Ceramic Materials Commons^™

In-Situ Investigations Of Calcium-Magnesium-Aluminosilicates (Cmas) Infiltration Effects On Thermal Barrier Coatings Under Extreme Environments Replicating Jet Engines, Zachary Stein

Doctoral Dissertations and Master's Theses

Calcium-magnesium-aluminosilicate (CMAS) particulates, such as sand or volcanic ash, are ingested by gas turbine jet engines during operation. When operating within high abundance regions, these particulates negatively interact and degrade the high temperature thermal barrier coatings (TBC) protecting underlying superalloy turbine blades vital to engine operation. These CMAS particulates melt within the engine and infiltrate into the ceramic coatings. In electron-beam physical vapor deposited (EB-PVD) TBCs, the CMAS within the intercolumnar gaps stiffens the coatings and causes thermomechanical induced high stress concentrations, risking crack formation. While molten, the CMAS thermochemically alters and destabilizes the coating, also risking coating failure. Premature, …

Extraction Of Aluminum From Lunar Regolith Through Molten Salt Electrolysis, Jacob N. Ortega, Todd P. Sander, Jeffrey D. Smith, Fateme Rezaei, David J. Bayless, William Schonberg, Daniel S. Stutts, Frank D. Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents the methodology, development, and results of an end-to-end regolith-to-metal concept for producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method. Using electrolytic reduction, aluminum oxide (i.e., alumina) can be reduced into aluminum and oxygen via electrolysis in a molten salt bath. A steady supply of hydrogen chloride could allow this in-situ resource utilization (ISRU) method to supply several necessary materials consumed in the electrolytic reduction step of the process to produce bulk aluminum metal, oxygen, water, and silica from anorthite abundant in lunar highland regions. In this …

Tensile Creep Of A Hybrid Polymer-Matrix/Ceramic-Matrix Composite At Elevated Temperature, Waleed S. Alshehri

Theses and Dissertations

Advanced aerospace systems require structural materials that can perform reliably in high-temperature environments for long durations. The performance of standard polymer matrix composites (PMCs) in these conditions is often limited by their susceptibility to time-dependent deformation, such as creep. The objective of this research is to characterize the high-temperature creep behavior of a novel unitized material system comprising a polymer matrix composite (PMC) and a ceramic matrix composite (CMC) co-cured together. The PMC part consists of the polyimide matrix reinforced with laminated carbon fibers woven in an eight harness satin weave (8HSW). The CMC part consists of a zirconia-based ceramic …

Mno2 Nanoscale Interface Modification, Alexander C. Skoppe

Doctoral Dissertations and Master's Theses

Interface modification of carbon fibers has been shown to improve the mechanical performance of composites. In addition, interface modification of carbon fiber composites can impart multifunctionality into the resulting composite. This work will explore ZnO and MnO2 as interface modifications for use on carbon fibers. When exposed to high temperatures, carbon fibers undergo fiber degradation, leading to the need for low-temperature hydrothermal processes. This work will develop and characterize a nanoscale ZnO and MnO2 interface modification for use on carbon fibers. These nanomodifications will be developed with low-temperature processes, minimizing the fiber degradation that the fibers undergo. Fourier transform infrared …

Ground Testing Of A Magnetic-Electrostatic Separation System For Lunar Regolith Beneficiation, Peter Bachle, Charles Wood, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

The separation of lunar regolith by mineral composition and size category is useful forin-situ resource utilization (ISRU). The research presented herein discusses the designing and development of equipment that has the potential to separate lunar regolith into aluminum, iron-titanium, and magnesium-iron ores. Along with the metal ore separation, this equipment shows the potential to separate regolith by size categories. The combined effect of these separation methods generates output that is valuable to subsequent use in metal and oxygen extraction, additive manufacturing, and regolith sintering processes. The designed equipment uses a dual-strength magnet system with N42 and N52 neodymium magnets for …

Novel Design And Fabrication Of A High-Speed Transient Heat Flux Sensor For Application To Rotating Detonation Engines, Zachary Todd Tallman

Graduate Theses, Dissertations, and Problem Reports (ETD)

Rotating detonation engine (RDE) combustion systems have been a topic of interest in the pressure gain combustion community for their benefits over traditional gas turbine engine combustors. However, cooling requirements for these engines are significantly higher and less predictable than those of non-detonating engines. To understand and quantify the high-speed heat transfer dynamics within an RDE, a novel high-frequency heat flux sensor is presented. This study aims to design a robust, single-sided sensor that can withstand the high temperature and harsh environment of an RDE for extended durations. Screen printing is used to deposit a layered, platinum-yttria-stabilized zirconia (YSZ) film …

Kinetic Modeling Of Dust Grain Dynamics In Electrostatic Sieving, Aaron Berkhoff, Easton Ingram, Fateme Rezaei, Jeffrey Smith, David Bayless, William Schonberg, Daoru Han

Chemical and Biochemical Engineering Faculty Research & Creative Works

A new kinetic particle modeling framework was developed to investigate electrostatic transport of lunar regolith dust particles with applications to the concept of electrostatic sieving. the new approach is based on kinetic particle dynamics and includes major modules of sampling the particle size distribution, solving electric fields, and tracking motion of charged dust grains. a case study for a concept of electrostatic sieving was chosen to validate the new model. the simulation achieved similar performance of particle size classification as reported in the literature. the new model is computationally efficient (takes a few minutes on a PC-type laptop computer) so …

Tension–Compression Fatigue Of A Hybrid Polymer-Matrix/Ceramic-Matrix Composite At Elevated Temperature, Marina B. Ruggles-Wrenn, Joshua Schmidt

Faculty Publications

Fully reversed tension–compression fatigue of a hybrid material comprising polymer matrix composite (PMC) co-cured with a ceramic matrix composite (CMC) was investigated. The PMC portion had a polyimide matrix reinforced with 15 plies of carbon fibers woven in an eight-harness satin weave (8HSW). The CMC portion had three plies of a quartz-fiber 8HSW fabric in a zirconia-based ceramic matrix. The hybrid PMC/CMC was developed for use in aerospace thermal protection systems (TPS). Hence, the experimental setup aimed to simulate the TPS service environment—the CMC side was kept at 329 °C, whereas the PMC side was open to laboratory air. Compression …

Influence Of Environmental Barrier Coatings On The Overall Effectiveness Of A Film Cooled Ceramic Matrix Composite Plate, Shane P. Lindsay

Theses and Dissertations

Silicon carbide ceramic matrix composites, a promising new potential upgrade over the conventional metals currently used for jet engine turbine blades, have a propensity to oxidize in a combustion environment. Engine manufacturers often apply environmental barrier coatings to prevent the composites from oxidizing. What is unclear, however, is how environmental barrier coatings effect underlying composite temperatures. This research examined the coatings’ effects by first characterizing the influence of environmental barrier coatings on the underlying temperature of a protected ceramic, then evaluating the significance of lateral conduction for cooling a coated ceramic, and finally comparing cooling results for coated and uncoated …

Electrostatic Sorting Of Lunar Regolith Simulants For Sustainable Resource Utilization: Modeling And Characterization Of Particle Size Distribution, Abdullah Al Moinee, Peter Bachle, Kyle Newport, William Schonberg, David Bayless, Jeffrey Smith, Daoru Han, Fateme Rezaei

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In pursuit of sustainable resource utilization on the Moon, this paper delves into modeling and characterization of particle size distribution (PSD) of lunar regolith simulants in an electrostatic system. A prototype electrostatic sieve was built and tested with four sample simulants mirroring properties of lunar mare and highland regolith. An alternating four-phase (90 degrees, 180 degrees, 270 degrees, 360 degrees) traveling square-wave was utilized for particle-directed transport to model the diverse trajectories of the particles. Numerically, we scrutinized how the distribution functions of the particles are manifested as the electrostatic field propagates, with a focus on three distinct particle ranges …

Kinetic Modeling Of Electrostatic Sieving For Lunar Regolith Beneficiation: Case Studies, Easton Ingram, Emmanuela Amen Eze, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

A new kinetic particle modeling framework was developed to investigate electrostatic transport of lunar regolith particles with applications to the concept of electrostatic sieving. the new approach is based on kinetic particle dynamics and includes major modules of sampling the particle size distribution, solving electric fields, and tracking motion of charged dust grains. Case studies for a concept of electrostatic sieving were chosen to validate the new model. the simulation achieved similar yields reported in previous works, which served as validation of the model. the new model is computationally efficient and could serve as a design, analysis, and optimization tool.

Progress Of Lisap-Mse: A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, David Bayless, Daniel Stutts, Daoru Han, Todd P. Sander, Jeffrey Smith, Fateme Rezaei, William Schonberg

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Electrostatic Sorting Of Lunar Regolith Simulants For Sustainable Resource Utilization: Modeling And Characterization Of Particle Size Distribution, Abdullah Al Moinee, Peter Bachle, Kyle Newport, William Schonberg, David Bayless, Jeffrey Smith, Daoru Han, Fateme Rezaei

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In pursuit of sustainable resource utilization on the Moon, this paper delves into modeling and characterization of particle size distribution (PSD) of lunar regolith simulants in an electrostatic system. a prototype electrostatic sieve was built and tested with four sample simulants mirroring properties of lunar mare and highland regolith. an alternating four-phase (90 degrees, 180 degrees, 270 degrees, 360 degrees) traveling square-wave was utilized for particle-directed transport to model the diverse trajectories of the particles. Numerically, we scrutinized how the distribution functions of the particles are manifested as the electrostatic field propagates, with a focus on three distinct particle ranges …

Magnetic Separation Of Lunar Regolith Simulants With Applications To In Situ Resource Utilization On The Moon, Peter Bachle, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

The development of in situ resource utilization (ISRU) for metal extraction is imperative as a steppingstone for habitation construction in lunar and non-terrestrial environments. Separation of minerals by chemical composition is important to optimize metal and oxygen liberation from lunar ore. to this effect, devices capable of separating aluminum bearing minerals from iron-bearing minerals from the lunar regolith simulants have been developed. Twenty-eight different simulants have been used in this study. a dual-belt separator was designed to reduce middlings. Para-magnetic minerals were reliably separated using a neodymium N52-magnet-separator system. Effective separation of aluminum-bearing minerals from iron-bearing minerals was greater than …

A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daniel Stutts, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Ambient Temperature Strength Degradation Of A Ceramic Matrix Composite Due To Solid Particle Erosion, Jonathan Clawson

Williams Honors College, Honors Research Projects

Solid particle erosion (SPE) is an issue for aircraft exposed to hard, fine particles, such as sand or dust, that can be ingested into the engine at a high velocity without reaching their melting point, resulting in material removal. SPE can be attributed to the intake of particulate debris from the runway or from airborne particulates. The cumulative mass loss from SPE damage affects the structural integrity and performance of the engine; however, its effects on ceramic matrix composites (CMCs), that are being employed in the aerospace industry, are not well understood in literature. The limited SPE research studies that …

Creep Behavior And Deformation Mechanisms Of Spark Plasma Sintered Oxide Ceramics For Aerospace Systems At 1300˚C - 1400˚C, David D. Swanson

Theses and Dissertations

The mechanical behavior of YAG and LuAG was investigated at elevated temperatures. The specific materials investigated in this work include high-purity, polycrystalline YAG, high-purity, polycrystalline LuAG, and two doped variants of YAG: 2at% Yb-doped, polycrystalline YAG and 2at% Er-doped, polycrystalline YAG. Several billets of each material were prepared and processed by means of spark plasma sintering (SPS). Many different sintering parameters were utilized in order to obtain materials with various physical properties and to identify the effects of sintering parameters on the average grain size of the resulting materials. The compressive creep behavior of these materials was investigated at 1300°C …

Review: Factors Affecting Composite Laminates Against Lightning Strikes, Aaryan Manoj Nair

Publications and Research

Lightning strike protection (LSP) have recently been a newly developing field particularly with the emergence of graphene thin film integration into carbon fiber composite structures. This technology has a widespread application in airplanes, wind turbines, and other instruments which are susceptible to frequent lightning strikes. Electrical discharge of the instrument in a safe manner is vital for the safety of the passengers (in the case of flights) as well as the integrity of the aircraft structures because of their specific mechanical and structural properties, which are essential for their functioning. The purpose of the study is to fabricate graphene thin …

Static Fatigue Of Hi-Nicalon™ S Ceramic Fiber Tows At 600°C In Air And Silicic Acid-Saturated Steam, Caleigh M. Nelson

Theses and Dissertations

Ceramic matrix composites (CMCs) have the potential to be utilized in applications such as hypersonic vehicles, aircraft leading edges, hot sections of engines, and rocket nozzles. Of particular interest are advanced SiC/SiC composites that can withstand the elevated temperatures and harsh oxidizing environments while maintaining their properties and structural integrity under an applied load. Steam, a major component of combustion environment, is one such aggressive oxidizing environment. As steam passes through the SiC/SiC composite, entering the composite interior through the cracks in the SiC matrix, it becomes saturated with silicic acid, Si(OH)₄. Before incorporating SiC/SiC composites in the …

Fatigue Of Two Oxide/Oxide Ceramic Matrix Composites At 1200°C In Air And In Steam. Effect Of Diamond Drilled Effusion Holes, Anthony R. Cabri

Theses and Dissertations

The tension-tension fatigue behavior of two oxide-oxide ceramic matrix composites (CMCs) was investigated at 1200°C in laboratory air and steam. Both composites consist of a porous oxide matrix reinforced with laminated, woven mullite/alumina (NextelTM720) fibers. The first composite had an alumina matrix, while the second had an alumina-mullite matrix. First, we assessed the effects of incorporating mullite into the matrix material on fatigue performance by studying the tension-tension fatigue behavior of alumina-mullite matrix CMC. Second, we evaluated the effects of effusion holes on the alumina matrix CMC's fatigue performance. Specimens containing an array of 17 effusion holes of 0.5-mm diameter …

Interlaminar Damage Detection In Composite Materials, Hariharan Rangarajan

Williams Honors College, Honors Research Projects

Using ceramic matrix composites (CMCs) for high-temperature applications in jet engines increases durability and reduces weight and cooling requirements resulting in improved efficiency and fuel savings. Understanding, detecting, and monitoring different types of damage is essential to achieve optimal performance of CMC components. The Direct Current Potential Drop (DCPD) method is a non-destructive technique of estimating damage in composite materials.

DCPD technique works by measuring nodal potential differences when current is flown through the material. Direct current spreading in different woven and laminate composites is modeled to follow a ladder resistor network in which the nodal voltages decrease exponentially as …

Creep Of Hafnium Diboride -20 Vol% Silicon Carbide At 1500°C In Air, Glen E. Pry

Theses and Dissertations

Refractory metal borides, commonly referred to as Ultra High Temperature Ceramics (UHTCs), exhibit a number of unique properties, such as extremely high melting temperature and hardness, chemical stability, high electrical and thermal conductivity and corrosion resistance. It has been demonstrated that the addition of SiC improves the oxidation resistance of ZrB2- and HfB2-based UHTCs above 1200°C by modifying the composition of the oxide scale. Addition of SiC retards the oxidation rate of ZrB2 and HfB2 by forming a protective layer of borosilicate glass. Creep deformation is one of the critical criterion for structural application of ceramics at elevated temperatures. Compression …

Optimal Sintering Temperature Of Ceria-Doped Scandia Stabilized Zirconia For Use In Solid Oxide Fuel Cells, Amanda K. Assuncao

Honors Undergraduate Theses

Carbon emissions are known to cause decay of the Ozone layer in addition to creating pollutant, poisonous air. This has become a growing concern among scientists and engineers across the globe; if this issue is not addressed, it is likely that the Earth will suffer catastrophic consequences. One of the main culprits of these harmful carbon emissions is fuel combustion. Between vehicles, power plants, airplanes, and ships, the world consumes an extraordinary amount of oil and fuel which all contributes to the emissions problem. Therefore, it is crucial to develop alternative energy sources that minimize the impact on the environment. …

Creep Of Hi-Nicalon™ S Ceramic Fiber Tows At 700°C In Air And In Silicic Acid-Saturated Steam, Matthew W. Piper

Theses and Dissertations

Aircraft structural and engine components are subjected to elevated temperature and steam environments during operation. Turbine blades experience particularly harsh conditions that are approaching the operating temperature limits of current Nickel-based superalloys even with active cooling. Ceramic matrix composites (CMCs), which demonstrate high specific strength and specific stiffness and maintain these properties at elevated temperatures such that active cooling is not required, are prime candidates to replace superalloys as the materials for turbine blades. Ceramic matrix composites are composite materials that consist of a ceramic matrix with fiber reinforcement. This research investigated a silicon carbide (SiC) fiber, Hi-Nicalon™ S, which …

Studies Of Dynamic Crack Propagation And Crack Branching With Peridynamics, Youn Doh Ha, Florin Bobaru

Department of Engineering Mechanics: Faculty Publications

In this paper we discuss the peridynamic analysis of dynamic crack branching in brittle materials and show results of convergence studies under uniform grid refinement (m-convergence) and under decreasing the peridynamic horizon (δ-convergence). Comparisons with experimentally obtained values are made for the crack-tip propagation speed with three different peridynamic horizons.We also analyze the influence of the particular shape of themicro-modulus function and of different materials (Duran 50 glass and soda-lime glass) on the crack propagation behavior. We show that the peridynamic solution for this problem captures all the main features, observed experimentally, of dynamic crack propagation and branching, as well …

Effects Of Environment On Creep Behavior Of Nextel720/Alumina-Mullite Ceramic Composite With ±45º Fiber Orientation At 1200ºc, Muzaffer Ozer

Theses and Dissertations

The present effort will investigate the off-axis creep behavior of the Nexte720/Alumina-Mullite CMC, a material system which relies on a porous alumina/mullite matrix for damage tolerance as compared to the pure alumina matrix in earlier studies. This research evaluated the creep behavior of N720/AM with a ± 45° fiber orientation at 1200°C in: laboratory air, steam, and argon environments. Creep-rupture tests at the creep stress levels of: 32, 30, 26, and 20 MPa were conducted in each environment. Additionally 35 MPa stress level examined in air and 13 MPa stress level examined both in air and steam. The N720/AM with …