Aerospace Engineering Commons^™

Characterizing Premixed Syngas Combustion In Micro-Channels, Sunita Pokharel

Graduate Theses, Dissertations, and Problem Reports (ETD)

Increasing demands in the next-generation portable power-generation devices such as unmanned aerial vehicles (UAV), microsatellite thrusters, micro-chemical reactors and sensors calls for fuels with high specific energy and low emissions to meet the current demand of green energy. Fuel-lean synthesis gas (syngas) meets both these requirements exhibiting a promising route to a clean and green environment. Thus, it is of critical importance to characterize syngas combustion and understand its properties in the micro-combustion industry. In addition to complicated flame dynamics in microscale systems, varying the syngas-fuel mixture composition as well as the boundary conditions and geometry of a combustor significantly …

Fast Decision-Making Under Time And Resource Constraints, Kyle Gabriel Lassak

Graduate Theses, Dissertations, and Problem Reports (ETD)

Practical decision makers are inherently limited by computational and memory resources as well as the time available in which to make decisions. To cope with these limitations, humans actively seek methods which limit their resource demands by exploiting structure within the environment and exploiting a coupling between their sensing and actuation to form heuristics for fast decision-making. To date, such behavior has not been replicated in artificial agents. This research explores how heuristics may be incorporated into the decision-making process to quickly make high-quality decisions through the analysis of a prominent case study: the outfielder problem. In the outfielder problem, …

Aeroelasticity Of Composite Plate Wings Using Hsdt And Higher-Order Fem, Justin A. Haught

Graduate Theses, Dissertations, and Problem Reports (ETD)

The aeroelasticity of composite wings is becoming an increasingly researched topic in aircraft design, as designers continue to replace aluminum alloy components with those made of composite materials because of their favorable strength-to-weight ratio, fatigue characteristics, and corrosion resistance. Additionally, the bending-torsion coupling exhibited by composite laminates readily allow for the aeroelastic optimization of an aerodynamic structure through the process of aeroelastic tailoring. Wings made of composites materials, however, are more vulnerable to shear deformation.

The objective of the present research is to study the divergence and flutter characteristics of composite plate wings using a higher-order shear deformation theory (HSDT) …

Low-Cost Skewed Redundant Imu Configuration For State-Space Recovery In A Saturated Environment, Levi S. Hubbard

Graduate Theses, Dissertations, and Problem Reports (ETD)

Low-cost sensors for state space determination can be used successfully for ground vehicles, robots, unmanned aerial vehicles, and Internet-of-Things applications. When a high fidelity Inertial Measurement Unit (IMU) cannot be obtained for state space determination, low-cost sensors can be used to satisfactory standards, despite their limitations in capabilities, by using various implementation techniques. The research group was experimentally investigating state space information of an unstable flying vehicle for motion simulation validation. The high fidelity motion capture system would intermittently lose track of the flight vehicle which lost critical flight data.

The goal was to determine the potential of low-cost off-the-shelf …

Improving The Biological Control Of Persicaria Perfoliata (Polygonaceae) Using Rhinoncomimus Latipes Korotyaev (Coleoptera: Curculionidae), Jaewon Kim

Graduate Theses, Dissertations, and Problem Reports (ETD)

Persicaria perfoliata (L.) H. Gross (Polygonaceae; Mile-a-minute weed) is a rapid-growing invasive vine introduced from eastern Asia to northeastern United States in the 1930s. This vine has been invaded in disturbed areas and reforestation sites in 15 states in the U.S. and forms dense, monocultural patches that may inhibit natural forest regeneration. To control this weed, a host-specific biocontrol agent, Rhinoncomimus latipes Korotyaev (Coleoptera: Curculionidae) has been released in the P. perfoliata invaded states in the U.S. during the past 15 years. Currently, R. latipes is released by hand to the invaded area where the presence of the weed is …

Exploration Of Unknown Environments Using A Tethered Mobile Robot, Danylo Shapovalov

Graduate Theses, Dissertations, and Problem Reports (ETD)

Exploration with mobile robots is a well known field of research, but current solutions cannot be directly applied for tethered robots. In some applications, tethers may be very important to provide power or allow communication with the robot. This thesis presents an exploration algorithm that guarantees complete exploration of arbitrary environments within the length constraint of the tether, while keeping the tether tangle-free at all times. While a generalized algorithm that can be used with several exploration strategies is also proposed, the presented implementation uses a modified frontier-based exploration approach, where the robot chooses its next goal in the frontier …

Terrain Aware Traverse Planning For Mars Rovers, Gabrielle Hedrick

Graduate Theses, Dissertations, and Problem Reports (ETD)

NASA is proposing a Mars Sample Return mission, to be completed within one Martian year, that will require enhanced autonomy to perform its duties faster, safer, and more efficiently. With its main purpose being to retrieve samples possibly tens of kilometers away, it will need to drive beyond line-of-sight to get to its target more quickly than any rovers before. This research proposes a new methodology to support a sample return mission and is divided into three compo-nents: map preparation (map of traversability, i.e., ability of a terrain to sustain the traversal of a vehicle), path planning (pre-planning and replanning), …

Evaluating The Effectiveness Of Aerospace Materials, Vehicle Shape And Astronaut Position At Lowering The Whole Body Effective Dose Equivalent In Deep Space, Daniel K. Bond

Theses and Dissertations

As future crewed, deep space missions are being planned, it is important to assess how spacecraft design can be used to minimize radiation exposure. Collectively with shielding material, vehicle shape and astronaut position must be used to protect astronauts from the two primary sources of space radiation: Galactic Cosmic Rays (GCR) and Solar Particle Events (SPE). GCRs, which are composed of low intensity, highly energetic, and fully ionized stable and meta-stable isotopes, are considered a chronic source of radiation risk to the astronauts. SPEs, which originate from solar coronal mass ejections, are composed mostly of high intensity protons that can …

Peridynamic Approaches For Damage Prediction In Carbon Fiber And Carbon Nanotube Yarn Reinforced Polymer Composites, Forrest E. Baber

Theses and Dissertations

Aerospace structures are increasingly utilizing advanced composites because of their high specific modulus and specific strength. While the introduction of these material systems can dramatically decrease weight, they pose unique certification challenges, often requiring extensive experimental testing in each stage of the design cycle. The expensive and time-consuming nature of experimental testing necessitates the advancement of simulation methodologies to both aid in the certification process and assist in the exploration of the microstructure design space.

Peridynamic (PD) theory, originating from Sandia National Lab’s in the early 2000’s, is a nonlocal continuum-based method that reformulates the equation of motion into an …

Reliability Estimation Of Rotary Lip Seal In Aircraft Utility System Based On Time-Varying Dependence Degradation Model And Its Experimental Validation, Chao Zhang, Rentong Chen, Guanghan Bai, Shaoping Wang, Mileta M. Tomovic

Engineering Technology Faculty Publications

With several attractive properties, rotary lip seals are widely used in aircraft utility system, and their reliability estimation has drawn more and more attention. This work proposes a reliability estimation approach based on time-varying dependence analysis. The dependence between the two performance indicators of rotary lip seals, namely leakage rate and friction torque, is modeled by time-varying copula function with polynomial to denote the time-varying parameters, and an efficient copula selection approach is utilized to select the optimal copula function. Parameter estimation is carried out based on a Bayesian method and the reliability during the whole lifetime is calculated based …

Comparison Of Reynolds-Averaged Navier-Stokes Turbulence Models For Simulating Boundary Layers In Hypersonic Flows, Jorge-Valentino Kurose Bretzke

Masters Theses

“This study describes the use of Computational Fluid Dynamics (CFD) codes to simulate hypersonic boundary layers using several different turbulent closure models and comparing Reynolds-Averaged Navier-Stokes (RANS) simulations against Direct Numerical Simulations (DNS) of similar test cases. The test cases in this study consist of a flat plate in a Mach 8 freestream with a zero pressure gradient and wall recovery ratio of 0.48, as well as a Mach 8 axisymmetric nozzle also with a cold wall. The RANS models used in this study are the Spalart-Allmaras model, Baldwin-Lomax model, Menter K-Omega Baseline and Menter K-Omega Shear Stress Transport models. …

Characterization Of A Plasma Source Simulating Solar Wind Plasma In A Vacuum Chamber, Blake Anthony Folta

Masters Theses

"The United States has set an aggressive time line to not only return to the Moon, but also to establish a sustained human presence. In the Apollo missions dust was a significant factor, but the duration of those missions was short so dust and surface charging were problems, but they did not pose an immediate threat. For a long-term mission, these problems instead become incredibly detrimental. Because of this, research needs to be conducted to investigate these phenomena so that mitigation techniques can be developed and tested. To this end, this thesis serves to demonstrate the Gas and Plasma Dynamics …

Satellite Constellation Deployment And Management, Joseph Ryan Kopacz

Electronic Theses and Dissertations

This paper will review results and discuss a new method to address the deployment and management of a satellite constellation. The first two chapters will explorer the use of small satellites, and some of the advances in technology that have enabled small spacecraft to maintain modern performance requirements in incredibly small packages.

The third chapter will address the multiple-objective optimization problem for a global persistent coverage constellation of communications spacecraft in Low Earth Orbit. A genetic algorithm was implemented in MATLAB to explore the design space – 288 trillion possibilities – utilizing the Satellite Tool Kit (STK) software developers kit. …

Applications Of Drones In Atmospheric Chemistry, Travis J. Schuyler

Theses and Dissertations--Chemistry

The emission of greenhouse gases (GHGs) has changed the composition of the atmosphere during the Anthropocene. A major technical and scientific challenge is quantifying the resulting fugitive trace gas fluxes under variable meteorological conditions. Accurately documenting the sources and magnitude of GHGs emission is an important undertaking for discriminating contributions of different processes to radiative forcing. Therefore, the adverse environmental and health effects of undetected gas leaks motivates new methods of detecting, characterizing, and quantifying plumes of fugitive trace gases. Currently, there is no mobile platform able to quantify trace gases at altitudes(UASs), or drones, can be deployed on-site in …

Thermal / Structural Analysis Of The Hb 650 Thermal Shield, Gerald J. Smith

Graduate Research Theses & Dissertations

Fermilab’s PIP-II project’s superconducting linear accelerator (Linac) will drive the next generation of particle accelerators through a revolution in beam intensity. Key to beam intensification are the high efficiencies of niobium-tin superconducting radiofrequency (SRF) cavities operating at cryogenic temperatures near 5 Kelvin. A multifaceted approach is employed to achieve and maintain the extreme temperature. Vacuum provides the first barrier to thermal convection. Physical thermal intercept zones further isolate the exterior shell vacuum vessel at 300 Kelvin from the supercooled beamline. The first thermal intercept lies just inside the exterior vacuum vessel forming the 40 Kelvin zone. This 40K thermal shield …

Adaptive Filtration Of The Uav Movement Parameters Based On The Aoa-Measurement Sensor Networks, Igor Tovkach, Serhii Zhuk

International Journal of Aviation, Aeronautics, and Aerospace

Currently, the urgent task is to assess the small-sized maneuvering UAVs movement parameters. The location of an unknown UAV as a radio source can be determined using AoA measurements of the wireless sensor network. To describe the movement of a maneuvering UAV, a model is used in the form of a dynamic system with switching in discrete time. The values of switching variable determine type of UAV movement. To synthesize trajectory filtering algorithms, the Markov property of the extended process is used, which includes a vector of UAV movement parameters and a switching variable. The optimal trajectory filtering algorithm describes …

Bio-Inspired Method For Close-Proximity Operations On A Near-Earth Asteroid, Rene Alberto Valenzuela Najera

Open Access Theses & Dissertations

Space maneuvers in the vicinity of small celestial bodies and achieving a soft landing over the surface of small celestial bodies are essential movements to advance the status of exploration, collection of geographical data, measurement of physical properties among other on-orbit tasks. Before a spacecraft reaches hovering position over an asteroid in order to perform orbital tasks, close-proximity operations must be done. Since the movements of the spaceships depend on the acceleration forces provided by the thrusters and external disturbances forces, the correct planning of execution of the close-up trajectories on the celestial body orbit and trajectory to land on …

Wind Release Mechanical Sun Tracker, Tyler Andrus, Brady Fisher, Jt Gibson, Cynthia Rigby, Derek Smith

Mechanical and Aerospace Engineering

• Solar panel sun tracking system that releases solar panels to orient to wind flow in high wind conditions

• Operates on a single rotational motor

• Designed to be lightweight and portable

Afrl Downed Airman Recovery System, Daniel Cornia, James Bennett, Matthew Halton, Matthew Bennett, Brandon Haws, Tyson Compton, Jacob Needham, Daniel Spreier, Thory Van Dyke

Mechanical and Aerospace Engineering

For the 2020 Air Force Research Laboratory design competition, teams were challenged to develop a system to assist Combat Search and Rescue (CSAR) in recovering a downed pilot in contested waters.

In the event of a pilot ejecting from their aircraft, a GPS beacon notifies CSAR of the pilot’s approximate location. During the rescue operation, a swimmer from a CSAR crew enters the water and assists the isolated person (IP) to use rescue equipment.

The current procedure exposes an additional person to hazards and increases IP extraction time. The additional required personnel and setup time increases mission risk.

USU’s student …

Automated Cushion Ring Insertion System (Cris), Nathan Andersen, James Parberry, Chris Reid, Jeron Robbins, Kayden Atkin, Kody King, Mckay Mckinnon

Mechanical and Aerospace Engineering

Project Description

This purpose of this project is to prototype a proof of concept machine capable of installing a retaining ring into an airbag cushion.

Project Benefits

• Decreased installation time

• Better consistency and quality control

• Helps create a fully automated production line

Usu Baja Sae 2020, Adam Black, Trevor Nuamann, Cliff Rossberg, Ian Jeppsen, Tad Behunin, Josh Olsen, Kaulin Curtis

Mechanical and Aerospace Engineering

The 2020 USU Baja team addressed the following issues in the 2020 buggy design:

• Utilizing LotusSHARK software for suspension design: Completing a digital design of the buggy's suspension system in LotusSHARK allowed for optimization of suspension design.

• Redesign of brake system: Reducing the size of the brake pedal footprint was needed for increase space in the buggy for 4WD components.

• Implementation of 4WD: Significant bonus points could be earned in the SAE competition if the buggy has 4WD capabilities. The ability to switch between 2WD and 4WD was also desired to easily engage the best configuration for …

Heated Chamber Capable Of Purging/Scrubbing Twelve Or More Gas Analyzers Of Co2 And H20 For Calibration, Cole Watson, Oliver Hulme, Trevan Cottle

Mechanical and Aerospace Engineering

• Build ergonomically friendly chamber capable of purging 12 or more Gas Analyzers to keep up with current demand.

• Designed shelfing to fit all three Campbell Scientific, Inc. (CSI) gas analyzers: EC150, EC155, and Irgason.

• Chamber has uniform air temperature that will be regulated to not go above 50 ℃.

• CSI Datalogger is used to collect analyzer data and control electronics from outside the chamber.

• Chamber is durable and easily moved.

Autoliv Flexible Windshield Reaction Surface, Perry Simpson, Jacob Bowman, Joshua Christensen, Ethan Moore

Mechanical and Aerospace Engineering

Summary: Currently Autoliv is testing airbags against a flat steel plate. Testing against a steel plate doesn’t provide accurate airbag rebound data. Autoliv also does most of the development in series with automotive companies. They do initial designs but cannot get accurate tests until test vehicles are built.

Problem: Create a fixture that will bend a surface to replicate the curvature of any windshield desired resulting in more accurate airbag rebound data.

Why: Solving this problem will result in higher accuracy and precision in airbag performance systems. The new test fixture will provide a better representation of how the airbag …

Small Satellite Reaction Wheel, Corey Creager, Kalan Juhasz, Jeremy Wiser, Jake Laub, Christopher Wartena

Mechanical and Aerospace Engineering

• A reaction wheel uses torque to control the attitude of a satellite.

• The requirements specify a torque, a momentum, and a confined volume.

Solar Array Deployment Test Gravity Offloader System, Braden Call, Matthew Calvin, Chris Debenham, Christian Marriot, Mason Onkes

Mechanical and Aerospace Engineering

• Space Dynamics Lab (SDL) has started to develop larger satellites and larger solar arrays are required to power the spacecrafts. These larger arrays are harder to test

• Larger solar panels need their weight from gravity offloaded to prevent damage to their joints. The joints are not designed to hold their own weight

• Space Dynamics Lab requested our design be able to function in a vacuum to simulate the microgravity environment as closely as possible.

• While gravity offloading systems have been designed in the past, a vacuum-compatible and passive design brings a new and unique challenge

Usu Mars Rover Team, Usu Department Of Mechanical And Aerospace Engineering

Mechanical and Aerospace Engineering

The University Rover Challenge capstone project presents university students the opportunity to design, fabricate and test a rover to compete in the annual international Mars Society URC Competition held in Hanksville, Utah. The URC Competition consists of four separate missions including Extreme Retrieval & Delivery, Equipment Servicing, Science, and Autonomous Traversal. Each mission requires advanced subsystems onboard the rover to accomplish mission tasks in a timely manner.

The 2020 USU URC team is divided up into four subteams to accomplish each mission including Power/Drive, Navigation/Communications/Autonomy, Operations, and Science. Admission to the URC Competition is highly competitive since the competition is …

Westech Process Control, William Clarke, Ammon Mccarthy

Mechanical and Aerospace Engineering

The WesTech Engineering company is looking into utilizing MatLab Simulink to increase productivity.

Zagg Innovation Program: Led Focusing Case, Kyle Douglas, Travis Halverson, Derek Wilkins, Jessica Williams

Mechanical and Aerospace Engineering

Background: The ZAGG Innovation Program has the goal of creating innovative concepts and products for the telecommunication and consumer electronic retail channels.

Chosen Product: After deliberating over 30 generated product ideas with ZAGG representatives, the team chose to develop a phone case that would focus a cellphone camera flash into a practical flashlight beam.

Product Goals:

• Decrease beam angle and light increase projection distance

• Durability to withstand regular use and drops

• Keep the product as simple as possible, with minimal added bulk and parts

• Case will not obstruct the field of view of …

Uas For Public Safety Operations: A Comparison Of Uas Point Clouds To Terrestrial Lidar Point Cloud Data Using A Faro Scanner, Joseph S. Cerreta, Scott S. Burgess, Jeremy Coleman

International Journal of Aviation, Aeronautics, and Aerospace

Unmanned Aircraft Systems (UAS) can be useful tools for public safety agencies during crime or vehicle accident scene investigations if it can provide value to the resource-constrained agency. The speed of data collection, while minimizing first responder risk, while sustaining an acceptable level of accuracy and precision compared to other tools is where the agency may find value. During a recent homicide investigation in Florida, a UAS provided saved 81% in law enforcement labor hours with an acceptable level of accuracy compared to traditional methods. The purpose of this research was to compare UAS to determine if there were differences …

Identify Aerodynamic Derivatives Of The Airplane Attitude Channel Using A Spiking Neural Network, Nguyen Quang Vinh, Nguyen Duc Thanh, Hoang Minh Dac, Truong Dang Khoa

International Journal of Aviation, Aeronautics, and Aerospace

The paper proposes a method for identifying aerodynamic coefficient derivatives of aircraft attitude channel using spiking neural network (SNN) and Gauss-Newton algorithm based on data obtained from actual flights. Using SNN combination with Gauss-Newton iterative calculation algorithm allows the identification of aerodynamic coefficient derivatives in a nonlinear model for aerodynamic parameters with higher accuracy and faster calculation time. The paper proposes an algorithm to train the SNN multi-layer network by Normalized Spiking Error Back Propagation (NSEBP), in which, in the forward propagation period, the time of output spikes is calculating by solving quadratic equations instead of detection by traditional methods. …