Structural Materials Commons^™

Research On General Drawing Design Technologies For Cover Culverts In Hunan Province, Peng Xiaoming, Li Yukun, Hu Qiong, Xia Yutao

Journal of China & Foreign Highway

As one of the main structures of highways，a culvert has the characteristics of large quantity and wide range.Affected by design and construction factors，engineering diseases of culverts have been prominent for a long time.With the extensive promotion of the green highway construction concept and the continuous updating of technical standards and design specifications，the original general drawing of culverts fails to meet the needs of the sustainable and healthy development of highway construction under the new situation.Hunan Provincial Communications Planning，Survey & Design Institute has conducted extensive and in-depth investigation and research on the key technologies of highway culvert design and prepared a …

Design And Installation Technology Of Hanging Basket For Long‑Span Concrete Girder Cable‑Stayed Bridge, Zeng Xianliu, Pang Jianguo, Chen Cheng

Journal of China & Foreign Highway

The main bridge of Zhungeer Yellow River Super Major Bridge is a （160+440+160） m double tower double cable plane full floating system concrete grider cable-stayed bridge.The main beam is a 28.4m wide double box prestressed concrete structure.It was constructed by cantilever pouring with a front fulcrum hanging basket.The maximum weight of the cantilever pouring section is 5 800 kN.To ensure the integral rigidity of the hanging basket，the hanging basket bearing platform adopted the steel box girder structure.The long and large components were connected by high-strength bolts made in sections to facilitate the transportation and installation of the hanging basket.The hanging …

Key Technology For Design Of Composition Section Of Hybrid Girder Cable‐Stayed Bridge, Tian Bo, Song Lubing

Journal of China & Foreign Highway

The main bridge of the Yibin Nanxi (Xianyuan) Yangtze River Bridge adopts an asymmetric hybrid girder cable-stayed design with a 572 m main span. The main span and the north-side span utilize hybrid girders, while the south-side span uses a concrete girder. A steel-concrete composite section is introduced between the south-side span and the main span. This paper explores multiple schemes for the location and key structural design of the steel-concrete composite section, prioritizing a full-section rib connection with a pressure-bearing shear transfer transition structure. The structural rationality and construction feasibility were verified through on-site static model tests, failure model …

A Review Of Current Construction Guidelines To Inform The Design Of Rammed Earth Houses In Seismically Active Zones, David Thompson, Charles Augarde, Juan Pablo Osorio

Articles

Sustainability in the materials we use for construction is a prime concern, focusing on reducing the embodied energy and carbon footprints of the materials used. The cement used in concrete products is responsible for a significant proportion of Man's CO2 emissions and its production requires substantial energy input, as do fired clay products. For this reason, products formed from unfired earthen materials are of increasing interest and the current challenges include devising means of robust design for strength and to address durability concerns. One form of earthen construction that employs an in-situ method is rammed earth, and it is a …

Tabletop Mechanical Tester, Jamie Dombroski, Brian English, Richard Leffler, Andrew Shirk

Williams Honors College, Honors Research Projects

The need for hands-on and face-to-face experiences in the engineering classroom is very great. The equations, principles, and concepts can all be learned, but without the visual and tactile application, these don’t always sink in or become concrete. A small-scale tensile test machine was designed, sourced, manufactured, and tested for the purpose of being applied in classroom settings to provide this experience to engineering students. Extensive research was performed concerning tensile machines on the market, the essential elements of which are the load cell, grips, crosshead, extensometer, motor, and frame. The raw materials for the frame were purchased and drawings …

Development Of A Mix Design Adjustment Method For Fiber Reinforced Concrete And Super High Performance Concrete Based On Excess Paste, Joe Malloy

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The main objective of this study was to develop a mix design adjustment method for Fiber Reinforced Concrete (FRC) that would maintain appropriate workability while improving hardened concrete performance. A literature review was conducted to examine existing methods for adjusting mix designs to account for fiber introduction. It was found that while increasing fine aggregate and cement paste content can make up for lost workability with the addition of fibers, no rational mix design adjustment method is available. Reference mix designs from the Nevada Department of Transportation and the Nebraska Department of Transportation were used, and this study focused on …

Autojack - Hydraulic Powertrain System, Tyce Vu

All Undergraduate Projects

A primary problem for mechanics and automotive enthusiasts is the risk associated with lifting and securing a vehicle with conventional jack stands. Often times, improper jack-stand installation results in the vehicle collapsing unexpectedly, causing injury and/or death. This problem can be minimized through the application of a newly re-designed vehicle lifting system. The conventional method for lifting cars is time consuming and can be unsafe in many circumstances. A better, safer, and more efficient lift design was needed; the AutoJack. The approach of the AutoJack design was entirely focused on the safety of lifting a vehicle. Safety was improved by …

Design Survey Of Laminated Composite I-Beam, Mrinmoy Saha

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

Composite I-beams are popular for high-strength low-weight applications. Learning the macro-mechanics and designing the composite I-beam properly are necessary. In this report, a design overview of the composite I-beam is discussed which is based on classical lamination theory where it includes the homogenization approach, the plane stress assumption and the Kirchhoff hypothesis. Using these assumptions, a method was developed to come up with the effective material properties of a beam. Formulas to calculate maximum deflection and maximum bending stress and shear stress and the stress concentration at the connection of web-flange are discussed which describe ways for designing and manufacturing …

3d Printing – An Insider’S Perspective, Siddharth Sah

The Transdisciplinary STEAM+ Journal

The 3D printing market globally is still at its infancy, - or some might argue that there isn’t really a market yet. The knowledge of 3D printing design is still largely limited to engineering design – not product design. At MakeWhale, we are constantly pushing the boundaries of the application of 3D printing technology to consumer products resulting in a beautiful mix of technology and art.

Corrosion Of Steel In Concrete And Its Prevention In Aggressive Chloride-Bearing Environments, Luca Bertolini, Maddalena Carsana, Matteo Gastaldi, Federica Lollini, Elena Redaelli

International Conference on Durability of Concrete Structures

This keynote paper deals with the durability of reinforced concrete (RC) structures exposed to aggressive environments characterized by high concentration of chloride ions, namely, marine environments or the use of de-icing salts. The mechanism of chloride-induced corrosion of steel in concrete is introduced, and its influence on the service life of RC structures is analyzed. Factors affecting the time to corrosion initiation are described with regard to both concrete properties and environmental exposure conditions. Design approaches available for achieving durability targets associated with the design service life are analyzed, focusing on studies carried out by the authors in recent years …

Shearing Shed Design, W L. Mcgarry, D. A. Young, M. Butler

Journal of the Department of Agriculture, Western Australia, Series 4

PLANNING the layout of a shearing shed requires a good deal of thought to ensure its maximum working efficiency.

If the contemplated structure is to serve the dual purpose of storage-shearing shed, it is better to plan a shearing shed that can be used for storage, rather than a storage shed with a view to its utilisation as a shearing shed.