Aerospace Engineering Commons^™

Low Thrust And Low Power Propulsion Systems Options For Small Satellites, Redha Amri

International Journal of Aviation, Aeronautics, and Aerospace

The present work focuses on the study of low thrust propulsion systems. Cold gas, thermal and monopropellant systems with a blow down depressurisation mode have been taken in consideration in this study. Most of propellants that can be used for small satellite propulsion systems were selected here in order to give the propulsion engineer many propellant options with a good idea about the performance of each propellant, and this is important to make a good trade-off during the system design. For cold gas and thermal propulsion, the propellants taken into account in this study are: Oxygen (O2), Nitrogen (N2), Hydrogen …

Performance Characteristics Design Of Pulsed Plasma Thrusters For Drag Counter-Reacting, Dr. Sam Dakka

International Journal of Aviation, Aeronautics, and Aerospace

Determining the performance characteristics of off the shelf pulsed plasma thrusters to enhance the life time of low earth orbiting platforms was investigated theoretically. Pulsed plasma thruster analysis was accomplished through development of correlations from historical data that distinguished between breech fed propellant to side fed propellant designs. Based on semi-empirical equations the power required by the thruster to counter react the drag was estimated and mapped for 1U to 27U CubeSat configurations for altitude ranging between 200km to 600km. It appears that the power required is dependent on the feeding delivery system design. For side fed designs the power …

Solar One: A Proposal For The First Crewed Interstellar Spacecraft, Alberto Caballero

International Journal of Aviation, Aeronautics, and Aerospace

In this paper it is presented the concept and design of a new type of spacecraft that could be used to make the first manned interstellar travel. Solar one would integrate three near-term technologies, namely: compact nuclear fusion reactors, extremely large light sails, and high-energy laser arrays. A system of lenses or mirrors to propel the sail with sunlight is suggested as an alternative to laser propulsion. With a mile-long light sail, Solar One could reach an average of 22% the speed of light, arriving to the closest potentially habitable exoplanet in less than 19 years with the help of …

Experimental Evaluation Of Strength Degradation Temperature For Carbon Epoxy Filament Wound Composite, Jai Krishna Mishra, Surya Prakash Rao Ch Dr, Subhash Chandra Bose P Dr, Kishore Nath N Dr, Rama Rao Golla Mr

International Journal of Aviation, Aeronautics, and Aerospace

Polymeric composites have been widely used in various structural and thermal aerospace applications. Polymeric composites having high strength and high modulus reinforcement are ideally suited for lot of critical aerospace applications as structure is designed with high specific strength and high specific modulus. In case of launch vehicles/ missile one such application is design and manufacturing of solid rocket motor casing with polymeric composites as it give high performance and reduces inert weight of propulsion system. The high specific strength and high specific modulus of composite materials makes it ideal choice for designing the composite rocket motor case (CRMC). These …

The Detrimental Effect Of Rainfall On Performance And Stability Characteristics Of Aircrafts-A Comprehensive Review, Praneeth Hr Mr, Amit Kumar Thakur Dr

International Journal of Aviation, Aeronautics, and Aerospace

The rapidly growing global market demands faster transit of human beings and goods even in unfavorable weather conditions of rainfall. The paper gives an overview of rain research methodologies, mathematical models to track raindrops in the flow field. The paper depicts the havoc rainfall causes on performance characteristics for various phases of flight in terms of evaluation of C_L and C_D and dynamic performance parameters such as short period mode. The knowledge obtained by this review paper could help designers to modify the design of aircraft such that it has better performance, stability, and control characteristics for all …

Real-Time Urban Weather Observations For Urban Air Mobility, Kevin A. Adkins, Mustafa Akbas, Marc Compere

International Journal of Aviation, Aeronautics, and Aerospace

Cities of the future will have to overcome congestion, air pollution and increasing infrastructure cost while moving more people and goods smoothly, efficiently and in an eco-friendly manner. Urban air mobility (UAM) is expected to be an integral component of achieving this new type of city. This is a new environment for sustained aviation operations. The heterogeneity of the urban fabric and the roughness elements within it create a unique environment where flight conditions can change frequently across very short distances. UAM vehicles with their lower mass, more limited thrust and slower speeds are especially sensitive to these conditions. Since …

Experimental And Computational Evaluation Of Five Hole Five Probe Flow Analyzer For Subsonic Wind Calibration, Akhila Rupesh Ms, J V Muruga Lal Jeyan Dr

International Journal of Aviation, Aeronautics, and Aerospace

It is very essential to predict the flow and its related parameters to understand real life fluid flow. The real-life fluid problems are studied with wind tunnels which gives very efficient results in practice. But in the case of wind tunnel studies flow angularities plays crucial role. Flow angularity determination includes measurement of static pressure, dynamic pressure and inflow angles. Flow prediction even hold a very strong hand in design process. Designing and testing being the foundation of any process industry, flow measurements and its related parameters have to be well evaluated. In such cases, wind tunnels play important role …

Assessment Of Egnos Performance For Civil Aviation Flight Phase In The Edge Coverage Area, Bilal Beldjilali, Salem Kahlouche, Lahouaria Tabti

International Journal of Aviation, Aeronautics, and Aerospace

The performances of the navigation systems used for different flight phases especially in the landing of an aircraft must be very high. The International Civil Aviation Organization defines the standards which must meet by any navigation systems to be certified, so it can be used by civil aircraft. To achieve the level of security defined by the International Civil Aviation Organization, new augmentation systems based satellites are developed. In Europe, the EGNOS system was developed to improve both GPS and Galileo performance. In this paper the performance of the EGNOS system for civil aviation flight phase was investigated. Four parameters …

Open-Ended Capstone Project: Designing And Manufacturing Of A Low-Cost Carbon Fiber Reinforced Composite Suborbital Rocket Payload Housing Using A 3d Printed Core, Garam Kim, Sergey Dubikovsky, Peng Hao Wang, Ronald Sterkenburg

International Journal of Aviation, Aeronautics, and Aerospace

Composite materials are utilized in many industries today due to its high performance and lightweight. However, the part manufacturing process of traditional composites is complicated and often involves high cost. The molds used for composite manufacturing are usually one of the contributors to the high part manufacturing cost. The authors demonstrated in this paper a manufacturing process for a carbon fiber reinforced composite rocket payload housing using an additively manufactured polylactic acid (PLA) payload housing core. The paper also demonstrates the designing and manufacturing of a functional product, which was used in a real-life application, achieved by college undergraduate students. …

Developing A Uas-Deployable Methane Sensor Using Low-Cost Modular Open-Source Components, Gavin Demali

Williams Honors College, Honors Research Projects

This project aimed to develop a methane sensor for deployment on an unmanned aerial system (UAS), or drone, platform. This design is centered around low cost, commercially available modular hardware components and open source software libraries. Once successfully developed, this system was deployed at the Bath Nature Preserve in Bath Township, Summit County Ohio in order to detect any potential on site fugitive methane emissions in the vicinity of the oil and gas infrastructure present. The deliverables of this project (i.e. the data collected at BNP) will be given to the land managers there to better inform future management and …

Design Of Banner Tow Mechanism For Bush Plane, Kyle Ciarrone, Ivan Martin, Rishabh Gadi, Tyler Brandt

Williams Honors College, Honors Research Projects

The 2019-2020 AIAA DBF objective was to design, build, and test a banner-towing bush plane that carries wooden passengers and luggage. Senior members on the team undertook the creation of the banner tow mechanism subsystem as their senior design project on behalf of the design team due to the challenge of its mechanical design and the aerodynamic considerations regarding its placement and enclosure aboard the aircraft. The competition as well as access to campus resources were canceled due to COVID-19, so full testing and integration of the mechanism was not achieved. However, the engineering design process was experienced from the …

Test Dummy Positioning For Autoliv Ogden, Ut, Dianne Althouse, John Garrett, Ty Johnston, Ridge Jones

Mechanical and Aerospace Engineering

• The Team shall deliver a proof of concept prototype to Autoliv for its use in positioning test dummies for Out-of-Position (OOP) airbag testing

• This is to improve set-up timing and accuracy without operator to operator variation.

• The device should work for the placing of three-year-old, six- year-old, and 5th percentile female test dummies.

• There are two OOP: head on IP (instrumentation panel) and chest on IP.

The Impact Of Human Assurance On Satellite Operations, Holly Handley, Dan Heimerdinger, Unal Tatar (Ed.), Adrian V. Gheorghe (Ed.), Omer F. Keskin (Ed.), Jean Muylaert (Ed.)

Engineering Management & Systems Engineering Faculty Publications

Mission assurance is a method to guarantee mission success against a known set of risks; mission assurance is generally represented as a probability against a threshold of acceptable performance. Human assurance can be considered as the likelihood of acceptable operator performance given a set of conditions that include the operator, the system, and the environment. Standard mission assurance models tend to assume a qualified crew, but do not include other aspects of the internal or external environment that may impact the reliability of the human operator. A human assurance model can be created that allows the exploration of the variability …

Foil-Based Additive Manufacturing System And Method, Hai-Lung Tsai, Yiyu Shen, Yingqi Li, Chen Chen

Patents

An additive manufacturing system, method of manufacturing, and fabricated part. The system uses a material joininglaser system to join together foil sheets to form a metal part. The material joining laser system can be configured to join adjacent foil sheets together in a substantially uniform manner. The manufacturing system also includes a material removal system that removes material from selected locations of the foil sheets to shape the foil sheets to correspond with selective slices of the part. The material removal system can be a laser system, such as a laser system configured to remove material from a foil sheet …

Thermal Performance Of Sierpinski Carpet Fractal Fins At Various Angles Of Inclination In A Natural Convection Environment, Haidar Jamil Khalil

College of Graduate Studies: Theses & Dissertations

As technology advances, higher performance cooling systems are desired to meet numerous thermal management challenges. Extended surfaces, also known as heat sinks or fins, are commonly used to passively dissipate unwanted heat from mechanical and electrical systems. Fractal fins in accordance with the first four iterations (including a base iteration) of the Sierpinski carpet, manufactured from AL-5052, were studied along seven different inclinations from 0° (orientated perpendicular to the direction of gravity) to 90° (orientated parallel to the direction of gravity), in iterations of 15°. The purpose of study was to investigate the thermal performance of the first four fractal …

Investigating The Numerical Stability Of Using An Impedance Boundary Condition To Model Broadband Noise Scattering With Acoustic Liners, Michelle E. Rodio, Fang Q. Hu, Douglas M. Nark

Mathematics & Statistics Faculty Publications

Reducing aircraft noise is a major objective in the field of computational aeroacoustics. When designing next generation quiet aircraft, it is important to be able to accurately and efficiently predict the acoustic scattering by an aircraft body from a given noise source. Acoustic liners are an effective tool for achieving aircraft noise reduction and are characterized by a frequency-dependent impedance value. Converted into the time-domain using Fourier transforms, an impedance boundary condition can be used to simulate the acoustic wave scattering by geometric bodies treated with acoustic liners. A Broadband Impedance Model will be discussed in which the liner impedance …

Global Technology Economic Analysis Paradigm, Iwasan D. Kejawa Ed.D

School of Computing: Faculty Publications

Abstract

Is true that it is not only the consumers that make the economy prospers? Business and government also play a role in the economy of a country and corporation. “The GLOBAL technology economy is driven perhaps by the example of a consumer-based society and capital driven citizenry," according to the article in the investor guide of 2013. The role of the government is very important in businesses, organizations and consumers alike depending on the decisions made by the government officials spending of the government. Research have indicated that dependencies of government, organizations, businesses and consumers are intertwine or intermediary. …

Impact Of Considering And Neglecting States On Descent-To-Landing Navigation, Kyle J. Demars, Kari C. Ward

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper develops a novel square-root formulation of the consider/neglect Kalman filter for navigation applications. The proposed filter partitions system parameters into three distinct categories: those to be estimated by the filter, those whose contribution to the system can be considered without explicitly estimating them, and those with sufficiently low effect on the system such that their contribution can be neglected altogether. Discussion on appropriate selection of consider and neglect parameters is provided with specific attention given to descent-to-landing navigation. Monte Carlo simulations and analysis are performed to assess the performance of the square-root consider/neglect filter.

Design And Analysis Of Descent-To-Landing Navigation Incorporating Terrain Effects, Kari C. Ward, Gunner S. Fritsch, J. Cameron Helmuth, Kyle J. Demars, James S. Mccabe

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This study investigated the ability of a navigation filter to process multiple terrain-based sensors, such as slant-range, slant-speed, and terrain relative navigation sensors, during a descent-to-landing scenario to estimate the state of a landing vehicle. The filtering technique leveraged was based upon a factorized form of the multiplicative extended Kalman filter, and terrain-based measurements were fused with star camera and inertial measurement unit sensor returns to estimate the position, velocity, and attitude of the landing vehicle. Monte Carlo simulations were carried out to assess the performance of the navigation filter along a lunar descent trajectory, as well as the consistency …

Experimental Investigation Of Ionic Liquid Mixtures For Electrospray Propulsion, Mitchell J. Wainwright

Doctoral Dissertations

"In recent years, there has been a dramatic increase in the number of small satellites (namely MicroSats, NanoSats, and CubeSats) in earth orbit; many of these are launched without propulsion systems. Multi-mode propulsion systems, capable of operating in either chemical or electric mode, have been proposed as attractive candidates for use in small satellites. Such systems are mass and volume optimal and flexible in terms of thrust requirements. Most previous work on multi-mode systems has focused on chemical mode performance.The work in this dissertation focuses on the electric mode performance of these propulsion systems.

The work in this research is …

Magnetic Control Of Transport Of Particles And Droplets In Low Reynolds Number Shear Flows, Jie Zhang

Doctoral Dissertations

“Magnetic particles and droplets have been used in a wide range applications including biomedicine, biological analysis and chemical reaction. The manipulation of magnetic microparticles or microdroplets in microscale fluid environments is one of the most critical processes in the systems and platforms based on microfluidic technology. The conventional methods are based on magnetic forces to manipulate magnetic particles or droplets in a viscous fluid.

In contrast to conventional magnetic separation method, several recent experimental and theoretical studies have demonstrated a different way to manipulate magnetic non-spherical particles by using a uniform magnetic field in the microchannel. However, the fundamental mechanism …

Development Of A Cold Gas Propulsion System For A 1u Cube Satellite, Norma Alicia Perea

Open Access Theses & Dissertations

In efforts to further the development test capabilities of nanosatellites on earth, NASA White Sands Test Facility (WSTF) is developing a Magnetic Levitation Table (MLT) for ground testing of nanosatellites. Testing of the table requires dedicated test articles that employ space-like systems, but those that can be used in the confines of a small lab testing area. In collaboration with WSTF, the University of Texas at El Paso (UTEP) Center for Aerospace Exploration Technology Research (cSETR) is developing an 1U cold gas propulsion cube-satellite demonstrator (CGD) to test capabilities of the levitation table. A 1U cube satellite was designed with …

Planar Motion Control Of A Cube Satellite Using Cold Gas Thrusters, Christian Lozoya

Open Access Theses & Dissertations

This Thesis presents a mathematical model developed for the computational simulation ofCubeSat movement using four thrusters that permit uniaxial translation and rotation. Arbitrary functions are fit to boundary conditions to simulate the force, acceleration, velocity, and displacement of the CubeSat along a plane. The model is used to derive a motion control algorithm assuming constant pressure and mass. A single model describes both translation and rotation. This Thesis also explores the relationship between propellant consumption and the time required to complete a displacement implied by the model.

Toward Adjoint-Based Aeroacoustic Optimization For Propeller And Rotorcraft Applications, Ramiz Ö. Içke, Oktay Baysal, Andy Moy, Leonard V. Lopes, Beckett Zhou, Boris Diskin

Mechanical & Aerospace Engineering Faculty Publications

The goal of the present project is to build a multidisciplinary, rapid, robust, and accurate computational tool to optimize wing-mounted propeller designs. The full Farassat’s formulation F1A for aeroacoustic analysis is implemented in the open-source software SU2. This extension enables the prediction of far-field noise generated by moving sources. The formulation is verified, for a stationary and rotating sphere in a wind tunnel and for a tiltrotor in forward flight, by comparing the acoustic predictions of SU2 with the predictions computed by NASA’s aeroacoustics code ANOPP2. The algorithmic differentiation capability of SU2 provides discretely consistent, adjoint-based sensitivity analysis for this …

Parametric Study Of A Turbojet Engine With Auxiliary Bypass Combustion- The Turboaux Engine, Kaleab Fetahi, Sharanabasaweshwara A. Asundi, Arthur C. Taylor, Adem H. Ibrahim, Syed Firasat Ali

Mechanical & Aerospace Engineering Faculty Publications

A parametric study of a novel turbojet engine with an auxiliary combustion chamber, nicknamed the TurboAux engine is presented. The TurboAux engine is conceived as an extension of a turbojet engine with an auxiliary bypass annular combustion chamber around the core stream. The study presented in this article is motivated by the need to facilitate clean secondary burning of fuel at temperatures higher than conventionally realized from air exiting the low-pressure compressor. The parametric study is initiated by performing a simple optimization analysis to identify optimal ‘fan’ pressure ratios for a series of conventional low-bypass turbofan engines with varying bypass …

Glue-Infused Rotating Nanofibers Net (Gronnet) For Capturing Space Debris- A Novel Debris Capturing System, Sneha M. Raibagi, Prithvi S.J. Monteiro, Rashmi K. Pallam, Amogh Anantha Murthy, Amit G. Gadag, Sharanabasaweshwara Asundi, Oleksandr Kravchenko

Mechanical & Aerospace Engineering Faculty Publications

It is evident that space debris is a growing concern, particularly in the low altitude Earth orbits, and if not addressed in time, may have a drastic socio-economic impact on civilization. This paper describes the Glue-infused Rotating Nanofibers Net (GRoNNet), a novel debris capturing system for pico/nano/micro-satellites (PNMSats). GRoNNet is designed as a modular, cost-effective system with the capability to capture target debris in multiple attempts and expedite its re-entry by attaching a debris mitigation system. It may be best described by comparing it with a chameleon’s tongue but several hundreds/thousands of them infused with a thick honey-like viscous adhesive …

A Prototype Virginia Ground Station Network, Zach Leffke, Jonathon Black, Kevin Shinpaugh, Ian Harnett, Bryce Clegg, Nick Angle, Chris Goyne, Connor Segal, William 'Trace' Lacour, Mike Mcpherson, Dimitrie Popescu, Samuel Jensen, Jason Harris, Mary Sandy, Mike Miller

Electrical & Computer Engineering Faculty Publications

This paper provides a detailed technical description of a prototype ground station network, the Virginia Ground Station Network (VGSN), developed for the Virginia Cubesat Constellation (VCC) mission. Virginia Tech (VT), University of Virginia (UVA), and Old Dominion University (ODU) have each constructed ground stations to communicate with their respective VCC spacecraft. Initially, each university was responsible for commanding its own spacecraft via its own ground station. As the mission progressed, it was decided to network the ground stations and operations centers together to provide backup communications capability for the overall mission. The NASA Wallops Flight Facility (WFF) UHF smallsat ground …

Estimation Of Atmospheric Conditions Over A Long Horizontal Path Using Multi-Frame Blind Deconvolution (Mfbd) Techniques In Comparison With Delayed Tilt Anisoplanatism (Delta) Software, Hannah Stoll

Dissertations, Master's Theses and Master's Reports

The potential to track and view objects in space from the ground with greater near real time knowledge of the intervening turbulence would be a revolutionary capability. The objective of this thesis is to cross-validate two separate methods used to estimate the Fried parameter. This verification is a step toward a commercial grade product that would make real-time estimates of the turbulence strength along an optical path from a ground-based observatory to a satellite in orbit around the Earth. Michigan Technological University has developed a multi-frame blind deconvolution (MFBD) algorithm used to estimate r0 and it was tested against MZA’s …

Strategies For Improving The Success Rates Of Lean Six Sigma Projects, Victoria Reed

Walden Dissertations and Doctoral Studies

Ineffective Lean Six Sigma (LSS) project strategies can lead to excessive Lean Six Sigma (LSS) project costs. Manufacturing business leaders who fail to mitigate LSS project costs expose the LSS project to failure. Grounded in the theory of constraints, the purpose of this qualitative single case study was to explore successful strategies LSS project leaders use to mitigate project costs in manufacturing. The participants comprised 16 aerospace manufacturing business leaders located in the southeast and northwest regions of the United States, who successfully implemented strategies to mitigate LSS project costs. Data were collected from semistructured interviews, a focus group, and …

An Experimental And Numerical Study Of High Temperature Gaseous Flow Through An Open Cell Silicon Carbide Foam Heater, Denis Pansolin

LSU New Orleans Theses and Dissertations

No abstract provided.