Aerospace Engineering Commons^™

Fabrication Of Micropatterns On 3d Surfaces And Generation Of Linked Zno Nanowires, Hui Wang

Mechanical and Aerospace Engineering Dissertations - Archive

Conventional lithographic approaches are good at fabricating structures on the top surfaces of substrates. They are not suited for 3D surface patterning due to the fact that vertical radiation exposure is employed to transfer patterns. In the meanwhile, patterns generated on 3D surfaces, such as the vertical sidewalls of silicon channels and the irregular surfaces of glass micropipettes may provide valuable applications in microfluidics, 3D circuits, bioengineering and so on. In this work, we developed new approaches to produce metal micropatterns on the vertical sidewalls of silicon channels as well as to fabricate two separated metal microlines on the tips …

Development Of An Experimental And Analytical Model Of An Active Cooling Method For High-Power Three-Dimensional Integrated Circuit (3d-Ic) Utilizing A Multidimensional Configured Thermoelectric Modules, Huy Phan

Mechanical and Aerospace Engineering Dissertations - Archive

An increase in demand for more functionality and capacity of microelectronic components within the same logistic footprint drives the growth of three-dimensional integrated circuit (3D-IC) packaging technologies in recent years. However, the reduction in size and an increase in transistors density also intensified the heat flux of stacked-dice, which introduces many thermal challenges at both the package and cooling levels. Traditional passive cooling system such as forced air convection cooling, phase change materials and passive or active heat sinks will become inadequate to cool future processors and cannot accommodate the demand of future sub-ambient cooling of 3D-ICs. Within the past …

Hybrid Dynamic Simulation For Performance Optimization Of Legged Mechanisms, Daniel Montrallo Flickinger

Mechanical and Aerospace Engineering Dissertations - Archive

Agile locomotion is needed for mobile robots to efficiently navigate challenging terrain. The ability of an agile legged mobile robot to abruptly change trajectory allows it toquickly react to obstacles and successfully operate in environments usually more suited forlegged animals. The research presented herein aims to increase the agility and performanceof legged robots.Using hybrid dynamic simulation, novel methods are developed to model the inter-action of a legged robot with the ground. In considering robot agility, an accurate model ofthe events that occur while in contact is needed. Methods are developed to model groundinteraction where oblique angled impacts occur, and to …

Design And Modeling Techniques For Cooling Of Telecommunication Systems, Naveen Kannan

Mechanical and Aerospace Engineering Theses - Archive

Conventional data centers are extremely large buildings that have complex power distribution and cooling systems. These traditional brick and mortar data centers employ relatively expensive cooling systems and are inefficient. It has in turn led to an increase in construction and operational costs. These inefficiencies of traditional data centers can be overcome by partitioning the server load into modular sections which can be deployed, powered and cooled depending on availability and requirement. Furthermore, improvements in efficiency and operational costs can be achieved by employing "free cooling" to cool the IT equipment. Free cooling involves the introduction of outside air through …

Design Optimization Of A Wind Turbine Blade, Bharath Koratagere Srinivasa Raju

Mechanical and Aerospace Engineering Theses - Archive

This work focuses on designing a blade of 45 meters in length that produces a power of 1.6 MW. The design of the blade was done using the Blade Element Momentum theory and the Prandtl's tip loss factor was used. The aerodynamic loads and differential power at are tabulated and plotted.The finite element method for analysis of the blade is used. As the chord lengths vary decreasingly along the blade radii in order to use the simple beam theory the breath and height of the blade is considered as a function of the chord length, hence the analysis is done …

Filling Of Methane/Air Mixture In A Tube For Pulse Detonation Engines, Shravani Dwarakapally

Mechanical and Aerospace Engineering Theses - Archive

In pulse detonation engines, filling is a time consuming process; reducing these times will help to increase the frequency. The filling of a detonation tube, 1 m long tube with an internal diameter of 101.6 mm, closed at one end and opened at the other, was studied using the unsteady flow solver methane and air nominally at STP· Three cases were examined: (i) a 25.4 mm diameter port at the center of the closed end, (ii) nine ports of 25.4 mm diameter, one at the center of the closed end and eight distributed in two diametrically opposite rows, equally, four …

Control Of Airship Motion In The Presence Of Wind, Jatuporn Nakpiam

Mechanical and Aerospace Engineering Theses - Archive

This research effort develops a guidance and control system for a small airship to fly through assigned waypoints in the three dimensional space with a desired speed in the presence of wind and wind gust. In the control system development and validation, a simulation environment based on the nonlinear 6-DOF model of an airship, including the effect of the wind, is used. The airship has five control variables, the main thrust, the main thrust angle, the tail thrust, elevator and rudder deflections. The effectiveness of the elevator and rudder degrades as the speed of the airship decreases. The controller design …

Thermomechanical Behavior Of High-Temperature Shape Memory Alloy Ni-Ti-Pd-Pt Actuators, Douglas E. Nicholson

Electronic Theses and Dissertations

To date the commercial use of shape memory alloys (SMAs) has been mostly limited to binary NiTi alloys with transformation temperatures approximately in the -100 to 100 ºC range. In an ongoing effort to develop high-temperature shape memory alloys (HTSMAs), ternary and quaternary additions are being made to binary NiTi to form NiTi-X (e.g., X: Pd, Pt, Au and Hf) alloys. Stability and repeatability can be further increased at these higher temperatures by limiting the stress, but the tradeoff is reduced work output and stroke. However, HTSMAs operating at decreased stresses can still be used effectively in actuator applications that …

Development Of A Heat Transfer Test Rig For Finding Heat Transfer Characteristics Of Liquid Methane, Sergio Flores

Open Access Theses & Dissertations

Most large scale rocket engines use a regeneratively cooled system to cool the rocket engine using either the rocket fuel or oxidizer. The use of liquid methane as a rocket fuel is an emerging technology proving to have several advantages over current rocket fuels. However, liquid methane is lacking the extensive research as a rocket fuel compared to highly used rocket fuels like liquid hydrogen. A heat transfer test rig was built with the goal to characterize the heat transfer characteristics of liquid methane as it passes through a heated channel. The development of the test rig underwent considerations designed …

Determination Of Critical Parameters For Solar Probe Plus Shielding, Sergio Rafael Mendez

Open Access Theses & Dissertations

A methodology to determine critical design parameters such as critical "design" particle size, and critical "design" impact speed for the shielding of the Solar Probe Plus spacecraft was developed in this thesis. Several critical components and surfaces of the spacecraft such as the Solar Array North, the Thermal Protection System, and the ISIS Instruments were analyzed in this study. The methodology determines the critical "design" particle size based on the required reliability or probability of no impact. Current NASA methods do not provide means to calculate critical "design" impact speeds for missions such as Solar Probe Plus, where the distributions …

An Experimental Investigation On The Dynamics Of Bubbles Utilizing Refrigerant R134a Under Pressurized Flow Boiling Conditions, Keon Vereen

Electronic Theses and Dissertations

Flow boiling heat transfer allows for the dissipation of large amounts of heat. In this work, the effect of heat flux and pressure on flow boiling of liquid refrigerant R-134a is studied in a vertical thin channel. The experimental setup mimics a refrigeration cycle and specifically looks at the effect of pressure and wall heat flux on the departure size and bubble generation rate. The experimental setup consists of a closed loop which includes a vertical narrow rectangular channel and two synchronized high speed cameras for optical measurements at either sides of the channel. The setup is built to employ …

Dynamic Ergonomic Analysis And Simulation Of Fastening Operation, Akul Joshi

Doctoral Dissertations

"Operator performing fastening operation with powered hand-tools at awkward postures is subjected to external forces that may pose a risk of developing ergonomic injuries. For design of safe workplaces and selection of tools it is necessary to identify the probable causes of discomfort by simulating the work conditions and quantifying the risk factors. An ergonomic simulator is developed to simulate the fastening operation and quantify the effects of posture and force in fastening operation. The effect of dynamic forces is analyzed using two approaches. The first approach analyzes the effect of tool vibration while the second analyzes the hand-arm system …

Techno-Economic Analysis And Engineering Design Consideration Of Algal Biofuel In Southern Nevada, Jian Ma

Mechanical Engineering Faculty Research

As the biological and chemical technologies in algae biofuels production, engineering design, siting and resources are playing some dominant role in successfully developing and scaling locally. The southwest region in U.S. has been identified by DoE and the USDA as the most suitable area for developing algal biofuel production due to several merits like the high level of solar radiation, large arid land not good for food production. Among this region, Southern Nevada has unique advantage to grow microalgae biomass, which is the large amount of CO2 emission from about 16 power plants in Clark County to support the world …

Airplanes Donated To Andrews, Keri Suarez

Lake Union Herald

No abstract provided.

Parametric Analysis Of A Detonation-Type Turbofan, Yashwanth M. Swamy

Mechanical and Aerospace Engineering Theses - Archive

A new type of turbofan which detonates a fuel-air mixture was theoretically found to perform better than a conventional turbofan. A continuous detonation process is described and considered inside the core of the turbofan. The detonation-type turbofan needs certain modifications to detonate the fuel-air mixture at the core of the turbofan, namely, an annular detonation chamber to achieve continuous detonation. A parametric analysis of the new detonation-type turbofan was developed and used to calculate the performance parameters.

Focusing Of Longitudinal Ultrasonic Waves In Air With An Aperiodic Flat Lens, John T. Welter, Shamachary Sathish, Daniel Christensen, Philip Brodrick, Jason D. Heebl, Matthew Cherry

United States Air Force: Publications

Modeling and experimental results of an ultrasonic aperiodic flat lens for use in air are presented. Predictive modeling of the lens is performed using a hybrid genetic-greedy algorithm constrained to a linear structure. The optimized design parameters are used to fabricate a lens. A method combining a fiber-disk arrangement and scanning laser vibrometer measurements is developed to characterize the acoustic field distribution generated by the lens. The focal spot size is determined to be 0.88 of the incident wavelength of 8090 kHz at a distance of 2.5 mm from the lens. Theoretically computed field distributions, optimized frequency of operation, and …

Aether, Thomas Cameron, Kristine Colton, Daren Childers

Electrical Engineering

Aether is a RC-style autonomous air vehicle that utilizes GPS positioning along with a wireless communication system to achieve a computer-controlled flight.

This report will incorporate the acquisition, design, integration, implementation and testing phases of the UAV development. Furthermore a discussion of troubleshooting as well as improvements for future projects will be included.

Inherent And Model-Form Uncertainty Analysis For Cfd Simulation Of Synthetic Jet Actuators, Daoru Frank Han

Masters Theses

"A mixed aleatory (inherent) and epistemic (model-form) uncertainty quantification (UQ) analysis method was applied to a computational fluid dynamics (CFD) modeling problem of synthetic jet actuators. A test case, (Case 3, flow over a hump model with synthetic jet actuator control) from the CFDVAL2004 workshop was selected to apply the Second-Order Probability framework implemented with a stochastic response surface obtained from Quadrature-Based Non-Intrusive Polynomial Chaos (NIPC). Three uncertainty sources were considered: (1) epistemic uncertainty in turbulence model, (2) aleatory uncertainty in free stream velocity and (3) aleatory uncertainty in actuation frequency. Uncertainties in both long-time averaged and phase averaged quantities …

Uncertainty Quantification Integrated To Computational Fluid Dynamic Modeling Of Synthetic Jet Actuators, Srikanth Adya

Masters Theses

"The Point Collocation Non-Intrusive Polynomial Chaos (NIPC) method was applied to a stochastic synthetic jet actuator problem to demonstrate the integration of computationally efficient uncertainty quantification to the high-fidelity CFD modeling of Synthetic Jet Actuators. The uncertainty quantification approach was first implemented in two stochastic model problem cases for the prediction of peak exit plane velocity using a Fluid Dynamic Based analytical model of the Synthetic Jet Actuator, which is computationally less expensive than CFD simulations. The NIPC results were compared with direct Monte Carlo sampling results. To demonstrate the efficient uncertainty quantification in CFD modeling of synthetic jet actuators, …

A Numerical Study Of Novel Drag Reduction Techniques For Blunt Bodies In Hypersonic Flows, Christopher Marley

Masters Theses

"Numerical simulations of a full three-dimensional hemispherical body in hypersonic flow are conducted and innovative techniques involving forward injection of gas from the stagnation point of the sphere are investigated; techniques include annular (ring) and swirled injection both with and without upstream energy deposition. Objectives of the analysis are the assessment of 1) drag reductions achieved on the blunt body (including the detrimental drag effect caused by the forward-facing injection itself) and 2) stability characteristics of the jet. Studies are conducted at free-stream Mach numbers of 10 and 6.5 at standard atmospheric conditions corresponding to 30 km altitude. While centered …

Computational Investigation Of Plasma Actuator As An Active Flow Control Strategy Of Laminar Separation Bubbles, Justin Roger Aholt

Masters Theses

"A parametric computational study designed to examine the plausibility of an external body force generated by active means, such as a plasma actuator, as a means of controlling a Laminar Separation Bubble (LSB) over an airfoil at low Reynolds numbers was conducted. Computational Fluid Dynamics (CFD) was employed to characterize the effect that a body force, localized to a small region tangent to the airfoil surface, might have on an LSB. In this study, the effects of altering the strength and location of the "actuator" on the size and location of the LSB and on the aerodynamic performance of the …

Heat Transfer Augmentation In Rectangular Ducts Due To Passive Flow Destabilization, James Jackson Tinsley

Masters Theses

"The following thesis documents the comparison of surface enhancements in rectangular ducts for heat transfer enhancement of the air-side of off-road heat exchangers. Two sets of experiments were completed, one utilizing air as the working fluid, and the other utilizing water. Five air geometries and four water geometries were studied, including those with crosswise bumps, longitudinal vortex generators, and a unique rifling geometry. A smooth test section was also tested in the water experiments to verify the experimental setup. Such verification had been performed previously for the air experiments by Rucker [2007]. The experiment involved an applied constant heat flux …

Continuous Low Thrust For Small Spacecraft Proximity Operations, James Harris Meub

Masters Theses

"Recently, both DoD and NASA have demonstrated increased interest in the development of close proximity operations for space systems. AFRL's Advanced Sciences and Technology Research Institute for Astrodynamics (ASTRIA) has defined several key research topics relevant to military priorities, with one area of critical importance being the inspection and observation of low Earth orbit resident space objects (RSOs). This study investigates the feasibility of using a low-thrust cold-gas propulsion system to effectively and accurately facilitate resident space object inspection. Specifically, this study focuses on the Missouri S&T Satellite mission (M-SAT) as a means to demonstrate autonomous RSO inspection. This paper …

Shaker Table Vibration Testing Of A Microsatellite, Tonya Michelle Sanders

Masters Theses

"In the satellite development process, structural testing is a means to gain confidence in analytical models and ultimately support qualification of the spacecraft for flight. Vibration testing, in particular, is motivated by the safety considerations of crew or launch personnel, the survivability of delicate hardware and electronics, and the avoidance of large stresses that cause structural fatigue or failure. The subject of this thesis is concerned with the shaker table vibration testing of a microsatellite pair designed and built by students at the Missouri University of Science and Technology in Rolla, Missouri. A finite element model (FEM) used in structural …

Hall-Effect Thruster Surface Properties Investigation, David George Zidar

Masters Theses

"Surface properties of Hall-effect thruster channel walls play an important role in the performance and lifetime of the device. Physical models of near-wall effects are beginning to be incorporated into thruster simulations, and these models must account for evolution of channel surface properties due to thruster operation. Results from this study show differences in boron nitride channel surface properties from beginning-of-life and after 100's of hours of operation. Two worn thruster channels of different boron nitride grades are compared with their corresponding pristine and shadow-shielded samples. Pristine HP grade boron nitride surface roughness is 9000±700 Å, while the worn sample …

Design, Analysis, And Optimization Of Composite Structures For Aerospace Applications, Tyler Jason Keil

Masters Theses

"This thesis contains three papers that focus on composites that pertain to a variety of structures commonly found in the aerospace industry. The first paper presents an investigation of the stowage and deployment strength of a thin carbon fiber-reinforced polymer shell capable of being rolled and stowed in a tight rolled configuration. The intent of this structure is for use as a segment of a larger deployable reflective aperture. This study involved finite element analysis of several laminates, coupon-level and full-scale prototype testing, which provided a much needed insight and benchmark of composite shells used in this manner.

The second …

Numerical Study Of Drop Formation From Dripping To Jetting, Allouah Kadjo

Mechanical and Aerospace Engineering Theses - Archive

The formation of liquid droplet from a capillary tube has been examined using numerical simulations. The dimensions of the capillary tube and the flow velocity have been varied to observe the regimes of drop formation. There are three main regimes of drop formation, which are the periodic dripping, the dripping faucet and the jetting regimes. The mechanism of drop formation changes from one regime to another and involves different parameters. A particular emphasis has been placed on the velocity limits between the different regimes and the critical role played by instabilities in the generation of satellite drops. The algorithm used …

Numerical Modeling Of A Parallel Plate Electrowetting-On-Dielectric (Ewod) Device, Kevin Tully

Mechanical and Aerospace Engineering Theses - Archive

Numerical modeling and simulations have been performed in this study that focuses on modeling the fluid dynamics of an Electrowetting-on-Dielectric (EWOD) device. The case to be modeled in the present study is a droplet cutting problem where a droplet is sandwiched between two plates of Teflon and an electrical actuation will cause the droplet to cut or split into two smaller droplets. A finite difference method has been used to solve the Navier-Stokes equations, along with the continuity equation. An algorithm used for tracking the free surface is the Volume of Fluid (VOF) method. Along with using the VOF method …

Heat Transfer In Triangular Ducts With Axial Conduction,Containing Porous Medium, Abhishek Banerjee

Mechanical and Aerospace Engineering Theses - Archive

The objective of this study is to find a numerical solution for the velocity and temperature field in a duct of triangular cross-section area. A fully saturated porous medium is considered to be present in the duct. The study reports the contribution of axial conduction in heat transfer to flow passing through triangular porous passages. The terms in x-direction are retained in the energy equation due to the presence of axial conduction. Also, because of the geometrical asymmetry, non-orthogonal boundary conditions can exist and thus make the determination of heat transfer more difficult. The problem under consideration uses H2 boundary …

Nonlinear Finite Element Analysis Of Columns, Rajkiran Muppavarapu

Mechanical and Aerospace Engineering Theses - Archive

In many engineering applications structural components are considered to be beams or columns subjected to a range of external loads such as dead weight, wind, temperature changes etc.In this work a mathematical model has been developed for a sports lighting tower considering it to be a cantilever beam with large deformation. The concept of non-linear P-Delta analysis is applied to the column. Using this model, a tower analysis tool was developed in MATLAB. Using this tool various design alternatives can be examined to evaluate their suitability to a particular task.A number of example problems from the available literature were solved …