Structural Materials Commons^™

Creation Of The 2-Way Cross Laminated Timber Subroutine For Computing Dynamic Analysis Parameters, Joseph Freitas

Architectural Engineering

This document will describe the inputs, methodology, and outputs for the CLT 2-way subroutine for cases with and without openings recently added to a proprietary structural analysis software. For the sake of simplicity, most of the discussion will be focused on cases without openings from here on out, as the verification process for a novel method for cases with openings is still in progress. The CLT 2-way module calculates multi-point resistance functions for panels without openings by automating the procedure outlined in an industry-standard structural design manual. The subroutine also finds the appropriate dynamic response factors, kinetic load multipliers, mass, …

Dealuminated Metakaolin In Supplementary Cementitious Material And Alkali-Activated Systems: A Review, Amany G. Micheal Prof., Mostafa Adel Elsebaei Eng., Maria Mavroulidou Prof., Maria Centeno Assoc. Prof., Rabee Shamass Senior Lec., Ottavia Rispolio Mrs.

Architectural Engineering

This paper presents a comprehensive review of dealuminated metakaolin (DK), a hazardous industrial by-product generated by the aluminium sulphate (alum) industry and evaluates its potential as a component in cementitious systems for the partial or full replacement of Portland cement (PC). Positioned within the context of waste valorisation in concrete, the review aims to establish a critical understanding of DK formation, properties, and reactivity, particularly its pozzolanic potential, to assess its suitability for use as a supplementary cementitious material (SCM), or as a precursor in alkali-activated cement (AAC) systems for concrete. A systematic methodology is used to extract and synthesise …

Polypropylene As Partial Fine Aggregate Substitute In Concrete, Samuel E. Royston, Chrisitan G. Achkar, Nicholas B. Tabarez

Architectural Engineering

The objective of this project is to discover a structurally effective method in repurposing recyclable plastic waste through its partial substitution for traditional fine aggregate in concrete.

Results obtained from analysis indicate a 25 percent compressive strength reduction with polypropylene at a 10 percent partial substitution for total sand content. This material successfully performed as an alternative, presenting a ductile mode of failure.

Three material alternatives - polypropylene, polyethylene, and rubber - were substituted for a percentage of sand. These materials underwent concrete cylinder crushing tests to determine their ultimate crushing strength, with the intent of identifying the most effective …

Testing Of Recycled Polypropylene As A Viable Structural Material (Quarter 2), Isabella Jimenez-Melendrez, Katherine Timbes, Jocelyn Embleton, Tauni Dela Cruz, Zyra Kingston, Emily Byrd, Jacob Stinger

Architectural Engineering

5.25 trillion plastic particles have been found in the oceans each year, 3 million water bottles are consumed each hour, and one million plastic bags are used each minute in the United States of America (Williams). The vast majority of conventional plastics such as polyethylene, polypropylene, polystyrene, and more, are non-biodegradable (Tokiwa). To make matters worse, 70% of this non-biodegradable plastic is discarded into landfills and inevitably makes its way into the environment (Williams,). Plastic products have become vital to the United States economy due to their many uses in the construction, packaging, transportation, and health care industries. However, this …

Precious Plastics - Plastic Brick Machine Fabrication, Timothy Ukaobasi Kanu, Evi Paraskevi Troulis

Architectural Engineering

The goal of this research is to determine the structural parameters of the recycled plastic polypropylene when molded into bricks resembling CMU blocks. To accomplish this, three mechanisms had to be assembled: the shredder, the injector, and the 1x1 mold. A tensile and compression test were to be performed on the plastic brick, and the values would be used to compare the tensile and compressive strength of PP plastic bricks, as well as their modulus of elasticity and stress vs. Strain performance. These values would be analyzed to determine whether it would be feasible to build an entire plastic wall. …

Dynamic Response Of Elastic Two-Story Steel Moment Frame Scaled Structure Equipped With Viscous Dampers, Garrett L. Barker, Alexander L. Poirier

Architectural Engineering

The authors of this report are Architectural Engineering undergraduate students at California Polytechnic State University, San Luis Obispo. Damping is a complex, experimentally derived value that is affected by many structural properties and has a profound effect on the dynamic response of structures. Deducing the inherent damping of a steel moment frame and affecting the damping ratio with viscous dampers are two topics explored in this paper. Dampers are commonly implemented in resilient structures that perform better in a design basis earthquake, reducing the seismic cost and downtime. Undergraduate coursework does not delve into the factors that affect damping and …

Analysis Of Burning Wood In The Transient State And The Application To Structural Design, Roberta Veliz, Kimberly Guzman

Architectural Engineering

Determining the extent of the contribution of exposed timber on compartment fire dynamics in open floor plans is a complex process. Designers traditionally used compartmentalization design methods which create spaces where flashover is likely, given the fuel load and ventilation conditions. However, due to the large geometric dimensions and spread of fuel, fires in open floor plans are more likely to remain as localized or traveling fires. As such, an understanding of not only ignition potential but also flame spread is critical to characterizing the contribution of exposed timber. An integral step in characterizing the potential contribution is through an …