Electrical and Electronics Commons^™

Conversion Of Heat Energy From Cooling Water Of Diesel Engine To Electrical Energy Using Thermoelectric Generator, Muhammad Hasan Albana

Makara Journal of Technology

This research objective is to convert heat from the radiator fluid of a diesel engine to electrical energy by utilizing a thermoelectric generator (TEG). The TEG consists of 20 semiconductors (TE modules) and is equipped with a heat sink. The research shows that using the TEG, the heat of radiator fluid can be converted to electrical energy, although the electricity generated is small. The maximum electrical voltage generated by the TEG when modules were connected in series was 10 volts. When the TE modules were connected in parallel and series-parallel, the maximum voltages generated were 2.11 and 2.53 volts, respectively. …

Immittance Response On Carboxymethyl Cellulose Blend With Polyvinyl Alcohol- Doped Ammonium Bromide-Based Biopolymer Electrolyte, Norfatihah Mazuki, Yuki Nagao, Ahmad Salihin Samsudin

Makara Journal of Technology

The blended carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVA) doped with various compositions of ammonium bromide (NH4Br)-based solid biopolymer electrolytes (SBEs) were prepared by using the casting method. In this present work, CMC/PVA–NH4Br SBE thin film was used to investigate the electrical conductivity via electrical impedance spectroscopy. The maximum conductivity obtained was 3.21 X 10−4 S cm−1 for sample AB20 at ambient temperature (303 K), and this result might be due to the increased number of charge carrier. A dielectric study was conducted to understand the conductivity behavior. The electrical properties have been measured as a function of frequency of …

Transition Metal Dichalcogenide For High-Performance Electrode Of Supercapacitor, Saifful Kamaluddin Muzakir, Ahmad Salihin Samsudin, Bouchta Sahraoui

Makara Journal of Technology

Molybdenum dichalcogenides have been reviewed from the perspectives of bandgap, conductivity, and oxidation states of transition metal. Researchers have concluded that a narrow-bandgap transition metal dichalcogenide with high conductivity could be achieved for the high-performance electrode of a supercapacitor.

The Importance Of Usability Aspect In M-Commerce Application For Satisfaction And Continuance Intention, Yassierli Yassierli, Vinsensius Vinsensius, M. S. Syed Mohamed

Makara Journal of Technology

There has been a rapid growing of m-commerce application in recent years due to the development of mobile communication technology and e-commerce business. However, only about 30% of online users, who conduct online searching, make online purchases. The low conversion rate seems to be correlated with poor usability aspect of most m-commerce applications and poor satisfaction reported by users. Research has reported that satisfaction and continuance intention in using m-commerce applications have relationships with service quality and information quality. In this study, a new model of user satisfaction and continuance intention in the context of mobile application was proposed by …

A 2.3/3.3-Ghz Dual Band Low Noise Amplifier Using Switchable Load Inductor In 0.18-Um Cmos Technology, Taufiq Alif Kurniawan, Hsiao-Chin Chen

Makara Journal of Technology

In this paper, the dual band low noise amplifier is designed in 0.18-μm CMOS technology. By combining the proposed switchable load inductor for gain controlling and the conventional inductive source degeneration topology, narrow band gain and good impedance matching are achieved at 2.3/3.3-GHz frequency bands. The new mathematical analysis of low noise amplifier design is derived to define the component parameters of the proposed circuits. The proposed low noise amplifier exhibits gain of 17.18 dB and 15.5 dB, and noise figure of 2.67 dB and 2.52 dB at the two frequency bands, respectively.

Automated Compilation Test System For Embedded System, Mohamad Khairi Ishak, Ooi Jun Hwan, Teh Jiashen, Nor Ashidi Mat Isa

Makara Journal of Technology

Embedded system testing involves testing an integration of software and hardware. It is increasingly difficult to evaluate the functionality of each module within a short time because of the increasing number of tests required. In this paper, a novel stepwise methodology involving the use of an automated compilation test system (ACTS) is proposed, to improve the quality of testing and optimize the testing time using automation. Using the proposed method, the testing coverage can be maximized, while minimizing the manual work and testing time required. This ACTS was used to automate the test code compilation and execution for different hardware …

Activated Carbon Fixed-Bed Adsorber Design For Treating Chromium Hexavalent Wastewater, Tedi Hudaya, Velicia Rachmat

Makara Journal of Technology

Pollution caused by industrial wastewater containing heavy metals is a major issue, primarily due to its toxic nature. A cheap yet effective method to deal with such wastewater is activated carbon adsorption. The purpose of this research is to evaluate and design a fixed bed adsorber with granular activated carbon as an adsorbent to process wastewater-containing chromium hexavalent (Cr 6+). Experiments show that the Langmuir isotherm fits the equilibrium data as effectively as the Freundlich isotherm. Activated carbon used in this research is Jacobi 2000® derived from bituminous coal. The lab scale inlet volumetric flow is 100 mL/h with different …

Development Of A Rapid Fatigue Life Testing Method For Reliability Assessment Of Flip-Chip Solder Interconnects, Cody Jackson Marbut

Graduate Theses and Dissertations

The underlying physics of failure are critical in assessing the long term reliability of power packages in their intended field applications, yet traditional reliability determination methods are largely inadequate when considering thermomechanical failures. With current reliability determination methods, long test durations, high costs, and a conglomerate of concurrent reliability degrading threat factors make effective understanding of device reliability difficult and expensive. In this work, an alternative reliability testing apparatus and associated protocol was developed to address these concerns; targeting rapid testing times with minimal cost while preserving fatigue life prediction accuracy. Two test stands were fabricated to evaluate device reliability …

Distance-Based Cluster Head Election For Mobile Sensing, Ruairí De Fréin, Liam O'Farrell

Conference papers

Energy-efficient, fair, stochastic leader-selection algorithms are designed for mobile sensing scenarios which adapt the sensing strategy depending on the mobile sensing topology. Methods for electing a cluster head are crucially important when optimizing the trade-off between the number of peer-to- peer interactions between mobiles and client-server interactions with a cloud-hosted application server. The battery-life of mobile devices is a crucial constraint facing application developers who are looking to use the convergence of mobile computing and cloud computing to perform environmental sensing. We exploit the mobile network topology, specifically the location of mobiles with respect to the gateway device, to stochastically …

Stability Analysis Of A High-Power Microgrid, David Manuel Carballo Rojas

Graduate Theses and Dissertations

The objective of this thesis is to perform the modeling and stability analysis of a high-power microgrid with multiple parallel-and grid connected voltage source converters using the system parameters from the high-power microgrid testbed at the National Center for Reliable Electric Power Transmission (NCREPT) at the University of Arkansas in order to identify, minimize, if not eliminate, the potential instabilities that can affect the proper operation of the microgrid testbed. To achieve this objective, the mathematical modeling of the high-power microgrid considering the adverse effects of resonances due to interactions among the converter LCL output filters is presented and analyzed. …

Nanosatellite Launch Data-Logger (Sync), Christopher Martin Gerdom

Master's Theses

CubeSat designers are increasingly looking to incorporate delicate structures and optics into their payloads. These delicate payloads, however, may not survive the required absolute-worst-case launch vibration testing needed for flight certification. To help address this problem, and to better match testing conditions to real-world launch environments, this thesis introduces Sync, a compact 1/4U CubeSat payload designed to collect data on the vibrations and thermal environments CubeSats experience inside a deployer on the way to orbit. This data can be used to better understand the launch environment for different vehicles, and help develop new, more realistic testing guidelines that could enable …

3d Signal Strength Mapping Of 2.4ghz Wifi Networks, Brett D. Glidden

Electrical Engineering

Many commercial businesses operate out of multi-story office buildings. These companies often use many Wi-Fi access points to set up their own wireless network. IT personnel determine proper Wi-Fi access point placement using Wi-Fi strength maps. Conventional Wi-Fi strength maps only provide a two-dimensional view representing the wireless access point's effective range. The signal quality and strength measurements do not include changing vertical elevation. Efficient network layout in a multi-story building requires a system calculating signal quality metrics in three dimensions.

This project involves designing and prototyping a system to achieve 2.4GHz Wi-Fi signal quality measurements in a three-dimensional reference …

A Novel Ultrasound Imaging Technique Using Random Signals, Anahita Khalilzadeh

Electrical Engineering Theses and Dissertations

Ultrasound imaging has been used extensively because of its benign nature and relatively low cost implementation. The most common approach for forming an image is Brightness Mode (B-Mode), which uses an array with dynamic focusing. Focus is performed through Phase Shifters that are bulky and complicated components which increases the device cost.

This research describes a new method to form an Ultrasound image, without relying on phase shifting. The proposed method offers a lower cost solution compared to the B-Mode systems and overcomes some of their inherent limitations.

Furnace System Improvements, Kenji K. Anzai, Ethan Fedor, Patrick Zailaa

Mechanical Engineering

This Final Design Review (FDR) documents the work done by the group to manufacture the system to deliver improvements to the furnace in the Cal Poly microfabrication laboratory (better known as the cleanroom). The document describes the material covered in the Scope of Work (SOW), including background research, customer needfinding, and the problem statement, material associated with concept development and selection for Preliminary Design Review (PDR), material detailing the design and manufacturing plan of the system for Critical Design Review (CDR), and new material detailing the manufacture of the system for FDR.

Research done for the SOW resulted in a …

A Computational Analysis Of The Gradient Concentration Profile Of Deet And The Mosquito Behavioral Response, Brandon Carver

Master's Theses

DEET is a common active ingredient in most spatial repellents. DEET is also a volatile organic compound. DEET prevents mosquitoes from detecting and coming into contact with an human individual. Gas sensing technologies such as metal oxide semiconductor sensors can detect VOCs. The World Health Organization provides the majority of efficacy testing methods. This research adapts methods from the WHO and use of MOS sensors to further understand how and why DEET affects mosquitos. A custom developed system is used to measure DEET dissipation and observe mosquito behavioral response to the DEET. DEET dissipations and mosquito behavior is measured within …

Dc-Dc 4-Switch Buck-Boost Converter For Energy Harvesting From Elliptical Machines, Alexander C. Samietz, Gustavo Guzman

Electrical Engineering

The senior project report documents the process of replacing the network of resistors inside an elliptical machine with a DC-DC buck-boost converter. The buck-boost DC-DC converter accepts a wide input range of 5-60 Volts, with an output of 36 Volts for the most efficient use of the already available microinverter. The microinverter reclaims the lost energy and safely distributes it back to the electrical grid. The addition of this project reduces heat emissions from wasted energy and shrinks the carbon footprint of its users.

Fully Analog Laser Driver With Robust Active Feedback Control, John Petrilli

Graduate Theses and Dissertations

The objective of this project was to go through a real life engineering development cycle, document and justify the design choices, and use background experience in electronic design and control systems to implement the best design possible. The laser driver implemented in this project is designed for the general use of a large variety of diodes in continuous wave mode, much like off the shelf laser drivers. The design goals included improving upon off the shelf laser drivers by decreasing steady state error, setting time, response time, and overshoot. Many different feedback control systems were evaluated, and a modified PID …

Review Of Recent Nuclear Magnetic Resonance Studies Of Ion Transport In Polymer Electrolytes, Stephen Munoz, Steven Greenbaum

Publications and Research

Current and future demands for increasing the energy density of batteries without sacrificing safety has led to intensive worldwide research on all solid state Li-based batteries. Given the physical limitations on inorganic ceramic or glassy solid electrolytes, development of polymer electrolytes continues to be a high priority. This brief review covers several recent alternative approaches to polymer electrolytes based solely on poly(ethyleneoxide) (PEO) and the use of nuclear magnetic resonance (NMR) to elucidate structure and ion transport properties in these materials.

Big Data And Sensor Network For Construction Material Testing, Yao Shi

Theses and Dissertations

Engineers and contractors need to have a precise understanding of the development progress of concrete strength in the natural environment, which helps to save project time and cost. However, current practice of concrete construction depends on published data, charts and curves from laboratory tests. The data would not show frequently changing environmental conditions in the real world, which can affect concrete quality significantly. The objective of this research is to design a reliable and accurate method to validate test data of the strength developments of concrete specimens in early stages. The approach includes the following tasks: (1) arrange sensors to …

Transcribing Braille Code: Learning Equations Across Platforms, Deegan Atha, Courtney Balogh

Purdue Journal of Service-Learning and International Engagement

Deegan Atha, a graduating senior in electrical engineering and a future engineer, is interested in human-centered design and developing technology that helps students engage and be successful in STEM.

Courtney Balogh, a junior in mechanical engineering, is interested in human-centered design and the importance it plays in product development. Deegan and Courtney are members of the Purdue EPICS project, Learning Equations Across Platforms (LEAP). They partnered with the Indiana School for the Blind and Visually Impaired (ISBVI) to develop a braille transcription device and web application that converts braille to print in real time.

Cost Benefit Analysis Of Led Vs Florescent Lighting, Kurtis Clark, Phillip Humphrey

Student Research

Over the last few years, the state of Oklahoma has been looking at ways to reduce expenses to address concerns about a budget deficit. There have been efforts made to reduce expenses due to the use of energy. It has been said, when the lights are on, work is getting done. Running lights is therefore the cost of doing business. Our research examines the question, “is there a way to provide better lighting while operating at a lower cost.” This research examines the current lighting at Southwestern State University, primarily fluorescent lighting (FL), and a cost benefit analysis of switching …

Evaluation Of Eu:Licaf For Neutron Detection Utilizing Sipms And Portable Electronics, Michael A. Ford, Buckley E. O'Day Iii, John W. Mcclory, Manish K. Sharma, Areg Danagoulian

Faculty Publications

With the increasing cost and decreasing availability of ³He, there have been many efforts to find alternative neutron detection materials. Lithium calcium aluminum fluoride (LiCAF) enriched to 95% ⁶Li doped with europium was evaluated here as a replacement material for ³He. Wafers 0.5 cm thick, consisting of LiCAF crystals in a rubberized matrix, were embedded with wavelength shifting fibers (WSF) and mated to silicon photo-multipliers (SiPMs) to measure the photon response in a flux of neutrons from a DD neutron generator. Excellent discrimination was realized between neutrons and gammas, and both pulse-height discrimination and pulse-shape analysis were …

Electrical Characteristics Of A Balloon-Borne Radiation Instrument, Elena Pradhan, Jared Fuchs

Von Braun Symposium Student Posters

No abstract provided.

Thermal And Mechanical Energy Harvesting Using Lead Sulfide Colloidal Quantum Dots, Taher Ghomian

LSU Doctoral Dissertations

The human body is an abundant source of energy in the form of heat and mechanical movement. The ability to harvest this energy can be useful for supplying low-consumption wearable and implantable devices. Thermoelectric materials are usually used to harvest human body heat for wearable devices; however, thermoelectric generators require temperature gradient across the device to perform appropriately. Since they need to attach to the heat source to absorb the heat, temperature equalization decreases their efficiencies. Moreover, the electrostatic energy harvester, working based on the variable capacitor structure, is the most compatible candidate for harvesting low-frequency-movement of the human body. …

Effect Of Wireless Communication Delay On Dc Microgrids Performance, Mahmoud Saleh, Yusef Esa, Ahmed Mohamed

Publications and Research

This paper investigates the effect of wireless communication technologies latency on the converters and the bus voltage of centrally communication based controlled DC microgrids (MGs) during islanding. A DC microgrid with its communication based control scheme was modeled to show the impact of latency. Simulation results show that the impact may be severe depending on the design, and the operational condition of the microgrid before latency occurs.

Improving A Transient Stability Control Scheme With Wide-Area Synchrophasors And The Microwecc, A Reduced-Order Model Of The Western Interconnect, Robin Hallett

Graduate Theses & Non-Theses

This thesis is composed of two research projects. The first project investigated the feasibility of improving a generator tripping control scheme using wide-area synchrophasors and the second project focused on building a reduced-order model of the western North American power system (wNAPS) for use in a real-time digital simulator.

Transient stability is a major reliability issue for power systems. Radially-connected power plants are especially prone to transient stability problems. An example of this is the fourgenerator Colstrip power plant located in southeast Montana, USA. The Colstrip generators are protected by a tripping control system called the Acceleration Trend Relay (ATR) …

Impact Of Communication Latency On The Bus Voltage Of Centrally Controlled Dc Microgrid During Islanding, Mahmoud Saleh, Yusef Esa, Ahmed Mohamed

Publications and Research

Maintaining a sustainable and reliable source of energy to supply critical loads within a renewable energy based microgrid (MG) during blackouts is directly related to its bus voltage variations. For example, voltage variation might trigger protection devices and disconnect DERs within the MG. Centrally controlled MGs (CCMGs) type is dependent on communication. Therefore, it is very important to analyze the impact of communication networks performance degradation, such as latency, on the bus voltage of CCMGs. This paper investigates the effect of wireless communication technologies latency on the bus voltage and performance of centralized DC MGs. Two mathematical models were developed …

Using Gs/S Adc To Evaluate The Emi Of Gan-Based Power Devices, Chi Zhang

Electrical Engineering Theses and Dissertations

As the silicon-based power devices are gradually reaching their performance limits, new power transistors such as Silicon Carbide (SiC) and Gallium Nitride (GaN) FETs have been rapidly developed in recent years. GaN devices have been widely accepted by researchers for its higher speed and efficiency than silicon power devices. However, despite all its merits, the GaN device faces a more severe problem of electromagnetic interference (EMI) than the silicon device due to its high performance. Various control techniques of EMI have been studied so far and many of them require the evaluation of EMI. Research shows that the EMI level …

Investigating The Effect Of Detecting And Mitigating A Ring Oscillator-Based Hardware Trojan, Lakshmi Ramakrishnan

Electrical Engineering Theses and Dissertations

The outsourcing of the manufacturing process of integrated circuits to fabrications plants all over the world has exposed these chips to several security threats, especially at the hardware level. There have been instances of malicious circuitry, such as backdoors, being added to circuits without the knowledge of the chip designers or vendors. Such threats could be immensely powerful and dangerous against confidentiality, among other vulnerabilities.

Defense mechanisms against such attacks have been probed and defense techniques have been developed. But with the passage of time, attack techniques have improved immensely as well. From directly observing the inputs or outputs, adversaries …

Ku-Band Ag Channel Modeling, Albert Smith

Theses and Dissertations

With the rise in use of Unmanned Aerial Systems (UAS), there is a need for safe and reliable integration into existing infrastructure. A proposed system for beyond line of sight control links for UAS is a Ku-band air-to-satellite communication system. To ensure this proposed system does not interfere with existing terrestrial infrastructure that operates in the Ku band, an examination of the Ku-band air-to-ground channel is required. The focus of this thesis is the modeling of the Ku-band AG channel. Tests consisting of transmitting a single tone continuous wave signal were conducted with a signal generator onboard NASA’s Viking S-3 …