Ceramic Materials Commons^™

Processing And Characterization Of Ceramic Fiber Reinforced Porous Matrix Composites, Wen-Chiang Tu

Masters Theses

"The development of ceramic fiber reinforced ceramic matrix composites has been shown to be a promising approach for high toughness ceramic materials. The purpose of this work was to develop a new ceramic matrix composite(CMC) system based on a porous mullitic matrix reinforced with ceramic fibers. Unidirectional alligned fiber reinforced mullitic matrix composites were fabricated by a filament winding process. Prepregs were laminated and thermal processed in air. SEM fractographs of the composites were characterized and related to the observed load-deflection behaviors under 3-point flexure. The fracture surface expositions changed from extensive fiber tear-out to limited fiber pull-out as the …

Fabrication And Mechanical Property Analysis Of A Transparent, Glass Fiber Reinforced Polymer Matrix Composite, James R. Olson

Masters Theses

"A "transparent” composite was produced by reinforcing poly(methyl methacrylate) (PMMA) with unidirectional borosilicate glass fibers. Composites with 40 volume percent fiber had a modulus of rupture of 600 MPa which is six times greater than that of pure PMMA. Young's modulus for the same composite was 18 MPA which is nine times greater than the 2 MPa measured for pure PMMA. Work of fracture was 110 kJ/m² or more than double the 45 kJ/m² required to fracture pure PMMA. The optical transmission of the composite with 30 volume percent fiber was approximately 40 percent through a 10 mm …

The Effect Of Additives On Properties Of Pfn-Pfw Dielectric Materials, Weih-Min Liao

Masters Theses

"The purpose of this study was to investigate the effect of processing and additives on the properties of the Pb(Fe_1/2Nb_1/2)O₃-PB(Fe_2/3W_1/3)O₃ solid solutions. The basic composition was 70 m% Pb(Fe_1/2Nb_1/2)O₃ and 30 m% Pb(Fe_2/3W_1/3)O₃. The additives used were MnO, PbO and ZnNbO₆. Pressed compacts were sintered over the temperature range 900'C to 1050°C for 1 to 5 hours.

The influence of processing and composition on the properties was determined by measurement of density, shrinkage, dielectric constant, dissipation factor and …

Bubble Formation, Movement And Distortion In Viscous Glass, Simon Cheng-Ping Wang

Doctoral Dissertations

"A study of bubble formation, movement and distortion in viscous glass is described. A glass rod containing an irregularly shaped hole is heated to a temperature at where the glass viscosity is low enough to let the hole form a spherical bubble. Spheration occurs as the bubble moves upward in the glass rod. At the proper time, the rising bubble is decelerated and brought to a stop by increasing the glass viscosity by slowly reducing the temperature. The entrapped bubble is then cut from the glass rod and heated again, if necessary, to a lower temperature, to reduce distortion of …

The Effect Of Excess Lead Oxide On The Sintering Characteristics And Dielectric Properties Of Lead Magnesium Niobate Ceramics, Dyllan Jye-Lun Hong

Masters Theses

"The effect of lead oxide additions on sintering characteristics and dielectric properties of ferroelectric Pb₃MgNb₂O₉ based capacitors was studied. The basic dielectric compositions were formed by solid state reaction. Densification was studied as a function of PbO content over the temperature range 900 °C to 1000 °C for sintering times one to six hours depending on the amount of additive, and the sintering temperature.

Weight loss, density and shrinkage measurements of each composition were made in order to relate the effects of the excess PbO additions on the densification. The dielectric and electrical properties were …

An Apparatus For The Measurement Of Dc Electrical Conductivity And Seebeck Coefficient Of Semiconductors As A Function Of High Temperature And Oxygen Partial Pressure, George Francis Carini Ii

Masters Theses

"A computer controlled apparatus for the measurement of dc electrical conductivity and Seebeck coefficient as a function of temperature and oxygen partial pressure has been developed. Thermocouples are in electrical and thermal contact with the ends of the specimen bar. This allows both Seebeck and four-wire electrical conductivity measurements to be made in situ. Environmental enclosure of the specimen allows measurements over a range of oxygen activities from 1 to 10^-18 atm. A discussion of the measuring technique with schematics of the apparatus and data retrieval system is made. Results for measurements in selected oxide ceramics are compared to …

The Development Of Glass-Ceramic Matrix Composites And The Crystallization Of Two Glass-Ceramic Matrices, William M. Carty

Masters Theses

"In order to develop ceramic matrix composites for high temperature applications, two glass-ceramic matrices, one an yttrium aluminosilicate (YAS), the other a magnesium aluminosilicate (cordierite), were chosen as possible matrix compositions. Two separate sets of experiments were performed. Specimens were hot pressed and heat treated then analyzed for the crystallization products and C.T.E. Specimens were also prepared containing commercially available ceramic fibers and coated ceramic fibers to investigate fiber/matrix interactions and the effect of fiber additions on the crystallization of the glass matrices. DTA was employed to approximate the crystallization temperature of the glasses and to determine the effect of …

Glass Fiber Reinforced Polycarbonate Composites, Wen Ching Hu

Masters Theses

"The purpose of this work was to develop a transparent glass fiber reinforced polymer composite material which is superior to the transparent unreinforced thermoplastic in mechanical properties but similar in optical clarity. Polycarbonate matrix composite specimens containing 0 to 40 wt% SK-12 glass fiber were studied, with mechanical and optical properties determined as a function of glass fiber content. The mechanical properties -- flexural strength and elastic modulus increased with increasing glass fiber content. The optical properties -- transmission and transparency decreased with increasing glass fiber content. The factors which influence the mechanical and optical properties were investigated"--Abstract, page ii.

Causal Factors In The Hydration Susceptibility Of Periclase Aggregates, Chao-Min Cheng

Masters Theses

"The findings presented in this thesis are the result of a study of the hydration mechanism of pre-calcined periclase aggregates. It is hoped that these findings will provide the means to develop an economical, stable and hydration resistant layer on the surface of periclase aggregates by coating with appropriate chemical systems.

In the conduct of this study two sources of commercially obtained materials, Steetley 323, and China metal 90-10, supplied by the Quigley company, were characterized and treated with different concentrations of boron-containing water suspensions in order to impose an altered layer which would resist hydration.

Variables affecting hydration investigated …

Property Survey Of Y₂O₃-Al₂O₃-Sio₂-MₓoY Glasses, Amy Lee Applewhite

Masters Theses

"The purpose of this work was to investigate the properties of Y₂O₃-Al₂O₃-SiO₂-M_xO_y glasses. Many M_xO_y components were tested, but TiO₂ and B₂O₃ proved the most interesting. Glasses containing 5 to 25 wt % TiO₂ were melted and found to have improved chemical durability and a higher refractive index and density than the eutectic Y₂O₃-Al₂O₃-SiO₂ starting glass. These glasses could be crystallized to form an opaque glass ceramic. Glasses containing B₂O₃ were formed by exchanging SiO₂ with B₂O₃ while holding the Y₂O₃ and Al₂O₃ content constant. The density, hardness, refractive index, transformation temperature, softening temperature …

The Interfacial Phenomena Of Liquid Copper Of Sapphire Substrates, Jenq Liu

Masters Theses

"The wetting behavior of liquid copper on the sapphire is effected by the crystallographic orientation of the solid surface, the oxygen partial pressure, and the temperature. Each of these influences has been studied by the sessile drop technique, over the oxygen partial pressure range from 10^-2 to 10^-20 atm at temperatures of 1373°K, and 1523°K. The effect of oxygen partial pressure on the liquid copper surface energy follows the Gibbs Langmuir Law.

The crystallographic orientation of the sapphire surface causes variations in the contact angle. This is more significant for higher oxygen partial pressure, but is eliminated at …

Studies Of Defect Structure And Oxidation-Reduction Behavior Of Undoped Lamno₃, Sr-Doped Lamno₃ And Mg-Doped Lamno₃, Jen-Ho Kuo

Doctoral Dissertations

"Undoped LaMnO₃, Sr-doped LaMnO₃ and Mg-doped LaMnO₃ showed reversible oxidation-reduction behavior. These perovskites can be excess, stoichiometric or deficient in oxygen content depending on the specific conditions. Under very reducing conditions these oxides will decompose into new phases. Phase stabilities for these oxides were determined. The results showed that both Sr and Mg doping caused the LaMnO₃ to dissociate at higher oxygen activities than for undoped LaMnO₃.

Defect models were proposed to interpret the TG results, in which metal vacancies are assumed for the oxygen excess condition and oxygen vacancies are assumed for the oxygen deficient condition. Thermodynamic properties were …

Discussion Of "Lime-Enhanced Reduction Of Sulfide Concentrates: A Thermodynamic Discussion", Arthur E. Morris, Harry Flynn

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Influence Of Oxygen Activity On The Lattice Parameters And Thermal Expansion Of Mg And Sr-Doped Lacro₃, Sutham Srilomsak

Masters Theses

"Lanthanum Chromite, when used as the fuel cell interconnector material is exposed to extremely different oxygen activities on its two surfaces. In addition, it must also form coherent boundaries with the fuel electrode (anode) and air electrode (cathode) layers. In order to accomplish these functions the acceptor doped LaCrO₃ must not only be chemically stable over large oxygen activity ranges, but also have good thermal expansion coefficient of match with both the anode and cathode. Therefore, the objective of this study is to investigate these requirements for Mg and Sr doped LaCrO₃. The study was divided into …

The Effect Of Oxygen Partial Pressure On Oxygen And Carbon Incorporation In Czochralski Grown Single Crystal Silicon, Paul Shane Carter

Masters Theses

"The study herein detailed was made to determine the effect of varying the oxygen partial pressure of a Czochralski type crystal pulling furnace using conventional hardware and remelt silicon on the level of incorporated oxygen and carbon in the single crystal. The oxygen partial pressure was measured by a zirconia type oxygen sensor and controlled by additions of hydrogen or carbon dioxide to the argon purge gas. The oxygen and carbon incorporation measurements were made by the Fourier Transform Infrared (FTIR) method, using the American Standard for Testing Materials (ASTM) standard calibration.

During the study boules which were zero dislocation …

An Investigation Of The Low Voltage Failure Mechanism In Multilayer Ceramic Capacitors, Christopher John Brannon

Masters Theses

"Enhanced leakage current was induced into multilayer ceramic capacitors by the introduction of micro-cracks. These cracks extended from the surface through the electrode layers and were formed by means of thermal shock. The capacitors were then exposed to a low voltage bias and a humid atmosphere. Results indicated that a simple electrolytic solution mechanism may be responsible for the increased conduction, and that the proposed dendritic growth mechanisms may be more complex than necessary"--Abstract, p. ii

Glass Experiments In Space, Norbert J. Kreidl

Materials Science and Engineering Faculty Research & Creative Works

Current and potential glass research under microgravity includes studies of minimum cooling rate, homogeneous nucleation, diffusion, surface tension and enrichment, fining without buoyancy, avoidance of liquid phase separation, gel synthesis, composites and uniform micro balloons. The experiments do not just anticipate space fabrication but will also provide information and innovation encouraging advanced processing on earth. © 1986.

Reply, Paul W. Angel, Chandra S. Ray, Delbert E. Day

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.

Oxidation Kinetics Of Polycrystalline Srtio₃ And Lacro₃, Chi-Kung Jerry Yu

Doctoral Dissertations

"The oxidation kinetics of polycrystalline SrTiO₃ and LaCrO₃ were determined by measuring the time and temperature dependence of the weight and conductivity change of reduced samples. A region of fast diffusion followed by a reduced diffusion tail was observed in the TGA measurements. This observation can be interpreted as the initial diffusion along the boundaries and then spreading out into the lattice. The absence of the tail in the conductivity measurements is due to the high electron and hole mobility at the boundaries. The electrical conductivity and TGA results on Nb-doped LaCrO₃ show that at low oxygen …

The Effect Of Electrodes On The Thermally Stimulated Currents In Sodium Silicate Glass, Ruth Mogrovejo Cuzmar

Masters Theses

“Electrodes play an important role in the study of alkali ion motion in glasses when TSPC/TSDC techniques are used. Silver, gold and combinations of them were used in the study of Na⁺ motion in Na₂O·3SIO₂ glass. The lower temperature peak is not affected by any of these electrodes, so it is attributed to the bulk glass. A second and third peak are strongly dependent on the kind of electrode used. A gold anode is a blocking electrode, and a gold cathode, is partially blocking. There is a tendency for a space charge polarization to form when …

Sintering Of Catio₃ With The Addition Of Caco₃ And Lif, Surapol Pleekram

Masters Theses

"The densification of CaTiO₃ with the addition of 4.74, 5.90, 6.88 mol% CaCO₃ and 22 mol% LiF was investigated over the temperature range 800° to 1050°C, for sintering times ranging from 1 to 216 hours. It was found that CaCO₃ reacts with LiF and to form a liquid at a temperature of about 450°C. This liquid enhances the densification of CaTiO₃ . The densification process was followed by making weight loss, shrinkage and porosity measurements. The microstructural development was determined by scanning electron microscope examination of both fractured and polished surfaces. X-ray diffraction and DTA/TGA were …

Dissolution Of Multi-Component Systems, Robin Ashley Murphy

Doctoral Dissertations

"The validity of ideal barrier layer diffusion kinetics was examined in the NaCl/KCl - glycerol and Al₂O₃-CaO-Al₂O₃-SiO₂/slag corrosion systems. Single crystals and dense polycrystalline plates of pure NaCl or KCl exhibit steady-state corrosion rates within 10%, of calculated theoretical values, while dense mixtures of the two salts corrode at rates higher than either pure material. The results are compared to the grooving phenomena of NaCl/KCl bicrystals.

Polycrystalline Al₂O₃ is shown to corrode at the same rate as single crystal sapphire at 1400°C in CaO-SiO₂-Al_{2 …}

Preparation And Properties Of Phosphorus Oxynitride Glasses, Mary R. Reidmeyer

Masters Theses

"The preparation techniques and properties of phosphorus oxynitride glasses produced from sodium metaphosphate and nitride compounds are reported. A preliminary survey of possible nitride additives to sodium metaphosphate is presented along with an extended study of the two most promising nitrides, AIN and Mg₃N₂. Properties reported include: nitrogen content, dissolution rate in water, thermal expansion coefficient, softening point, glass transformation temperature, density, refractive index, microhardness, and infrared absorption"--Abstract, page 1.

Thermally Stimulated Current Studies Of Barium Titanate Capacitors, Patrick Donald Martin

Masters Theses

"Thermally stimulated polarization current (TSPC) and thermally stimulated depolarization current (TSDC) measurements were used to study sample current behavior based on the thermally activated release of trapped charges and polarization mechanisms. Samples studied included laboratory-prepared barium titanate samples (the barium to titanium ratio ranging from 0.96 to 1.04) and commercial ceramic capacitors. Both TSPC and TSDC showed the current spectra of the barium titanate samples were a function of crystal structure and the Ba/Ti ratio. The TSPC/TSDC results of the ceramic capacitors showed differences between capacitor formulations. TSPC/TSDC results also showed differences between good capacitors (physically and electrically) and capacitors …

Thermogravimetric And Electrical Conductivity Studies Of Mg-Doped Lacro₃ And La-Doped Srtio₃, Brian Keith Flandermeyer

Doctoral Dissertations

"Mg-doped LaCrO₃ and La-doped SrTiO₃ are perovskite compounds that display electrical conductivity which is a function of partial pressure of oxygen (po2). It has been proposed that acceptor-doped LaCrO₃ becomes highly resistive at low po2's due to ionic compensation of the acceptor-dopant present by oxygen vacancies. SrTiO₃ has been thought to absorb O₂ into a crystallographic shear structure and exsolve strontium vacancies which can then ionically compensate the La present and give a high resistance at high po2's.

Given these models, relationships between weight loss and conductivity vs. po₂ are developed for both these …

Development Of Glass Microspheres For Radiotherapeutic Applications, Thomas A. Wetteroth

Masters Theses

"Oxide glasses make excellent candidates for radiotherapeutic microspheres used in liver cancer treatment because of their generally high chemical durability and safety of manufacture. From the compositions containing ~5 wt% P₂O₅ studied, magnesium alumino silicate glass microspheres and magnesium alkali silicate glass microspheres with 4 wt% ZrO₂ had acceptably low releases of both elemental phosphorus in deionized water at 50°C, and radioactive ³²P in human blood plasma at 37°C. The relative ranking of glass compositions in the elemental phosphorus leach test shows good agreement with the rankings of compositions in the radioactive ³²P leach …

Glass Formation And Properties In The Gallia-Calcia System, Glenn Whichard

Masters Theses

“The critical cooling rate for glass formation for melts containing from 37.5 to 68.0 mol % Ga₂O₃ varied from 310 ± 80°C/s to 855 ± 115°C/s. The crystallization temperature, microhardness, UV and visible transmission were measured. The density increased from 4.075 g/cm³ at 37.5 3 mol % Ga₂O₃ to 4.402 g/cm³ at 56.0 mol % Ga₂O₃. The refractive index, n_D, increased from 1.778 at 37.5 mol % Ga₂O₃ to 1.802 at 62.0 mol % Ga₂O₃. The IR spectra indicate …

Defect Chemistry Of La-Doped Strontium Titanate, Brian Keith Flandermeyer

Masters Theses

"Thermogravimetric measurements as a function of oxygen activity were performed in the temperature range of 1200°C to 1400°C on a series of La-doped SrTiO₃ compounds. A model postulating the crystallographic accommodation of ionic defects induced by the donor under oxidizing conditions is assumed. Thermodynamic calculations were performed to compare this model to the experimental results with reasonable success"--Abstract, page iii.

Mechanical Properties Of Alumina For Orthopedic Implant Use, Ho Tong Fang

Masters Theses

"The static fatigue, flexural strength and chemical corrosion of three commercially prepared, polycrystalline aluminas, two of orthopedic implant grade, were measured in demineralized water at 37°C and 70°C. The dissolution of a Ca-rich impurity phase, probably a glass, segregated at the grain boundaries and external surface, appears at least partially responsible for the significant difference in static fatigue of these three aluminas. The present results indicate that the minimum static fatigue in demineralized water, and the highest flexural strength in demineralized water and HF solution are both achieved by the alumina characterized by a low concentration of Ca at the …

Sintering Of Lif-Fluxed Srtio₃, Marie-Christine P. Proudian

Masters Theses

"Lithium fluoride (LiF) is used to enhance the sinterability of perovskites, as it results in the formation of a liquid phase. In this study, the mechanism and kinetics of sintering for LiF-fluxed strontium titanate (SrTiO₃) were investigated. The Sr/Ti ratio was varied between 0.98 and 1.03, and the LiF content in the green compact ranged from 0.5 to 2.0 weight percent. Sintering was conducted at temperatures between 695° and 925°C for isothermal dilatometric shrinkage measurements for time intervals of 6000 seconds or less. Weight loss, shrinkage, density and porosity measurements were conducted on samples isothermally sintered between 690° …