Structural Materials Commons^™

Influence Of The Substrate Characteristics On The Bond Behavior Of Pbo Frcm-Concrete Joints, Tommaso D'Antino, Lesley H. Sneed, Christian Carloni, Carlo Pellegrino

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Fiber Reinforced Cementitious Matrix (FRCM) composites can be employed as a valid alternative to Fiber Reinforced Polymers (FRP) composites for strengthening existing reinforced concrete (RC) structures. The weakness of FRCM-concrete joints has been reported to be at the matrix-fiber interface rather than within the concrete substrate, as is usually reported in the case of FRP-concrete joints. The experimental investigations regarding FRCM strengthening available in the literature have been performed by applying the FRCM composite onto a surface that was treated before the application, usually by grinding or sandblasting. However, the role of the substrate characteristics on the failure mechanism of …

Evolution Of Non-Metallic Inclusions In Foundry Steel Casting Processes, Marc Harris, Von Richards, Ronald J. O'Malley, Semen Naumovich Lekakh

Materials Science and Engineering Faculty Research & Creative Works

The evolution of nonmetallic inclusions was examined for 4320 steel at an industrial steel foundry. The steel was followed from electric arc furnace melting through ladle refining to final casting. Timed sampling was performed at all stages of the process. Samples were analyzed using an automated SEM/EDS system. The overall evolution of oxide inclusions in terms of nucleation, growth, and flotation during liquid processing was studied using area fraction and average diameter. Chemical composition evolution was observed using a joint ternary plotting tool developed under this program. It was found that the use of zirconium as an addition for nitrogen/oxygen …

Process Development For Compression Molding Of Hybrid Continuous And Chopped Carbon Fiber Prepreg For Production Of Functionally Graded Composite Structures, Corinne Marie Warnock

Master's Theses

Composite materials offer a high strength-to-weight ratio and directional load bearing capabilities. Compression molding of composite materials yields a superior surface finish and good dimensional stability between component lots with faster processing compared to traditional manufacturing methods. This experimental compression molding capability was developed for the ME composites lab using unidirectional carbon fiber prepreg composites. A direct comparison was drawn between autoclave and compression molding methods to validate compression molding as an alternative manufacturing method in that lab. A method of manufacturing chopped fiber from existing unidirectional prepreg materials was developed and evaluated using destructive testing methods. The results from …

Molecular Dynamics Simulation Of Force-Controlled Nanoindentation, Keaton Jaramillo

Mechanical Engineering Undergraduate Honors Theses

The aim of this honors research is to develop a force-controlled nanoindentation algorithm for molecular dynamics simulation. The algorithm was tested on Silicon using the Tersoff potential and Gold using the Embedded-Atom Method (EAM) potential. The effect of varying the damping parameters that adjust the system pressure and changing run length between force iterations is explored. The force-controlled algorithm was developed and shown to be working by correlating pop-in events shown in the force versus displacement (P-h) curves to visualization software showing phase transformation or dislocation events in the sample.

Polyacrylonitrile Copolymers: Effects Of Molecular Weight, Polydispersity, Composition, And Sequencing On Thermal Ring-Closing Stabilization, Jeremy D. Moskowitz

Dissertations

Controlled polyacrylonitrile (PAN)-based carbon fiber precursors with defined molecular weights, polydispersities, compositions, and architectures have been prepared for their study on thermal ring-closing stabilization behavior. PAN and its copolymers of number average molecular weights exceeding 170,000 g/mol were successfully synthesized via low temperature reversible addition-fragmentation chain transfer (RAFT) polymerization. RAFT polymerizations of PAN-based precursors were compared to conventional free radical solution polymerizations with a focus on the effects of molecular weight and polydispersity on structural evolution and cyclization efficiency. When RAFT polymerization was extended to copolymers, it was found that RAFT copolymers achieved greater cyclization intensities and improved thermal stability …

A Comparison Of The Bond Behavior Of Pbo-Frcm Composites Determined By Double-Lap And Single-Lap Shear Tests, Lesley Sneed, T. D'Antino, C. Carloni, C. Pellegrino

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This paper presents the results of an investigation on the bond behavior and stress-transfer mechanism of polyparaphenylene benzo isoxazole (PBO) fiber-reinforced cementitious matrix (FRCM) composites bonded to a concrete substrate using double-lap and single-lap shear tests. Results of double-lap shear tests with different composite bonded lengths and widths are presented and compared with those from single-lap shear tests previously reported by the authors. The idealized load response developed from single-lap shear tests is found to characterize the response of the composite in double-lap shear tests, although with a few key differences. With the double-lap shear test, load redistribution among the …

Ozone Reaction With Interior Building Materials: Influence Of Diurnal Ozone Variation, Temperature And Humidity, Donghyun Rim, Elliott T. Gall, Randy L. Maddalena, William W. Nazaroff

Mechanical and Materials Engineering Faculty Publications and Presentations

Elevated tropospheric ozone concentrations are associated with increased morbidity and mortality. Indoor ozone chemistry affects human exposure to ozone and reaction products that also may adversely affect health and comfort. Reactive uptake of ozone has been characterized for many building materials; however, scant information is available on how diurnal variation of ambient ozone influences ozone reaction with indoor surfaces. The primary objective of this study is to investigate ozone-surface reactions in response to a diurnally varying ozone exposure for three common building materials: ceiling tile, painted drywall, and carpet tile. A secondary objective is to examine the effects of air …

Characterizing Strain Accumulation, Residual Stress, And Microstructure Of Additive Manufactured Materials, Hannah K. Woods, Todd A. Book, Catalina Parada, Michael D. Sangid

The Summer Undergraduate Research Fellowship (SURF) Symposium

Additive Manufacturing (AM) is a rapidly evolving fabrication technology beneficial for its cost-saving potential to produce complex, low-volume shapes. However, AM materials are currently limited to nonstructural applications due to variability in their structural integrity, particularly their fatigue lives. IN718, Ti64, and Al10MgSi specimens manufactured by Direct Metal Laser Sintering (DMLS) were characterized based on variation of post-processing techniques and build direction. To understand the impact of each variable, surface roughness, hardness, residual stresses, microstructure, and strain accumulation in response to Low Cycle Fatigue (LCF) were studied. The use of Electron Backscatter Diffraction (EBSD) provided grain orientation and grain size …

Influence Of Warping On Stress For Restrained Concrete Slabs: For Application To Crcp, Corey M. Beck, W. Jason Weiss, Nathan T. Todd

The Summer Undergraduate Research Fellowship (SURF) Symposium

Continuously-reinforced concrete pavement (CRCP) is widely used in transportation system because of its low maintenance requirement. However, the need for large volumes of steel creates a high cost for new construction. The Illinois Tollway is preparing to substantially renovate highways in and around Chicago and this work seeks to understand how concretes of varying mixture designs can be made thinner by reducing the amount of built-in stress. The experiment examines warping in beams subjected to various degrees of restraint, in an effort to assess effectiveness at reducing warping in continuously reinforced concrete pavements. Value added methodologies such as internal curing …

Examining The Hydration And Mechanical Properties Of Cement Paste Containing Cellulose Nanocrystals, Yvette Valadez-Carranza, Charles Y. Chiu, W. Jason Weiss, Pablo Zavattieri, Jeffrey P. Youngblood

The Summer Undergraduate Research Fellowship (SURF) Symposium

Cellulose nanocrystals (CNCs) are a nano-scaled particulae material that has been shown to improve strength in cementitious pastes. One advantage of CNCs compared to other nano-materials is that CNCs are renewable and sustainable. The objective of this investigation is to investigate the influence of additional alkali content on the behavior of CNCs in cement paste. This work evaluates flexural and compressive strength as a function of heat of hydration—which measures the extent of reaction. Previous mechanical tests on cement paste containing cellulose nanocrystals (CNCs) have shown CNCs to improve the flexural strength of cement paste by approximately 30%. Isothermal calorimetry …

Temperature Dependent Surface Reconstruction Of Freely Suspended Films Of 4-N-Heptyloxybenzylidene-4-N-Heptylaniline, Daniel E. Martinez Zambrano

Lawrence University Honors Projects

Surfaces of freely suspended thick films of 4-n-heptyloxybenzylidene-4-n-heptylaniline (7O.7) in the crystalline-B phase have been imaged using non-contact mode atomic force microscopy. Steps are observed on the surface of the film with a height of 3.0 +/- 0.1 nm corresponding to the upright molecular length of 7O.7. In addition, we find that the step width varies with temperature between 56 and 59 degrees C. The steps are many times wider than the molecular length, suggesting that the steps are not on the surface but instead originate from edge dislocations in the interior. Using a strain model for liquid crystalline layers …

Investigating The Cause Of Unique Mechanical Behavior In Platinum Alloy Guidewire Tips, Evan Borgeson, Alfred Rosen

Materials Engineering

The platinum alloy used by Abbott Vascular in guidewire tips exhibits a yielding behavior characterized by an abrupt transition from elastic to plastic zones and high ductility. This yielding behavior was hypothesized to be a result of one of three structural phenomena: ordering, solute strain aging, or interstitial strain aging. To test for these strengthening mechanisms in the wire, X-ray diffraction analysis, heat treatments, and tensile testing were completed. The wire has a diameter of 0.0025 inches and was supplied in two forms, the final stress relieved state, and as-drawn from the production line. Heat treatments were performed at 130 …

Forest Sign Maker, Victor Espinosa Iii, Kevin Ly, Lisa Yip

Mechanical Engineering

Executive Summary:

The Inyo National Forest is arguably one of the most beautiful locations in California, containing natural masterpieces such as Mount Whitney and the Ancient Bristlecone Pine Forest. Despite its magnificence, the Inyo National Forest can be a treacherous region. The Friends of the Inyo take pride in being able to facilitate the viewing experience for all outdoorsmen by maintaining the mountain trails, which includes providing adequate trail signage.

Unfortunately, there is a fundamental issue with the recent state of trail signage in the Inyo National Forest: the rate at which signs are being vandalized or naturally destroyed is …

Analysis Of Compression Creep Deformation Of 7050 Aluminum Large Scale Open Die Forgings During The Solution Heat Treatment Process, Ashley Lopez, Elysha Cole

Materials Engineering

A stress, ranging from 104.17 to 166.67 psi, was applied to 0.5 in diameter cylindrical samples of 7050 aluminum using a manufactured fixture that applies stress using an indenter with a diameter of 0.127 in. The stress range used replicates the stresses produced on large scale forgings weighing up to 4000 lbs. We chose a maximum, medium and low stress as our stress parameters. The samples were placed into the fixture for stability then placed in a furnace heated to 890°F which is the solution heat treatment temperature for 7050 aluminum. The heat treatment times varied between 4 and 24 …

Improving Product Design By Predicting Flexural Strength Of A Honeycomb Core Sandwich Panel Composite Using Ply Tensile Strength, Justin Lui, Javal Patel

Materials Engineering

The use of composite sandwich panels has increased in the aerospace industry. Prediction of a theoretical composite construction's flexural properties is important for efficient composite product designs. Utilizing the four point flexure geometry defined by Zodiac Aerospace, Santa Maria, CA, a mechanical model was derived to predict the flexural behavior of a theoretical honeycomb core sandwich composite using laminate tensile properties. The most common failure mode of Zodiac Aerospace’s four point bend test is a failure in tension of the bottom laminate. Given this information, ASTM D3039 (Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials) was chosen …

Measuring Strain In Trusses, Spencer Metzsch

Senior Theses

Strain is an important quantity in engineering design and materials science that relates the deformation of a material to its original length, through a percentage. Different materials exhibit particular qualities under loading, for example the amount of strain due to a certain magnitude of force, or the amount of strain that can be borne before failure. This experiment aims to compare the relative strengths of three common truss configurations by measuring the strain in their members under loading. The Queen’s post truss was found to be the best at minimizing strain under similar loading conditions.

Enhancing Grain Refinement Of Austenitic Steel With Ti Additions By Melt Treatment Sequence Optimization, Gun Ge, Semen Naumovich Lekakh, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Characterizing Water As Gap Fill For Double Glazing Units, Bright Adu

Masters Theses & Specialist Projects

The use of sunlight has always been a major goal in the design and operation of commercial buildings to minimize electrical consumption of artificial lighting systems. Glazing systems designed to allow optimal visible light transmission also allow significant unwanted direct solar heat gain caused by infrared light. Conversely, glazing systems that are designed to reflect unwanted direct solar heat gain significantly reduce the transmittance of visible light through windows. The goal of this research was to characterize the performance of water as gap-fill for double-glazing units in eliminating the compromises that exist in current glazing systems with respect to light …

Characterization Of Silicon Phosphorus Alloy For Device Applications, Larry C. Cousar

Graduate Theses and Dissertations

A new material of highly-phosphorus doped silicon for device applications was characterized and analyzed for new material properties. Devices such as NMOS transistors and other CMOS compatible devices may benefit from new materials that reduce external resistances and increase drive currents.

Material characterization requires numerous techniques and technologies to determine electrical, optical, and physical characteristics. For this work, Hall measurement, X-ray Diffraction, Raman Spectroscopy, Photoluminescence Characterization, and Spectroscopic Ellipsometry were used to better understand this new material. The results may lead to new models for silicon phosphorus alloys.

Large-Scale Graphene Film Deposition For Monolithic Device Fabrication, Khaled Al-Shurman

Graduate Theses and Dissertations

Since 1958, the concept of integrated circuit (IC) has achieved great technological developments and helped in shrinking electronic devices. Nowadays, an IC consists of more than a million of compacted transistors.

The majority of current ICs use silicon as a semiconductor material. According to Moore's law, the number of transistors built-in on a microchip can be double every two years. However, silicon device manufacturing reaches its physical limits. To explain, there is a new trend to shrinking circuitry to seven nanometers where a lot of unknown quantum effects such as tunneling effect can not be controlled. Hence, there is an …

Prediction Of Shear Strength And Ductility Of Cyclically Loaded Reinforced Concrete Columns Using Artificial Intelligence, Nicholas Gordon

UNLV Theses, Dissertations, Professional Papers, and Capstones

The shear strength and deformation capacities of reinforced concrete (RC) columns are governed by a multitude of variables related to material properties of the steel and concrete used in the design and construction of the columns. Predicting performance of RC columns using design variables is a complex, non-linear problem. The prediction of shear strength and ductility for these types of structural members has historically been performed using empirically or semi-empirically derived formulae based on experimental results. The introduction of cyclical lateral loading, such as the forces imposed on a structure during an earthquake, can result in severe degradation of shear …

A Multi-Scale Based Model For Composite Materials With Embedded Pzt Filaments For Energy Harvesting, A.E. El-Etriby, M.E. Abdel-Meguid, K.M. Shalan, Tarek Hatem, Yehia Bahei-El-Din

Centre for Advanced Materials

Ambient vibrations are major source of wasted energy, exploiting properly such vibration can be converted to valuable energy and harvested to power up devices, i.e. electronic devices. Accordingly, energy harvesting using smart structures with active piezoelectric ceramics has gained wide interest over the past few years as a method for converting such wasted energy. This paper provides numerical and experimental analysis of piezoelectric fiber based composites for energy harvesting applications proposing a multi-scale modeling approach coupled with experimental verification. The multi-scale approach suggested predicting the behavior of piezoelectric fiber-based composites use micromechanical model based on Transformation Field Analysis (TFA) to …