Nuclear Engineering Commons^™

Characterization And Drying Of Oxyhydroxides On Aluminum Clad Spent Nuclear Fuel, Matthew Shalloo

Theses and Dissertations

Research reactors such as the Advanced Test Reactor (ATR) and the High Flux Isotope Reactor (HFIR) employ aluminum-clad fuel elements made up of many thin plates with uranium dispersed within. In most engineering applications, aluminum is considered to have favorable corrosion characteristics. It forms a thin oxide layer [Al2O3] under atmospheric conditions that is impenetrable to oxygen thus stopping any further corrosion. However, both aluminum metal and Al2O3 react with water to form hydrous oxides which are less protective against further corrosion and form significantly thicker layers than oxidation in dry air. As a result, aluminum-clad spent nuclear fuel (ASNF) …

Modeling Neutron Interaction Inside A 2d Reactor Using Monte Carlo Method, A. S. M. Fakhrul Islam

Theses and Dissertations

Scientists and engineers have been working for many years to develop accurate approaches to analyzing nuclear power reactors using computer codes that closely model the behavior of neutrons in a reactor core. The Monte Carlo simulation method is capable of treating complex geometries with a high level of resolution and fidelity to model neutron interactions inside a reactor core. With the requirement of accurate modeling in reactor physics and dynamics and great innovation of computer technology, Monte Carlo method is becoming an ever more powerful tool and receiving rising attention. In this study, Monte Carlo method is used to model …

Bison Simulation-Based Identification Of Important Design Criteria For U3si2 Fuels With Composite-Monolithic Duplex Sic Cladding, Jacob A. Yingling

Theses and Dissertations

Accident Tolerant Fuels (ATF) require a combination of fuel and cladding which have comparable longevity characteristics to UO2 while improving resistance to radiological release during and after accidents. U3Si2 has been proposed for use in ATF concepts for its high uranium density and high thermal conductivity which provide improved fuel performance. However, some of U3Si2’s material properties are not well understood. One such property, thermal creep of U3Si2, is an important contributing factor to U3Si2’s viability as an ATF. No experimentally derived thermal creep model is published for U3Si2, and previous analyses of compressive thermal creep experimental data lack statistical …

Modeling The Uranium-Silicon Phase Equilibria Based On Computational And Experimental Analysis, Tashiema Lixona Ulrich

Theses and Dissertations

As part of Accident tolerant fuel initiative, the uranium-silicide compound, U3Si2, is under consideration as a potential replacement for conventional uranium dioxide fuel. It is of interest as its higher uranium density of 11.3 g(U)/cm3 compared to 9.7 g(U)/cm3 for UO2 may allow use of more robust, but less neutronically economical fuel cladding. The improved uranium content would not only accommodate the neutronic penalty inherent to certain accident tolerant cladding concepts but also facilitate improved reactor performance with the potential for longer fuel cycles.

The U-Si system has been the subject of various studies that mainly focused on thermophysical properties, …

Possible Detection Of Low Energy Solar Neutrons Using Boron Based Materials, Nicole Benker, Elena Echeverria, Robert Olesen, Brant E. Kananen, John W. Mcclory, Yaroslav V. Burak, Volodymyr T. Adamiv, Ihor M. Teslyuk, George Glenn Peterson, Ben Bradley, Ethiyal R. Wilson, James C. Petrosky, Bin Dong, Jeffry Kelber, Jennifer Hamblin, Jaques Doumani, Peter A. Dowben, Alex Enders

Faculty Publications

Solar neutrons have been detected aboard the International Space Station (ISS), using lithium tetraborate and boron carbide detector elements. We find that evidence of a solar neutron flux, as detected in a neutron calorimeter following subtraction of the proton background, with an energy of about 2 to 4 MeV. This solar neutron flux is likely no more than 250 to 375 neutrons cm⁻²sec⁻¹, with a lower bound of 50–75 neutrons cm⁻²sec⁻¹ at one au.

Enabling Mobile Neutron Detection Systems With Clyc, Matthew C. Recker

Theses and Dissertations

Cs₂LiYCl₆:Ce³⁺ (CLYC) has the desirable property of being sensitive to both gamma rays and neutrons while producing waveforms suitable for pulse shape discrimination (PSD) to determine which radiation was detected. This dissertation examines the behavior of CLYC to support its further development for mobile and portable applications. First, the feasibility of performing PSD with CLYC and an inexpensive data acquisition system was examined. This system was able to clearly distinguish both events with a figure of merit of 1.42. Next, the performance of a SiPM was compared to a traditional PMT. Analysis showed that the …

Investigations Of Point Defects In Kh2Po4 Crystals Using Ab Initio Quantum Methods, Tabitha E. R. Dodson

Theses and Dissertations

Potassium dihydrogen phosphate (KH₂PO₄, or commonly called KDP) crystals can be grown to large sizes and are used for many important devices (fast optical switches, frequency conversion, polarization rotation) for high powered lasers. The nonlinear optical material has a wide intrinsic transparency range. Intrinsic point defects are responsible for several short-lived absorption bands in the visible and ultraviolet regions that affect high-power pulsed laser propagation. The primary intrinsic defects have been experimentally detected in KDP using electron paramagnetic resonance (EPR) experiments. The defect models established thus far include (i) self-trapped holes, (ii) oxygen vacancies, and (iii) …

Quantitative Analysis Of Cerium-Gallium Alloys Using A Hand-Held Laser Induced Breakdown Spectroscopy Device, Ashwin P. Rao, Matthew Cook, Howard L. Hall, Michael B. Shattan

Faculty Publications

A hand-held laser-induced breakdown spectroscopy device was used to acquire spectral emission data from laser-induced plasmas created on the surface of cerium-gallium alloy samples with Ga concentrations ranging from 0–3 weight percent. Ionic and neutral emission lines of the two constituent elements were then extracted and used to generate calibration curves relating the emission line intensity ratios to the gallium concentration of the alloy. The Ga I 287.4-nm emission line was determined to be superior for the purposes of Ga detection and concentration determination. A limit of detection below 0.25%was achieved using a multivariate regression model of the Ga I …

Point Defects In Lithium Gallate And Gallium Oxide, Christopher A. Lenyk

Theses and Dissertations

Electron paramagnetic resonance (EPR), Fourier-Transform Infrared spectroscopy (FTIR), photoluminescence (PL), thermoluminescence (TL), and wavelength-dependent TL are used to identify and characterize point defects in lithium gallate and β-gallium oxide doped with Mg and Fe acceptor impurities single crystals. EPR investigations of LiGaO₂ identify fundamental intrinsic cation defects lithium (V⁻_Li) and gallium (V²⁻_Ga) vacancies. The defects’ principle g values are found through angular dependence studies and atomic-scale models for these new defects are proposed. Thermoluminescence measurements estimate the activation energy of lithium vacancies at Ea = 1.05 eV and gallium vacancies at Ea > 2 …

Methods Of Use And Manufacture Of Silver-Doped, Nano-Porous Hydroxyapatite, Cheol-Woon Kim, Richard K. Brow

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

A silver-doped, nano-porous hydroxyapatite material is provided that can be utilized to capture radioactive iodine, ¹²⁹I. Methods of using the silver-doped, nano-porous hydroxyapatite material to remove radioactive iodine, and methods of manufacturing the material are also provided.

Experimental Investigation Of Steady-State And Transient Flow Boiling Critical Heat Flux, Soon Kyu Lee

Nuclear Engineering ETDs

The Critical Heat Flux (CHF) causes a rapid reduction of heat transfer coefficient with a rapid increase of cladding temperature, which may induce physical failure of the heated material. Understanding CHF phenomena and reliable prediction of the boiling behavior are needed to design a heat transfer system including nuclear reactors. Due to the complex nature of CHF, it is still an active research topic of interest. With an increasing interest in Accident Tolerant Fuel (ATF), CHF of ATF is essential topic of study for the detailed design of the fuel – cladding element and for the reactor safety analysis.

In …

The Blue Emission At 2.8 Ev In Strontium Titanate: Evidence For A Radiative Transition Of Self-Trapped Excitons From Unbound States, Miguel L. Crespillo, Joseph T. Graham, Fernando Agullo-Lopez, Y. Zhang, William J. Weber

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

The origin of the blue emission in SrTiO₃ has been investigated as a function of irradiation fluence, electronic excitation density, and temperature using a range of ion energies and masses. The emission clearly does not show correlation with the concentration of vacancies generated by irradiation but is greatly enhanced under heavy-ion irradiation. The intensity ratio of the 2.8 and 2.5 eV bands is independent of fluence at all temperatures, but it increases with excitation rate. The 2.8 eV emission is proposed to correspond to a transition from conduction band states to the ground state level of the self-trapped exciton …

Implementation Of View Factor Model And Radiative Heat Transfer Model In Moose, Abdurrahman Ozturk

Theses and Dissertations

View factors are functions that represent the geometric relationship between surfaces. They are important parameters for radiative heat transfer calculations. View factor catalogues are available for simple geometries in the current literature. However, in the case of complicated geometry, analytical or numerical methods are needed to evaluate view factors. The Monte Carlo (MC) method is the most flexible one among numerical methods, which are used to calculate view factors, since it can be applied to any geometry.

When experimental studies are not affordable to conduct, modeling of engineering problems gains more importance. Idaho National Laboratory (INL)’s finite element framework Multiphysics …

Nuclear Engineering At The Air Force Institute Of Technology: A Unique Graduate School Experience For A Unique Set Of Students, Michael B. Shattan

Faculty Publications

In August 2018, the Air University Commander formed a task force to review the Air Force’s Science, Technology, Engineering, and Mathematics (STEM) graduate education programs that are delivered and administered through the Air Force Institute of Technology (AFIT). The study was rooted in strategies to support the 2018 National Defense Strategy, and provided the necessary technologically equipped personnel for the 21st century. The study was commonly referred to as “reimagining AFIT”. Several themes emerged from the study, which include reaching a broader community of Airmen through alternate educational modes (e.g. distance learning, short course etc.), forming strategic educational and research …

Low-Power Core Reconfiguration For Missouri S&T Reactor (Mstr), Thaqal Alhuzaymi, Ayodeji Babatunde Alajo

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

The Missouri University of Sciences and Technology Reactor (MSTR) is pool-type research reactor which operates up to 200 kilowatt (kW). MSTR used for training and educating nuclear engineering students at Missouri S&T. A several of nuclear researches and irradiation experiments have been conducted in MSTR for example, neutron activation analysis (NAA), neutron radiography, radiolysis, image processing, etc. MSTR initial criticality took place on December 9, 1961. The first power level that MSTR operates at, was 10 kW. The power level alongside the core configuration was upgraded to the current ones, see Fig. 1. MSTR used light-water for moderation and natural …

Achieving High-Power Configuration In Missouri S&T Reactor (Mstr) For Potential Uprate, Thaqal Alhuzaymi, Ayodeji Babatunde Alajo

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

Research reactor is a powerful tool because of its wide contribution, almost to each field of science. It’s considered to be an essential element for advancing research, development and improvement in nuclear industry. The main goal of research reactor is to produce neutrons which are beneficially used for a wide range of applications such as industrial, agricultural, medical, etc. Neutron spectrum impact it uses. Commonly, neutrons with low energy level, up to 0.5 eV, called thermal neutrons where neutrons with intermediate energy level, ranging from 0.5 eV to 0.10 MeV, called epithermal "resonance" neutrons and neutron with high energy level, …

Nano Fab Lab 63, Brian K. Deemer, Josh Clemons, Nick Brodine, Delaney Fitzsimmons

Mechanical Engineering

Lawrence Livermore National Laboratories (LLNL) has several steps in the production process for ceramic nanofiber tubes that they would like to improve - electrospinning, cutting, rolling, sealing and heat treating. We undertook the challenge to deliver LLNL with a semi-automated process that efficiently integrates the steps of cutting, rolling, and sealing to save time and improve control over end dimensions. In this document, we discuss the technical background of the manufacturing steps currently followed to create nanofiber tubes, identify which steps are incorporated in our prototype and explain how they will interface with one another, define the design requirements, present …

Neutronic And Cfd-Thermal Hydraulic Analyses Of Very-Small, Long-Life, Modular (Vsllim) Reactor, Luis M. Palomino

Nuclear Engineering ETDs

Neutronic and CFD-thermal hydraulic analyses are performed of the Very-Small, Long-LIfe, and Modular (VSLLIM) nuclear reactor. This reactor was developed at the University of New Mexico’s Institute for Space and Nuclear Power Studies (UNM-ISNPS) to generate 1.0 – 10 MW_th for extended periods without refueling. It offers passive operation and safety features and redundant control and would be fabricated, assembled and sealed in the factory. During nominal operation and after shutdown, the VSLLIM is cooled by natural circulation of in-vessel liquid sodium, with the aid of an in-vessel chimney and annular helically-coiled …

Calculation And Tabulation Of Efficiencies For Tungsten Foil Positron Moderators, R. Alsulami, M. Albarqi, S. Jaradat, Shoaib Usman, Joseph T. Graham

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

Monte Carlo radiation transport simulations were used to calculate the positron stopping profiles in tungsten positron moderator foils. Stopping profiles were numerically integrated with efficiency kernels derived from Green's function solutions of the 3D diffusion equation to determine the moderation efficiency in both the backscattering and transmission geometries. Stopping profiles and efficiencies were calculated for positron energies from 10 keV to 10 MeV and incident angles from 0° to 75°. The resulting efficiencies agreed with other calculated and measured values in the literature, especially when similar values of the positron diffusion length and surface emission branching ratio were used. Large …

Numerical Study Of Spacer Grid Geometry In A 5 X 5 Nuclear Fuel Rod Bundle, Wan Chuan Fan

UNLV Theses, Dissertations, Professional Papers, and Capstones

Reactor fuel rod bundles serve as the primary heat source in light water reactors (LWRs), commonly found in the aforementioned PWR plants. The fuel rod bundles’ structure consists of a collection of fuel rods put into a parallel grid configuration. The bundles also include fuel rod spacers, which hold the fuel rods in place, in accordance with the grid. Repeating structures of the fuel bundles create the meta-structure in the reactor. In other words, the grid configuration repeats until it fills the entire space of the reactor. This results in reactor fuel rods suspended in the working fluid domain, oriented …