection device is tested under various conditions to evaluate its overall performance and sensitivity to changing variables. The tests, designed to assess accuracy and precision, revealed that the prototype exhibits high reliability (~ 99%) for both Schlumberger and Wenner arrays across different electrode spacings and soil conditions. Moreover, the measured resistivity values from the soil tests aligned with established literature ranges for each soil type. The device also showed the ability to consistently detect changes in soil water content by producing measurable variations in resistivity. At a total cost of $181, this prototype can serve as …

Validating An Electronics Cooler Experiment And Optimizing Its Performance Using Ansys Icepak, Daniel V. Curl

Mechanical Engineering Undergraduate Honors Theses

Researchers at the University of Arkansas' Mechanical and Electrical Engineering Research Departments have designed and built a cold plate and substrate design for a 10 kV SiC MOSFET power module. Many variables define the design of the cold plate and substrate system and have quantifiable effects on the device’s performance. These variables include but are not limited to geometry and material selection of the fins and substrate. Manufacturing many test designs, running experiments, and comparing their performance is a time-consuming and expensive design optimization method that may be effective for some low-cost applications. Still, simulation is often a more cost-effective …

Generative Ai For 3d Printed Antenna Design, Jennifer Ann Chavez

Open Access Theses & Dissertations

This research explores the integration of generative artificial intelligence (AI) with a physics-informed particle swarm optimizer (PSO) to develop 3D printable microstrip patch antennas. A neural network was trained on a dataset of microstrip patch antenna geometries and their corresponding performance metrics: return loss and gain. The PSO used a fitness function prioritizing low return loss in potential antennas, eventually yielding novel antenna geometries with parasitic components. 3D printing constraints were also hard coded into the framework, thus preventing any geometries being generated that cannot be fabricated. When simulated using Ansys HFSS, the AI generated microstrip patch antennas exceeded the …

Inference Per Joule: A Performance Metric For Artificial Intelligence In Space Applications, Eduardo Macias Zugasti

Open Access Theses & Dissertations

The use of artificial intelligence (AI) has grown exponentially in recent years. This growth is driven in part by the significant advancements in computing capabilities, which have also increased exponentially. Computers have not only become more powerful but also smaller in size, thanks to the evolution of transistor technology. These developments have enabled AI to become a widely accessible tool, even in recreational activities such as image creation and entertainment videos.

More recently, the use of AI has extended to space applications, where it can enhance and optimize various tasks. However, space conditions pose significant challenges for conventional computers due …

Development Of A Portable Electroencephalogram With Display, Seth D. Davis

Electronic Theses and Dissertations

In this experiment, the goal was to design, build, and test an Electroencephalogram (EEG) circuit that would then be paired with a touchscreen display as a portable unit for use in Schizophrenic research at East Tennessee State University at the Quillen College of Medicine. The requirements for this prototype denoted that the device had to be able to obtain a signal from two electrodes placed on the head of an individual with a third attached to the ankle as a ground, amplify and filter the signal, and display the results on a touchscreen display for recording and analyzing. The circuit …

Using Rf Hardware Technologies To Counteract Interference Within Dsrc Caused By Adjacent Unlicensed Bands, Grayson Hatcher, Billy Kihei, Nathan Kirkwood, Marco Tello

Symposium of Student Scholars

In recent years, competition within Radio Frequency (RF) communication bands has led to an overlap between the U-NII-4 band used by low-cost consumer devices, and the Dedicated Short Communication Band (DSRC) used by the Georgia Department of Transportation. Past research con- firmed that this interference leads to drastic reduction in Packet Reception Rate (PRR) for Roadside Units (RSUs) and On- Board Units (OBUs) throughout the country, resulting in a reduction of stability between different components of the Intelligent Transportation System (ITS). Our research team set a goal to prove that a low-cost and simple modification can be made to RSUs …

Static Characteristics Of An Electromagnetic Three-Phase Reactive Power Sensor For Converting Asymmetric Currents, Timur Urunbayevich Kurbaniyazov

Chemical Technology, Control and Management

This article discusses the processes in the elements and structures of three-phase electromagnetic current sensors used in measuring and controlling three-phase asymmetric reactive power in power supply systems, research models of quantities and parameters, physical mechanisms, and mathematical formulas based on graphical models.

Investigation Of The Electrical Capacitance Tomography System For Determining The Spatial Distribution Of Moisture In Grain Storage, Shamte J. Kawambwa

Tanzania Journal of Engineering and Technology (TJET)

Excessive moisture content (MC) in stored grains promotes the growth of fungi and molds, which affects the quality of the grains. Effective grain monitoring methods are essential for detecting and managing grain spoilage. Electromagnetic imaging (EMI) techniques provide a promising alternative to traditional techniques by visualizing the spatial distribution of moisture within grains rather than merely average MC values offered by traditional techniques. However, existing EMI approaches often use hard-field waves, which are expensive and fragile. This study introduces an Electrical Capacitance Tomography (ECT) system that employs soft-field waves to monitor the moisture content of the grains. The system was …

Synthetic Inertia Provision For Load Frequency Control In Networks With High Penetration Of Renewable Energy Sources, Paulina Mkoi

Tanzania Journal of Engineering and Technology (TJET)

The integration of renewable energy sources (RESs) such as solar photovoltaic (PV) and wind energy has become a promising solution as the world shifts toward clean energy. Solar PV and wind resources are increasingly replacing conventional synchronous generators, leading to reduced system inertia and increased vulnerability to frequency instability during disturbances. To address this challenge, this study proposes a novel synthetic inertia provision strategy using a battery energy storage system (BESS) integrated alongside solar PV. The proposed method dynamically compensates for the loss of inertia by considering the variability of solar PV output due to changes in irradiance and temperature. …

Clustering Mini-Grids To Enhance Power Systems Reliability In Distributed Generation, Santos Kihwele

Tanzania Journal of Engineering and Technology (TJET)

This study investigates the effectiveness of clustering mini-grids as a method to improve the reliability and operational stability of distributed generation systems in remote areas, particularly where renewable energy sources are predominant. As renewable resources like solar and wind are increasingly integrated into mini-grids, these systems face various challenges, particularly in maintaining stable voltage and frequency across interconnected networks. Such issues are compounded by the intermittent nature of renewable energy sources and the lack of extensive communication infrastructure in rural or resource-constrained settings. To address these control challenges, this study applies droop control techniques to two mini-grids in Uganda, utilizing …

Power-Beaming: Wireless Energy Transfer Using Lasers, Spencer L. Barnett

ATU Scholars Symposium

The objective of the project is to implement a wireless energy transfer system utilizing laser technology. This system involves modulating the laser’s beam profile and spatial distribution through precise optical manipulation. The energy transmitted by the laser is captured by a photovoltaic array, commonly referred to as a solar panel, which is engineered to convert incident photons into direct current (DC) electrical power. The current challenge is to develop a reliable wireless energy transfer mechanism capable of operating over extended distances, thereby overcoming the constraints imposed by wired connections, particularly in environments where wiring is impractical, such as in space. …

Semi-Autonomous Trash Bot, Ben Leon, Ethan Mashburn, Connor Olivera, Dillon Michael Wood

ATU Scholars Symposium

Title: Semi-Autonomous Trash Robot

Authors: Benjamin Leon, Ethan Mashburn, Connor Olivera, Dillon Wood

Abstract: Environmental pollution is becoming more worrying every day as megatons of human waste persist in vast amounts in our ecosystems. The existing waste collection methodologies, with the labor, time, and cost components combined, make the process cumbersome. A potential solution could be an automated waste collection robot that incorporates AI into a cheap system that autonomously detects trash. This report proposes a machine that may be manufactured to adequate standards in terms of size and cost and deployed in various environments, with the ultimate goal of …

A Dynamically Efficient Predictive Controller For Voltage Stability In A Dc To Dc Boost Converter, Giovanni Reyna

Electrical and Computer Engineering ETDs

Reliable voltage regulation has become a critical issue with increase demand in modern power electronic applications. This study presents a Model Predictive Controller (MPC) for voltage regulation in DC-to-DC boost converters. A closed loop analytical MPC framework is created with the purpose of computing optimal duty cycles to maintain a stable output voltage under varying load conditions, input changes, and disturbances.

To evaluate the performance of the MPC we set the controller against a comparative analyzing with a traditional cascading proportional integral (PI) controller. The proposed controller design is specifically targeted to improve dynamic efficiency during the converter’s transient events. …

Utilizing Machine Learning To Predict The Charge Storage Capability Of Lithium-Ion Battery Materials, Manoj Chhetri, Karen S. Martirosyan

Physics & Astronomy Faculty Publications

With the increasing demand for high-performance batteries in applications such as electric vehicles and portable electronics, accurately predicting the charge storage capacity of battery materials is crucial for developing more efficient and reliable energy storage systems. Machine Learning (ML) and data-driven approaches, plays a vital role in enhancing our understanding of Li-ion battery performance, guiding materials design, optimizing system efficiency, and accelerating innovation in energy storage technologies. In this study, an ML-based approach was applied to a dataset of 2345 rechargeable Li-ion battery materials, obtained from the Materials Project online portal, to predict gravimetric charge storage capacity ─ a key …

Design And Characterization Of Radiation-Hardened Gaas Hbt-Based Optical Transceivers, Collin Burt

Electrical and Computer Engineering ETDs

Optical transceivers are desirable for their galvanic isolation and natural immunity to electromagnetic interference compared with direct electrical connections. This is true in normal operating environments as well as radiation environments. This work realizes and characterizes GaAs HBT-based optical transceivers across temperature and a range of radiation environments including high dose rate, total ionizing dose, neutron, and heavy ion. The transceiver designs are discussed and specific environmental design considerations are highlighted. Final results for each environment are provided and compared with existing transceivers.

Swvl: A Custom Ai-Powered Face Tracking Camera Gimbal, Alexander J. Anderson-Mcleod, Jakub Jerzmanowski, Michael Laitarovsky, Trevor Allison, Jagger Tanner

Senior Theses

In response to the growing demand for smarter, more responsive face tracking cameras in the post-pandemic world, our team designed SWVL, a custom AI-powered face tracking gimbal meant to address the limitations commonly encountered by the commercial models currently on the market. These commercially available gimbals come with several issues, such as frequently losing track of the person in the frame and requiring manual resets, which we sought to fix with our implementation. We designed a system with fully custom hardware and software including a 3D printed dual-axis camera gimbal driven by stepper motors, a control PCB based around an …

Developing Fixed-Bias Langmuir Probes For Multi-Point Constellation Deployments, Henry Carter Valentine

Doctoral Dissertations and Master's Theses

Since their initial development in the early 20th century, electrostatic Langmuir probes have proved invaluable in terrestrial and interplanetary ionospheric sounding applications. When deployed aboard rocket and satellite platforms, these probes yield high-cadence, in-situ measurements of key plasma parameters such as electron density, ion density, and electron temperature. Furthermore, the efficacy of Langmuir probes in characterizing the three-dimensional structure and dynamics of ionospheric plasmas can be augmented by the technique of multi-payload deployments. In this work, we discuss the design, development, and analysis of fixed-bias Langmuir probes constructed for two multi-point science campaigns: the Mars-bound, dual-satellite Escape and Plasma Acceleration …

A 0.18 Μm Cmos 40 Ghz Miniaturized Coupled-Line Coupler With Enhanced Directivity, Elsayed Ibrahim Elsaidy, Amr H. Hussein Prof.Dr., Mustafa M. Abd Elnaby Prof. Dr., Anwer S. Abd El-Hameed Dr.

Journal of Engineering Research

No abstract provided.

Design And Development Of A Low-Cost Educational Robot: A Scalable And Affordable Software Learning Platform, Diana Refaat Henry Jacob, Mohamed Tarek Elawa, Ashraf Mohamed Hafez

Journal of Engineering Research

This study presents the design and development of a low-cost educational robot to enhance learning experiences in robotics and programming. The system integrates robust software development, ensuring seamless interaction between sensors, actuators, and a custom-designed graphical user interface (GUI). The robot is equipped with various sensors and actuators to support a broad range of experiments and educational applications. The software architecture is detailed, focusing on its modularity and ease of use, enabling students to intuitively program and interact with the robot. Additionally, a series of experiments were conducted to evaluate the performance of the sensors and actuators, providing insights into …

Non-Orthogonal Multiple Access Empowered Physical Layer Security Systems: Review, Issues And Challenges, Aml Fawzy, Mahmoud Selim, Maha Elsabrouty, Sameh Napoleon, Mustafa M. Abd Elnaby

Journal of Engineering Research

As 5G networks advance, the demand for higher data rates, enhanced spectral efficiency, and increased connectivity intensify. Non-orthogonal multiple Access (NOMA) addresses these needs by allowing multiple users to share the same time and frequency resources, thus optimizing network resource utilization and significantly boosting system capacity and throughput. NOMA's influence extends beyond traditional communication scenarios, impacting various vertical industries that require extensive connectivity, such as the Internet of Things (IoT). This transformative approach is crucial for industrial and critical mission applications. Given the importance of safeguarding these communications from potential eavesdroppers, Physical Layer Security (PLS) emerges as a vital tool. …

Multi-Channel Features Combined With Gray Features For Remote Sensing Image Classification, Khaled Hasan, Hussien Harb, Lamiaa A. Elrefaei, Hala M. Abdel-Kader

Mansoura Engineering Journal

Image classification in remote sensing is crucial for various applications like deforestation monitoring and Land Use/Land Cover (LULC) mapping. While grayscale images offer simplicity, recent advancements have enhanced classification by integrating spatial and relative data. However, relying solely on grayscale images overlooks valuable color information from different channels. To overcome this, researchers have explored two strategies: combining diverse features and utilizing multi-channel features. These methods merge spatial information and exploit shared features across channels. Despite their improved performance compared to grayscale, they face increased dimensionality, necessitating dimensionality reduction techniques. In our study, we propose a novel approach that integrates spatial …

Performance Of Neural Networks On Fpga For Embedded Devices Using Hls4ml Framework, Alam N. Romo Lopez

Master's Theses

As machine learning models such as neural networks are investigated for their applications across many fields, the demand for models that can be implemented on an embedded device grows. Field Programmable Gate Arrays (FPGAs) have become an attractive option for implementing these models in hardware. This thesis considers the viability of FPGA implementations for machine learning on low-resourced embedded systems. The hls4ml project is a promising prospect for machine learning on FPGA devices. To test hls4ml, we used a model trained on the MNIST digits dataset, which was then synthesized for the PYNQ-Z2 device. We fine tuned the performance by …

Misalignment Uncertainty In Near-Field Thz Scattering Experiments, Philip Patterson

Theses and Dissertations

This research investigates the effect of misalignment on the near-field scattering of cylinders in the 550-700 GHz frequency band. A Type-1 calibration is performed on previously collected data, using a near-field physical optics solution to simulate scattering at various positions and orientations. The alignment of the cylinders at the time of measurement is predicted by comparing the range profiles of the theoretical and calibrated responses. The data with the most similar range profiles had a mean calibration difference metric of -2.78 dB and a standard deviation of -0.57 dB, demonstrating the presence of sources of error that are dominant over …