Structural Materials Commons^™

New Type Of Lightweight Aggregate For Use In Structural Concrete, Jamal Khatib, Ali Jahami, Oussama Baalbaki, Adel Elkordi

BAU Journal - Science and Technology

This research studied the utilization of municipal solid waste incineration bottom ash (MSWI-BA) in lightweight coarse aggregate (LWC) production. A special method was followed to prepare the new aggregate to fully replace the normal aggregates (NWA) in concrete. The mechanical properties such as compressive strength, tensile strength, and elasticity modulus were investigated for the LWC concrete. Then, two beams were prepared; one from LWC and the other from NWC. The structural performance of beams made up of lightweight aggregates compared to normal aggregates was investigated. The results showed that this type of aggregates led to a 20% reduction in concrete …

Effects Of Bonding Pressure And Lamina Thickness On Mechanical Properties Of Clt Composed Of Southern Yellow Pine, Cody S. Bates

Theses and Dissertations

This study produced cross-laminated timber panels at a range of four lamina thickness (5/8, 1, 1 1/8, and 1 1/4 inch) and three bonding pressures (50, 125, 200 psi), producing a total of 12 panels for mechanical testing. The goal of this study is to observe how the thickness and pressure trends affect the mechanical properties of CLT. Tests include flatwise bending, flatwise shear, internal-bond, and delamination. Results showed that bending MOE decreases as the panel thickness increases while bonding pressure had no significance. Bending MOR was less significant for the thickness and more significant for pressure compared to the …

A Temporal Analysis Of The Microbiota And Biofouling Development On Artificial Substrates In The Port Everglades Inlet, Florida, Denise Swack

All HCAS Student Capstones, Theses, and Dissertations

A pilot project was deployed in Port Everglades Inlet, Florida that aimed to evaluate the biofilm composing the microbiome on ecologically engineered artificial substrates used to build Coastal Marine Infrastructure. In April of 2017, an Articulated Concrete Block Mattress comprised of an ecological engineered concrete substrate and a standard smooth surface control substrates were compared. This study will provide a profile on the microbiome community on artificial substrates within Port Everglades Inlet on bio-enhancing concrete-based solutions in our Coastal Marine Infrastructure. To study the microbial community, the 16s rRNA technology was used in Illumina’s high-throughput DNA sequencing. Samples were collected …

Shear Strength Of Concrete Beams Made With Belitic Calcium Sulfoaluminate Cement, Caleb W. Chesnut

Graduate Theses and Dissertations

The need for a cleaner alternative to portland cement (PC) concrete has led to increasing interest in alternatives to PC. Structural properties of most of these alternative cements are still an open research topic. One promising alternative cement is belitic calcium sulfoaluminate (BCSA) cement. The study presented in this paper investigated the shear strength, long term compressive strength, and carbonation in BCSA cement and PC concrete beams. A total of twelve eight-foot long beams were made; eight BCSA cement concrete beams and four PC concrete beams to be tested at various ages depending on cement type. Two beams of each …

Mechanical Interfacial Locking And Multiscale Modeling Of Reinforced Thermoplastic Composites For Structural Applications, Anmol Kothari

All Dissertations

The ever-growing pressure of reducing the adverse impact of transportation systems on environment has pushed industries towards fuel-efficient and sustainable solutions. While several approaches have been used to improve fuel efficiency, the light-weighting of structural components has proven broadly effective. In this regard, reinforced thermoplastic composites (RTPC), owing to their high recyclability, higher impact strength and fast cycle times, have become competitive candidates at an industrial scale. However, to implement RTPC toward large scale structural applications several challenges pertaining to material design and manufacturing effects need to be addressed. To this end, a computational study is carried out to address …

Development Of Lambda Factors For Masonry Design With Lightweight Grout, Rumi Shrestha

All Theses

Reduction in structural mass, improvement in thermal performance, and reduction in shrinkage cracking through internal curing are some of the reasons that lightweight (LW) aggregates have been used in structures and pavements for decades. However, lightweight grout is still not permitted for use in reinforced masonry construction by the TMS 402/602-16 code. In order to realize the benefits of lightweight grout in U.S. reinforced masonry construction, a codified procedure for its use is required which must be informed by experimental testing.

This research is a pilot project directed to characterize the performance of LW grout in comparison to normal weight …

Impact Of Exposure On Thin Epoxy Overlay Performance, Abul Fazal Mazumder

Dissertations

Thin epoxy overlays are used for improving the condition and extending the service life of bridge decks. The tensile bond pull-off strength, evaluated as per the ASTM C1583, is used as the performance indicator. A failure in the substrate with a tensile strength of 250 psi or greater is considered acceptable. However, the performance evaluated on in-service bridge decks shows inconsistent results. Laboratory studies by several researchers documented a distinct performance difference when the overlays are exposed to room temperatures in comparison to elevated temperatures. However, the most influential parameters such as concrete surface profile, thermal compatibility between overlay and …

Seaweed Polysaccharide In Food Contact Materials (Active Packaging, Intelligent Packaging, Edible Films, And Coatings), Kalpani Y. Perera, Shubham Sharma, Amit K. Jaiswal, Swarna Jaiswal

Articles

Food contact materials (FCMs) are materials that come in contact with food products such as food packaging which play a significant role in the food quality and safety. Plastic, which is a major food packaging material, harms the eco-system, wildlife, and the environment. As a result, numerous researches have been in progress on alternative polymers, which has similar properties as plastic but is also environmentally friendly (biodegradable). In recent years, the utilization of seaweed polysaccharides has piqued interest due to its biodegradability, non-toxicity, antioxidant capabilities, and excellent film formation ability. However, it has a number of drawbacks such as low …

Tools And Strategies For The Patterning Of Bioactive Molecules And Macromolecules, Daniel J. Valles

Dissertations, Theses, and Capstone Projects

Hypersurface Photolithography (HP) is a printing method for fabricating structures and patterns composed of soft materials bound to solid surfaces and with ~1 micrometer resolution in the x, y, and z dimensions. This platform leverages benign, low intensity light to perform photochemical surface reactions with spatial and temporal control of irradiation, and, as a result, is particularly useful for patterning delicate organic and biological material. In particular, surface- initiated controlled radical polymerizations can be leveraged to create arbitrary polymer and block- copolymer brush patterns. Chapter 1 will review the advances in instrumentation architectures from our group that have made these …

Rapid Annealing Of Perovskite Solar Cell Thin Film Materials Through Intense Pulse Light., Amir Hossein Ghahremani

Electronic Theses and Dissertations

Perovskite solar cells (PSCs) have garnered a great attention due to their rapid efficiency improvement using cheap and solution processable materials that can be adapted for scalable high-speed automated manufacturing. Thin film perovskite photovoltaics (PVs) are typically fabricated in an inert environment, such as nitrogen glovebox, through a set of deposition and annealing steps, each playing a significant role on the power conversion efficiency (PCE), reproducibility, and stability of devices. However, atmospheric processing of PSCs would achieve lucrative commercialization. Therefore, it is necessary to utilize materials and methods that enable successful fabrication of efficient PSCs in the ambient environment. The …

Semi Real-Time Detection Of Subsurface Consolidation Defects During Concrete Curing Stage, Chongsheng Cheng, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Subsurface consolidation defect is a common issue in concrete pavement construction, and the hidden defects often require costly repairs after project delivery. Therefore, being able to identify this type of defect during construction will enable contractor to conduct quick repairs to avoid costly post-construction rework. In this paper a semi real-time detection approach using infrared thermography is introduced. The developed approach utilizes the hydration heat during curing time to identify the subsurface voids based on the regional temperature contrast. Experimental studies were conducted using artificial void-defect in different sizes and depths. The thermographic analysis is employed to locate the void-defects …

Frequency Effect On Peak Pressure Coefficients Using The Narrowband Synthesis Random Flow Generator (Nsrfg) Method, Zayuris Del Carmen Atencio Mojica

Graduate Theses and Dissertations

The collapse of the Tacoma Narrows Bridge in Washington state in 1940 due to high wind forces gave structural engineers notice of the importance of understanding the behavior of wind forces on infrastructure. Wind forces play an important role in the design of buildings and other structures. ASCE 7-16 is the manual used for the design of these buildings and other structures throughout the country. These design criteria have been approved based on research projects involving experimental procedures. For the design of wind loads, ASCE 7-16 uses criteria based on wind tunnel (WT) tests. However, since the development of computing …

Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere

Graduate Theses and Dissertations

Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …

Review: Factors Affecting Composite Laminates Against Lightning Strikes, Aaryan Manoj Nair

Publications and Research

Lightning strike protection (LSP) have recently been a newly developing field particularly with the emergence of graphene thin film integration into carbon fiber composite structures. This technology has a widespread application in airplanes, wind turbines, and other instruments which are susceptible to frequent lightning strikes. Electrical discharge of the instrument in a safe manner is vital for the safety of the passengers (in the case of flights) as well as the integrity of the aircraft structures because of their specific mechanical and structural properties, which are essential for their functioning. The purpose of the study is to fabricate graphene thin …

Investigation Of Membrane Based Processes For Biomedical Applications, Efecan Pakkaner

Graduate Theses and Dissertations

As substantial developments were achieved in nanotechnology and polymer engineering, especially in the last few decades, the use of membranes and membrane-based procedures was found to be expanding into more and more research and development areas; including biological engineering, life sciences and biomedical engineering. Not only have they been the main focus of meaningful research, but they have also been the main pieces of the solutions to very thorny problems encountered within a wide range of applications from microfluidics to water treatment, thanks to their versatility, cost-effectiveness and biocompatibility, when compared to conventional separation techniques. To celebrate and embrace these …

Assessment Of Carbon Dioxide Emission And Its Impact On High-Rise Mixed-Use Buildings In Egypt, Ahmed Salah Hamza

Theses and Dissertations

With Egypt's vision of 2030 focusing on sustainable development with a true emphasis on Carbon Dioxide (CO₂) emission reduction in the newly built cities and high-rise buildings, efforts are exerted on various levels towards accomplishing the vision’s goals. This is achieved through multiple tools and models associated with aiding the reduction of carbon emissions, yet not a clear one was introduced for the mixed-use buildings in Egypt.

Through this work, a significant gap was identified with respect to high-rise buildings carbon emission assessment in Egypt. This was a main driving force for this work in an attempt to …

Enhancement Of Asphalt Performance By Graphene-Based Bitumen Nanocomposites, Sara Moghtadernejad, Ehsan Barjasteh, Ren Nagata, Haia Malabeh

Mineta Transportation Institute

As the State of California continues to grow, demand for enhanced infrastructure such as roadways and highways escalates. In view of the current average highway lifespan of 15–20 years, the improvement of asphalt binders leads to material sustainability by decreasing required maintenance and increasing the lifespan of roadways. In the present investigation, enhancement of asphalt binder properties was achieved by different methods of mixing varying compositions of graphene nanoparticles with an SBS polymer and asphalt binder. Additionally, experimental evaluation and comparison of the rheological and mechanical properties of each specimen is presented. Graphene nanoparticles have attracted great curiosity in the …

Strengthening Of 7175 Aluminum Alloy Through Multi-Step Aging Process, Colin E. Masterson, Ryland W. Jolliffe

Materials Engineering

7175 is a heat-treatable aluminum alloy commonly used in aerospace forgings. This alloy is aged with a multi-step heat treatment. This treatment must balance strength with stress corrosion cracking resistance through a degree of overaging. The team was tasked by Weber Metals to increase the strength of this treatment without sacrificing stress corrosion cracking resistance. Both two-step and retrogression and reaging treatments were tested in experiments to find a heat treatment that could increase the yield and tensile strength by 1-2 ksi while maintaining a minimum electrochemical conductivity equivalence of 38% relative to copper. Two-step aging is the more conventional …

Use Of Biomimicry Design Approach In Constructing Sustainable Resilient Structures (Case Study: Port Of Beirut), Farouk Bader, Marwan Halabi, Hiba Mohsen, Maged Youssef

BAU Journal - Creative Sustainable Development

Resiliency is not the same as sustainability, nor its substitute, but definitely the two concepts complement each other’s. Sustainability is the avoidance of depletion of natural resources to maintain ecological balance whereas resiliency is to recover, adapt and keep going in the face of setbacks. While designing with green approach is important but what will happen to leed points if the building becomes uninhabitable due to disasters, that’s where resiliency comes into play. The 2019 statistics showed that natural disasters accounted for 133 billion dollars losses and manmade ones accounted for other 7 billion in addition to 11,755 people worldwide …

Computational Design Of Nonlinear Stress-Strain Of Isotropic Materials, Askhad M.Polatov, Akhmat M. Ikramov, Daniyarbek Razmukhamedov

Chemical Technology, Control and Management

The article deals with the problems of numerical modeling of nonlinear physical processes of the stress-strain state of structural elements. An elastoplastic medium of a homogeneous solid material is investigated. The results of computational experiments on the study of the process of physically nonlinear deformation of isotropic elements of three-dimensional structures with a system of one- and double-periodic spherical cavities under uniaxial compression are presented. The influence and mutual influence of stress concentrators in the form of spherical cavities, vertically located two cavities and a horizontally located system of two cavities on the deformation of the structure are investigated. Numerical …

Higher-Order Topolectrical Semimetal Realized Via Synthetic Gauge Fields, Xiang Ni, Andrea Alù

Advanced Science Research Center

Classical bosonic systems may be tailored to support topological order and unidirectional edge transport exploiting gauge fields. Here, we theoretically explore how synthetic gauge fields may be used to induce higher-order topological phases and zero-energy boundary states. We demonstrate these principles in two types of three-dimensional topolectrical circuits with synthetic gauge fields threading through their reduced two-dimensional lattices, leading to a half-quantized quadrupole charge within a region of the momentum space. We theoretically show the emergence of nodal line rings and Weyl points in the bulk dispersion, whose projected surfaces and hinges support surface Fermi arcs and flat hinge Fermi …

An Investigation Of Testing Parameters On The Frictional Properties Of Patterned Core-Shell Nanostructures, Colin Phelan

Graduate Theses and Dissertations

Friction tests are a beneficial means to analyze the tribological characteristics and advantages of materials and textured surfaces. However, the selected test parameters can significantly influence the results. This work explores the significance of the friction testing parameters on the frictional performances of core-shell nanostructure-textured surfaces (CSNTSs). Several applied normal loads (10 μN, 100 μN, and 500 μN) and diamond counterface indenter tip radii (1 μm, 5 μm, and 20 μm) were selected for the testing of Al/diamond-like-carbon (DLC) and Al/amorphous silicon (a-Si) CSNTSs. The measured friction values of the CSNTSs were then compared to a matching Al/DLC film and …

Mechanical Behavior Of Cyclo-18 On Nickel And Copper Substrates, Reagan Michael Kraft

Mechanical Engineering Undergraduate Honors Theses

Carbyne, an -hybridized allotrope of carbon, has been the subject of many studies recently due to its incredible mechanical properties and small size. More recently, another -hybridized allotrope known as cyclo-18, has gained interest. In this study, computational molecular dynamics will be used to determine the mechanical properties of cyclo-18. Peeling and shearing tests of the molecule will be conducted on nickel and copper, which are respectively active and less-active transition metals. Additionally, a carbyne chain of equal length will undergo the same tests on the copper substrate to compare the mechanical properties of the two. The results conclude that …

Noise Control In Sorting Conveyors, Eyra Herrera

Mechanical Engineering Undergraduate Honors Theses

E-commerce has increased the necessity of effective material handling equipment in warehouses and distribution centers. Sorter conveyors systems facilitate material handling by providing a reliable and automated system to classify and distribute products in a gentle and rapid manner. With the steady increase of speed in sorter conveyors to satisfy today’s industry demand, some systems have started to produce high noise levels that could potentially affect workers’ health. Since decreasing the speed of these conveyors is not a viable option to decrease noise in sorter equipment, industries have opted to find other ways to apply noise control to their equipment. …

Characterizing High Entropy Alloys For Hypersonic Applications, Katherine Pettus

Mechanical Engineering Undergraduate Honors Theses

In this paper, the properties of a new and broad class of materials, high entropy alloys (HEAs), were investigated and evaluated for hypersonic applications. The plan was to identify candidate hypersonic HEAs and model the high-temperature strength using new advanced material models that account for asymmetry and anisotropy characterized with available test data. After accessing a local database of HEAs and their material properties in collaboration with Dr. Gorsse et al., it was realized the knowledge of HEAs is currently very broad but lacks depth. While hundreds of HEAs have been created and tested, none so far have both sufficient …

Finite Element Analysis Of Impact Resistant Composites Inspired By Peacock Mantis Shrimp, Nandati Shrestha

Thinking Matters Symposium

The fist-like club of the peacock mantis shrimp, a 5-inch marine crustacean, can strike its prey with speed faster than a .22-caliber bullet with an impact force more than 1,000 times its own weight. Although these creatures punch so fast that it even boils the water, they don’t take any damage. This incredible insusceptibility is due to the arrangement of mineralized fiber layers in which each fibrous layer is laid at a slightly rotated angle to form a helicoidal structure that acts as a shock absorber for the club. The goal is to perform a finite element analysis to investigate …

Damage Evolution And High-Rate Response Of High-Strength Concrete Under Triaxial Loading, Brett Williams

Mechanical Engineering Research Theses and Dissertations

The research presented in this study focuses on understanding fundamental mechanisms that drive material response under dynamic loading conditions. The objectives of the research were to: (1) to understand damage initiation and propagation in the bulk geomaterial under a variety of loading conditions and (2) to systematically investigate the strain rate effects on the triaxial compressive response of cementitious materials through the development of an innovative, first of its kind large-diameter (50 mm) triaxial Kolsky bar system.

The triaxial compressive response of high-strength concrete is needed to understand pressure-dependent material behavior, which is important for modeling extreme loading events. However, …

Influence Of Parameters Of Non-Standard Modes Of Heat Treatment On Increasing The Wear Resistance Of Steel Products, Dorob Murotovich Berdiyev Dsn, Abdulaziz Abdullajanovich Yusupov Head Teacher, Ravshan Kobilovich Tashmatov Doctoral Student, Tuychi Nemat Ogli Ibodullayev Assistant, Kabira Erkinovna Qurbonova Head Teacher

Scientific-technical journal

The use of non-standard modes of heat treatment increases the density of dislocations in the crystal structure of the α-phase and increases the wear resistance of carbon, low-alloy steels under various friction conditions, which is comparable to the results when heated to a standard temperature (Ac₃+30÷50 °C). The preliminary extreme heating temperature is determined. After re-quenching at standard temperature and low tempering, the wear resistance of steels under various types of friction increases by up to 40 % compared to standard quenching.

Influence Of Parameters Of Non-Standard Modes Of Heat Treatment On Increasing The Wear Resistance Of Steel Products, Dorob Murotovich Berdiyev Dsn, Abdulaziz Abdullajanovich Yusupov Head Teacher, Ravshan Kobilovich Tashmatov Doctoral Student, Tuychi Nemat Ogli Ibodullayev Assistant, Kabira Erkinovna Qurbonova Head Teacher

Scientific-technical journal

The use of non-standard modes of heat treatment increases the density of dislocations in the crystal structure of the α-phase and increases the wear resistance of carbon, low-alloy steels under various friction conditions, which is comparable to the results when heated to a standard temperature (Ac₃+30÷50 °C). The preliminary extreme heating temperature is determined. After re-quenching at standard temperature and low tempering, the wear resistance of steels under various types of friction increases by up to 40 % compared to standard quenching.

Study Of Laser Based Additive Manufacturing For Titanium And Copper Alloys, Congyuan Zeng

LSU Doctoral Dissertations

Material processing by laser is increasingly applied in industrial applications for its outstanding characteristics, such as localized heating, high efficiency, and high manufacturing precision. In this study, two kinds of laser material processing strategies were investigated, namely laser surface engineering and laser-powder-bed fusion additive manufacturing, with pure titanium and copper alloys as target materials, respectively.

For laser surface engineering related studies, the work includes the investigation of the dynamic interactions between titanium and pure nitrogen or ambient air under transient laser processing conditions. Thanks to the in-situ synchrotron X-ray diffraction tests, the high-temperature reaction steps between titanium and pure nitrogen/ambient …