Structural Materials Commons^™

Micro-Mechanical Characterization Of Uhpc Stiffness Mechanisms: Towards A Better Understanding Of Concrete Elastic Modulus, Charissa N. Puttbach

Graduate Theses and Dissertations

Current design code equations for estimating the elastic modulus of specialty concretes like ultra-high performance concrete are not all suitable. Developing empirical curves from exhaustive experimental testing is challenging for concretes that may have high levels of cement replacement with mineral admixtures and fibers at varying volume contents. As such, an alternative approach is taken that seeks to understand the constituent microscale stiffness mechanisms and relate the results to the macroscale. Micropillars are fabricated on several cement paste phases using a focused ion beam. A modified pico-indenter is used to determine the linear and non-linear behavior under micro-compression loading. Micropillar …

Initial Exploration Of Reduced Gyrations For Arkansas Asphalt Mix Designs, Jocie L. Baker

Graduate Theses and Dissertations

The most common distresses in asphalt pavement are cracking and rutting. These distresses plague almost every asphalt roadway in the world. Finding ways to mitigate these distresses will improve the performance of asphalt pavements. One way to combat the premature cracking of asphalt in the field is to ensure there is enough asphalt binder within the mix. This will help the flexibility of the asphalt undergoing large loads and deformation. However, it is widely accepted that mix designs across the country lack the appropriate amount of asphalt binder in their mixes, causing dry mix designs that are subject to cracking …

Xps And Ipe Determination Of Band Offsets Of Germanium Based Materials, Justin Michael Rudie

Graduate Theses and Dissertations

Germanium tin and silicon germanium tin are group IV semiconductor alloys that have gained significant interest in recent years for their potential use in optoelectrical devices. While silicon and germanium are indirect bandgap materials on their own, alloying them with tin in sufficient quantities leads to a transition to direct bandgap alloys. Direct gap performance opens the door for efficient light emitting and detecting devices fabricated entirely on group IV materials that are compatible with the industry standard CMOS manufacturing techniques. Germanium tin and silicon germanium tin have bandgaps that respond to light in the mid to near infrared spectrum …

Shear Strength Of Concrete Beams Made With Belitic Calcium Sulfoaluminate Cement, Caleb W. Chesnut

Graduate Theses and Dissertations

The need for a cleaner alternative to portland cement (PC) concrete has led to increasing interest in alternatives to PC. Structural properties of most of these alternative cements are still an open research topic. One promising alternative cement is belitic calcium sulfoaluminate (BCSA) cement. The study presented in this paper investigated the shear strength, long term compressive strength, and carbonation in BCSA cement and PC concrete beams. A total of twelve eight-foot long beams were made; eight BCSA cement concrete beams and four PC concrete beams to be tested at various ages depending on cement type. Two beams of each …

Frequency Effect On Peak Pressure Coefficients Using The Narrowband Synthesis Random Flow Generator (Nsrfg) Method, Zayuris Del Carmen Atencio Mojica

Graduate Theses and Dissertations

The collapse of the Tacoma Narrows Bridge in Washington state in 1940 due to high wind forces gave structural engineers notice of the importance of understanding the behavior of wind forces on infrastructure. Wind forces play an important role in the design of buildings and other structures. ASCE 7-16 is the manual used for the design of these buildings and other structures throughout the country. These design criteria have been approved based on research projects involving experimental procedures. For the design of wind loads, ASCE 7-16 uses criteria based on wind tunnel (WT) tests. However, since the development of computing …

Phase-Field Modeling Of The Polymer Membrane Formation Process For Micro- And Ultra-Filtration, Michael Rosario Cervellere

Graduate Theses and Dissertations

Porous polymer membrane filters are widely used in separation and filtration process. Micro- and ultra-filtration membranes are commonly used in biopharmaceutical applications such as filtering viruses and separating proteins from a carrier solution. The formation of these membrane filters via phase inversion is a complex and interconnected process where varying casting conditions can have a wide variety of effects on the final membrane morphol- ogy. Tailoring membrane filters for specific performance characteristics is a tedious and time consuming process. The time and length scales of membrane formation make it extremely difficult to experimentally observe membrane formation. Modeling the membrane formation …

Investigation Of Membrane Based Processes For Biomedical Applications, Efecan Pakkaner

Graduate Theses and Dissertations

As substantial developments were achieved in nanotechnology and polymer engineering, especially in the last few decades, the use of membranes and membrane-based procedures was found to be expanding into more and more research and development areas; including biological engineering, life sciences and biomedical engineering. Not only have they been the main focus of meaningful research, but they have also been the main pieces of the solutions to very thorny problems encountered within a wide range of applications from microfluidics to water treatment, thanks to their versatility, cost-effectiveness and biocompatibility, when compared to conventional separation techniques. To celebrate and embrace these …

An Investigation Of Testing Parameters On The Frictional Properties Of Patterned Core-Shell Nanostructures, Colin Phelan

Graduate Theses and Dissertations

Friction tests are a beneficial means to analyze the tribological characteristics and advantages of materials and textured surfaces. However, the selected test parameters can significantly influence the results. This work explores the significance of the friction testing parameters on the frictional performances of core-shell nanostructure-textured surfaces (CSNTSs). Several applied normal loads (10 μN, 100 μN, and 500 μN) and diamond counterface indenter tip radii (1 μm, 5 μm, and 20 μm) were selected for the testing of Al/diamond-like-carbon (DLC) and Al/amorphous silicon (a-Si) CSNTSs. The measured friction values of the CSNTSs were then compared to a matching Al/DLC film and …

An Investigation Into The Effects Of Fly Ash On Freeze-Thaw Durability Prediction, Yancy Schrader

Graduate Theses and Dissertations

Air is purposefully entrained into concrete primarily to improve resistance to freeze-thaw deterioration while saturated with water. Air entraining admixtures (AEAs) are chemical admixtures designed to entrain air into the concrete to provide adequate resistance to the effects of freezing and thawing. One of the challenges associated with air entrainment in concrete is the interaction of an AEA with supplementary cementitious materials present in the concrete, particularly fly ash. Fly ash is a by-product of the coal fired electrical generation industry, and often contains residual unburned carbon and other components that can increase the AEA demand of a particular concrete …

Effect Of Citric Acid On Slump, Compressive Strength, And Setting Time Of Belitic Calcium Sulfoaluminate Concrete, Israel Aguilar Rosero

Graduate Theses and Dissertations

Belitic calcium sulfoaluminate (BCSA) cement has well established advantages related to fast setting time, fast strength gain, long-term strengths, shrinkage, and sustainability. Due to its fast setting and hardening, this type of cement has historically been used to repair concrete structures, highways, and runways. This work provides much needed guidance on establishing mix design criteria for BCSA cement. Guidance is also given on the effects of set retarders on strength, slump, and setting times. Citric acid and a phosphonic acid-based admixture were tested as retarders for different concrete mixtures. Three studies were performed. In the slump study five different water …

Leveraging Biomimicry And Additive Manufacturing To Improve Load Transfer In Brittle Materials, Ana Paula Bernardo

Graduate Theses and Dissertations

With the emergence of Additive Manufacturing (i.e., 3D printing) in construction, new strategically designed shapes can be created to improve load transfer through structural members and foundations. Cross-sections can be optimized to carry load using less material, or even using weaker constituent materials, like soils, which are cheap and abundant. The goal of this research is to investigate the benefits of using cellular patterns which leverage biomimicry in civil engineering applications, since nature has perfectly engineered materials and patterns which carry loads with the least amount of material possible. Most of the periodic cellular work to date has focused on …

Application Of Percentage Within Limits Concepts On A Balanced Mix Design Of Asphalt Mixtures, Elvis Alexander Castillo Camarena

Graduate Theses and Dissertations

Many agencies have incorporated rutting, and more recently cracking, laboratory test requirements in the design process of asphalt mixtures. The objective of each additional specification is to produce a balance between the stability and durability of the final product. Although a performance-engineered mixture design (PEMD), denoted here as a balanced mix design (BMD), offers compelling benefits, there is concern regarding the compatibility of the BMD with current construction practices. The objective of this work is to correlate a BMD method with realistic binder content construction tolerances by applying the concepts of a percent-within-limits (PWL) approach to field QC/QA. First, Chapter …

Development Of Multi-Axial Fatigue Retrofits For Lock Gate Components, Logan Verkamp

Graduate Theses and Dissertations

Lock gates are essential infrastructure components to the United State (US) supply chain. They create large cost savings and environmental benefits when compared with traditional methods of transport (freight and rail). Because of the large quantity of goods and dependence on these shipping chains, the US economy can be drastically affected by an unexpected gate closure. Unfortunately, many lock gates within the US have reached or exceeded their designed life. Due to the intensity of cyclic loads and the environment, fatigue cracks have become a prominent issue. Developed cracks near the pintle region (a joint which the gate rotates and …

Investigation Of Nanomaterial Based Photovoltaic Panel Packaging Materials, Xingeng Yang

Graduate Theses and Dissertations

In this research, nanomaterial-based packaging materials for photovoltaic (PV) panels are investigated. A hydrophobic/anti-reflective surface coating which not only repels water from the top glass of a PV panel but at the same time reduces its light reflectance is investigated. COMSOL simulation results indicate that taller ellipsoid rod (aspect ratio = 5) reflects less light than shorter rod (aspect ratio = 0.5) in the desired spectrum for solar energy harvest from 400nm-700nm. The addition of a polymer layer on these ellipsoid rods broadens the light incident angle from 23° to 34°, from which light can be efficiently absorbed. Based on …

Understanding The Evolution Of Surface Texture Under Boundary Lubrication, Salil T. Bapat

Graduate Theses and Dissertations

The objective of this research was to understand the evolution of surface texture under boundary/mixed lubrication (BL). Significant material/energy losses occur during BL because of direct contact between the two surfaces. Traditionally, tribofilms have been studied extensively for BL while textures have been used as a static engineering design parameter to enhance lubricant film properties. However, texture is dynamic at the tribological mating interface, where both physical and chemical interactions are continuously modulated. The evolution and the interplay between the tribofilm and texture is least studied in the literature, which is the focus of this research.

MoS2-based lubricants, known for …

Deformation Behavior Of Al/A-Si Core-Shell Nanostructures, Robert Andrew Fleming

Graduate Theses and Dissertations

Al/a-Si core-shell nanostructures (CSNs), consisting of a hemispherical Al core surrounded by a hard shell of a-Si, have been shown to display unusual mechanical behavior in response to compression loading. Most notably, these nanostructures exhibit substantial deformation recovery, even when loaded much beyond the elastic limit. Nanoindentation measurements revealed a unique mechanical response characterized by discontinuous signatures in the load-displacement data. In conjunction with the indentation signatures, nearly complete deformation recovery is observed. This behavior is attributed to dislocation nucleation and annihilation events enabled by the 3-dimensional confinement of the Al core. As the core confinement is reduced, either through …

Mitigation And Evaluation Of Alkali-Silica Reaction (Asr) And Freezing And Thawing In Concrete Transportation Structures, Richard Albert Deschenes Jr.

Graduate Theses and Dissertations

An evaluation of alkali-silica reaction (ASR) and freezing and thawing (F/T) in concrete transportation structures is presented along with mitigation methods for slowing the rate of deterioration in concrete. A combination of field and laboratory testing confirms ASR deterioration is exacerbated by exposure to F/T. Laboratory testing indicates an aggregate previously deemed inert to ASR, caused ASR deterioration in several concrete pavement and transportation structures. Existing standard test methods deem this aggregate safe for use in concrete. A modified test method shows the concrete can deteriorate rapidly when subjected to cycles of conditions promoting ASR and F/T. Several structures containing …

Optimization Of Concrete Mixtures For Use In Structural Elements, Waleed Almutairi

Graduate Theses and Dissertations

Portland cement is an essential ingredient in concrete. The use of cement is to enhance the strength as well as other hardened properties of concrete mixtures. Determining the accurate amount of cement is important because the required strength may not be achieved if not enough cement is used. By contrast, when using too much cement, concrete cracking may occur that leads to reducing durability. Researchers at the University of Arkansas (UA) have shown that many bridge decks achieve their 28 day design strength of 4000 psi by 7 days of age. Bridge decks having high strength may experience cracking, which …

Influence Of Concrete Compressive Strength On Transfer And Development Lengths Of Prestressed Concrete, Alberto Teodoro Ramirez-Garcia

Graduate Theses and Dissertations

This research examines the relationship between concrete compressive strength and strand bond. The goal of this research was to develop an equation that relates strand bond to concrete compressive strength at strand release (approximately 1 day of age) and at 28 days of age, and those equations are presented in this investigation. Strand bond is assessed by measuring the transfer length and development length for prestressed beams cast in the laboratory. In the U.S., strand bond is predicted using transfer length and development length equations provided by the American Concrete Institute (ACI-318) Building Code and American Association of State and …

Phase-Field Models For Simulating Physical Vapor Deposition And Microstructure Evolution Of Thin Films, James Stewart Jr.

Graduate Theses and Dissertations

The focus of this research is to develop, implement, and utilize phase-field models to study microstructure evolution in thin films during physical vapor deposition (PVD). There are four main goals to this dissertation. First, a phase-field model is developed to simulate PVD of a single-phase polycrystalline material by coupling previous modeling efforts on deposition of single-phase materials and grain evolution in polycrystalline materials. Second, a phase-field model is developed to simulate PVD of a polymorphic material by coupling previous modeling efforts on PVD of a single-phase material, evolution in multiphase materials, and phase nucleation. Third, a novel free energy functional …

Characterization Of Silicon Phosphorus Alloy For Device Applications, Larry C. Cousar

Graduate Theses and Dissertations

A new material of highly-phosphorus doped silicon for device applications was characterized and analyzed for new material properties. Devices such as NMOS transistors and other CMOS compatible devices may benefit from new materials that reduce external resistances and increase drive currents.

Material characterization requires numerous techniques and technologies to determine electrical, optical, and physical characteristics. For this work, Hall measurement, X-ray Diffraction, Raman Spectroscopy, Photoluminescence Characterization, and Spectroscopic Ellipsometry were used to better understand this new material. The results may lead to new models for silicon phosphorus alloys.

Large-Scale Graphene Film Deposition For Monolithic Device Fabrication, Khaled Al-Shurman

Graduate Theses and Dissertations

Since 1958, the concept of integrated circuit (IC) has achieved great technological developments and helped in shrinking electronic devices. Nowadays, an IC consists of more than a million of compacted transistors.

The majority of current ICs use silicon as a semiconductor material. According to Moore's law, the number of transistors built-in on a microchip can be double every two years. However, silicon device manufacturing reaches its physical limits. To explain, there is a new trend to shrinking circuitry to seven nanometers where a lot of unknown quantum effects such as tunneling effect can not be controlled. Hence, there is an …

Development Of Micro-Hall Devices For Current Sensing, Thomas White

Graduate Theses and Dissertations

In this work, micro-Hall devices were developed for the purpose of sensing current within a high temperature and high power environment. GaAs HEMT, InGaAs pHEMT, and GaN HEMT structures were studied. These structures were grown by molecular beam epitaxy. Processing techniques including photolithography, metallization, Si deposition, wet etching, and dry etching were studied. Electrical characterization measurements including low frequency noise, Hall effect, sensitivity, capacitance-voltage, and current-voltage were performed.

Electron mobility and sheet carrier density studies were performed for both the InGaAs pHEMT and GaAs HEMT structures. Results indicated the InGaAs pHEMT was superior and thus fabricated as the micro-Hall device. …

Atom-Based Geometrical Fingerprinting Of Conformal Two-Dimensional Materials, Mehrshad Mehboudi

Graduate Theses and Dissertations

The shape of two-dimensional materials plays a significant role on their chemical and physical properties. Two-dimensional materials are basic meshes that are formed by mesh points (vertices) given by atomic positions, and connecting lines (edges) between points given by chemical bonds. Therefore the study of local shape and geometry of two-dimensional materials is a fundamental prerequisite to investigate physical and chemical properties. Hereby the use of discrete geometry to discuss the shape of two-dimensional materials is initiated.

The local geometry of a surface embodied in 3D space is determined using four invariant numbers from the metric and curvature tensors which …

Durability Of Silane Sealer In A Highly Alkaline Environment, Cameron David Murray

Graduate Theses and Dissertations

Alkali-silica reaction (ASR) is a chemical reaction between siliceous minerals present in certain aggregates and alkalis in the concrete pore solution. The reaction can lead to expansion and severe damage in concrete members. One method to mitigate ASR expansion is to use a penetrating sealer such as silane. A set of columns located in a food preparation facility was treated with silane and a complimentary laboratory study was performed. A cleaning regimen involving application of an alkaline cleaner is employed at the facility, followed by rinsing with hot, pressurized water. The purpose of this research is to evaluate the effectiveness …

Creep, Fatigue And Creep-Fatigue Interactions In Modified 9% Cr - 1% Mo (P91) Steels, Valliappa Kalyanasundaram

Graduate Theses and Dissertations

Grade P91 steel, from the class of advanced high-chrome ferritic steels, is one of the preferred materials for many elevated temperature structural components. Creep-fatigue (C-F) interactions, along with oxidation, can accelerate the kinetics of damage accumulation and consequently reduce such components' life. Hence, reliable C-F test data is required for meticulous consideration of C-F interactions and oxidation, which in turn is vital for sound design practices. It is also imperative to develop analytical constitutive models that can simulate and predict material response under various long-term in-service conditions using experimental data from short-term laboratory experiments. Consequently, the major objectives of the …

Investigation Of Negative Differential Resistance Phenomena In Quantum Well Heterostructures, Nazariy Andrushchak

Graduate Theses and Dissertations

Increasing interest in entirely new possibilities for quantum mechanical description of carriers transport is becoming more evident with the developing advancements in epitaxial growth technique. Consequently, molecular beam epitaxy (MBE) technique is considered to be the most precise technique that allows the growth of ultra-thin layers of different compositions.

Those structures can be designed to investigate the wave-nature of carriers, which broadens the possibilities in device design and fabrication for a specific area. In this thesis the fundamental study of the real space charge transfer (RST) mechanism that took place in quantum well heterostructures and led to the negative differential …

Surface Wetting And Friction Studies Of Nano-Engineered Surfaces On Copper Substrate, Julius Sheldon Morehead

Graduate Theses and Dissertations

Nano-engineered-textures on a material surface can dramatically improve the wetting and non-wetting properties of a surface, and they also show promise to address friction issues that affect surfaces in contact. In this work, aluminum-induced crystallization (AIC) of amorphous silicon (a-Si) was used to produce nano-textures on copper (Cu) substrates. A study was performed to examine the effects of changing the annealing conditions and a-Si thickness on nano-texture formation. The creation of various nano-topographies and chemically modifying them using octafluorocyclobutane (C4F8) was performed to control hydrophilicity, hydrophobicity, and oil affinity of nano-textured surfaces. A video-based contact angle measurement system was used …

Degradation Of Polystyrene Foam Under Radiant Heat Flux, James Butler

Graduate Theses and Dissertations

As the demand for liquefied natural gas has increased, safety concerns about the performance of transport vessels under fire conditions have been raised. Current codes for the sizing of the pressure relief systems require that the vessels are able to withstand an emmissive heat flux of 108kW/m2 and do not take into account the effects of insulation loss due to thermal decomposition of the insulation materials. To address this possible oversight in the current code models were presented to a working group organized by the Society of International Gas Tanker and Terminal Operators Ltd. focusing on the decomposition rate of …