Structural Engineering Commons^™

A New Method For Simulating Power Flow Density Focused By A Silicon Lens Antenna Irradiated With Linearly Polarized Thz Wave, Catur Apriono, Eko Tjipto Rahardjo, Norihisa Hiromoto

Makara Journal of Technology

A terahertz system uses dielectric lens antennas for focusing and collimating beams of terahertz wave radiation. Linearly polarized terahertz wave radiation has been widely applied in the terahertz system. Therefore, an accurate method for analyzing the power flow density in the dielectric lens antenna irradiated with the linearly polarized terahertz wave radiation is important to design the terahertz systems. In optics, ray-tracing method has been used to calculate the power flow density by a number density of rays. In this study, we propose a method of ray-tracing combined with Fresnel’s transmission, including transmittance and polarization of the terahertz wave radiation …

High Temperature Corrosion Of Aluminized Aisi 4130 Steel With The Different Composition Of Nacl/Na2so4 Deposits, Mohammad Badaruddin, Chaur Jeng Wang, Yudhistyra Saputra, Abu Khalid Rivai

Makara Journal of Technology

The high temperature corrosion of AISI 4130 steel can be increased by hot-dip aluminizing coating. The aluminized steel specimens with the deposit composition of 100/0, 30/70, 50/50, 70/30, and 0/100 (wt.%) NaCl/Na2SO4 were oxidized at 750 °C for 1-49 h periods. According to a parabolic rate constant (kp) value, the aluminized steel with deposit composition of 70/30 NaCl/Na2SO4 shows the highest kp value (3.71 × 10-11 g2cm- 4s-1), later followed by the kp value of 3.35 × 10-11 g2cm-4s-1 for 100/0 and the lowest kp value is 7.731 × 10-12 g2cm-4s-1 for 0/100. Whereas, the kp value for the aluminized …

Effects Of Supplier-Manufacturer Relationships On Supply-Chain Performance Of Manufacturing Industries In Indonesia, Rachmad Hidayat, Khisbullah Hudha, Sabarudin Akhmad

Makara Journal of Technology

The present study describes the relationships between commitment, communication, satisfaction, trust, relationship quality with suppliers, and supply-chain performance. The population of the study was manufacturing companies in Indonesia. Respondents were the chief executive officers or corporate secretaries or the designated managers involved in strategic decision making. Samples were taken by using a proportional area random sampling technique. Structural Equation Modeling (SEM) was used for analysis. Results of both direct and indirect testing of hypothesis indicated two hypotheses of positive and significant effects and nine hypotheses of positive but insignificant effects. Those hypotheses of positive and significant effects were the direct …

Stochastic Optimization Of Supply Chain Risk Measures –A Methodology For Improving Supply Security Of Subsidized Fuel Oil In Indonesia, Adinda Yuanita, Andi Noorsaman Sommeng, Anondho Wijonarko

Makara Journal of Technology

Monte Carlo simulation-based methods for stochastic optimization of risk measures is required to solve complex problems in supply security of subsidized fuel oil in Indonesia. In order to overcome constraints in distribution of subsidized fuel in Indonesia, which has the fourth largest population in the world—more than 250,000,000 people with 66.5% of productive population, and has more than 17,000 islands with its population centered around the nation's capital only—it is necessary to have a measurable and integrated risk analysis with monitoring system for the purpose of supply security of subsidized fuel. In consideration of this complex issue, uncertainty and probability …

Transmission Electron Microscopy Characterization Of High-Temperatur Oxidation Of Fe-20cr-5al Alloy Prepared By Focused Ion Beam Technique, Mohammad Dani, Pudji Untoro, Teguh Yulius Surya Panca Putra, Parikin Parikin, Joachim Mayer, Arbi Dimyati

Makara Journal of Technology

The Focused Ion Beam (FIB) technique was applied for cross section preparation of the oxidized alloy for Transmission Electron Microscopy (TEM) study. Prior to preparation, the specimens of Fe-20Cr-5Al alloy sheet were oxidized in air at 1200 oC for 2 minutes, 10 minutes, 2 hours, and 100 hours. The microstructure and elemental composition of the samples were characterized using TEM equipped with an Energy Dispersive X-Ray Spectroscopy (EDX). The Electron Energy Loss Spectroscopy (EELS) was used to determine of the light elements. The TEM investigation reveals remarkable microstructure evolution of the specimens during oxidation which generally exhibit a typical multi-layer …

Strain Distribution And Crack Detection In Concrete Overlays With Pulse Pre-Pump Brillouin Optical Time Domain Analysis, Yi Bao, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This report is focused on the measurement of strain distributions and crack detection in unbonded and bonded pavement overlays. The main objectives of this study are: (a) to characterize the strain sensing properties of distributed fiber optic sensors with recently developed pulse pre-pump Brillouin optical time domain analysis (PPP-BOTDA), (b) to develop an installation method for real world applications, (c) to document the performance of the PPP-BOTDA technology in unbonded/bonded pavement applications, and (d) to develop a numerical model to facilitate the analysis of mechanical behavior of unbonded pavement overlay under vehicle wheel loads. A thin concrete layer can be …

Thermal Energy Storage In Building Integrated Thermal Systems: A Review. Part 2. Integration As Passive System, Dervilla Niall, Sarah Mccormack, Philip Griffiths, Luisa Cabeza, Lidia Navarro, Albert Castell, Alvaro De Grazia, Maria Brown

Articles

Energy consumption trends in residential and commercial buildings show a significant increase in recent decades. One of the key points for reducing energy consumption in buildings is to decrease the energy demand. Buildings envelopes are not just a structure they also provide protection from outdoor weather conditions always taking into account the local climate. Thermal energy storage has been used and applied to the building structure by taking advantage of sensible heat storage of materials with high thermal mass. But in recent years, researchers have focused their studies on the implementation of latent heat storage materials that if well incorporated …

Advancing Seismic Simulation Of Cold-Formed Steel Framed Buildings, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The objective of this research is to create a computationally efficient seismic analysis framework for cold-formed steel (CFS) framed-buildings supported by hysteretic nonlinear models for CFS members and screw-fastened connections. Design of CFS structures subjected to lateral seismic forces traditionally relies on the strength of subassemblies subjected to lateral loading of systems, such as strapped/sheathed shear walls and diaphragms, to provide adequate protection against collapse. Enabling performance-based seismic design of CFS buildings requires computationally efficient and accurate modeling tools that predict the nonlinear cyclic behavior of CFS buildings, the individual CFS components and connections. Such models should capture the energy …

Bridge Seismic Retrofit Measures Considering Subduction Zone Earthquakes, Peter Dusicka, Ramiro Bazaez, Sarah Knoles

Civil and Environmental Engineering Faculty Publications and Presentations

Over the years, earthquakes have exposed the vulnerability of reinforced concrete structures under seismic loads. The recent occurrence of highly devastating earthquakes near instrumented regions, e.g. 2010 Maule, Chile and 2011 Tohoku, Japan, has demonstrated the catastrophic impact of such natural force upon reinforced concrete structures. Research was conducted to investigate the effect of subduction zone earthquakes on structural damage. The study suggests that large magnitude ground motions of long duration have the potential of significantly increasing the number of inelastic excursions and consequently incur more extensive structural damage as compared to ground motions with similar elastic spectral demands but …

Experimental Investigation Of Fiber Reinforced Concrete Beams, Karrar Ali Al-Lami

Dissertations and Theses

Shear strength of fiber reinforced concrete beams was studied in this research project. Three types of fibers were examined: hooked-end steel fiber, crimped-steel fiber, and crimped-monofilament polypropylene fibers. The experimental program included five beam specimens. Two of the beams were control specimens in which one was reinforced with minimum shear reinforcement according to ACI 318, while the other one did not have any shear reinforcement. Each one of the other three specimens was reinforced with one of the above mentioned fibers by 1% volumetric ratio. In addition to the beam specimens, three prisms were also made for each type fiber …

Interface Friction Parameters For The Mathematical Modeling Of Shell Structures With Infill, Alexander T. Bekker, Nikita Ya. Tsimbelman, Tatiana I. Chernova, Vadim D. Bruss, Ömer Bilgin

Civil and Environmental Engineering and Engineering Mechanics Faculty Publications

Thin metal or reinforced concrete shells with granular infill structures are considered in this article. These structures are massive and they are used as support for the construction of berthing quays, piers, artificial islands, shore protection, and other structures of coastal infrastructure. It is more convenient to use the thin shell structures during the development of the Arctic shelf, because it is possible to install them from the ice side. In addition, it is possible to enhance the technology and install thin shells with infill on deeper solid foundation layers. A mathematical model for the stresses on a compressible foundation …

Seismic Retrofit Benefit Considering Statewide Transportation Assessment, Selamawit Tesfayesus Mehary, Peter Dusicka

Civil and Environmental Engineering Faculty Publications and Presentations

The purpose of this study was to identify and demonstrate a methodology to prioritize bridges for retrofit in the State of Oregon. Given the limited resources available, retrofitting all vulnerable bridges in the foreseeable future would not be practical. Instead, a retrofit strategy needs to be developed to prioritize the inventory and enumerate the retrofit cost. In this study, a prioritization methodology used a holistic assessment of overall roadway system to consider highway route segments, rather than individual bridges. The overall assessment was based on a cost-benefit analysis including retrofit cost, expected economic loss (with or without retrofit) and social …

Power Maximization Of A Three-Phase Hydrokinetic Turbine, Matthew Carleson

Senior Theses

As Earth`s expendable resources dwindle, the need for alternative, renewable energy sources grows. Out of this need, an old favorite source is rising in popularity: small water turbines. Water-driven turbines first began as a means for turning mills and eventually evolved into massive dams that can power whole regions. This project focused on the construction of, and testing the properties of, a small pico-hydro power turbine. By using compressed air to drive the turbine, a representation of the peak power output was measured, serving as a basis for determining the value of pico-power systems in regards to the world`s current …

Behavior Of Reinforced Concrete Beams Retrofitted In Flexure Using Cfrp-Nsm Technique, Salam Al-Obaidi

Dissertations and Theses

A variety of retrofitting methods are used to upgrade existing structures. For example, steel plates and Fiber Reinforced Polymer (FRP) jackets are externally bonded to members to increase their capacity in flexure and shear. However, due to the issue of corrosion these strengthening systems may lose their efficiency with time. FRP materials have been used to strengthen many structural components of different shapes and types. FRP jackets, FRP Strips, and FRP rods have commonly been used to rehabilitate existing structural components. The many advantages of using FRP as strengthening materials have made this material an attractive alternative: advantages such as …

Alkali-Silica Reaction Mitigation Using High Volume Class C Fly Ash, Sydney Marie Dickson

Civil Engineering Undergraduate Honors Theses

Fly ash is the residue produced from coal combustion in electric generating plants. There are two types of fly ash, Class C and Class F. Approximately 40 percent of fly ash generated from coal combustion can be used as a partial replacement of cement in concrete. Incorporating fly ash improves concrete properties and extends its service life. Alkali-silica reaction (ASR) is an expansive reaction between reactive silica typically found in aggregates (rock and sand) and alkalis in cement. This reaction results in the formation of a gel that absorbs water and swells, which exerts an internal pressure in concrete. This …

Analyzing Stochastically Generated Material Properties For The Use In Mumerical Simulations Of Advanced Laboratory Tests Of Asphalt Concrete, Ken K. Rutabana

Civil Engineering Undergraduate Honors Theses

For such a large country as the US, adequate road transportation is a vital necessity that ensures the safety, prosperity, and development of the people. Covering 94% of the two million miles of paved roads and highways, asphalt concrete is essential to this country. This is one reason why it is crucial to understand the potential and limitations of asphalt concrete. Unfortunately, material testing is a costly and time consuming ordeal. Consequently, numerical modeling of asphalt testing using computer software has been successfully developed in the last decades. These models corroborate those obtained in the lab but are intended as …

Development Of Optimal Experimental Design Parameters For Pseudo Ambient Vibration Testing Of Bridges, David Samudio Castillo

Civil Engineering Undergraduate Honors Theses

The United States of America is facing an infrastructure crisis that is characterized by aging and deteriorating structures, a significant backlog of maintenance and upgrades for existing infrastructure, limited funding and lack of practical and effective tools for identifying and prioritizing the most pressing infrastructure needs. The American Association of Civil Engineers (ASCE) qualifies America’s infrastructure with a D+(ASCE Report Card). This rating reflects the general state of infrastructure that is unlikely to improve dramatically in the short-term, yet the situation costs the nation billions of dollars annually due to losses in economic efficiency and productivity, and in some cases …

A Study Of The Influence Of Particle Gradation In Bonded Assemblies, Matthew P. Watters

Civil Engineering Undergraduate Honors Theses

The discrete element method (DEM) has been used extensively to study soil, rock, and masonry behavior because of its ability to model the materials as individual particles or bonded clumps of particles. DEM allows for examination of the macro- and micro-scale response and provides a means to study the fundamental material behavior, but it is still considered computationally expensive in relation to other methods. To lower computational costs, the smallest particle sizes are often considered negligible and are left out of the model. Additionally, rock or intact materials are often modeled as a bonded assembly of uniform spheres. To date, …

Drive Plate Mass Polar Moment Of Inertia In Stokeo Type Resonant Column Devices, Michael Ryan Deschenes

Civil Engineering Undergraduate Honors Theses

The calibration procedure employed by researchers at the University of Arkansas (UA) to calibrate two Stokoe-type resonant column torsional shear (RCTS) devices is presented herein. Specifically, the development of a device-specific calibration process to determine the mass polar moment of inertia of the RCTS drive plate assemblies (J0), as a function of frequency, is described. Three aluminum calibration specimens and three stainless steel masses with known geometric and material properties were utilized to experimentally determine the J0 values. Experimental data collected by researchers at the University of Arkansas and obtained from other sources (Utah State University, the University of Texas …

Bulbous Pier: Alternative To Bridge Pier Extensions, Amilcar Chavez

UNLV Theses, Dissertations, Professional Papers, and Capstones

Bridge deck splashing causes deterioration to the bridge structure and renders the bridge unsafe for motorist and pedestrians. The traditional countermeasure for bridge deck splashing is pier extension, the pier extension moves the pier wave away from the bridge deck, but retrofitting existing bridges with pier extensions is costly. This research proposes the bulbous pier concept as an alternative to pier extension.

The decrease in the pier wave produced by the bulb is due to energy subtracted by the bulb via two forces, the viscous resistance, and the wave-making resistance. The proposed mathematical model for the bulbous pier design follows …

State Of Accelerated Bridge Construction (Abc) In The United States, Mike Ofili

Honors College Theses

The purpose of this project is to develop a toolkit for the design and construction of bridges using prefabricated materials primarily to reduce the closure time and on-site construction time of newly constructed bridges or bridges undergoing renovation. The research focuses specifically on short span bridges in Georgia (40,60,80, and 120ft spans).

Areas of primary concern for this project were design, constructability, structural analysis, the use of concrete and steel girders, cost efficiency, and industry surveys. In this particular portion of the study, the surveys proved to be most effective when combined with information obtained existing research as well as …

Load Bearing Clip Angle Design, Cheng Yu, Mohamad Yousof, Mahsa Mahavian

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The material contained herein has been developed by researchers based on their research findings. The material has also been reviewed by the American Iron and Steel Institute Committee on Specifications for the Design of Cold-Formed Steel Structural Members. The Committee acknowledges and is grateful for the contributions of such researchers. The material herein is for general information only. The information in it should not be used without first securing competent advice with respect to its suitability for any given application. The publication of the information is not intended as a representation or warranty on the part of the American Iron …

Load Bearing Clip Angle Design, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The report presents a comprehensive research project aimed at developing design methods for three limit states of cold-formed steel clip angles: shear, compression, and pull-over of the screw connections. For each limit state, a test program was conducted to investigate the behavior, strength, and deflection of the clip angles. The test results were compared with existing design methods for members similar to, but not exactly the same as, cold-formed steel clip angles. It was found that none of the existing methods worked well for the tested clip angles, therefore new design methods were developed for each of the three limit …

Senior Design: Proposed Stem Academic Building, Middlesex Community College, Senior Design Class

Civil Engineering Student Work

2015 Civil Engineering Senior Design Project.

A proposal for a new STEM building to be constructed on the Middlesex Community College.

Completed by:

• Abdullah Al Bakri
• Ryan Benoit
• Brittany Brown
• Michael Buraczynski
• Samuel Colangelo
• Joseph Connolly
• Kyle Elmy
• Michael Fischer
• Victor Goitia Jurado
• Michael Hanley
• Andrew Malian
• Michael Mathews
• Dionys Quezada
• Katie Rougeot
• Jacob Santos
• Isadora Sartor
• Vega Yerko

Phonon-Drag Contribution To Seebeck Coefficient Of Ge-On-Insulator Substrate Fabricated By Wafer Bonding Process, Veerappan Manimuthu, Shoma Yoshida, Yuhei Suzuki, Faiz Salleh, Mukannan Arivanandhan, Yoshinari Kamakura, Yasuhiro Hayakawa, Hiroya Ikeda

Makara Journal of Technology

In order to build high-sensitivity infrared photodetectors using SiGe nanowires, we investigate the thermoelectric characteristics of Ge-on-insulator (GOI) layers as a reference for SiGe. We fabricate p-type GOI substrates with an impurity concentration of 1016-1018cm-3 by a wafer-bonding process using Ge and oxidized Si wafers. Annealing treatment is performed in order to further increase the bonding strength of Ge/SiO2 interface. We measure the Seebeck coefficient in the temperature range of 290-350 K. The Seebeck coefficient of the GOI layers is very close to the theoretical value for Ge, calculated on the basis of carrier transport. Hence, there is a small …

Group Decisions In Value Management, Christiono Utomo, Farida Murti, Arazi Idrus

Makara Journal of Technology

This research deals with a technique to expedite group decision making during the selection of technical solutions for value management process. Selection of a solution from a set of alternatives is facilitated by evaluating using multicriteria decision making techniques. During the process, every possible solution is rated on criteria of function and cost. Function deals more with quality than with quantity, and cost can be calculated based on the theoretical time value of money. Decision-making techniques based on satisfying games are applied to determine the relative function and cost of solutions and hence their relative value. The functions were determined …

Fiber Optic Ring Resonator Sensor Detection Technique Based On Spectral Intensity Integration, Purnomo Sidi Priambodo, Sasono Rahardjo, Gunawan Witjaksono, Djoko Hartanto

Makara Journal of Technology

Resonant field phenomenon in optical ring resonator has been a major theme for various studies and can be used for various sensor applications. The spectral response shape changes are subjects to be discussed and analyzed for detection in optical sensor system. The spectral response changes are caused by various factors ranging from refractive index of the surrounding medium, medium loss due to absorption and scattering, and coupling variation between waveguides. These optical phenomena are mostly used for bio-sensor applications, since it is free from electromagnetic interference (EMI) and non-physically destructive. In this paper, we discuss our current research in developing …

Seebeck Coefficient Of Soi Layer Induced By Phonon Transport, Faiz Salleh, Takuro Oda, Yuhei Suzuki, Yoshinari Kamakura, Hiroya Ikeda

Makara Journal of Technology

The Seebeck coefficient of a patterned Si wire on P-doped SOI (Si-on-insulator) layer with a carrier concentration of 1018 cm-3 was measured near room temperature. The Seebeck coefficient is found to be smaller than that in the SOI layer and to be closer to the calculated Seebeck coefficient including the electronic contribution. The decrease in the Seebeck coefficient of Si wire is likely to occur due to the elimination of the contribution of phonon drag part. From the theoretical calculation of scattering rates by considering the scattering processes in phonon system, it is considered that an increase in phonon-boundary scattering …

Implications Of Heterogeneity In The Shock Wave Propagation Of Dynamically Shocked Materials, Jeffrey W. Lajeunesse

Master's Theses (2009 -)

The field of shock physics as a whole has only recently begun to pay particular attention to modeling heterogeneous materials under shock loading. These materials are important because of their practicality in terms of creating stronger, more shock resistant materials. To understand why they absorb shock impact energy better than homogeneous materials means that the small-scale processes that occur during the shock loading of these heterogeneous materials needs to be understood. Recent computational experiments, called mesoscale simulations, have shown that explicitly incorporating small-scale heterogeneous features into hydrocode simulations allows the bulk shock response of the heterogeneous material to be observed …

Hazard-Driven Drivers’ Behaviours Towards Vehicle-To-Median Safe Distances, Martha Leni Siregar

Makara Journal of Technology

A median is required for a two-way road to separate traffic from opposing lanes and to prevent head-on collisions. However, studies indicate that medians are also perceived as hazards which need to be avoided during driving. This hazard perception is manifested in drivers’ changing behavior towards various types of medians along the driving lanes inform of their tendency to allow various safe distances to the medians. The Indonesian Highway Capacity Manual (IHCM) does not differentiate between types of medians and the influence on the drivers’ choice of safe margin to the medians. Therefore, this study looks into how the existence …