Nanoscience and Nanotechnology Commons^™

Crystalline–Amorphous Nanostructures: Microstructure, Property And Modelling, Binqiang Wei, Lin Li, Lin Shao, Jian Wang

Department of Mechanical and Materials Engineering: Faculty Publications

Crystalline metals generally exhibit good deformability but low strength and poor irradiation tolerance. Amorphous materials in general display poor deformability but high strength and good irradiation tolerance. Interestingly, refining characteristic size can enhance the flow strength of crystalline metals and the deformability of amorphous materials. Thus, crystalline–amorphous nanostructures can exhibit an enhanced strength and an improved plastic flow stability. In addition, high-density interfaces can trap radiation-induced defects and accommodate free volume fluctuation. In this article, we review crystalline–amorphous nanocomposites with characteristic microstructures including nanolaminates, core–shell microstructures, and crystalline/amorphous-based dual-phase nanocomposites. The focus is put on synthesis of characteristic microstructures, deformation …

Plasmon Enhanced Quantum Properties Of Single Photon Emitters With Hybrid Hexagonal Boron Nitride Silver Nanocube Systems, Mohammadjavad Dowran, Andrew Butler, Suvechhya Lamichhane, Adam Erickson, Ufuk Kilic, Sy_Hwang Liou, Christos Argyropoulos, A. Laraoui

Department of Mechanical and Materials Engineering: Faculty Publications

Hexagonal boron nitride (hBN) has emerged as a promising ultrathin host of single photon emitters (SPEs) with favorable quantum properties at room temperature, making it a highly desirable element for integrated quantum photonic networks. One major challenge of using these SPEs in such applications is their low quantum efficiency. Recent studies have reported an improvement in quantum efficiency by up to two orders of magnitude when integrating an ensemble of emitters such as boron vacancy defects in multilayered hBN flakes embedded within metallic nanocavities. However, these experiments have not been extended to SPEs and are mainly focused on multiphoton effects. …

Pamam- Cyclodextrin Conjugate Upregulates Brain-Derived Neurotropic Factor In Arpe-19 Cells, Gopika Ashokan

USF Tampa Graduate Theses and Dissertations

Background: Traumatic Brain Injury (TBI) is a major contributor to death and disability due to motorvehicle accidents, sports, physical abuse, and battlefield injuries. The primary insult to the brain leads to inflammation, vascular dysfunction, and oxidative stress in the brain as well as in the eye. This leads to loss of Retinal Ganglion Cells (RGCs) and downregulation of Brain derived Neurotopic Factor (BDNF). BDNF is a neurotrophic factor that binds to Tropomyosin Receptor Kinase B (TrkB) receptor to promote cell growth, survival, and differentiation. Current treatment strategies do not promote neuronal regeneration. Therefore, novel treatments are needed to restore vision …

Graphene Twistronics: Tuning The Absorption Spectrum And Achieving Metamaterial Properties, Ammar Armghan, Meshari Alsharari, Khaled Aliqab, Osamah Alsalman, Juveriya Parmar, Shobhit K. Patel

Department of Mechanical and Materials Engineering: Faculty Publications

Graphene twistronics using multilayer graphene is presented in such a way that it provides a metamaterial effect. This manuscript also analyzes the prediction of behavior using machine learning. The metamaterial effect is achieved by twisting the graphene layers. Graphene twistronics is a new concept for changing the electrical and optical properties of bilayer graphene by applying a small angle twist between the layers. The angle twists of 5^o, 10^o, and 15^o are analyzed for the proposed graphene twistronics design. Tuning in the absorption spectrum is achieved by applying small twists to the angles of the …

Heterogeneous Sensor Data Fusion For Multiscale, Shape Agnostic Flaw Detection In Laser Powder Bed Fusion Additive Manufacturing, Benjamin Bevans, Christopher Barrett, Thomas Spears, Aniruddha Gaikwad, Alex Riensche, Harold (Scott) Halliday, Prahalada Rao

Department of Mechanical and Materials Engineering: Faculty Publications

We developed and applied a novel approach for shape agnostic detection of multiscale flaws in laser powder bed fusion (LPBF) additive manufacturing using heterogenous in-situ sensor data. Flaws in LPBF range from porosity at the micro-scale (< 100 μm), layer related inconsistencies at the meso-scale (100 μm to 1 mm) and geometry-related flaws at the macroscale (> 1 mm). Existing data-driven models are primarily focused on detecting a specific type of LPBF flaw using signals from one type of sensor. Such approaches, which are trained on data from simple cuboid and cylindrical-shaped coupons, have met limited success when used for detecting multiscale flaws in complex LPBF parts. The objective of this work is to develop a heterogenous sensor data fusion …

Influence Of Dilute Silicon Carbide Nanoparticle Additions To The Microstructure And Mechanical Properties Of Laser Powder Bed Fusion Molybdenum, Nathan E. Ellsworth

Theses and Dissertations

Consolidation of pure molybdenum through laser powder bed fusion and other additive manufacturing techniques is complicated by a high melting temperature, thermal conductivity, and ductile-to-brittle transition temperatures. Nano-sized silicon carbide particles (0.1 wt%) were homogeneously mixed with molybdenum powder and the printing characteristics, chemical composition, microstructure, and mechanical properties were compared to pure molybdenum for scan speeds of 100, 200, 400, and 800 mm/s. The addition of silicon carbide improved the consolidation and mechanical properties and the oxygen content was reduced. Two mechanisms of oxygen reduction were identified as responsible for the improvements: oxidation of free carbon and the creation …

Mechanical Properties And Performance Of A Novel Nano-Engineered Unitized Composite With Quasi-Isotropic Layup, Brian Matthew Pudlo

Theses and Dissertations

Carbon nanotubes (CNTs) exhibit outstanding mechanical, electrical, and thermal properties, but are a challenge to effectively implement into macroscopic composites for aerospace applications. This research investigates the mechanical properties and performance of a newly developed hybrid NanoStitch composite, alongside a control polymer matrix composite, at room temperature. Both composite material systems investigated in this work have quasi-isotropic layup. Monotonic tension-tofailure, tension-tension fatigue, and creep tests were performed to characterize the performance of the composites under cyclic and sustained loading. Experimental results obtained for the quasi-isotropic NanoStitch composite were compared to those obtained for the quasi-isotropic control composite. The properties and …

Directing The Size And Dispersity Of Silver Nanoparticles Using Kudzu Leaf Extraction Solvents, Jaley F Adkins

College of Arts & Sciences Senior Theses

Kudzu is an invasive species in the Southeastern United States. Due to the abundance of its presence and the harm it causes to ecosystems, there has been interest in repurposing the species. Since many plants have medicinal and pharmaceutical uses, the use of kudzu in nanomaterials and bioanalytical chemistry may offer a way to repurpose the invasive species for applications in health science. Potential benefits include relief for the ecosystem from which kudzu is removed and societal benefits from environmentally friendly and sustainable reducing agents required in the synthesis of nanomaterials. The prospective use of kudzu as a non-toxic alternative …

Multifunctional Microgel-Based Cream Hydrogels For Postoperative Abdominal Adhesion Prevention, Bo Liu, Yunfan Kong, Olawale A. Alimi, Mitchell Kuss, Huiyin Tu, Wenfeng Hu, Abu Rafay, Kumar Vikas, Wen Shi, Megan Lerner, William L. Berry, Yulong Li, Mark A. Carlson, Bin Duan

Department of Mechanical and Materials Engineering: Faculty Publications

Postoperative abdominal adhesions are a common problem after surgery and can produce serious complications. Current anti-adhesive strategies focus mostly on physical barriers and are unsatisfactory and inefficient. In this study, we designed and synthesized advanced injectable cream-like hydrogels with multiple functionalities, including rapid gelation, self-healing, anti-oxidation, anti-inflammation, and anti-cellular adhesion. The multifunctional hydrogels were facilely formed by the conjugation reaction of epigallocatechin gallate (EGCG) and hyaluronic acid (HA)-based microgels and polyvinyl alcohol (PVA) based on the dynamic boronic ester bond. The physicochemical properties of the hydrogels including anti-oxidative and anti-inflammatory activities were systematically characterized. A mouse cecum-abdominal wall adhesion model …

Highly Dispersed Pt Nanoparticles Root In Single-Atom Fe Sites In Ldhs Toward Efficient Methanol Oxidation, Qing-Cheng Meng, Lin-Bo Jin, Meng-Ze Ma, Xue-Qing Gao, Ai-Bing Chen, Dao-Jin Zhou, Xiao-Ming Sun

Journal of Electrochemistry

Active and durable electrocatalysts for methanol oxidation reaction are of critical importance to the commercial viability of direct methanol fuel cell, which has already attracted growing popularities. However, current methanol oxidation electrocatalysts fall far short of expectations and suffer from excessive use of noble metal, mediocre activity, and rapid decay. Here we report the Pt anchored on NiFe-LDHs surface hybrid for stable methanol oxidation in alkaline media. Based on the high intrinsic methanol oxidation activity of Pt nanoparticles, the substrates NiFe-LDHs further enhanced anti-poisoning ability and maintained unaffected stability after 200,000 s cycle test compared to commercial Pt/C catalyst. The …

Formulation Of Encapsulated Nanoparticles Of Leek Extract As Antimicrobial And Anticancer Agent, Rawan Hassan Mohamed Elghanam

Theses and Dissertations

Leek extract (LEK) has broad therapeutic activity. However, plant extract use has many drawbacks, which could be resolved using nanocarriers. The purpose of this research work was to prepare chitosan nanoparticles (CS NPs) encapsulating LEK and investigate their antioxidant, antimicrobial, and anticancer activity. Gas chromatography-mass spectroscopy was used to determine the LEK components. The CS-LEK NPs were produced by tripolyphosphate (TPP) crosslinking with chitosan (CS) the ionic gelation methodology. The particle size was 331 nm, zeta potential (ZP) was 28.9 mv, polydispersity index (PDI) was 0.4, encapsulation efficiency (EE) was 65.6%, and loading capacity (LC) was 28.8 % of the …

Using Nanomaterials As Excellent Immobilisation Layer For Biosensor Design, Azeez Olayiwola Idris, Seyi Philemon Akanji, Benjamin O. Orimolade, Foluke Omobola Grace Olorundare, Shohreh Azizi, Bhekie Mamba, Malik Maaza

Research outputs 2022 to 2026

The endless development in nanotechnology has introduced new vitality in device fabrication including biosensor design for biomedical applications. With outstanding features like suitable biocompatibility, good electrical and thermal conductivity, wide surface area and catalytic activity, nanomaterials have been considered excellent and promising immobilisation candidates for the development of high-impact biosensors after they emerged. Owing to these reasons, the present review deals with the efficient use of nanomaterials as immobilisation candidates for biosensor fabrication. These include the implementation of carbon nanomaterials—graphene and its derivatives, carbon nanotubes, carbon nanoparticles, carbon nanodots—and MXenes, likewise their synergistic impact when merged with metal oxide nanomaterials. …

Polyethersulfone Thin-Film Nanocomposite Membrane Embedded With Amine-Functionalized Graphene Oxide For Desalination Applications, Ahmed Bahaeldin

Theses and Dissertations

Thin-film nanocomposite (TFN) desalination membranes were prepared based on a polyethersulfone (PES) support, where the polyamide (PA) layer was embedded with amine-functionalized graphene oxide (GO). The effect of adding various concentrations of functionalized and un-functionalized GO on the desalination performance, hydrophilicity, and morphology of the membranes was additionally assessed throughout this work. Scanning electron microscopy (SEM) measurements were used to assess the morphology of the membranes in combination with Brunauer-Emmett-Teller (BET) analysis. Contact angle measurements were used to gauge the hydrophilicity of the synthesized membranes. The membrane with the best desalination performance contained 1x10^-3 wt/vol% of functionalized GO in …

Research Progress In Cucurbit[N]Uril-Based Metal Nanomaterials For Electrocatalytic Applications, Zong-Nan Wei, Min-Na Cao, Rong Cao

Journal of Electrochemistry

Metal nanomaterials have exhibited excellent performance in electrocatalytic applications, but they still face the problems of poor stability and limited regulation strategies. It is an efficient strategy for greatly enhanced catalytic activity and stability by introducing a second component. In this review, we provide the sketch for the combination of metal nanomaterials and cucurbit[n]urils (CB[n]s) in electrocatalytic applications. CB[n]s are a series of macrocycles with rigid structure, high stability, and function groups for coordinating with metal sites, which make them promising to stabilize and modulate the metal nanomaterials for ideal performance. The discussion classifies the roles of CB[n]s, involving CB[n]s …

Non-Equilibrium Colloidal Phenomena In Magnetic Fields And Photoillumination: From Controlling Living Microbots To Understanding Microplastics, Ahmed Al Harraq

LSU Doctoral Dissertations

Colloids are a ubiquitous class of materials composed of microscopic particles suspended in a continuous phase which are found in everyday products and in nature. Colloids are also useful models for studying the spontaneous arrangement of matter from individual building blocks to mesophases. Standard treatment of colloid science is based on the assumption of equilibrium conditions, as defined in traditional thermodynamics. However, novel assembly mechanisms and motility are unlocked by pushing colloids away from equilibrium using external energy. In addition, many colloids in nature and in industrial applications exchange energy and mass with the surrounding environment thus behaving in a …

Interfaces In Dynamic Brittle Fracture Of Pmma: A Peridynamic Analysis, Longzhen Wang, Javad Mehrmashhadi, Florin Bobaru

Department of Mechanical and Materials Engineering: Faculty Publications

Recent experiments in bonded PMMA layers have shown dramatic changes in dynamic crack growth characteristics depending on the interface location and toughness. In this paper we present a peridynamic (PD) analysis of this phenomenon and determine three elements that are essential in a model reproducing the observed fracture behavior: (1) softening near the crack tip to account for changes in PMMA due to heat-generation induced by the high strain rates reached around the crack tip in dynamic fracture; (2) independent extension (mode I) and shear (mode II) modes of fracture; (3) a two-parameter fracture model, which matches both strength and …

Locally Resonant Metasurface For Low-Frequency Transmissive Underwater Acoustic Waves, Zhong Chen, Shenghong Guan, Qiang Xie, Zheng Li, Zhongmei Gao, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

Introduction: Acoustic metasurfaces for underwater wave manipulation have great potential use, but the strong solid-fluid interaction caused by impedance closeness between the structure and water brings design difficulty, especially in the low-frequency range.

Methods: Here a locally resonant metasurface for transmissive underwater acoustic waves is proposed using finite element method for which each metasurface unit consists of one channel and three subunits. Each subunit has one plate and two rubber spacers to form a resonator. By changing the height ratio of the plate over the subunit, arbitrary phase shifts within the full 2π coverage can be obtained at …

Solar-Light-Responsive Nanomaterials For The Photoelectrocatalytic Degradation Of Stubborn Pollutants, Benjamin O. Orimolade, Azeez O. Idris, Seyi Philemon Akanji, Folahan A. Adekola, Shohreh Azizi, Malik Maaza, Bhekie Mamba

Research outputs 2022 to 2026

Due to the ever increasing demand for cleaner water, a remarkable focus has been on the use of nanomaterials in wastewater treatment application. Photoelectrocatalytic (PEC) degradation, an advanced oxidation process which combines light and electrical energy, has been identified as a suitable technique capable of achieving total mineralisation of recalcitrant organic pollutants in wastewater. PEC degradation is non-selective, environmentally friendly and possesses great efficiency. The efficiency of PEC degradation has been enhanced by fabricating the photoanodes on a nanoscale with distinct morphologies. These nanostructured photoanodes have been extensively used for the removal of pharmaceuticals, dyes and phenolic water from wastewater. …

Architecture Of Heptagonal Metallo-Macrocycles Via Embedding Metal Nodes Into Its Rigid Backbone, A.M.Shashika D. Wijerathna, He Zhao, Qiangqiang Dong, Qixia Bai, Zhiyuan Jiang, Jie Yuan, Jun Wang, Mingzhao Chen, Markus Zirnheld, Rockwell T. Li, Yuan Zhang, Yiming Li, Pingshan Wang

College of Sciences Posters

Metal-organic macrocycles have received increasing attention not only due to their versatile applications such as molecular recognition, compounds encapsulation, anti-bacteria and others, but also for their important role in the study of structure-property relationship at nano scale. However, most of the constructions utilize benzene ring as the backbone, which restricts the ligand arm angle in the range of 60, 120 and 180 degrees. Thus, the topologies of most metallo-macrocycles are limited as triangles and hexagons, and explorations of using other backbones with large angles and the construction of metallo-macrocycles with more than six edges are very rare.

In this study, …

An Efficient And Low-Cost Method To Create High-Density Nitrogen-Vacancy Centers In Cvd Diamond For Sensing Applications., Prem Bahadur Karki, Rupak Timalsina, Mohammadjavad Dowran, Ayodimeji E. Aregbesola, Abdelghani Laraoui, Kapildeb Ambal

Department of Mechanical and Materials Engineering: Faculty Publications

The negatively charged Nitrogen-Vacancy (NV^-) center in diamond is one of the most versatile and robust quantum sensors suitable for quantum technologies, including magnetic field and temperature sensors. For precision sensing applications, densely packed NV^- centers within a small volume are preferable due to benefiting from 1/√𝑁 sensitivity enhancement (N is the number of sensing NV centers) and efficient excitation of NV centers. However, methods for quickly and efficiently forming high concentrations of NV^- centers are in development stage. We report an efficient, low-cost method for creating high-density NV^- centers production from a relatively …