Mechanical Engineering Commons^™

Evaluation And Sizing Of Solar Powered Reverse Osmosis Water Desalination System, Sandip Subedi

Honors Theses

About 71 % of the surface of Earth is water, out of which around 2.5 % is freshwater. The majority of the surface of Earth is occupied by seawater which also contains dissolved salt. The salt concentration in seawater makes it toxic to humans because the human body is unable to get rid of the salt that comes from seawater. The demand for fresh water is increasing due to the rise in global population. In this context, desalinated seawater is considered as a viable resource to meet the growing demand for fresh water. Desalination process is highly energy intensive due …

Feasibility Study Of Portable Solar Powered Blood Storing Refrigerator, Saroj Subedi

Honors Theses

This report is focused on the preliminary feasibility of portable solar-powered blood-storing refrigerators primarily based on calculations of energy required to maintain the temperature of the refrigerator, the electricity required throughout the day, calculating sufficiency of power supplied by the solar panel, and selection of battery for power storage. The method and the trend of a feasibility study involve the study of blood properties, separation of blood components after donation, and their storage conditions. Then, the portable size of the refrigeration has been proposed with three different compartments for storage of each blood component. The further methods involve the selection …

Using Blade Element Momentum Methods With Gradient-Based Design Optimization, Andrew Ning

Faculty Publications

Blade element momentum methods are widely used for initial aerodynamic analysis of propellers and wind turbines. A wide variety of correction methods exist, but common to all variations, a pair of residuals are converged to ensure compatibility between the two theories. This paper shows how to rearrange the sequence of calculations reducing to a single residual. This yields the significant advantage that convergence can be guaranteed and to machine precision. Both of these considerations are particularly important for gradient- based optimization where a wide variety of atypical inputs may be explored, and where tight convergence is necessary for accurate derivative …

Design And Production Of A Bathtub Caddy, John Marquez

Honors Theses

The purpose of this thesis is to document and discuss the design and manufacturing process used to produce a bathtub caddy on a large-scale production process for the Center for Manufacturing Excellence Senior Capstone Project. This project was carried out over the Fall of 2020 and Spring 2021 semesters by a team consisting of an Undergraduate Chemical Engineering Undergraduate, two Mechanical Engineering Undergraduate, a Finance Undergraduate, and an Accounting Undergraduate. The objective of this project was to design the product and then a manufacturing process that could be used to at first produce a prototype before planning a ramp up …

Flagellation Testing Of Composite Finger Skirts For Surface Effect Ship (Ses) Application, Natalie Marie Holliday

Theses and Dissertations

The objective of this research is to create flagellation data for SES finger skirts. The SES design allows it to have a high tonnage with low draft, little drag, low wavemaking resistance, remarkable carrying capacity, and incredible propulsive efficiency. A SES is a sidehull hovercraft, with air cavity sealing components at the bow and stern. The fingers at the bow collectively make up an elastic, flexible full sealing skirt, dissipating oncoming waves and allowing for the vessel to be self-stabilizing. The problem with SES vessels is that the bow finger skirts wear significantly over a short period of time (~ …

Replication And Tribological Engineering Of Physical Surfaces Using Two-Photon Lithography, Shelby Robert Maddox

Graduate Theses and Dissertations

Up to one-fifth of all energy consumed each year goes directly to overcoming frictional effects. This waste will remain even if renewable energy becomes feasible as a large-scale replacement for conventional fuel sources. If that wasted energy could be saved instead, then overall energy consumption could either decrease or be redirected to where it would be most beneficial to human and environmental flourishing. To this end, there is a need for strategies and techniques to reduce frictional energy loss. It is well established that surface texturing can be used to reduce friction. There are many industrial methods in current use …

Inverse Methods For Near-Real Time Estimation Of Surface Heat Flux In Thermal Protection Systems For Space Vehicles, Obinna Oluchukwu Ugochukwu Uyanna

Theses and Dissertations

With the increased goal of manned explorations to outer space, safety during the atmospheric entry/reentry process is paramount as the incident heat fluxes on the surface of vehicle can reach critical values. Thermal Protection Systems (TPS) are therefore essential components in space vehicles as they ensure the safety and protection of the payload and cargo. In order to ensure improved active control capabilities and prolonged used of the vehicle, TPS surface conditions need to be known and determined. Since direct measurement of the surface heat flux using sensors is not feasible, one alternative involves the use of temperature sensors located …

Development Of An Intraperitoneal Catheter Placement Device For Use On The Battlefield, Riley Reynolds

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The objective of this project was to simplify peritoneal cavity access so an Airforce field medic can safely infuse oxygen microbubbles (OMBs) into the intraperitoneal space for the emergency treatment of hypoxia due to lung damage. To solve this problem, we created an intraperitoneal catheter placement device for use on the battlefield. The three common methods and some of the most common devices for peritoneal cavity access were reviewed. Injury frequencies for each of the three methods were analyzed. The results showed that each of the access techniques gives a similar rate of iatrogenic injury.

The battlefield conditions where the …

Multi-Degree Of Freedom Position And Attitude Control Of Rings Dipoles Using Electromagnetic Forces And Torques, David Andres Alvarez

Theses and Dissertations

Satellite formation flight (SFF) is likely to transform and advance the scope of space missions in the near future. Some considerable benefits of SFF to a mission include robustness, adaptability, and potential cost savings. However, satellite formations face a fuel expenditure issue: the more spacecraft there are to control, the more fuel will be expended on alignment and maneuvering. A solution to this problem is Electromagnetic Formation Flight (EMFF), which is the application of conductive coils in producing electromagnetic fields that can interact with the fields of other coils in a formation to exchange forces and torques. With three orthogonal …

Additive Manufacturing And Mechanical Properties Of The Dense And Crack Free Zr-Modified Aluminum Alloy 6061 Fabricated By The Laser-Powder Bed Fusion, Abhishek Mehta, Le Zhou, Thinh Huynh, Sharon Park, Holden Hyer, Shutao Song, Yunali Bai, D. Devin Imholte, Nicolas E. Woolstenhulme, Daniel M. Wachs, Yongho Sohn

Mechanical Engineering Faculty Research and Publications

For additive manufacturing such as laser powder bed fusion (LPBF), commercial aluminum alloy (AA) 6061 is typically considered unsuitable due to formation of solidification cracking and/or excessive porosity. In this study, to improve buildability/printability of AA6061, 1 wt% of Zr was alloyed to produce Zr-modified AA6061 by LPBF. Powders of unmodified and Zr-modified AA6061 were produced by gas atomization, and utilized as a feed-stock for the LPBF to fabricate specimens for microstructural examination and mechanical testing. The as-built unmodified AA6061 exhibited poor printability due to formation of cracks and porosity in the microstructure regardless of LPBF parameters. However, the Zr-modified …

High Strength We43 Microlattice Structures Additively Manufactured By Laser Powder Bed Fusion, Holden Hyer, Le Zhou, Qingyang Liu, Dazhong Wu, Shutao Song, Yuanli Bai, Brandon Mcwilliams, Kyu Cho, Yongho Sohn

Mechanical Engineering Faculty Research and Publications

WE43 is a high strength, high creep resistant Mg-alloy containing Y, Nd, and Zr, and has potential for many lightweight structural applications in the automotive, aerospace, and biomedical industries. Additive manufacturing technology such as laser powder bed fusion (LPBF) brings an opportunity to produce complex geometries such as lattice structures. In this study, fabrication, compressive behavior, and fracture modes of 24 different microlattice structures were investigated by varying unit cell type, strut diameter, and number of unit cells. These complex lattice structures were produced by LPBF using the parameter set: laser power = 200 W, scan speed = 1100 mm/sec, …

Introduction Of New Value Stream Through Vermicomposting Process, James Spalding, Joseph Harris

Honors Theses

The purpose of our project is to analyze whether a waste byproduct can be monetized into a viable profit stream for Wonderbird Spirits. Spent grain, a waste byproduct created by the distillation process, is currently the company’s biggest source of material waste. The CME project team designed and built a trommel to aid liquid-solid separation of the spent grain so that the solid portion can be repurposed as feedstock for a vermicomposting setup. We also suggest vermicomposting setup for the distillery based on the needs and capabilities of Wonderbird Spirits. We present financial analyses detailing the cost of creating the …

Advancing The Use Of Quality Control Tools For High-Density Data In Modern Manufacturing, Romina Dastoorian

Dissertations

In modern manufacturing, advanced metrology systems are continually being incorporated into quality control (QC) systems to provide high-density (HD) datasets. These datasets can contain millions of measurements that can be used to represent a part’s whole geometry. While integrating HD datasets into QC systems has brought several opportunities to enhance the performance of QC systems, it has resulted in new challenges in this area as well. While significant amounts of research have been performed in this area, the QC research community still strives to tackle these challenges. This study identifies key challenges regarding incorporating HD datasets into QC systems. Specifically, …

The Effect Of Simulated Mangrove Forest Width On Shoreline Stabilization At Multiple Tidal Water Levels, James Edward Austin

Theses and Dissertations

Red mangrove (Rhizophora mangle) forests protect hundreds of miles of Florida’s shorelines from erosion and wave damage associated with severe storms and daily wave action. Shorelines are often protected from erosion with man-made structures such as seawalls, revetments, and breakwaters. However, these man-made structures disrupt natural ecosystems and cause scour and erosion in surrounding areas. The presence of mangroves not only prevents erosion but shelters marine life and filters water, promoting ecological health. Mangroves are now being implemented for wave energy reduction and shoreline stabilization, but there is little quantitative data about the precise sediment transport induced or prevented by …

Performance And Economics Of Solar Inverters And Module Level Power Electronics In A 1 Mw Photovoltaic System, Maxwell Criswell

Biological and Agricultural Engineering Undergraduate Honors Theses

Photovoltaic solar panels convert sunlight to electricity in the form of direct current; therefore, a necessary component of every photovoltaic system is an inverter to convert the electricity to usable alternating current. There are various commercially available inverter technologies manufactured today such as microinverters, string inverters, and central inverters, as well as module level power electronic devices such as DC optimizers that are capable of improving system performance in string and central inverter systems. This thesis compares the performance and economics of five different inverter and module level power electronic systems through model simulation using Helioscope software. The five alternatives …

Binary Particle Mixtures As A Heat Transfer Media In Shell-And-Plate Moving Packed Bed Heat Exchangers, Chase Ellsworth Christen

Boise State University Theses and Dissertations

Solid particles are being considered in several high temperature thermal energy storage systems and as heat transfer media in concentrated solar power (CSP) plants. The downside of such an approach is the low overall heat transfer coefficients in shell-and-plate moving packed bed heat exchangers caused by the inherently low packed bed thermal conductivity values of the low-cost solid media. Choosing the right particle size distribution of currently available solid media can make a substantial difference in packed bed thermal conductivity, and thus, a substantial difference in the overall heat transfer coefficient of shell-and-plate moving packed bed heat exchangers. Current research …

First-Principles Studies Of Nucleation Of Atomic-Layered Molybdenum Disulfide By Atomic Layer Deposition, Matthew Lawson

Boise State University Theses and Dissertations

This dissertation implements first-principles calculations to understand the nucleation mechanisms for atomic layer deposition (ALD) of molybdenum disulfide (MoS₂) using MoF₆ and H₂S precursors. ALD is a self-limiting process that can deposit a range of materials at the nanoscale, while maintaining chemical stoichiometry, atomic scale thickness control, and can conform to high-aspect ratio substrate designs. ALD is extremely sensitive to surface chemistry and morphology; therefore, it is critical to understand how these factors control deposition.

Density functional theory (DFT) was used to understand what factors can control the nucleation for ALD of MoS₂ using …

Plasma Aerodynamics: Experimental Quantification Of The Lift Force Generated On An Airfoil Using Plasma Actuation To Estimate Power Requirements In Small Uav Applications, Getachew Ashenafi

UNLV Theses, Dissertations, Professional Papers, and Capstones

This research addressed the amount of electric power required to induce specific changes in lift force using a NACA 2127 airfoil with a chord length of ~28 mm, connected to a micro load cell, in a wind tunnel of 103 square centimeter cross-section. A DBD plasma actuator supplied by a ZVS driven high voltage pulsed DC circuit, operating at a frequency of 17.4 kHz, was utilized for voltages of up to 5000 V. Two configurations of electrode gapping were compared to determine the efficient use of power. The configuration with a gap of ~1 mm between the upstream and downstream …

A Hyperelastic Porous Media Framework For Ionic Polymer-Metal Composites And Characterization Of Transduction Phenomena Via Dimensional Analysis And Nonlinear Regression, Zakai J. Olsen

UNLV Theses, Dissertations, Professional Papers, and Capstones

Ionic polymer-metal composites (IPMC) are smart materials that exhibit large deformation in response to small applied voltages, and conversely generate detectable electrical signals in response to mechanical deformations. The study of IPMC materials is a rich field of research, and an interesting intersection of material science, electrochemistry, continuum mechanics, and thermodynamics. Due to their electromechanical and mechanoelectrical transduction capabilities, IPMCs find many applications in robotics, soft robotics, artificial muscles, and biomimetics. This study aims to investigate the dominating physical phenomena that underly the actuation and sensing behavior of IPMC materials. This analysis is made possible by developing a new, hyperelastic …

Patient-Specific Finite Element Analysis For Mandibular Fracture Fixation, Ethan Snyder

UNLV Theses, Dissertations, Professional Papers, and Capstones

This thesis proposes an approach for Finite Element Analysis (FEA) of mandibular fracture fixation. Using a Computerized Tomography (CT) scan of mandible obtained from a specific person, the material characteristics, density and modulus of elasticity, were determined from a set of discrete points within the mandible that are 1mm spaced based on the Hounsfield Units of these points. The mandible geometry was sectioned to simulate a fracture. Muscle and mastication forces were added to replicate post-surgery loading. Using a standard linear miniplate, this material model was compared with two commonly used mandibular cortical shell bone models: isotropic and orthotropic. A …

Healthy Aging In Place: An Integrated Smart Home Using Alexa-Compatible Technology, Tyler Kryst

UNLV Theses, Dissertations, Professional Papers, and Capstones

The purpose of this research was to address current healthcare concerns among the aging population. Around the globe, the average life expectancy is projected to continue increasing resulting in a higher prevalence of age-related disease. With the ever-increasing capabilities of modern technology, it is necessary to apply this technology to increase the health and safety of older adults. This work had three objectives. The first objective was the establishment of an integrated smart home aimed at creating a healthy aging-in-place environment through the use of Alexa. The second objective was the development and integration of a completely custom health device …

Sonic Boom Loudness Reduction Through Localized Supersonic Aircraft Equivalent-Area Changes, Troy A. Abraham

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The NASA University Leadership Initiative (ULI) titled “Adaptive Aerostructures for Revolutionary Civil Supersonic Transportation” looks to study the feasibility of distributed structural adaptivity on a supersonic aircraft for maintaining acceptable en-route sonic boom loudness during overland flight. The ULI includes a team of industry and university partners that are working together to develop and implement the systems necessary to accomplish this goal.

The Utah State University Aerolab is a member of this ULI team and has been tasked with developing and using low-fidelity supersonic aerodynamic and sonic boom predictions tools to rapidly study the effects of localized geometry changes on …

Computational Fluid Dynamics Benchmark Validation Experiment Of Plenum-To-Plenum Flow Through Vertical Heated Parallel Channels, Austin W. Parker

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The next generation of nuclear power plants will have higher efficiency and improved safety, among other benefits; one attractive option is the high temperature gas reactor. An ability to predict the physics that occur within the reactor under normal conditions and accident scenarios is necessary before it receives regulatory licensing for use. The flow through a high temperature gas reactor involves complex interactions of heat transfer, fluids, and solids.

One method for simulating complex fluid dynamics is called Computational Fluid Dynamics. These simulations have already been used to predict the complex fluid flows found in high temperature gas reactors. Predicting …

Modeling, Simulation And Optimization Of Nuclear Hybrid Energy Systems Using Openmodelica And Raven, Stephen Michael Hills

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Nuclear hybrid energy systems (NHES) are a viable option to combine renewable energy sources, such as wind, with a less fluctuating energy source. Given recent development and their inherent safer and modular design, small modular reactors (SMRs), which are smaller versions of a nuclear reactor, can play an instrumental role in complementing renewables and supporting carbon-free power sectors in the coming decades. With increasing population and demand for clean water, Freeze desalination (FD), which uses freezing to separate water from salt, is a possible way to produce clean water while converting excess power from a SMR into stored thermal energy …

Mixed Mode Crack Propagation In Iliac Bone, E. Baesu, Dm. Iliescu, Bv. Radoiu, S. Halichidis

Department of Mechanical and Materials Engineering: Faculty Publications

Bone is a complex material that can be regarded as an anisotropic elastic composite material. The problem of crack propagation in hu- man bone is analyzed by using a generalization of the maximum tensile stress criterion (MTS). The results concern the critical stress for crack propagation and the direction of the crack path in Iliac bone.

Senior Design Capstone: Using An Engineering Design Process To Create A Sawzall Wobble Fixture For Milwaukee Tools, Tyler Moore

Honors Theses

The overall objective of this design project was to successfully design a fixture to expedite the repairs of Sawzalls at the Milwaukee Tools repairs facility in Greenwood, Mississippi. This project was executed in accordance with guidelines set forth by the Senior Capstone Design class at the University of Mississippi as well as the quality engineers sponsoring the project at Milwaukee Tools. The fixture was created utilizing an engineering design process with the goal of allowing technicians to press two Sawzall wobbles onto an angled Sawzall wobble shaft using an arbor press with just one press. By beginning with a straightforward …

Husky Hand: A Low-Cost Electro-Mechanical Prosthetic Arm For The Underprivileged, Adam Robert

Thinking Matters Symposium

A continuation of a low-cost prosthetic upper limb prototype design which was investigated in EGN 301. The prosthetic is specifically designed for the needs and requirements of under privileged individuals in the Dominican Republic with upper limb amputations. The project focuses on the creation of an open-source computer aided prosthetic hand/arm model. The design allows consumer-grade fused filament fabrication (FFF) 3-D printers to be used. The improved design allows for the integration of the PQ-12 linear actuator for grasp and finger control. This simplifies the assembly, while, also reducing the size and mass of the whole unit. Producing a low-cost …

Nitinol Robotic Arm, Brandon Cousino, Connor Sweatt

Thinking Matters Symposium

The goal of our project is to create a remotely controlled robotic arm using a nickel-titanium alloy (Nitinol) that exhibits “shape memory” tendencies and a 9-lumen tube. The arm must be able to move in all for directions (forward, left, right, backwards) with the control of a joystick and return to an upright position upon halting user input (thus requiring a two-way shape memory ability). The final product must operate without any unwanted twisting of the arm, crosstalk between the different nitinol wires due to heating, and be easily manufacturable. Easy replacement of the arm from the main mechanism is …

Sedan Performance/Economy Rear Diffuser, Jacob Boucher Koris

Thinking Matters Symposium

This project consists of designing in SolidWorks a model of the performance/fuel economy diffuser. The design is modeled with an Ahmed body (recommended shape for CFD testing vehicles) and the diffuser will be applied to the bottom of the rear bumper of the car. After this is done the model will be imported into ANSYS for CFD testing. Testing entails importing the model, then creating a mesh around the model, and then setting up the program to run analysis for calculating the coefficient of drag. Then building this SolidWorks model as a full working prototype for actual road-testing purposes. With …

A Critical Review On The Development Of Ionic Liquids-Based Nanofluids As Heat Transfer Fluids For Solar Thermal Energy, Titan C. Paul, Amitav Tikadar, Rajib Mahamud, Azzam S. Salman, A.K.M. Monjur Morshed, Jamil A. Khan

Faculty Publications

In recent years, solar thermal energy (STE) has attracted energy researchers because of its higher efficacy compared to the photovoltaic solar cell. STE is one of the forms of solar energy whereby heat is transferred via a secondary medium called heat transfer fluids (HTFs). Therefore, the overall performance of STE depends on the thermophysical properties and thermal performance of the HTFs. Traditional HTFs suffer from low decomposition temperature, high melting point, and higher vapor pressure. To overcome these limitations, researchers have recently begun working on new HTFs for STE. Ionic liquids (ILs) are considered as a potential candidate for the …