Structural Materials Commons^™

Low-Cost, Low-Weight Test Rig Design For A Laboratory-Scale Twin Rotor Wind Turbine, Ahmed Ayoub, Ahmed Elzeedy, Mahmoud Elkordy, Eslam Ayad, Mohamed Waleed, Amira Elkodama, Amr Ismaiel

Future Engineering Journal

Multi-Rotor Wind Turbine (MRWT) has been proven advantageous over Single-Rotor Wind Turbine (SRWT) in many aspects. In order to study the performance of MRWT over SRWT, this work presents a low-cost and low-weight design for a test rig for laboratory-scale wind turbine configurations. The configurations under study are a single-rotor, and a twin-rotor of the same size with a diameter of 30 cm. Aerodynamic loads have been calculated using the Blade Element Momentum (BEM) method, then the loads were used for stress analysis over the test rig proposed. The test rig is designed on Solidworks and the aerodynamic and inertial …

Effectiveness Of Clay Nanotube Blended Coating Materials For Thermal Insulation, Hawa Hashm

Doctoral Dissertations

Studies conducted by the U.S. Department of Energy reported that heating and cooling systems use nearly 60% of the total energy consumed in a building, while approximately 31% of that energy loss occurs through the improperly insulated floor, walls, and ceiling. Hot summers or severely cold weather can make these problems worse. The passing of conditioned air through these building materials is a substantial source of energy loss, which has driven significant investigation into new environmentally friendly, sustainable, and cost-effective solutions. The main objective of the research was to experimentally evaluate the thermal conductivity of paints blended with halloysite nanotubes …

Experimental Evidence That Shear Bands In Metallic Glasses Nucleate Like Cracks, Alan A. Long, Wendelin Wright, Xiaojun Gu, Anna Thackray, Mayisha Nakib, Jonathan T. Uhl, Karin A. Dahmen

Faculty Journal Articles

Highly time-resolved mechanical measurements, modeling, and simulations show that large shear bands in bulk metallic glasses nucleate in a manner similar to cracks. When small slips reach a nucleation size, the dynamics changes and the shear band rapidly grows to span the entire sample. Smaller nucleation sizes imply lower ductility. Ductility can be increased by increasing the nucleation size relative to the maximum (“cutoff”) shear band size at the upper edge of the power law scaling range of their size distribution. This can be achieved in three ways: (1) by increasing the nucleation size beyond this cutoff size of the …

Bio-Based Food Packaging Material For Intelligent Food Packaging Applications For Chicken Fillets, Kalpani Y. Perera, Amit K. Jaiswal, Swarma Jaiswal, Shubham Sharma

Articles

Bionanocomposite packaging is made up of bio- based materials that have high performance activity and are ecologically sustainable alternatives to packaging made of synthetic polymers. Intelligent packaging retains track of the state of the food and the environment in which it is stored, and communicates relevant changes to the consumer through visualization or other methods. The aim of this study was to develop a bionanocomposite intelligent packaging material by utilising sodium alginate, gelatin, nanoclay and curcumin. Sodium alginate, gelatin film incorporated with Curcumin (Cur), and Nanoclay (NC) in various concentrations (0% W/V, 0.5% W/V, 1% W/V and 1. 5% W/V) …

Influence Of Defects On In-Plane Dynamic Properties Of Hexagonal Ligament Chiral Structures, Ning An, Xunwen Su, Dongmei Zhu, Mileta M. Tomovic

Engineering Technology Faculty Publications

Although the six-ligament chiral structure has many unique properties, due to its special structure, the stress concentration is prone to defects. In addition, additive manufacturing is also prone to defects. This paper studies the effect of defects, which is helpful for the better application of the six-ligament chiral structure. Several new six-ligament chiral structures with random and concentrated defects were designed to explore the effects of the defects on the in-plane dynamic properties. The structures were studied with the finite element ANSYS/LSDYNA numerical simulation and experimental methods. According to the defect-free six-ligament chiral structures exhibiting different deformation modes at different …

Removal Of Selenium And Heavy Metals From Coal Combustion Residuals Wastewater Using Surface Modified Iron Based Media, Madan Tandukar, Alex Korff, Andrew Vincent, Chris Hardin

World of Coal Ash Proceedings

No abstract provided.

Initial Exploration Of Reduced Gyrations For Arkansas Asphalt Mix Designs, Jocie L. Baker

Graduate Theses and Dissertations

The most common distresses in asphalt pavement are cracking and rutting. These distresses plague almost every asphalt roadway in the world. Finding ways to mitigate these distresses will improve the performance of asphalt pavements. One way to combat the premature cracking of asphalt in the field is to ensure there is enough asphalt binder within the mix. This will help the flexibility of the asphalt undergoing large loads and deformation. However, it is widely accepted that mix designs across the country lack the appropriate amount of asphalt binder in their mixes, causing dry mix designs that are subject to cracking …

Crack Control And Bond Performance Of Alternative Coated Reinforcements In Concrete, Sachin Sreedhara

All Dissertations

Concrete cracking in structures is a ubiquitous problem which can lead to the deterioration of the structure. Other than affecting the strength aspect of a structure, cracking impacts the serviceability criteria as well. Although cracking phenomenon in any structure is highly inevitable, it has to be minimized in order to maintain a structure’s life effectively. Cracking in reinforced concrete structures is related to the bond strength developed between the bar and the concrete. It also depends on an ability of the bar to resist the stresses due to shrinkage to minimize the crack. Another important aspect is the resistance offered …

Xps And Ipe Determination Of Band Offsets Of Germanium Based Materials, Justin Michael Rudie

Graduate Theses and Dissertations

Germanium tin and silicon germanium tin are group IV semiconductor alloys that have gained significant interest in recent years for their potential use in optoelectrical devices. While silicon and germanium are indirect bandgap materials on their own, alloying them with tin in sufficient quantities leads to a transition to direct bandgap alloys. Direct gap performance opens the door for efficient light emitting and detecting devices fabricated entirely on group IV materials that are compatible with the industry standard CMOS manufacturing techniques. Germanium tin and silicon germanium tin have bandgaps that respond to light in the mid to near infrared spectrum …

Bbt Acoustic Alternative Top Bracing Cadd Data Set-Norev-2022jun28, Bill Hemphill

STEM Guitar Project’s BBT Acoustic Kit

This electronic document file set consists of an overview presentation (PDF-formatted) file and companion video (MP4) and CADD files (DWG & DXF) for laser cutting the ETSU-developed alternate top bracing designs and marking templates for the STEM Guitar Project’s BBT (OM-sized) standard acoustic guitar kit. The three (3) alternative BBT top bracing designs in this release are
(a) a one-piece base for the standard kit's (Martin-style) bracing,
(b) 277 Ladder-style bracing, and
(c) an X-braced fan-style bracing similar to traditional European or so-called 'classical' acoustic guitars.

The CADD data set for each of the three (3) top bracing designs includes …

Mechanical Properties Of Engineering Cement-Based Materials Containing Modified Shape Memory Alloy Fiber, Song Mengfan

International Conference on Durability of Concrete Structures

在这项研究中，提出了一种 SMA 纤维的表面改性方法，以改善水泥基复合材料中纤维的界面性能。SMA 纤维涂有 SiO ₂，预计会与 Ca(OH) _2反应由水泥水化形成，减少了薄弱区的可能性，并在纤维-基体界面处形成了更致密的微观结构。采用扫描电子显微镜 (SEM)、能量色散光谱 (EDS) 和红外吸收光谱 (IR) 对表面改性后的 SMA 纤维进行表征。此外，还进行了抗弯强度试验、抗压强度试验和四点弯曲试验，以评价宏观尺度上界面力学性能的增强情况。实验结果表明，包覆的 SiO ₂，导致改性 SMA 纤维-水泥界面处的 CSH 凝胶量增加和孔隙率降低。改性后的SMA纤维与水泥基体之间的紧密粘附有利于建立更强的界面结合力，有利于提高抗弯强度、抗压强度、四点抗弯强度和挠度。抗弯强度、抗压强度、四点抗弯强度和挠度均在28d时显着增加。结果支持了所提出的表面改性方法适用于 SMA 纤维以提高其在工程水泥基材料中的增强效率的结论。

Mechanical Properties And Microstructure Of High Strength Lc3 Pastes With Varying Limestone/Calcined Clay Ratios And Different Curing Conditions, Yemin Dong

International Conference on Durability of Concrete Structures

研究（抗施工蒸馏）石石和石榴石在淀粉胶系统（即0标准和低水印）下的水胶系统（即0标准和低水墨）X射线比、水量值水量-电子背基相关研究.61.25 .25.25.25.0.25.25.25.25.25.0.25.25.25.25.25.1.25.7.25.0.0.0.0.0.0.0.0.0.0.0.0.0.0.1.25.1.25.25.1.25.1.25.1.25.1.25.1.25.1 .25.1.25.1.25.1.25.1.25.1.25.0.0.0.0.0.0.0.00.0.0.1.25.1.25.1.25.1.25.1.25.0.0.0.00.0.0.0.0.0.0.0.0.0.0.0.0.0.00.0 .00.0.00.X射线比值、水量-电子显微镜相关研究测量值。早期的水泥水化程度小水的压合含煤量，降低了水泥石的。因此，需要采用合适的钙铝内容和体系以提高碳系统的性能。

Study On The Effect Of Fly Ash On The Properties Of Potassium Magnesium Phosphate Cement, Bo Pang

International Conference on Durability of Concrete Structures

In this paper, the effect of fly ash on the setting time and mechanical properties of potassium magnesium phosphate cement is studied. The early hydration process of potassium magnesium phosphate cement was studied by TAM-Air, and the hydration products were analyzed by XRD. The results show that fly ash can effectively prolong the setting time and the compressive strength of the cement paste was decreased; The addition of fly ash would not change the phase composition of the hydration products of the potassium magnesium phosphate cement, which affect the hydration process, the amount of the hydration products and the degree …

Study On Hydration Properties Of Grinded Tuff-Cement Cementitious Material System, Hao Wang

International Conference on Durability of Concrete Structures

The chemical composition and microscopic morphology characteristics of grinded tuff(GT) and fly ash(FA) were compared and analyzed in the paper. The chemical bound water content and hydration heat were tested for investigating the hydration properties of grinded tuff-cement cementitious material system (GTCS) and fly ash-cement cementitious material system (FACS). The results shown that, the chemical composition of GT was similar with that of FA, however the loss on ignition of the GT was obviously higher than FA. The microstructure of the GT particles was polygonal and irregular, while the microstructure of FA particles were mostly smooth spheres. The hydrated heat …

Investigation On The Properties Of Calcium Sulfoaluminate Cement Waterproof Repair Mortar Modified With Ethylene-Vinyl Acetate Powder, Dong Dong

International Conference on Durability of Concrete Structures

本文采用乙烯-醋酸乙烯酯（EVA）粉体和CSA水泥制备了防水修复砂浆，并对其水化和性能进行了研究。结果表明，EVA粉体延长了凝固时间，提高了防水修补砂浆的流动性，使其在实际工程中更容易应用。EVA粉提高了防水修复砂浆的不渗透性，降低了吸水性。虽然EVA粉降低了防水修补砂浆的抗弯强度和抗压强度，但它仍然符合JC/T 2381-2016标准对刚性修复砂浆的要求。EVA粉体降低了防水修复砂浆的收缩率，改善了界面过渡区和拉伸粘接强度、弯曲粘接强度等粘接性能。EVA粉末抑制CSA水泥的水合作用6 h，在3 d水化年龄时抑制作用消失。

Shrinkage And Durability Of Cement Mortars With Recycled Aggregates, Wencui Yang

International Conference on Durability of Concrete Structures

In recent years, the rapid growth of economy and urbanization process in China resulted in the massive construction and demolition wastes (C&DW). The reutilization of C&DW as recycled aggregates (RA) fully or partially to replace natural aggregates is an effective way to solve the environmental and economic problems caused by C&DW. The properties of cement mortars could be influenced by recycled fine aggregates due to their high absorption and the quantity of fine particles. This paper presents the main results of the research to explore the effect of recycled aggregate (RA) on shrinkage and durability properties of masonry mortars. Four …

Investigation On Structural Heritability And Durability Of High Sulfate Resistance Portland Cement Mortar Modified By Aluminum Salt, Jun Xu

International Conference on Durability of Concrete Structures

The essential hydration and hardened properties of high sulfate resistance Portland cement paste/mortar were investigated with Al₂(SO₄)₃ as admixture. Experiment results showed that that the addition of Al₂(SO₄)₃ promoted the hydration of HSRP cement pastes, and the hydration rate accelerated with the increase of the addition amount. The mechanical properties and chloride diffusion coefficient of cement mortar were obviously improved with 0.25% Al₂(SO₄)₃ addition . For instance, the compressive strength of AS0.25 cement mortars was 24.8% higher than AS0 samples and the chloride ion migration …

Production Of Low-Cost Self-Consolidating Concrete (Scc) Using Manufactured Aggregates, Rabab Raydan, Farah Chamseddine, Ali Jahami, Oussama Baalbaki, Jamal Khatib, Adel Elkordi

BAU Journal - Science and Technology

Limitations to the sources of aggregates and the unavailability of sand is becoming a problematic issue for concrete production. A novel technology of manufactured aggregates can produce well graded round aggregates that can substitute natural aggregates while maintaining the same characteristics needed and preserving the resources. Self-Consolidating Concrete (SCC) using manufactured aggregates is assessed in this experimental work to understand the variability of workability properties and mechanical properties with the changes in w/c ratio and percentages of Coarse Aggregates and Manufactured Sand to Natural Sand in order to choose the best mixture that satisfies an adequate overall performance. Targeting compressive …

Evaluating The Effects Of Granulated Rubber And Glass Fibers In Polymer Concrete As A Structural Material For Wafer Grinding Machines, Kevin Gabriel Kuehn, Philip Randall Streeter

Materials Engineering

Polymer concrete is a composite material used to replace cast iron and steel in wafer grinding machines for vibration damping. During the grinding and lapping processes of manufacturing silicon wafers, excessive vibrations may cause subsurface damage which requires additional polishing and reduces yield. Nine compositions containing various levels of granulated rubber and glass fibers were manufactured. CRM WRF-10 granulated rubber was examined at 0%, 5%, and 10% and Corning Cem-Fil glass fibers were added at 0%, 0.5%, and 1% by weight. Smooth-On EpoxAcast 690 epoxy resin was held constant at 16% for each composition. Crushed granite aggregate from Martin Marietta, …

Dynamic Response Of Elastic Two-Story Steel Moment Frame Scaled Structure Equipped With Viscous Dampers, Garrett L. Barker, Alexander L. Poirier

Architectural Engineering

The authors of this report are Architectural Engineering undergraduate students at California Polytechnic State University, San Luis Obispo. Damping is a complex, experimentally derived value that is affected by many structural properties and has a profound effect on the dynamic response of structures. Deducing the inherent damping of a steel moment frame and affecting the damping ratio with viscous dampers are two topics explored in this paper. Dampers are commonly implemented in resilient structures that perform better in a design basis earthquake, reducing the seismic cost and downtime. Undergraduate coursework does not delve into the factors that affect damping and …

Investigation Of The Effects Of Cladding Layers On Longitudinal And Transverse Mechanical Properties In Composite Laminates, Rachel Potratz, Tiffany Foo, Joseph Kamlet

Materials Engineering

The addition of cladding layers to composite laminates is used in industry to improve bond adhesion and the ease of manufacturing. However, there is no public data on the effects of cladding layers on the mechanical properties of composite components. To directly observe how cladding layers affect mechanical properties, four laminates with zero, one, two, and three cladding layers of twill fabric were added symmetrically to a biased core. The mechanical testing performed was tensile, short beam strength, and compression testing in the longitudinal and transverse directions. The measured strengths were related to the longitudinal properties of the core, and …

A Review Of Current Construction Guidelines To Inform The Design Of Rammed Earth Houses In Seismically Active Zones, David Thompson, Charles Augarde, Juan Pablo Osorio

Articles

Sustainability in the materials we use for construction is a prime concern, focusing on reducing the embodied energy and carbon footprints of the materials used. The cement used in concrete products is responsible for a significant proportion of Man's CO2 emissions and its production requires substantial energy input, as do fired clay products. For this reason, products formed from unfired earthen materials are of increasing interest and the current challenges include devising means of robust design for strength and to address durability concerns. One form of earthen construction that employs an in-situ method is rammed earth, and it is a …

Ecological Risk Assessment For Coal Combustion Residuals And Herrington Lake Adjacent To The Kentucky Utilities E.W. Brown Generating Station, Mary Sorensen, Alex Smith, Mark Nielsen

World of Coal Ash Proceedings

No abstract provided.

Epri Research On Groundwater-Surface Water Interactions Near Coal Combustion Product Sites, Bruce Hensel, Jeff Thomas, Tim Towey, Anthony Aufdenkampe

World of Coal Ash Proceedings

No abstract provided.

Cqa - A Common Sense Approach At Becoming The Mvp On Your Next Project, James Price, Michael Fisher, John Metcalf

World of Coal Ash Proceedings

No abstract provided.

Challenges & Pragmatic Solutions For The Design And Construction Of A 300-Acre Ccr Landfill Located In The Southwestern Us - A Case Study, Andy Lucas, Jason Pokorny

World of Coal Ash Proceedings

No abstract provided.

State Of The Practice For Compaction Quality Of Dry Stack Ccr Storage Facilities, Bruce Cunningham, Pavana Vennapusa, David J. White, Robert Eric Hageman

World of Coal Ash Proceedings

No abstract provided.

Groundwater Compliance & Strategy Insights For Ccr Rule Stakeholders, Sheryl Smith, Mark Johnson

World of Coal Ash Proceedings

No abstract provided.

Hybrid Closure Approach: Constructing Bidding Lessons Learned, Brian Harthun, P.E.

World of Coal Ash Proceedings

No abstract provided.

Ccr Landfill Construction & Operation Under Subtitle D, Thomas R. Gredell

World of Coal Ash Proceedings

No abstract provided.