Open Access. Powered by Scholars. Published by Universities.®
- Discipline
- Institution
- Keyword
- Publication
- Publication Type
Articles 1 - 6 of 6
Full-Text Articles in Structural Materials
Detection Of Voids In Prestressed Concrete Bridges Using Thermal Imaging And Ground-Penetrating Radar, David G. Pollock, Kenneth J. Dupuis, Benjamin Lacour, Karl R. Olsen
Detection Of Voids In Prestressed Concrete Bridges Using Thermal Imaging And Ground-Penetrating Radar, David G. Pollock, Kenneth J. Dupuis, Benjamin Lacour, Karl R. Olsen
Faculty Publications - Biomedical, Mechanical, and Civil Engineering
Thermal imaging and ground-penetrating radar was conducted on concrete specimens with simulated air voids. For the thermal imaging inspections, six concrete specimens were constructed during the month of June 2007 to simulate the walls of post-tensioned box girder bridges. The objective was to detect simulated air voids within grouted post-tensioning ducts, thus locating areas where the post-tensioning steel strands are vulnerable to corrosion. The most important deduction taken from these inspections was that PT-ducts and simulated voids were more detectable in the 20 cm (8 in.) thick specimens than in the 30 cm (12 in.) thick specimens. While inspections of …
Development Of Low Temperature Alpha Alumina Coatings By Ac Magnetron Sputtering, Andrew Cloud
Development Of Low Temperature Alpha Alumina Coatings By Ac Magnetron Sputtering, Andrew Cloud
Mechanical Engineering Undergraduate Honors Theses
Alpha-phase aluminum oxide thin films were created using an Isoflux ICM-10 dual target inverted cylindrical magnetron sputtering system using mid-frequency AC power supplies. Alpha alumina films were deposited at a magnetron power of 6 kW, 50% oxygen partial pressure by volume, and -35 V DC bias. Film thickness, substrate material, and position and orientation within the deposition chamber were varied. To ensure the deposition conditions are suitable for alloys, the substrate temperature was measured using temperature indicating liquids. The experimental results, supported by Explicit Euler numerical analysis, revealed a steady state temperature of ~480°C at 6kW. Transmission electron microscopy (TEM) …
Thermal Damage Approach Of Concrete: Application To Specimens Subjected To Combined Compressive And High Temperature Loads, Abdellah Menou, Ghassan Mounajed, Hocine Boussa, Christian La Borderie, Khalid Lafdi
Thermal Damage Approach Of Concrete: Application To Specimens Subjected To Combined Compressive And High Temperature Loads, Abdellah Menou, Ghassan Mounajed, Hocine Boussa, Christian La Borderie, Khalid Lafdi
Chemical and Materials Engineering Faculty Publications
Within the framework of study of concrete structures subjected to fire, .a theoretical and experimental work was conducted. The aim of this study was to investigate and to model the damage mechanisms of concrete after their exposure to high temperatures. The multiphase Digital Concrete Model as well as the damage model, MOD EV, which were both implemented on the finiteelem~ rit software package, SYMPHONIE, were used simμltaneously to assess the thermal damage of the concrete. In order to validate the thermal damage model, an experimental investigation was performed. The mechanical characteristics of 5 cementitious materials, which included cement paste, mortar, …
Abrasion Resistance Of Concrete Made With Various Types Of Aggregates, Mohamed Hamada Rashwan
Abrasion Resistance Of Concrete Made With Various Types Of Aggregates, Mohamed Hamada Rashwan
Archived Theses and Dissertations
No abstract provided.
Sub-Surface Corrosion Research On Rock Bolt System, Perforated Ss Sheets And Steel Sets For The Yucca Mountain Repository — Quarterly Technical Report No. 14, Dhanesh Chandra, Jaak J.K. Daemen
Sub-Surface Corrosion Research On Rock Bolt System, Perforated Ss Sheets And Steel Sets For The Yucca Mountain Repository — Quarterly Technical Report No. 14, Dhanesh Chandra, Jaak J.K. Daemen
Publications (YM)
This report shows the work done for this period in accordance to cooperative agreement of University of Nevada system for the Task 019 “Subsurface Corrosion Research on Rock Bolt System, Perforated SS Sheets and Steel Sets for the Yucca Mountain Repository”, the overall objective of which is to conduct corrosion research and predict the durability of rock-bolts and other underground metallic roof supports. We are performing oxidation tests using Thermogravimetric Analyzer (TGA), and Potentiodynamic and immersion tests to determine the corrosion rates of rock bolts. In this quarter specifically we have accomplished the following: Potentiodynamic tests were performed to determine …
Damping Of Magnetorheological Elastomers, Lin Chen
Damping Of Magnetorheological Elastomers, Lin Chen
Articles
The damping property of magnetorheological (MR) elastomers is characterized by a modified dynamic mechanical-magnetic coupled analyzer. The influences of the external magnetic flux density, damping of the matrix, content of iron particles, dynamic strain and driving frequency on the damping properties of MR elastomers were investigated experimentally. The experimental results indicate that the damping properties of MR elastomers greatly depend on the interfacial slipping between the inner particles and the matrix. Different from general composite materials, the interfacial slipping in MR elastomers is affected by the external applied magnetic field.