Ceramic Materials Commons^™

Lafe0.925ti0.075o3 Perovskite Coated With Ethyl Cellulose: A High-Stability, Low-Hysteresis Platform For Advanced Humidity Sensing, Akhmad Futukhillah Fataba Alaih, Djoko Triyono, Rifqi Almusawi Rafsanjani

Makara Journal of Science

Humidity sensors are pivotal in numerous sectors, such as environmental monitoring, industrial automation, and health-care. This study presents the fabrication and detailed evaluation of an advanced humidity sensor using ethyl cellulose (EC)-coated LaFe_0.925Ti_0.075O₃ (LFTO) perovskite nanoparticles synthesized via the sol-gel method. The LFTO nanopar-ticles exhibited a mesoporous structure with an enhanced surface area, which significantly improved their moisture adsorption capabilities. The innovative application of EC coating addresses critical substrate adhesion issues, enhancing mechanical stability without compromising sensor sensitivity. Comprehensive performance evaluations revealed minimal hysteresis (

Microstructural Evolution Of Zirconium Diboride Irradiated With 5–10 Mev Au Ions At Room Temperature And 570 °C, Narrie Loftus, José Olivares, Miguel Crespillo, Esther Enríquez Pérez, Jeremy Watts, Eric W. Bohannan, Gregory Hilmas, William Fahrenholtz, Joseph Graham

Materials Science and Engineering Faculty Research & Creative Works

Zirconium diboride was irradiated with 5 MeV Au^2 + , 7 MeV Au⁴⁺ and 10 MeV Au³⁺ ions at room temperature and 570 °C to doses from 1 to 8 displacements per atom (dpa). Grazing incidence X-ray diffraction (GIXRD) analysis revealed no secondary phase formation. Rietveld analysis of the GIXRD data indicated an accumulation of microstrain at low dpa and room temperature. Dislocations observed in transmission electron microscopy (TEM) cross-sections are likely the main contributor to the microstrain. High dpa and high-temperature samples exhibit lower lattice distortion than lower dpa samples, suggesting the presence of enhanced defect …

Raw Data For The Manuscript "Silicon-Stabilized Three-Dimensional Covalent Networks In High Entropy Diborides", Michael Yeung, Reza Mohammadi

Chemistry Department Faculty Scholarship

Abstract for data:

Raw data for the journal publication, Silicon-stabilized three-dimensional covalent networks in high entropy diborides. ReadMe file provided.

Abstract for Journal publication: 

High entropy ceramics offer a pathway to stabilize unconventional chemistries beyond traditional alloying rules. We report the incorporation of silicon into an AlB₂-type high entropy diboride, Cr_0.2Nb_0.2Si_0.2Ta_0.2Ti_0.2B₂, despite silicon violating classical Hume-Rothery rules for alloying. Arc melting produced a phase-pure, chemically homogeneous structure, as confirmed by powder X-ray diffraction (pXRD) and scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM–EDS). Silicon occupies …

Elucidating The Effects Of Water Activity On The Hydration Kinetics And Thermodynamics Of Ye’Elimite–Calcium Sulfate Hydrate Systems, Godwin I. Ogbuehi, Rupack R. Halder, Aditya Kumar, Gaurav Sant, Monday U. Okoronkwo

Materials Science and Engineering Faculty Research & Creative Works

Relative humidity and water activity (aH) reductions have been known to suppress the hydration of anhydrous cement clinker phases. However, the relationship between ye'elimite (C4A3$) hydration kinetics and water activity remain unclear. This study employs experimental and thermodynamic modeling approaches to investigate the influence of water activity on ye'elimite hydration in the "C4A3$ + water", and "C4A3$ + gypsum + water" systems. Experimental findings indicate that as water activity decreases, C4A3$ hydration diminishes until the reaction is brought to a halt at a threshold aH. The critical aHand corresponding solubility constant of C4A3$ (KC4A3S¯) estimated from thermodynamic analysis are 0.46 …

Antibacterial Activity Of Zno/Geopolymer Composite Granules And Their Potential Application In Water Treatment, Ziyan Tirta Maulitia, Putri Nur Angelina, Pipit Erlita Sari, Sri Sugiarti, Irma Isnafia Arief, Zaenal Abidin

Makara Journal of Science

Water pollution has become a major global concern owing to its complexity and widespread impact. Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli) are the most common bacterial contaminants in water sources, which pose significant threats to public health. To mitigate water contamination by these pathogenic microorganisms, developing and implementing effective water treatment technologies are essential. A promising approach involves using antibacterial water filtration systems. Herein, zinc oxide (ZnO) nanoparticles were synthesized via hydrothermal and precipitation methods as antibacterial agents for water treatment. These preparation methods required considerably low synthesis time. A capping agent was …

The Evolution Of Nanoparticles In Nanoparticle Doped Optical Fibers, Mary Cahoon

All Dissertations

Optical fiber and fiber laser technologies based on silica glass are critical to many technologies today. One method to improve the optical performance of laser fibers is engineer the local environment around the active elements in the glass. To that end, this Dissertation focused on the fabrication and characterization of fibers made with nanoparticles incorporated into the glass to control the local composition. First, the nanoparticle composition and structure was analyzed as it evolved from from the initially-synthesized form to incorporation into the dense aluminum-silicate glass. The aluminum oxide in the glass was found to be important not only to …

Synergy In Materials: Leveraging Phosphosilicate Waste Forms For Electrochemical Salt Waste, Jonathan S. Evarts, Brian J. Riley, Charmayne E. Lonergan, Michaella S. Harris, Jincheng Bai, Eric W. Bohannan, Iheanyichukwu Ajoku, Saehwa Chong, John S. Mccloy

Materials Science and Engineering Faculty Research & Creative Works

Waste forms containing glassy and crystalline phosphate and silicate phases were produced to immobilize salt waste simulants from pyro processing and characterized by using Raman spectroscopy, Mössbauer spectroscopy, X-ray diffraction, scanning electron microscopy, heat capacity, and chemical durability measurements. In this work, a phosphosilicate waste form is presented to leverage the benefits of both borosilicate glasses and iron phosphate glasses. To improve waste loading, prior to immobilization, salt simulants were successfully dechlorinated using ammonium dihydrogen phosphate, mixed with a borosilicate frit (5–30 wt. %) and Fe2O3, and vitrified. Additions of 2.5–15 wt. % borosilicate glass (NBS3) improved normalized release rates …

Effect Of Niobium Dopant On Zno Thin Films Prepared Via The Sol–Gel Spin Coating Method, Kevin Alvin Eswar, Nur Fairuz Rostan, Maryam Mohamad, Rabiatuladawiyah Md Akhir, Rosfayanti Rasmidi, Muliyadi Guliling, Najwa Ezira Azhar, Irmaizatussyehdany Buniyamin, Mohd Firdaus Malek, Mohamad Rusop Mahmood, Husairi Fadzilah Suhaimi, Saifollah Abdullah

Makara Journal of Science

Thin films of zinc oxide (ZnO) and niobium (Nb)-doped ZnO were deposited on a glass substrate using the sol–gel spin coating method. Diethanolamine, isopropyl alcohol, and zinc acetate served as the stabilizers, solvent, and starting ma-terial, respectively. Niobium pentachloride was employed as the dopant source. Energy-dispersive X-ray analysis con-firmed Nb incorporation. Field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), and ultravio-let–visible spectroscopy (UV–Vis) analyses characterized the morphology, structure, and optics of the films, respective-ly. Both films, comprising nanoparticles, were visible in FESEM. Nb doping reduced the particle size from 44.2 nm to 35.8 nm. The XRD peaks at 31.23°, …

Secondary Electron Yield Of Metals, Alloys, And Metal Oxides From First Principles Based Monte Carlo Simulations, Raul E. Gutierrez

Electrical and Computer Engineering ETDs

Density Functional Theory (DFT) based Monte Carlo (MC) simulations of the Sec-
ondary Electron Yield (SEY) of metals, alloys, and metal oxides are performed to
find material properties that could help reduce or influence the multipactor effect.
In order to accurately model the SEY of materials, knowledge of the frequency- and
momentum-dependent Energy Loss Function (qDepELF) is required. The qDepELF
is difficult to determine from experiment; however, it can be calculated from first
principles. The DFT-MC approach for simulating the secondary electron genera-
tion, propagation, and emission processes is described herein. Material properties,
which are calculated using DFT and used …

Advancements In Characterization Of Ancient Potteries From Southeast Asia: A Review Of Analytical Techniques, Chitnarong Sirisathitkul

Makara Journal of Science

Ancient potteries offer valuable information regarding technological advancements, life dynamics, cultural diversity, and trade routes in the past. Earthenware, stoneware, and porcelain from Southeast Asia have been characterized using several analytical techniques, as reviewed in this article. Fluorescent and diffracted X-rays give rise to elemental and phase compositions, respectively. Examination of molecular bonds requires vibrational spectroscopy, which is useful for the identification of organic materials in ancient potteries. With the advent of portable X-ray fluorescence and Raman spectrometry, on-site analysis of archeological ceramics is now possible. For in-depth analysis, synchrotron light sources can provide new insights into artifacts through X-ray …

Mechanisms Of Dendritic Shorting In Lithium Metal Batteries With Li7la3zr2o12 Solid Electrolytes, Lukas Karapin-Springorum

Pomona Senior Theses

Energy storage will play a crucial role in efforts to mitigate the effects of climate change caused by greenhouse gas emissions from human activity. Lithium metal batteries using solid electrolytes like Li₇La₃Zr₂O₁₂ have higher energy density than lithium-ion batteries, which may enable a more rapid and complete electrification of transportation. However, lithium metal batteries suffer from undesirable short-circuiting when metallic lithium deposits connect the two electrodes. It has been debated whether these lithium dendrites generally grow directionally from the anode or are generated by the reduction of lithium ions inside the solid electrolyte, …

Processing, Stability, And High-Temperature Properties Of Doped Lacro3-Based Refractory Ceramics And Composites For Harsh Environments Sensing Applications, Javier A. Mena

Graduate Theses, Dissertations, and Problem Reports (ETD)

In order to test and monitor the operational stability and conditions of various energy, transportation, and manufacturing systems and their components, accurate sensors capable of operating at temperatures over 1000 °C in various environments for long durations are required. In addition, many of these harsh environmental systems do not permit sensors to be directly inserted into the environment, so the sensors need to be embedded into the surrounding support or thermal protective materials. Some technological and industrial applications that require the use of harsh environment conditions sensing include nuclear and chemical reactors, jet engines, heavyduty gas turbines, rotating bearings in …

Modeling, Fabrication, And Characterization Of Rf-Based Passive Wireless Sensors Composed Of Refractory Semiconducting Ceramics For High Temperature Applications, Kavin Sivaneri Varadharajan Idhaiam

Graduate Theses, Dissertations, and Problem Reports (ETD)

Real-time health monitoring of high temperature systems (>500^oC) in harsh environments is necessary to prevent catastrophic events caused by structural failures, varying pressure, and chemical reactions. Conventional solid-state temperature sensors such as resistance temperature detectors (RTDs) and thermocouples are restricted by their operating environments, sensor dimensions and often require external power sources for their operation. The current work presents the research and development of RF-based passive wireless sensing technology targeting high temperatures and harsh environmental conditions. Passive wireless devices are generally classified as near-field and far-field devices based on the interrogation distance. Near-field sensors are placed at …

Mxenes As Flow Electrodes For Capacitive Deionization Of Wastewater, Naqsh E. Mansoor

Boise State University Theses and Dissertations

The energy-water nexus poses an integrated research challenge, while opening up an opportunity space for the development of energy efficient technologies for water remediation. Capacitive Deionization (CDI) is an upcoming reclamation technology that uses a small applied voltage applied across electrodes to electrophoretically remove dissolved ionic impurities from wastewater streams. Similar to a supercapacitor, the ions are stored in the electric double layer of the electrodes. Reversing the polarity of applied voltage enables recovery of the removed ionic impurities, allowing for recycling and reuse. Simultaneous materials recovery and water reclamation makes CDI energy efficient and resource conservative, with potential to …

Study Of Amorphous Boron Carbide And Hydrogenated Boron Carbide Materials Using Molecular Dynamics And Hybrid Reverse Monte Carlo, Rajan Khadka

Graduate Theses/Dissertations

We present a computational study of amorphous boron carbide (a-B_xC) models using Molecular Dynamics (MD) studied with Stillinger-Weber (SW) and ReaxFF potential. The atomic structure factor (S(Q)), radial distribution function (RDF) and bond lengths comparison with other experimental and ab initio models shows that a random arrangement of icosahedra (B₁₂, B₁₁C) interconnected by chains (CCC, CBC) are present in a-B_xC. Afterward, Hybrid Reverse Monte Carlo (HRMC) technique is used to recreate a-B_xC structures. The existing SW potential parameters of Boron are optimized for the α-rhombohedral (Icosahedral B_{12 …}

Nano Fab Lab 63, Brian K. Deemer, Josh Clemons, Nick Brodine, Delaney Fitzsimmons

Mechanical Engineering

Lawrence Livermore National Laboratories (LLNL) has several steps in the production process for ceramic nanofiber tubes that they would like to improve - electrospinning, cutting, rolling, sealing and heat treating. We undertook the challenge to deliver LLNL with a semi-automated process that efficiently integrates the steps of cutting, rolling, and sealing to save time and improve control over end dimensions. In this document, we discuss the technical background of the manufacturing steps currently followed to create nanofiber tubes, identify which steps are incorporated in our prototype and explain how they will interface with one another, define the design requirements, present …

Synthesis And Characterization Of Dielectric And Multiferroic Nanocrystalline Transition Metal Oxide Materials And Nanocomposites, Frederick A. Pearsall

Dissertations, Theses, and Capstone Projects

Nanocrystalline transition metal oxides with unique chemical, physical, magnetic and dielectric properties have very broad applications, ranging from photocatalysis, capacitor energy storage and 4-state memory. Frequency stable, high permittivity nanocomposite capacitors produced under mild processing conditions offer an attractive replacement to MLCCs derived from conventional ceramic firing. In one project reported herein, 0-3 nanocomposites were prepared using BaTiO₃ (barium titanate, BTO) nanocrystals, suspended in a poly(furfuryl alcohol) matrix, resulting in a stable, high effective permittivity, low and stable loss dielectric. Effective medium approximations were used to compare this with similar nanocomposite systems. The use of synthesized BTO nanocrystal photocatalysts …

Creep Of Nextel 720/Alumina Ceramic Matrix Composite With Diamond-Drilled Effusion Holes At 1200°C In Air And In Steam, Megan L. Harkins

Theses and Dissertations

A recent study evaluated tensile stress-strain and tensile creep behavior of an oxide-oxide composite (Nextel™720/alumina) with laser-drilled effusion holes at 1200°C. It was determined that the presence of laser-drilled holes degraded the mechanical properties and performance of the CMC as a result of damage caused to the composite microstructure by the laser drilling process. Based on these results, the present effort sought to assess the effects of diamond-drilled holes on the mechanical behavior of this CMC. Tensile properties of the N720/A composite at 1200°C in laboratory air were unaffected by the presence of an array of 17 diamond-drilled effusion holes. …

Metallic Systems At The Nano And Micro Scale: Bimetallic Nanoparticles As Catalysts And Mcraly Bond Coats In Thermal Barrier Coatings, Kenneth Kane

Theses and Dissertations

The dissertation is split into two parts. The first part will be focused on changes in material properties found at the nanoscale, as miscibility and electronic structure can change significantly with size. The formation of classically-immiscible bimetallic nanoparticles (BNPs) becomes favorable at the nanoscale and novel catalytic properties can emerge from the bimetallic alloying. The formation of alloyed and non-alloyed BNPs is achieved through pulse laser ablation (PLA) and a significant increase in catalytic activity is observed for both. Recently discovered, the increased activity in the non-alloyed BNPs, deemed multicomponent photocatalysis, is examined and the proposed mechanism discussed. The second …

Polyhedral Oligomeric Silsesquioxane-Phosphate Glass Matrix Nanocomposites With Additional Chapter On Phosphate Glass-Poly(Ethylene Terephthalate) Matrix Composites, Kyoungtae Kim

Dissertations

Preparation and characterization of tin fluorophosphate glass (Pglass) matrix nanocomposites incorporating polyhedral oligomeric silsesquioxane (POSS) were investigated on the structural, thermal, morphological, mechanical, and rheological properties. Various processes including synthesis, extrusion and sintering processes were applied to prepare the nanocomposite samples. Another application of POSS with hydrophobic functional groups on the well-structured nanoscale silicate cage with three silanol groups was investigated to present the feasibility to use POSS molecule as a coating material on the surface of the hydrophilic inorganic glass. In addition, Poly(ethylene terephthalate) polymer matrix composites incorporating Pglass was studied to present the benefits of the Pglass with …

Surfactant Driven Assembly Of Freeze-Casted, Polymer-Derived Ceramic Nanoparticles On Grapehene Oxide Sheets For Lithium-Ion Battery Anodes, Ali Zein Khater

Honors Undergraduate Theses

Traditional Lithium-Ion Batteries (LIBs) are a reliable and cost-efficient choice for energy storage. LIBs offer high energy density and low self-discharge. Recent developments in electric-based technologies push for replacing historically used Lead-Acid batteries with LIBs. However, LIBs do not yet meet the demands of modern technology. Silicon and graphene oxide (GO) have been identified as promising replacements to improve anode materials. Graphene oxide has a unique sheet-like structure that provides a mechanically stable, light weight material for LIB anodes. Due to its structure, reduced graphene oxide (rGO) is efficiently conductive and resistive to environmental changes. On the other hand, silicon-based …

Charge Transport In Electronic-Ionic Composites, Long Zhang

Theses and Dissertations--Chemical and Materials Engineering

The goal of this thesis is to generate fundamental understandings of charge transport behaviors of composites consisting of garnet structured Al substituted Li₇La₃Zr₂O₁₂ (LLZO) electrolyte and LiCoO₂ electrode. In order to take full advantage of all-solid-state batteries, bulk type composite electrodes should be introduced to increase energy and power density. However, the charge utilization of bulk type composite electrodes is quite low. Understanding ionic conduction behavior is, therefore, important for improving the performance of all-solid-state batteries, because ion conduction within solids depends on effective pathways. Electronic conductivity can be easily compensated by …

Selection Of The Process Parameters For The Mass Plating Of Discrete Electronic Components, Ann Hopper

Articles

The miniaturisation of electronic components coupled with requirements for high temperature lead free soldering has forced the improvement of the termination finish of surface mount components to meet the critical demands of the electronic industry. In the present work the processing parameters necessary to plate miniature multilayer varistors (MLV’s) have been explored. The tooling selected was a “Rotary flow-thru’ plater” which achieved high volume plating with

Impedance Analysis Of Dielectric Nanoparticles Enabled Via A Self-Assembled Monolayer, Sasidhar Siddabattuni, Thomas P. Schuman, Vladimir Petrovsky, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

Impedance spectroscopy has been shown to be a powerful tool to investigate the dielectric characteristics of powders suspended in suitable liquids. The electrical and dielectrical contributions of different components of the slurry can be extracted from the impedance spectra through measurement of frequency-dependent relaxations. However, for ferroelectric powders that possess innate surface conductivity, such as BaTiO₃, nanoparticles have sufficient conductivity to exclude low frequency fields that preclude impedance characterization of the particle core. In this work, the slurry technique is shown to be effective for dielectric characterization of not only micrometer-sized particles through equivalent circuit modeling but also …

Dielectric Properties Of Polymer–Particle Nanocomposites Influenced By Electronic Nature Of Filler Surfaces, Sasidhar Siddabattuni, Thomas P. Schuman, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

The interface between the polymer and the particle has a critical role in altering the properties of a composite dielectric. Polymer-ceramic nanocomposites are promising dielectric materials for many electronic and power devices, combining the high dielectric constant of ceramic particles with the high dielectric breakdown strength of a polymer. Self-assembled monolayers of electron rich or electron poor organophosphate coupling groups were applied to affect the filler–polymer interface and investigate the role of this interface on composite behavior. The interface has potential to influence dielectric properties, in particular the leakage and breakdown resistance. The composite films synthesized from the modified filler …

Development Of Microbial And Enzymatic Fuel Cells For Bio-Inspired Power Sources, Fatih Dogan, Shelley Minteer

Materials Science and Engineering Faculty Research & Creative Works

This report is based on some of the revolutionary concepts described in the Road Map on Bioinspired Power Systems within the AFRLRW Campus Challenge II. Development of biofuel cell concepts integrated with fuel regeneration and energy storage capabilities are proposed to create a compact and self-sustaining power system. The first part of this work identified a sediment based microbial fuel cell that could power small electronics and maintain electrical activity over long periods of time. AFRLRW does not feel that this work adequately addresses the original scope nor does it provide a basis on which to continue work. The second …

Influence Of Magnesium Nitrate On The Corrosion Performance Of Sol-Gel Coated Aa2024-T3 Aluminium Alloy, Rajath Varma, Brendan Duffy, John Cassidy

Articles

Traditional anti-corrosion technology has relied heavily on using reducible metal species, predominantly hexavalent chromium (Cr(VI)), for protecting reactive metal alloys such as aluminium which is extensively used in the aerospace sector. However, the impending changes in the use of Cr(VI) in Europe and the United States have forced aerospace manufacturers to examine alternative materials for protecting aluminium. One of the most promising alternatives being investigated are organosilane based sol-gels containing anticorrosion additives. In this work the anti-corrosion properties of magnesium (II) nitrate (Mg(NO3)2) as a inhibitor was investigated at different concentrations (0.1% - 1.0 wt %) in a methyltriethoxysilane (MTEOS) …

Yttrium And Hydrogen Superstructure And Correlation Of Lattice Expansion And Proton Conductivity In The Bazr0.9y0.1o2.95 Proton Conductor, A. Braun, A. Ovalle, V. Pomjakushin, A. Cervellino, S. Erat, Wayne C. Stolte, T. Graule

Chemistry and Biochemistry Faculty Research

Bragg reflections in Y-resonant x-ray diffractograms of BaZr_0.9Y_0.1O_2.95 (BZY10) reveal that Y is organized in a superstructure. Comparison with neutron diffraction superstructure reflections in protonated/deuterated BZY10 suggests that both superstructures are linked, and that protons move in the landscape imposed by the Y. The thermal lattice expansion decreases abruptly for protonated BZY10 at T≥648±20 K, coinciding with the onset of lateral proton diffusion and suggesting a correlation of structural changes and proton conductivity. The chemical shift in the Y L₁-shell x-ray absorption spectra reveals a reduction from Y³⁺ toward Y²⁺ upon …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix, Kenneth Czerwinski

Fuels Campaign (TRP)

This project will examine inert fuels containing ZrO₂ and MgO as the inert matrix. Ceramics with this inert matrix, Ce, U and eventually Pu will be synthesized and examined. While the Advanced Fuel Cycle Initiative focus is on inert fuels with Pu as the fissile component, this task will perform initial laboratory experiments with Ce and U. The initial work with Ce will be performed early in the project with results used as a basis for U studies. Reactor physics calculations will be used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf. …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix, Kenneth Czerwinski

Fuels Campaign (TRP)

This project will examine inert fuels containing ZrO₂ and MgO as the inert matrix. Ceramics with this inert matrix, Ce, U and eventually Pu will be synthesized and examined. While the Advanced Fuel Cycle Initiative focus is on inert fuels with Pu as the fissile component, this task will perform initial laboratory experiments with Ce and U. The initial work with Ce will be performed early in the project with results used as a basis for U studies. Reactor physics calculations will be used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf. …