Aerospace Engineering Commons^™

A Fixed Robotic Mars Base Architecture, Christie Angunette Alston

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis proposes a fixed Mars base architecture consisting of the following interconnected elements: landing area, power generation, in-situ resource utilization (ISRU), robotic repair and assembly, and a scientific research laboratoiy. The base architecture that has been put forward can be expanded readily to include future elements such as a sustainable human habitat. The base architecture approach was developed assuming that serial Earth-launched lander missions were too expensive and too slow going forward in effecting the systematic exploration of a planet whose surface area constitutes nearly the same area as the land mass of Earth. The fixed base architecture facilitates …

Radiation Effects Basics For 7750, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint presentation created by Professor Bob Twiggs on "Radiation Effects Basics for 7750" on September 25, 2011.

Two-Dimensional, Time-Dependent Plasma Structures Of A Hall Effect Thruster, David Liu

Theses and Dissertations

The Hall thruster is a type of electric propulsion utilized by satellites to perform a wide variety of missions ranging from station keeping, orbital maneuvers, and even deep space propulsion. In order to accommodate the multitude of missions it also has a wide assortment of sizes and power configurations which can range from approximately an inch in diameter at 20 W to a couple of feet in diameter at 1.5 kW. Additionally, this electro-static device provides high specific impulse without the added weight penalty associated with conventional chemical thrusters. It supplies this high specific impulse by ionizing a gas such …

Increasing The Performance Of A Sliding Discharge Actuator Through The Application Of Multiple Potentials, Steven D. Seney Jr.

Theses and Dissertations

This work encompasses a comparison between a sliding discharge DBD actuator with grounded and AC biased sliding electrode driven at kHz frequency. The induced velocity in the bulk flow was recorded with PIV and compared for multiple potential splits between two test configurations and a baseline sliding discharge actuator over three test phases. In the first test phase, varying potential splits were examined between the primary and secondary electrode with the sliding electrode grounded. The potential splits induced a thicker induced jet than the baseline case with similar peak velocities on the order of 1.25 m/s at the 61 mm …

Design And Control Of Flapping Wing Micro Air Vehicles, Michael L. Anderson

Theses and Dissertations

Flapping wing Micro Air Vehicles (MAVs) continues to be a growing field, with ongoing research into unsteady, low Re aerodynamics, micro-fabrication, and fluid-structure interaction. However, research into flapping wing control of such MAVs continues to lag. Existing research uniformly consists of proposed control laws that are validated by computer simulations of quasi-steady blade-element formulae. Such simulations use numerous assumptions and cannot be trusted to fully describe the flow physics. Instead, such control laws must be validated on hardware. Here, a novel control technique is proposed called Bi-harmonic Amplitude and Bias Modulation (BABM) which can generate forces and moments in 5 …

Stochastic Real-Time Optimal Control: A Pseudospectral Approach For Bearing-Only Trajectory Optimization, Steven M. Ross

Theses and Dissertations

A method is presented to couple and solve the optimal control and the optimal estimation problems simultaneously, allowing systems with bearing-only sensors to maneuver to obtain observability for relative navigation without unnecessarily detracting from a primary mission. A fundamentally new approach to trajectory optimization and the dual control problem is developed, constraining polynomial approximations of the Fisher Information Matrix to provide an information gradient and allow prescription of the level of future estimation certainty required for mission accomplishment. Disturbances, modeling deficiencies, and corrupted measurements are addressed with recursive updating of the target estimate with an Unscented Kalman Filter and the …

Evaluation Of Nanocomposites For Shielding Electromagnetic Interference, Kenneth Y. Chong

Theses and Dissertations

Numerous efforts are ongoing to research and develop nanocomposite materials for space applications. Current composite spacecraft materials are nonconductive and require costly shielding materials to be applied in order to protect spacecraft from the harmful effects caused by electromagnetic interference (EMI), which is a by-product of exposure to the space environment. Conductive fillers (nanofibers) are being employed in composites to produce nanocomposites to reduce the dry weight of space vehicles while providing sufficient protection against EMI. This eliminates the need to apply secondary shielding materials to spacecraft. This thesis studied a nanocomposite consisting of Cycom 5575-2 glass with multi-walled carbon …

Effect Of The Thickness Of Undoped Gan Interlayers Between Multiple Quantum Wells And The P-Doped Layer On The Performance Of Gan Light-Emitting Diodes, T. Lu, S. Li, K. Zhang, C. Liu, Y. Yin, L. Wu, H. Wang, Xiaodong Yang, G. Xiao, Y. Zhou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

InGaN based light-emitting diodes (LEDs) with undoped GaN interlayer of variant thicknesses grown by metal-organic chemical vapor deposition technique have been investigated. It was found that the thickness of undoped GaN interlayers affected LEDs' performance greatly. The LED with 50 nm undoped GaN interlayer showed higher light output power and lower reverse-leakage current compared with the others at 20 mA. Based on electrical and optical characteristics analysis and numerical simulation, these improvements are mainly attributed to the improvement of the quality of depletion region by inserting an undoped GaN layer, as well as reduction of the Shockley-Read-Hall recombination in InGaN/GaN …

Space Environment-Iii Lecture - Powerpoint Presentation, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

Professor Bob Twiggs' lecture on Space Environment-III PowerPoint presentation delivered on September 2, 2011.

Space Environment - A Review, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint presentation created by Professor Bob Twiggs on "Space Environment" on September 2, 2011.

Mission Performance Considered As Point Performance In Aircraft Design, Robert A. Mcdonald

Aerospace Engineering

The cruise or loiter performance of an aircraft is intimately tied to its wing loading and its thrust-to-weight ratio. Paradoxically, mission performance is often not considered when these fundamental aircraft parameters are determined in conceptual design. In this paper, the traditional constraint diagram is extended to include contours of range or endurance parameter. These performance metrics represent the mission-performance capability of the aircraft without sizing the aircraft to a particular mission. This gives the designer an immediate and intuitive understanding of the tradeoff between the point and mission performance of the aircraft. The potential freedom for the designer to choose …

Designing Propulsion Systems For Future Aerospace Applications, Nihad E. Daidzic

Aviation Department Publications

No abstract provided.

Advances In Hydrogen Compression Ignition Internal Combustion Engines, Alberto Boretti

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The turbocharged direct injection lean burn Diesel engine is the most efficient engine now in production for transport applications within heavy duty trucks applications full load brake engine thermal efficiencies up to 45% and reduced penalties in brake engine thermal efficiencies reducing the load by the quantity of fuel injected. the secrets of this engine's performances are the high compression ratio and the lean bulk combustion mostly diffusion controlled in addition to the partial recovery of the exhaust energy to boost the charging efficiency. the major downfalls of this engine are the carbon dioxide emissions and the depletion of natural …

Flow Characteristics Of The Renovated Cal Poly 3 X 4 Ft Subsonic Wind Tunnel, Mathew L. Thomas, Dorian V. Pandey, Jason N. Nguyen

Aerospace Engineering

This paper investigates the flow characteristics of the renovated Cal Poly 3 x 4 ft subsonic wind tunnel. The IFA 300 constant-temperature anemometer along with a cross-plane X-wire dual-sensor probe was used to measure the mean velocity and turbulence intensity of the tunnel flow and part of the turbulent boundary layer at one section of the tunnel. Because of the malfunction of one channel of the IFA 300, only one wire of the dual sensor probe was calibrated for the measurements. The probe was then placed in a streamlined probe holder mounting on the traverse inside the wind tunnel. The …

Vibration-Based Health Monitoring Of Multiple-Stage Gear Train And Differential Planetary Transmission Involving Teeth Damage And Backlash Nonlinearity, Andrew Patrick Sommer

Master's Theses

The objective of this thesis is to develop vibration-based fault detection strategies for on-line condition monitoring of gear transmission systems. The study divides the thesis into three sections. First of all, the local stresses created by a root fatigue crack on a pinion spur gear are analyzed using a quasi-static finite element model and non-linear contact mechanics simulation. Backlash between gear teeth which is essential to provide better lubrication on tooth surfaces and to eliminate interference is included as a defect and a necessary part of transmission design. The second section is dedicated to fixed axis power trains. Torsional vibration …

Stoichiometric H2ice With Water Injection And Exhaust And Coolant Heat Recovery Through Organic Rankine Cycles, Alberto Boretti

Mechanical and Aerospace Engineering Faculty Research & Creative Works

High power density, stoichiometric, turbocharged, directly injected engines with water injection and a three-way catalytic converter after treatment have been proposed as one of the most promising H2ICE [1]. These throttle-controlled engines have top brake efficiencies exceeding 40%, but large penalties in efficiency reducing the load with 1 bar BMEP values approaching 10%. Recovery of the large amount of fuel energy lost in the coolant especially at low loads as well as the fuel energy lost in the exhaust that is significant at high loads and speeds may push not only the top brake efficiencies to exceed the 45% mark, …

Femtosecond Laser Fabricated All-Optical Fiber Sensors With Ultrahigh Refractive Index Sensitivity: Modeling And Experiment, Lan Jiang, Longjiang Zhao, Sumei Wang, Jinpeng Yang, Hai Xiao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

All-optical fiber sensors based on ultracompact fiber inline Mach-Zehnder interferometer (MZI) are fabricated by side-ablating a Ushape microcavity in a single-mode optical fiber with the fiber core partially removed using femtosecond (fs) laser pulses, in which the two light paths are accordingly formed in the remaining D-type fiber core and the U-shape microcavity. Beam propagation method (BPM) analysis is utilized to illustrate the dependences of good transmission spectra on parameters including the ablation depth, ablation length and the refractive index of Ushape microcavity, which gives some guidelines to optimize parameters for fs laser micromachining and predicts RI (refractive index) sensitivities …

Sitting In The Pilot's Seat: Optimizing Human-Systems Interfaces For Unmanned Aerial Vehicles, Steven Michael Queen, Kurt Sanner

STAR Program Research Presentations

One of the pilot-machine interfaces (the forward viewing camera display) for an Unmanned Aerial Vehicle called the DROID (Dryden Remotely Operated Integrated Drone) will be analyzed for optimization. The goal is to create a visual display for the pilot that as closely resembles an out-the-window view as possible. There are currently no standard guidlines for designing pilot-machine interfaces for UAVs. Typically, UAV camera views have a narrow field, which limits the situational awareness (SA) of the pilot. Also, at this time, pilot-UAV interfaces often use displays that have a diagonal length of about 20". Using a small display may result …

Simulation Of Wing Tip Vortices, Ryan Termath, Jason Lechniak, Keerti Bhamidipati

STAR Program Research Presentations

Modeling and Simulation (M&S) computational fluid dynamics (CFD) techniques were used to better understand wing tip vortices about a wing section. The CFD results were compared to experimental wind tunnel data derived from the University of Iowa (Ref. 2). The experiment used Stereoscopic Particle Image Velocimetry (SPIV) to measure the flow field. The SPIV data from the experiment illustrates the vortex core development and behavior downstream of the trailing edge of the wing section. Three CFD simulations using various mesh sizes and time steps were completed and compared to the experimental results. Two dimensional plots of modeled local flow field …

Unsteady Total Pressure Measurement For Laminar-To-Turbulent Transition Detection, Akane Sharon Karasawa

Master's Theses

This thesis presents the use of an unsteady total pressure measurement to detect laminar-to-turbulent transition. A miniature dynamic pressure transducer, Kulite model XCS-062-5D, was utilized to measure the total pressure fluctuations, and was integrated with an autonomous boundary layer measurement device that can withstand flight test conditions. Various sensor-probe configurations of the Kulite pressure transducer were first examined in a wind tunnel with a 0.610 m (2.0 ft) square test section with a maximum operational velocity of 49.2 m/s (110 mph), corresponding dynamic pressure of 1.44 kPa (30 psf). The Kulite sensor was placed on an elliptical nose flat plate …

Thermal Expansions In Wurtzite Aln, Gan, And Inn: First-Principle Phonon Calculations, L.-C. Xu, R.-Z. Wang, Xiaodong Yang, H. Yan

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Using the first-principle phonon calculations under the quasiharmonic approximation, thermal expansions in III-nitrides with wurtzite AlN, GaN, and InN are reported. The results showed that it is different for each thermal expansion of three III-nitrides at low temperatures, which is consistent with their Grneisen parameters as the function of temperature. Below 50 K, negative thermal expansions occur in InN, while GaN and AlN follow the rule of positive thermal expansion. To seek the origin of positivenegative thermal expansion distinction, the mode Grneisen parameters and the phonon spectra are investigated. They indicate that different low-frequency phonon vibration modes correspond to the …

The Future Of Aerospace Propulsion: Visco-Elastic Non-Newtonian Liquids, Nicole Arockiam

The Journal of Purdue Undergraduate Research

Aerospace propulsion often involves the spray and combustion of liquids. When a liquid is sprayed, large drops form first, in a process known as primary atomization. Then, each drop breaks up into smaller droplets, in a process known as secondary atomization. This determines final drop sizes, which affect the liquid’s evaporation and mixing rates and ultimately influence combustor efficiency. Little has been published concerning the secondary atomization of visco-elastic non-Newtonian liquids, such as gels. These substances have special potential as aerospace propellants, because they are safer to handle than their Newtonian liquid counterparts, such as water. Additionally, they can be …

Comparison Of Best Economy And Best Power Mixture Settings In The Purdue University Training Fleet, Charles G. Chrisman

Purdue Polytechnic Directed Projects

Purdue University operates a fleet of Cirrus SR20s as training aircraft. Standard operating procedures for the cruise portion of cross country training flights call for 65% power with a best power mixture, also called rich of peak, as opposed to a best economy setting, also called lean of peak. Previous work demonstrated that fuel consumption rates, cylinder head temperatures, and true airspeeds are lower when best economy is employed compared to best power for the same power output. This study confirmed that best economy is associated with a lower fuel consumption rate and lower cylinder head temperatures but was unable …

Comparison Of Turbine Engine Test Cell Airborne Nanoparticle Count Versus Ambient Background Particle Count, Ryne Larowe

Purdue Polytechnic Directed Projects

With the establishment of the National Test Facility for Aerospace Fuels and Propulsion at Purdue University in October of 2009, new equipment has been acquired to measure and classify exhaust emissions. This facility utilizes the Honeywell F109 turbofan and Pratt & Whitney PT-6 turboprop engine test cells to analyze the emissions and engine operation of new alternative aviation fuels. This observational study investigates what, if any difference there is in the amount of ambient residual Particulate Matter (PM) in the turbofan engine test cell when compared to ambient particle count associated with the Purdue University Airport (KLAF) property. The project …

Blair Balden, Margaret Von Steinen

International Faculty Researchers

A visiting professorship at the University of Passau in Passau, Germany for Dr. Blair Balden, a WMU associate professor of aviation, provided an excellent opportunity to share ideas and information about teaching aviation law with professors from Germany and Austria.

Comparison Of A High Purity Germanium Gamma Ray Spectrometer And A Multidimensional Nai(T1) Scintillation Gamma Ray Spectrometer, Greg Stratton

Aerospace Engineering

This report compares two different gamma ray spectrometers in terms of performance, operation, and apparatus and also investigates the design and integration challenges of using gamma ray spectrometers in space. The first spectrometer is a one-dimensional high purity germanium (HPGe) spectrometer and the second is a multidimensional NaI(Tl) scintillation spectrometer (MGRS). The key results show that the HPGe exhibits 15 to 27 times better energy resolution than the MGRS, but the MGRS is 52 times more sensitive and removes 177 % more of the background radiation.

3d Cfd On An Open Wheel Race Car Front Wing In Ground Effects, Thomas A. Price

Aerospace Engineering

The purpose of the report is to investigate the ability of the Fluent 6.3 k-ε Realizable turbulence model with standard wall functions to model the flow around the front wing of Cal Poly’s 2008 Formula SAE car. The three primary areas of interest are ground effects, the wing wheel interaction, and the wing tip vortices. Fluent was successful at modeling the increase suction from the ground effects, and the upwash due to the wing tip vortices. The results also displayed how the high pressure region in front of the tire propagates forward and interacts with the pressure distribution around the …

Modeling And Control For Heave Dynamics Of A Flexible Wing Micro Aerial Vehicle Distributed Parameter System, Lisa M. Kuhn

Doctoral Dissertations

In recent years, much research has been motivated by the idea of biologically-inspired flight. It is a conjecture of the United States Air Force that incorporating characteristics of biological flight into air vehicles will significantly improve the maneuverability and performance of modern aircraft. Although there are studies which involve the aerodynamics, structural dynamics, modeling, and control of flexible wing micro aerial vehicles (MAVs), issues of control and vehicular modeling as a whole are largely unexplored. Modeling with such dynamics lends itself to systems of partial differential equations (PDEs) with nonlinearities, and limited control theory is available for such systems.

In …

Astro Camp Presentation, Get Away Special Team 2011

Education and Outreach

No abstract provided.

A Taskable Space Vehicle: Realizing Cost Savings By Combining Orbital And Suborbital Flight, Thomas Co, Jonathan T. Black

Faculty Publications

The use of space gives the United States distinct advantages in any battlefield environment, but the high cost of space operations increasingly jeopardizes those advantages. Although the United States pioneered much of the current space technology, declining budgets for space research, development, and operations leave our legacy systems vulnerable to adversaries around the world. Other nations formerly incapable of space exploitation are quickly learning to counter US space technologies at surprisingly low costs. In order to reduce the expense of deploying and maintaining a robust space capability, the Department of Defense (DOD) must change the status quo in space operations …