Structural Materials Commons^™

Effect Of Curing Duration On Bridge Deck Concrete Performance, Zhaniya Omarova

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

This study evaluates the influence of curing duration on the performance of bridge deck concrete and investigates the feasibility of reducing curing periods without compromising structural and durability properties. Two concrete mixtures, a standard Nebraska Department of Transportation (NDOT) bridge deck mix (47BD) and an optimized reduced-cement-content mix (O47BD-R100), were evaluated under multiple curing durations Fresh, early-age, mechanical, durability, and shrinkage properties were assessed to characterize the effect of curing on concrete behavior. Internal relative humidity and temperature were monitored using embedded sensors to investigate moisture diffusion and its role in shrinkage development for lab specimens and full-scale slabs.

Results …

Effect Of Antioxidant Additives And Recycling Agents On Performance Of Asphalt Binders And Mixtures, Phase I, Nitish R. Bastola, Mahdieh Khedmati, Hamzeh Haghshenas, Jamilla Teixeira

Nebraska Department of Transportation: Research Reports

The use of reclaimed asphalt pavement (RAP) in asphalt mixtures has notably increased in recent times. Nevertheless, the inherent stiff and aged characteristics of RAP materials have consistently raised concerns regarding cracking performance. The use of recycling agents (RAs) has gained popularity in recent years since they can effectively modify the engineering properties of the aged asphalt binder. Besides that, the combination of RA with antioxidant (AO) additives has shown promise in enhancing the long-term performance of RAP mixtures. This research aims to investigate the effect of various RAs and one AO additive on performance of asphalt binders and high-RAP …

Structural Performance And Resiliency Of Reinforced Concrete Bridge Pier Columns, Multi-Column Piers, And Bridge Systems Subjected To Multiple Hazards – Fire, Collision, And Air Blast, Qusai Abdulkarim Alomari

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

Given their close proximity to traffic and improper employment of protective systems, bridges and bridge piers are vulnerable to multi-hazard events triggered by vehicle collisions coupled with correlated and cascading events, such as explosions and fires. Despite recent catastrophic incidents that have highlighted the profound consequences of these extreme demands, including substantial damage, adverse economic impact, and loss of life, there has been a notable lack of research investigating the performance of bridges and bridge structural components under the aforementioned multi-hazards. Furthermore, current bridge design codes do not address these events assuming that, after these destructive events, replacement of the …

Toward Low Carbon Footprint And Lightweight Masonry Alkali-Activated Material, Zina Ebrahim, Mohammad Mastali, Marc Maguire

Durham School of Architectural Engineering and Construction: Faculty Publications

The portland cement concrete industry and the masonry industry are undergoing changes in response to skilled labor shortages and concerns over climate and pollution. There may be interest from parts of the industry in lower carbon footprint and lightweight masonry products. Toward this aim, the use of hemp shiv--the woody core of the hemp plant--in alkali-activated concrete was investigated herein and shown to have a wide range of impacts on the hardened state characteristics of a material suitable for structural concrete masonry units (CMUs) in accordance with ASTM C90 requirements. Hemp shiv is well known for its use in hempcrete, …

Assessment Of Bridge Pier Response To Fire, Vehicle Impact, And Air Blast, Chen Fang, Qusai Alomari, Daniel G. Linzell

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Highway bridges exposed to intentional or unintentional fire followed by combined vehicle impact and air blast are at risk of significant damage and, possibly, collapse. Limited studies examining the complex effects of these extreme demands on bridge support elements and parametrizing their response and damage are found in the open literature. Research that is presented is part of an ongoing numerical investigation examining round, multi-column, reinforced concrete (RC), bridge pier behavior subject to multi-hazard scenarios involving fire, vehicle impact, and air blast. Detailed nonlinear finite element analysis models of single columns and multi-column piers supported by a pile foundation system …

Semi Real-Time Detection Of Subsurface Consolidation Defects During Concrete Curing Stage, Chongsheng Cheng, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Subsurface consolidation defect is a common issue in concrete pavement construction, and the hidden defects often require costly repairs after project delivery. Therefore, being able to identify this type of defect during construction will enable contractor to conduct quick repairs to avoid costly post-construction rework. In this paper a semi real-time detection approach using infrared thermography is introduced. The developed approach utilizes the hydration heat during curing time to identify the subsurface voids based on the regional temperature contrast. Experimental studies were conducted using artificial void-defect in different sizes and depths. The thermographic analysis is employed to locate the void-defects …

Automatic Delamination Segmentation For Bridge Deck Based On Encoder-Decoder Deep Learning Through Uav-Based Thermography, Chongsheng Cheng, Zhexiong Shang, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Concrete deck delamination often demonstrates strong variations in size, shape, and temperature distribution under the influences of outdoor weather conditions. The strong variations create challenges for pure analytical solutions in infrared image segmentation of delaminated areas. The recently developed supervised deep learning approach demonstrated the potentials in achieving automatic segmentation of RGB images. However, its effectiveness in segmenting thermal images remains under-explored. The main challenge lies in the development of specific models and the generation of a large range of labeled infrared images for training. To address this challenge, a customized deep learning model based on encoder-decoder architecture is proposed …

Development Of A Mix Design Adjustment Method For Fiber Reinforced Concrete And Super High Performance Concrete Based On Excess Paste, Joe Malloy

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The main objective of this study was to develop a mix design adjustment method for Fiber Reinforced Concrete (FRC) that would maintain appropriate workability while improving hardened concrete performance. A literature review was conducted to examine existing methods for adjusting mix designs to account for fiber introduction. It was found that while increasing fine aggregate and cement paste content can make up for lost workability with the addition of fibers, no rational mix design adjustment method is available. Reference mix designs from the Nevada Department of Transportation and the Nebraska Department of Transportation were used, and this study focused on …

The Application Of Gray-Scale Level-Set Method In Segmentation Of Concrete Deck Delamination Using Infrared Images, Chongsheng Cheng, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Conventional nondestructive delamination detection of concrete pavements through thermography is often based on temperature contrasts between delaminated and sound areas. Non-uniform backgrounds caused by the environmental conditions are often challenging for contrast-based methods to robustly differentiate the delaminated areas from the sound areas. Instead of focusing on the temperature contrast, this study proposes a temperature gradient-based level set method (LSM) to detect boundaries for delamination segmentations. A modified edge indicator function is developed to represent the normalized temperature gradient of a thermal image. The experimental study was conducted to evaluate its applicability and stability for boundary detection in terms of …

Electrically Conductive Concrete Mix For Electromagnetic (Em) Ground Plane, Christopher Tuan, Lim Nguyen

Department of Civil and Environmental Engineering: Faculty Publications

Conductive concrete mixtures are described that are configured to reflect, for instance, EM waves propagating from an EM pulser onto the conductive concrete mixture forming a ground plane, rather than absorb or dissipate the electromagnetic energy. The conductive concrete mixtures include cement, aggregate, water, metallic conductive material, and conductive carbon particles.

Bridge Deck Delamination Segmentation Based On Aerial Thermography Through Regularized Grayscale Morphological Reconstruction And Gradient Statistics, Chongsheng Cheng, Zhexiong Shang, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Environmental and surface texture-induced temperature variation across the bridge deck is a major source of errors in delamination detection through thermography. This type of external noise poises a significant challenge for conventional quantitative methods such as global thresholding and k-means clustering. An iterative top-down approach is proposed for delamination segmentation based on grayscale morphological reconstruction. A weight-decay function was used to regularize the reconstruction for regional maxima extraction. The mean and coefficient of variation of temperature gradient estimated from delamination boundaries were used for discrimination. The proposed approach was tested on a lab experiment and an in-service bridge deck. The …

Thermographic Laplacian-Pyramid Filtering To Enhance Delamination Detection In Concrete Structure, Chongsheng Cheng, Ri Na, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Despite decades of efforts using thermography to detect delamination in concrete decks, challenges still exist in removing environmental noise from thermal images. The performance of conventional temperature-contrast approaches can be significantly limited by environment-induced non-uniform temperature distribution across imaging spaces. Time-series based methodologies were found robust to spatial temperature non-uniformity but requires extended period to collect data. A new empirical image filtering method is introduced in this paper to enhance the delamination detection using blob detection method that originated from computer vison. The proposed method employs a Laplacian of Gaussian filter to achieve multi-scale detection of abnormal thermal patterns by …

Viscoelastic Analysis And Fatigue Characterization Of Bituminous Materials In Two Length Scales Under The Influence Of Aging, Santosh Reddy Kommidi

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Fatigue cracking in asphalt concrete (AC) is of immense importance to pavement design and analysis because it is one of the most important forms of distress that can lead to structural failure in pavement. Once started, these types of cracks can be combined with other environmental factors leading to detrimental effects such as faster rates of pavement deterioration and shortened pavement life and functionality.

Currently AASHTO TP101, also known as linear amplitude sweep (LAS) specification, is being widely used to evaluate the ability of an asphalt binder to resist fatigue. The LAS method, although mechanistic in its approach, has certain …

Fabrication And Study Of The Structure And Magnetism Of Rare-Earth Free Nanoclusters, Bhaskar Das

Department of Physics and Astronomy: Dissertations, Theses, and Student Research

No abstract provided.

Negahban Group Report: Saw-Tooth Shear Response Of Aged Poly(Methyl Methacrylate) (Pmma), Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

Results for isothermal saw-tooth shear loading experiments conducted on annealed and oven-cooled poly(methyl methacrylate) (PMMA) at temperatures between 50^oC and 140^oC. The experiments were conducted 1996.

Optimizing Chemical & Rheological Properties Of Rejuvenated Bitumen, Dominic Nguyen, Hamzeh Haghshenas Fatmehsari, Santosh Kommidi, Yong-Rak Kim

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Bitumen has long been a material used in the construction of roadways, yet new pavement only consists of low fractions of recycled materials due to poor compatibility of aged bitumen and new materials. Thus, rejuvenators, chemical additives, have been used in an attempt to re-balance the chemical composition and restore the physical properties of aged bitumen back to its virgin state. A fundamental understanding of how one particular rejuvenator, soybean oil, revitalizes bitumen was investigated using a multi-scale approach.

Fourier-transform infrared spectroscopy (FTIR) was used to determine the changes in chemical properties of pure and rejuvenated virgin and aged samples. …

Structural Reliability Analysis Of Corroded Steel Girder Bridge, Mohammed Shaalan Al Badran

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The natural aging, environmental impact, and appropriate design are certainly playing a serious role in safety of the bridges function. The functional safety of bridge constitutes a prime element of the transportation system serving commuters, passengers and freight. According to Federal Highway Administration, the steel bridges share represents a large amount of the United States’ bridges. In last century, the collapse of both the Silver Bridge at Point Pleasant, West Virginia over the Ohio River on December 15, 1967 and over the Mianus River Bridge in Connecticut on June 28, 1983 showed that steel corrosion has been the leading reason …

Prediction Of The Thermomechanical Behavior Of Particle-Reinforced Metal Matrix Composites, Yi Hua, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

The objective of this paper was to predict the thermomechanical behavior of 2080 aluminum alloy reinforced with SiC particles using the Mori–Tanaka theory combined with the finite element method. The influences of particle volume fraction, stiffness, aspect ratio and orientation were examined in terms of effective Young’s modulus, Poisson’s ratio and coefficient of thermal expansion (CTE) of the composite. The microstructure induced local stress and strain field was obtained through the numerical models of the representative volume element. Results suggested that particle volume fraction had significant impact on the effective Young’s modulus, Poisson’s ratio and CTE of the composite. Stiffer …

The Influence Of Heterogeneous Meninges On The Brain Mechanics Under Primary Blast Loading, Linxia Gu, Mehdi S. Chafi, Shailesh Ganpule, Namas Chandra

Department of Mechanical and Materials Engineering: Faculty Publications

In the modeling of brain mechanics subjected to primary blast waves, there is currently no consensus on how many biological components to be used in the brain–meninges–skull complex, and what type of constitutive models to be adopted. The objective of this study is to determine the role of layered meninges in damping the dynamic response of the brain under primary blast loadings. A composite structures composed of eight solid relevant layers (including the pia, cerebrospinal fluid (CSF), dura maters) with different mechanical properties are constructed to mimic the heterogeneous human head. A hyper-viscoelastic material model is developed to better represent …

Peridynamic Model For Dynamic Fracture In Unidirectional Fiber-Reinforced Composites, Wenke Hu, Youn Doh Ha, Florin Bobaru

Department of Mechanical and Materials Engineering: Faculty Publications

We propose a computational method for a homogenized peridynamics description of fiber-reinforced composites and we use it to simulate dynamic brittle fracture and damage in these materials. With this model we analyze the dynamic effects induced by different types of dynamic loading on the fracture and damage behavior of unidirectional fiber-reinforced composites. In contrast to the results expected from quasi-static loading, the simulations show that dynamic conditions can lead to co-existence of and transitions between fracture modes; matrix shattering can happen before a splitting crack propagates. We observe matrix–fiber splitting fracture, matrix cracking, and crack migration in the matrix, including …

Studies Of Dynamic Crack Propagation And Crack Branching With Peridynamics, Youn Doh Ha, Florin Bobaru

Department of Engineering Mechanics: Faculty Publications

In this paper we discuss the peridynamic analysis of dynamic crack branching in brittle materials and show results of convergence studies under uniform grid refinement (m-convergence) and under decreasing the peridynamic horizon (δ-convergence). Comparisons with experimentally obtained values are made for the crack-tip propagation speed with three different peridynamic horizons.We also analyze the influence of the particular shape of themicro-modulus function and of different materials (Duran 50 glass and soda-lime glass) on the crack propagation behavior. We show that the peridynamic solution for this problem captures all the main features, observed experimentally, of dynamic crack propagation and branching, as well …

Multiscale Modeling Of Impact On Heterogeneous Viscoelastic Solids With Evolving Microcracks, Flavio V. Souza

Department of Engineering Mechanics: Dissertations, Theses, and Student Research

Multiscale computational techniques play a major role in solving problems related to viscoelastic composite materials due to the complexities inherent to these materials. In the present work, a numerical procedure for multiscale modeling of impact on heterogeneous viscoelastic solids containing evolving microcracks is proposed in which the (global scale) homogenized viscoelastic incremental constitutive equations have the same form as the local scale viscoelastic incremental constitutive equations, but the homogenized tangent constitutive tensor and the homogenized incremental history dependent stress tensor depend on the amount of damage accumulated at the local scale. Furthermore, the developed technique allows the computation of the …

Aircraft Quality Casting Standards, Robert Katz, Robert Bolin , Depositor

Robert Katz Publications

These standards are to be used in connection with the Handbook for Instructions for Aircraft Designers, 8^th Edition …

In the radiography of aircraft castings, markings appearing on the film may be attributed to either the condition of the castings examined, or to some details of the radiographic process entirely unrelated to the quality of the castings, These latter patterns must be recognized and related to the radiographic process so that sound castings will not be unnecessarily rejected. Radiographs must be carefully compared with the surface irregularities of the casting they represent before an attempt is made to …