Mechanical Engineering Commons^™

Developing General Purpose Apps To Automate Image Analysis Of Wave-Augmented-Varicose-Explosion Atomization And Other Multi-Phase Interfacial Flows, Ethan Newkirk

Senior Honors Theses

Atomization involves disrupting a flow of contiguous liquid into small droplets ranging from one submicron to several hundred microns (micrometers) in diameter through the processes of exerting sufficient forces that disrupt the retaining surface tensions of the liquid. Understanding this phenomenon requires high-speed imaging from physical models or rigorous multiphase computational fluid dynamics models. We produce a MATLAB application that utilizes various methods of image analysis to quickly analyze and store mathematical data from detailed image analyses. We present a user with numerous tools and capabilities that provide results that deviate from 1.8% to 8.9% of the original image sequence …

Transfer-Learning-Enhanced Regression Generative Adversarial Networks For Optimal Evtol Takeoff Trajectory Prediction, Shuan Tai Yeh, Xiaosong Du

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Electric vertical takeoff and landing (eVTOL) aircraft represent a crucial aviation technology to transform future transportation systems. The unique characteristics of eVTOL aircraft include reduced noise, low pollutant emission, efficient operating cost, and flexible maneuverability, which in the meantime pose critical challenges to advanced power retention techniques. Thus, optimal takeoff trajectory design is essential due to immense power demands during eVTOL takeoffs. Conventional design optimizations, however, adopt high-fidelity simulation models in an iterative manner resulting in a computationally intensive mechanism. In this work, we implement a surrogate-enabled inverse mapping optimization architecture, i.e., directly predicting optimal designs from design requirements (including …

Development, Modeling, Identification, And Control Of Tilt-Rotor Evtol Aircraft, Clayton T. Spencer

All Graduate Theses and Dissertations, Fall 2023 to Present

This thesis includes the development, modeling, identification, and control of an electric-Vertical-Take-Off-and-Landing (eVTOL) aircraft with tiltable rotors. The front two rotors have tilting capability for transition flight from vertical-take-off to forward-level flight. This work details the development of an eVTOL aircraft and the selection of sub components such as electric motors, batteries, and controllers. After the aircraft build, mathematical model is derived to describe the motion of the aircraft. Unknown parameters in the mathematical model are identified using a Least-Squares-regression (LSR) method that can handle parameter constraints. This is done using real flight data collected from the aircraft. Lastly, this …

On-Demand Fabrication Of Piezoelectric Sensors For In-Space Structural Health Monitoring, Amanda White, Isaac Little, Anastasiya Artyuk, Nicholas Mckibben, Fereshteh Rajabi Kouchi, Claire Chen, David Estrada, Zhangxian Deng

Mechanical and Biomedical Engineering Faculty Publications and Presentations

Inflatable structures, promising for future deep space exploration missions, are vulnerable to damage from micrometeoroid and orbital debris impacts. Polyvinylidene fluoride-trifluoroethylene (PVDF-trFE) is a flexible, biocompatible, and chemical-resistant material capable of detecting impact forces due to its piezoelectric properties. This study used a state-of-the-art material extrusion system that has been validated for in-space manufacturing, to facilitate fast-prototyping of consistent and uniform PVDF-trFE films. By systematically investigating ink synthesis, printer settings, and post-processing conditions, this research established a comprehensive understanding of the process-structure-property relationship of printed PVDF-trFE. Consequently, this study consistently achieved the printing of PVDF-trFE films with a thickness of …

Study Of Electrospun Nanocomposite Nanofiber Nonwoven Mats With Precursor Solutions Prepared By Ultrasonic Processing, Stephanie Tussey

All Dissertations

Understanding the complexity of changes in a polymer solution through the addition of nanoparticles and the process used to prepare the solutions is vitally important to obtain desirable characteristics of electrospun nanofibers such as degree of crystallinity, morphological, thermal and mechanical properties. Although there have been significant efforts in this research area, a more in-depth understanding on how nanoparticles can affect the formation of polymeric structures during electrospinning is still needed to ensure overall quality and performance of the nonwoven material. The present study aimed to specifically explore the relationship between solution processing method, nanoparticle volume fraction, and solution properties …

Comparative Analysis Of The Effects Of Post Processing On The Flexural Fatigue Endurance Of Additively Manufactured Ti-6al-4v, Cristian Banuelos

Open Access Theses & Dissertations

This study delves into analyzing the effects of various machining techniques on the flexural fatigue life of Ti-6Al-4V L-PBF specimens. The fatigue life and fracture behavior of specimens subjected to milling, grinding, polishing, and abrasive media blasting were compared. The findings reveal significant differences in the fatigue resistance between machined and non-machined parts. This study contributes to the understanding of the effects of post-processing on the durability of L-PBF manufactured components, offering insights for enhancing their application in critical aerospace and biomedical applications.

Relations Between Printability And Rheology In A Ceramic Paste Extrusion Process, Nicholas Durand

Open Access Theses & Dissertations

Ceramic additive manufacturing (AM) uses the same fundamentals as material extrusion (MEX) that utilizes polymers or resins for printing applications. Ceramic AM uses the same process of slicing an STL file to determine a toolpath for the printer that will facilitate material deposition to manufacture full parts; ceramic AM also provides a low-cost advantage when compared to processes that require high powered lasers for melting metal powders or heated nozzles used for dispensing thermoplastics. Despite having the similar design freedom and ability for rapid prototyping that other printing methods benefit from with the addition of low cost, ceramic AM has …

Prediction Modeling Of Foreign Object Impact Debris On Aircraft Through Digital Engineering, Luis Eduardo Rodriguez

Open Access Theses & Dissertations

The contribution of the research made is derived into two sections. The first topic discusses the prediction modeling of Foreign Object debris (FOd) impact on aircraft structures through the use of digital engineering. The program used in this project is Ansys Explicit Dynamics to evaluate the stress and strain caused by the initial conditions of flight trajectory and impact created from FOd found inside of aircraft structures. The prediction modeling consists of creating a repetition of simulations with different FOds to evaluate the damage created to subsystems of the wing bay such as the fuel system and internal structures. The …

Bottling Automation System, Dylanie Tippit

Honors College Theses

This report details the complete design of an automated bottling system. Each bottle is 5.97 centimeters tall and has an outer diameter of 3.81 centimeters. The goal of the project is to successfully fill and cap twelve bottles in under three and a half minutes. The system will have two conveyors in series, a water dispenser, an electrolyte dispenser, capping station, Human Machine Interface (HMI) and Allen Bradley programmable logic controller (PLC). The water and electrolyte dispenser will have two ball valves in series, with the desired amount of volume to dispense the designated liquid. The capping station will be …

A Manufacturing-To-Response Pathway For Manufacturing Optimization Of Carbon Fiber Reinforced Polymer Composite Structures, Madhura Limaye

All Dissertations

Over the past decade, there has been an increased adoption of thermoplastic and thermoset based continuous carbon fiber reinforced polymer (CFRP) composites for structural applications in several industries. Among the different manufacturing methods, thermoforming process for thermoplastic based continuous CFRP’s offer a major advantage in reducing cycle times for large scale productions. Similarly, out-of-autoclave curing process for thermoset based continuous CFRP’s using heated tooling enables production of large composite structures. However, these manufacturing processes can have a significant impact on the structural performance of parts by inducing undesirable effects. These effects include inhomogeneous fiber orientations, thickness variations, and residual stresses …

Oscillations Of Capillary Surfaces With Volume And Edge Effects, Dingqian Ding

All Dissertations

Capillary surfaces are defined by an interface endowed with surface tension that is partially supported by a solid substrate and are susceptible to oscillations reflecting a balance between fluid inertia and the restorative force of surface tension. The wave dynamics strongly depend upon volume change within the domain and edge effects through the boundary conditions applied at the contact-line formed at the liquid-gas-solid interface, while the spatial wave structure conforms to the geometry of the capillary surface. This dissertation develops mathematical models to address these effects for several canonical capillary surfaces, which are organized into two parts that are focused …

Heat Sink Integrating Phase Change Materials (Pcms) For Cooling High Power Electronic Devices, Mohammad Sameer Qasem

Theses

This research explores the numerical analysis of phase change materials (PCMs) heat sinks, focusing on high heat flux dissipation applications, e.g. electronics cooling. Both 2D and 3D numerical models using gallium and paraffin RT31 as PCMs are considered within a heat sink design framework featuring a rectangular cavity and dual opposing vertical copper walls serving as fins to dissipate heat from the hot sink base that receives heat from the heat source. The inclusion of a Triply Periodic Minimal Surface (TPMS) ‘Primitive’ structure as an in-fill thermal conductivity enhancer (TCE) in the case of the gallium heat sink, and a …

Emulsion Stability, Rheological Properties, And Combustion Characteristics Of Water-Jojoba Biofuel Emulsion, Ihab Mohamed Helal

Theses

This thesis comprehensively investigates the stability, rheological properties, and engine performance implications of Water in Jojoba Biodiesel (WJBD) emulsion. The research delves into multiple aspects, including the influence of diverse surfactants and water concentrations on emulsion stability. It also yields valuable insights into the development of stable water in jojoba biodiesel emulsions, specifically tailored for diesel engines. These insights contribute significantly to the body of knowledge of positioning emulsion fuels as viable alternative to traditional diesel fuels. The anticipated benefits include notable reductions in emissions, improvement in combustion efficiency, and lower production cost. Importantly, this study underscores the critical importance …

Blade Design And Validation Of Hydrokinetic Turbine To Harvest Water Current Energy, Setare Sadeqi

LSU New Orleans Theses and Dissertations

The innovative aspect of this research lies in the careful integration of cutting-edge technologies throughout the entire process of designing, fabricating, and testing the carbon fiber propeller for the 3-bladed horizontal axis ocean current turbine (OCT). SolidWorks software played a pivotal role in the initial design phase, enabling a meticulous and precise modeling of the propeller's geometry. The utilization of SolidWorks allowed for a detailed exploration of various design parameters, ensuring that the propeller's structure and form were optimized for performance in ocean current conditions. Moving beyond the realm of virtual design, the choice of carbon fiber as the fabrication …

The Second-Order Features Adjoint Sensitivity Analysis Methodology For Response-Coupled Forward/Adjoint Linear Systems (2nd-Fasam-L): Mathematical Framework And Illustrative Application To An Energy System, Dan Gabriel Cacuci

Faculty Publications

The Second-Order Features Adjoint Sensitivity Analysis Methodology for Response-Coupled Forward/Adjoint Linear Systems (abbreviated as “2nd-FASAM-L”), presented in this work, enables the most efficient computation of exactly obtained mathematical expressions of first- and second-order sensitivities of a generic system response with respect to the functions (“features”) of model parameters. Subsequently, the first- and second-order sensitivities with respect to the model’s uncertain parameters, boundaries, and internal interfaces are obtained analytically and exactly, without needing large-scale computations. Within the 2nd-FASAM-L methodology, the number of large-scale computations is proportional to the number of model features (defined as functions of model parameters), as opposed to …

Characterizing The Molecular And Cellular Changes Of Senescent Cells Induced By Diverse Stressors In 2d And 3d Microenvironments, Apoorva Chauhan

UNLV Theses, Dissertations, Professional Papers, and Capstones

Aging is a risk factor for myriad diseases and is often associated with the accumulation of senescent cells. Cellular senescence, a process of irreversible cell cycle arrest, is associated with various changes in cellular morphology and function. While senescence will occur naturally in a time-dependent manner, it can be prematurely induced by various extrinsic and intrinsic factors. Most senescence studies model cell behavior in two-dimensional (2D) microenvironments; however, these models are not physiologically relevant. In this study, the effects of naturally occurring reactive oxygen species (ROS) hydrogen peroxide (H2O2) and commonly used chemotherapy drugs, doxorubicin and palbociclib, on cellular senescence …

Sliding Markov Decision Processes For Dynamic Task Planning On Uncrewed Aerial Vehicles, Trent Wiens

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Mission and flight planning problems for uncrewed aircraft systems (UASs) are typically large and complex in space and computational requirements. With enough time and computing resources, some of these problems may be solvable offline and then executed during flight. In dynamic or uncertain environments, however, the mission may require online adaptation and replanning. In this work, we will discuss methods of creating MDPs for online applications, and a method of using a sliding resolution and receding horizon approach to build and solve Markov Decision Processes (MDPs) in practical planing applications for UASs. In this strategy, called a Sliding Markov Decision …

Development Of A Multi-Use Modular Microfluidic Platform Using 3d Printing, Carson Emeigh

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Microfluidic lab-on-a-chip (LoC) technology has driven numerous innovations due to their ability to perform laboratory-scale experiments on a single chip using microchannels. Although LoC technology has been innovative, it still suffers from limitations related to its fabrication and design flexibility. Typical LoC fabrication, with photolithography, is time consuming, expensive, and inflexible. To overcome the limitations of LoC devices, modular microfluidic platforms have been developed where multiple microfluidic modules, each with a specific function or group of functions, can be combined on a single platform. Modular microfluidics have overcome some of the limitations of LoC devices, but currently, their fabrication is …

Investigative Research On Design Parameters And Criticality Models For Microreactors, Cameron Jensen

UNLV Theses, Dissertations, Professional Papers, and Capstones

With increased energy demand and the desire to reduce reliance on fossil fuels, nuclear power will need to play a prominent role in achieving carbon-free energy independence. Large nuclear reactors are necessary to meet this objective. However, they are expensive and take a long time to build. For remote locations (e.g., military bases) and smaller communities, large nuclear reactors would not be feasible or cost effective. Small reactors (microreactors) can fill this necessary gap. These reactors would be factory-built, delivered quickly, and operated with high intrinsic levels of safety. With microreactors still in conceptual and testing states, there is a …

Evaluation, Rating, And Numerical Modeling Of A Shock Mitigation Seat For High-Speed Craft Based On Laboratory Single Impact Testing, Darren Benn

UNLV Theses, Dissertations, Professional Papers, and Capstones

High-speed craft (HSC) are utilized in military and para-military maneuvers that are usually conducted in harsh environments. The Special Warfare Combatant-craft Crewmen (SWCC), a sub-unit of the United States Naval Special Warfare Command (NAVSOC), use an advanced HSC, known as the Combatant Craft Assault, to conduct coastal patrol and interdiction, and for infiltration and exfiltration of Navy SEALs. The United States Coast Guard, and the Drug Enforcement Agency (DEA), employ HSC for maritime patrol and to pursue ‘go-fast’ boats operated by contraband runners. In most of these intense applications, the mode of operation of the HSC results in planing. Planing …

Experiment Development And Validation Of A Granular Jamming Robotic Gripper, Jacob R. Dowd

UNLV Theses, Dissertations, Professional Papers, and Capstones

A granular jamming gripper (GJG) is widely known as a Universal Gripper because of the wide range of objects that it can grasp and the simplicity of control, design, and manufacturing. Despite multitude of research improving the GJG, here, we focus on the base version of the GJG and attempt to glean the range of objects that it may reliably grasp. Despite the limited range of objects, which were a sphere, rectangular prism, and cylinder, we gleaned geometric properties as it relates to successful and unsuccessful grasping. This was based on the two types of testing: push and pull testing …

Predicting The Response Of An Underactuated, 3d Printed Prosthetic Hand, Lucas Gallup

UNLV Theses, Dissertations, Professional Papers, and Capstones

The continuing need for hand prostheses has led to incredible developments in this area. However, due to the cost of the most sophisticated models, it is vital to develop simpler, low-cost, underactuated prostheses that can be produced rapidly. 3D printing is an important tool to achieve this goal. In particular, the 3D printed Flexy-Hand 2 has been one of the most common low-cost designs. A key feature of the Flexy-Hand 2 is its use of tendons and thermoplastic polyurethane (TPU) for joints that are strong and flexible. TPUs, however, lack a thorough understanding of their mechanical behavior, which makes it …

Performance Effects Of Dissociated Hydrogen In Nuclear Thermal Propulsion Engines, Richard Adam Gorrell

UNLV Theses, Dissertations, Professional Papers, and Capstones

Nuclear thermal propulsion (NTP) research considers hydrogen dissociation as negligible to design and analysis of propulsion engines. This study reintroduces chemically reacting flow to NTP engine analysis for investigation of the dissociation effect on engine performance. A first-principles approach observes the basic chemical mechanism and reaction within the high-speed, high-temperature NTP flow to baseline expected atomic hydrogen levels and validate equilibrium. A surface reaction study looks into hydrogen absorption through dissociation and its effect on the boundary layer, and bulk flow. For total performance, the resulting dissociated flow is analyzed through nozzle expansion and performance metrics calculated.

All historic reactor …

Effect Of Pre-Heating On Residual Stresses And Deformation In Laser-Based Directed Energy Deposition Repair: A Comparative Analysis, Usman Tariq, Sung Heng Wu, Muhammad Arif Mahmood, Michael M. Woodworth, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Laser-Directed Energy Deposition (DED), a Metal Additive Manufacturing Method, is Renowned for its Role in Repairing Parts, Particularly When Replacement Costs Are Prohibitive. Ensuring that Repaired Parts Avoid Residual Stresses and Deformation is Crucial for Maintaining Functional Integrity. This Study Conducts Experimental and Numerical Analyses on Trapezoidal Shape Repairs, Validating Both the Thermal and Mechanical Models with Experimental Results. Additionally, the Study Presents a Methodology for Creating a Toolpath Applicable to Both the DED Process and Abaqus CAE Software. the Findings Indicate that Employing a Pre-Heating Strategy Can Reduce Residual Stresses by over 70% Compared to No Pre-Heating. However, Pre-Heating …

Novel Designs Of Soft Tactile Sensor And Robot Finger Manipulator Based On Optical Fibers., Seokyoung Han

Electronic Theses and Dissertations

Robotic manipulation is one of the main types of automated labor that humans want to achieve in order to free ourselves from mundane and hazardous tasks. The range of realizations could be very broad, from massive industrial robots to highly advanced medical devices for human healthcare. Given the critical nature of these application spaces, they require robust, safe, and most of all versatile designs. In that direction, one of the most interesting topics is the anthropomorphic robotic manipulator. Since it is inspired by human hands’ function and structure, it is able to achieve the aforementioned system requirements. However, the perfect …

Electrokinetic Particle Trapping Performance Of Conductive Nanofiber Mats In Microfluidic Wells., Jacob Hunter West

Electronic Theses and Dissertations

The frequency dependence of electrokinetic particle trapping using large-area (>mm²) conductive carbon nanofiber (CNF) mat electrodes is investigated. The fibers provide nanoscale geometric features for the generation of high electric field gradients, which is necessary for particle trapping via dielectrophoresis (DEP). A device was fabricated with an array of microfluidic wells for repeated experiments; each well included a CNF mat electrode opposing an aluminum electrode. Fluorescent microspheres (1 µm) were trapped at various electric field frequencies between 30 kHz – 1 MHz. Digital images of each well were analyzed to quantify particle trapping. DEP trapping by the …

Development, 3d Printing, And Sintering Of Aluminum-Magnesium Alloy Pastes For In-Space Manufacturing Applications, Fatou Ndiaye

Electronic Theses and Dissertations

This study explores the additive manufacturing process of paste printing, sintering, and de-binding for fabricating aluminum-magnesium alloy components. The paste formulation involved combining aluminum powder with varying magnesium concentrations, utilizing acrylic polyol, solvent, and plasticizer to create a homogeneous mixture. Printing parameters were optimized to ensure continuous pressure for improved extrusion. Sintering conditions involved incremental temperature increases with nitrogen flow to remove solvents. Density measurements, tensile tests, and shrinkage calculations were conducted to assess part quality post-sintering. The study revealed significant improvements in part quality with 5 wt.% magnesium incorporation within aluminum, although density and tensile strength fell short of …

Barocaloric Heat Pumps Based On Soft Materials., Naveen Weerasekera

Electronic Theses and Dissertations

Solid-state refrigeration offers a promising alternative to traditional vapor compression systems that are relatively inefficient, unreliable, and have a high global warming potential. Various solid-state cooling technologies, including those based on electrocaloric, magnetocaloric, and elastocaloric effects have been investigated in the recent past. However, concerns regarding their efficiency, scalability and cost remain. Refrigeration and heat pump technologies based on the barocaloric effect (temperature/entropy change due to hydrostatic pressure) hold great promise but have received comparatively less attention. Barocaloric heating/cooling based on low cost, compressible soft materials with large barocaloric response have the potential to pave the way for efficient, scalable, …

Mechanical Properties And Microstructure Of Multi-Materials Fabricated Through A Combination Of Lpbf And Ded Additive Manufacturing Techniques, Christopher J. Bettencourt

All Graduate Theses and Dissertations, Fall 2023 to Present

This research explores the use of different metals combined through 3D-printing to enhance the performance of materials, with a focus on making heat exchangers more cost-effective for renewable energy. The goal is to replace a costly high-temperature alloy with a more affordable low-temperature alloy, using metal additive manufacturing for its benefits such as less material waste, faster production, reduced weight, and the ability to print entire assemblies in one go. The study delves into a unique combination of two 3D-printing techniques, Directed Energy Deposition and Laser Powder-Bed Fusion, to create a multi-material composed of stainless steel 316L and a nickel-based …

Test And Evaluation Model For Midwater Docking Of Autonomous Underwater Vehicles, Parker Baillon

Theses and Dissertations

This research created a Test and Evaluation (T&E) model for midwater Autonomous Underwater Vehicle (AUV) capture. The creation of this model will allow for a better assessment of the feasibility of midwater AUV capture. To achieve this, the T&E model was exposed to various flow conditions to assess stability. Capturing an AUV in midwater, the area below the wave-affected zone to the sea floor, has many benefits for an AUV and its mission. AUVs basing missions from a midwater dock will not be affected by wave motions. A midwater dock can be transported to any mission site and deployed with …