Ceramic Materials Commons^™

Thermo-Mechanical Behaviour Of Metal-Coated Optical Fibers For Distributed High-Temperature Sensing: From Laboratory Characterization To Industrial Case Validation, Koustav Dey, Rony Kumer Saha, Bohong Zhang, Laura Bartlett, Jeffrey D. Smith, Ronald J. O'Malley, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

Reliable distributed temperature sensing in high-temperature environments remains a significant challenge due to the thermal and mechanical limitations of conventional optical fibers. In particular, polymer-coated fibers degrade above ∼300 °C due to coating failure, mechanical fragility and hydrogen ingress. Metal-coated optical fibers offer a robust alternative for harsh environments such as Electric Arc Furnaces (EAFs), aerospace engines, nuclear systems, and oil and gas wells, owing to their superior mechanical strength and hermetic sealing. In this work, a first comprehensive experimental investigation of the thermo-mechanical behavior of metal-coated optical fibers for distributed high temperature sensing is presented over a wide temperature …

Analysis Of Tower Stringset Replacement From 33 Kv To 66 Kv Considering Sagging Clearance, Muhammad Lazuardi Azzura, Anne Zulfia Syahrial, Julius Purnama Eka Kartika

Journal of Materials Exploration and Findings

Efforts to increase the capacity of transmission networks are often undertaken by uprating the operating voltage of existing lines rather than building entirely new infrastructure. Such uprating typically involves the replacement of tower insulator stringsets to withstand higher voltages, while also ensuring that mechanical performance remains adequate. This paper presents an analysis of uprating the Parakan–Sunyaragi transmission line from 33 kV to 66 kV, with particular emphasis on conductor sagging and the resulting clearance from the ground. The methodology employed includes calculations based on catenary equations, analysis of conductor tensile forces, and a comparative evaluation of two widely used insulator …

Lafe0.925ti0.075o3 Perovskite Coated With Ethyl Cellulose: A High-Stability, Low-Hysteresis Platform For Advanced Humidity Sensing, Akhmad Futukhillah Fataba Alaih, Djoko Triyono, Rifqi Almusawi Rafsanjani

Makara Journal of Science

Humidity sensors are pivotal in numerous sectors, such as environmental monitoring, industrial automation, and health-care. This study presents the fabrication and detailed evaluation of an advanced humidity sensor using ethyl cellulose (EC)-coated LaFe_0.925Ti_0.075O₃ (LFTO) perovskite nanoparticles synthesized via the sol-gel method. The LFTO nanopar-ticles exhibited a mesoporous structure with an enhanced surface area, which significantly improved their moisture adsorption capabilities. The innovative application of EC coating addresses critical substrate adhesion issues, enhancing mechanical stability without compromising sensor sensitivity. Comprehensive performance evaluations revealed minimal hysteresis (

Post-Calcium Treatment Evolution Of Alumina (Al2o3) Inclusions Morphology, Naziru I. Fuseini, Ronald J. O'Malley, Todd P. Sander, Jeffrey D. Smith, Haiming Wen, Laura N. Bartlett

Materials Science and Engineering Faculty Research & Creative Works

The post-calcium morphological evolution of Al₂O₃ inclusions formed under high-oxygen supersaturation (~1000 ppm) was investigated through time-resolved sampling and quenching of aluminum-killed, calcium-treated steel. SEM-EDS analysis revealed the formation of angular two-phase CaO·Al₂O₃–CaS inclusions within 1 minute, gradually transforming into spherical liquid 12CaO·7Al₂O₃ and CaO·Al₂O₃ with a thin CaS layer around it. The 3D morphology of the CaS phase of the complex CaO·Al₂O₃–CaS inclusions observed at 1 minute appeared as a cone-cap attached to the partially modified CaO·Al₂O₃. This …

Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …

Microwave-Assisted Reduction Of Critical Metal Oxides From E-Waste Mixture, Kurundu Shavinka Jayasekera

Graduate Theses, Dissertations, and Problem Reports (ETD)

The efficient recovery of critical metals such as tantalum (Ta), manganese (Mn), gallium (Ga), and indium (In) from electronic waste (e-waste) is essential for resource sustainability and environmental protection. This research uses microwave-assisted treatment to investigate the carbothermal reduction of these four specific metals from their oxides in a simulated e-waste mixture, with carbon black serving as both a microwave coupling and reduction agent. Microwave processing is used specifically because it offers a rapid and energy-efficient alternative to conventional thermal methods, with the benefits of intrinsic heating and selective heating of materials. The first experiments centered on understanding the effects …

Pulsing-Induced Healing Of A Surface Crack Of A Nickel-Based Alloy, Liwei Wang, Mingming Quan, Zhen Tan, Ming Liu, Dianlong Wang, Xiao Yang, Ying Liu, Yaning Mao, Zhimin Liang, Fuqian Yang

Chemical and Materials Engineering Faculty Publications

In this work, we demonstrate the feasibility of applying electric pulses to heal surface cracks on nickel-based alloy GH4169 under compressive load. There exists an incubation time for the onset of the healing of a crack, which is associated with local temperature at the crack tip. The crack size decreases with increasing the pulsing time at a constant healing rate prior to complete healing of the crack. Increasing compressive load accelerates the healing process. The electric pulsing leads to the formation of an influential zone surrounding the crack with the finest grain sizes in the healed crack and the coarsest …

Mechanisms Of Dendritic Shorting In Lithium Metal Batteries With Li7la3zr2o12 Solid Electrolytes, Lukas Karapin-Springorum

Pomona Senior Theses

Energy storage will play a crucial role in efforts to mitigate the effects of climate change caused by greenhouse gas emissions from human activity. Lithium metal batteries using solid electrolytes like Li₇La₃Zr₂O₁₂ have higher energy density than lithium-ion batteries, which may enable a more rapid and complete electrification of transportation. However, lithium metal batteries suffer from undesirable short-circuiting when metallic lithium deposits connect the two electrodes. It has been debated whether these lithium dendrites generally grow directionally from the anode or are generated by the reduction of lithium ions inside the solid electrolyte, …

Calculation Of Elastic Constants Of Bulk Metallic Glasses From Indentation Tests, Zhitong Xu, Ming Liu, Fuqian Yang

Chemical and Materials Engineering Faculty Publications

One of the challenges in the applications of instrumented indentation is to simultaneously measure elastic modulus and Poisson’s ratio of homogeneous, isotropic materials. This work proposes empirical equations for simultaneous calculation of elastic modulus and Poisson’s ratio of bulk metallic glasses (BMGs) from the ratio of the short diagonal length to the long diagonal length and the area of the Knoop imprint. The parameters pre- sented in the empirical equations are determined first by Knoop microhardness tests of 24 BMGs, whose elastic moduli and Poisson’s ratios are measured by resonant ultrasound spectroscopy. These empirical equations are further validated by the …

Atomistic Simulation Studies Of Thin Film Growth And Plastic Deformation In Metals And Metal/Ceramic Nanostructures, Reza Namakian

LSU Doctoral Dissertations

Despite the significant improvements in manufacturing and synthesis processes of metals and ceramics in the past decades, there are still areas in which the procedure is still frequently more of an art or skill rather than a science. Therefore, systematic and combined experimental and computational studies are required to facilitate the development of techniques that offer thorough understanding of the events taking place during manufacturing and synthesis processes. With regard to these issues, it is paramount to address microscale characterizations and atomic scale understanding of the events during fabrication processes. One of the focuses of this study is unraveling fundamental …

Cascaded Sapphire Fiber Bragg Gratings Inscribed By Femtosecond Laser For Molten Steel Studies, Dinesh Reddy Alla, Deva Prasad Neelakandan, Farhan Mumtaz, Rex E. Gerald, Laura Bartlett, Ronald J. O'Malley, Jeffrey D. Smith, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

This research reports a distributed fiber optic high-temperature sensing system tailored for applications in the steel industry and various other sectors. Recent advancements in optical sensor technology have led to the exploration of sapphire crystal fibers as a solution for sensing in harsh environments. Utilizing a femtosecond (fs) laser, cascaded fiber Bragg gratings (FBGs) were meticulously fabricated within a multimode sapphire optical fiber. These FBGs endowed the system with distributed sensing capabilities and underwent rigorous testing under extreme temperatures, reaching up to 1,800 °C. The study delves into the investigation of the FBG reflection spectrum, facilitated by the development of …

Review: Factors Affecting Composite Laminates Against Lightning Strikes, Aaryan Manoj Nair

Publications and Research

Lightning strike protection (LSP) have recently been a newly developing field particularly with the emergence of graphene thin film integration into carbon fiber composite structures. This technology has a widespread application in airplanes, wind turbines, and other instruments which are susceptible to frequent lightning strikes. Electrical discharge of the instrument in a safe manner is vital for the safety of the passengers (in the case of flights) as well as the integrity of the aircraft structures because of their specific mechanical and structural properties, which are essential for their functioning. The purpose of the study is to fabricate graphene thin …

Interactions Between Dry Vibratable Tundish Linings And Steel Melts, Tyler M. Richards, Ronald J. O'Malley, Jeffrey D. Smith, Todd P. Sander

Materials Science and Engineering Faculty Research & Creative Works

Interactions between two tundish working linings and molten steel were investigated using industrial samples and laboratory testing. Periclase-based dry vibe linings from two production facilities were sampled and examined after casting: one containing 30 wt.% olivine and one without olivine. Cathodoluminescence imaging, secondary electron microscopy, energydispersive spectroscopy and x-ray diffraction analysis were performed to characterize the interactions. An experiment was developed to replicate the conditions found in a production tundish on the laboratory scale. Results comparing interactions observed in laboratory lining tests and commercial lining samples for the two lining materials are presented and discussed.

Erosion Resistance Of Tungsten-Carbide Coatings For Steel Pipes In Fluid Catalytic Cracking Units, Davis Vannasing, Jennifer Hulfachor

Materials Engineering

In petroleum processing, the flow of catalyst readily leads to erosion of piping in a fluid catalytic cracking unit. Advances in coating materials and processes necessitate a re-evaluation of current protection methods. Commercially available tungsten-carbide (WC) claddings and nanostructured WC-W CVD coatings were investigated as potential alternative erosion-resistant coatings. Erosion tests by solid particle impingement were conducted on 2 variations of claddings and 1 variation of WC-W coatings following ASTM standard G76. A36 steel coupons were used as reference samples. For statistical validation, 2-3 replications of the tests were performed for the claddings and WC-W coating. Testing was conducted using …

Investigation Of Copper Infiltration Alloys For Use In Metal Matrix Composite Drill Bits, Samuel J. Stueland, Timothy P. Markiewicz

Materials Engineering

A newly developed copper-based alloy, P98-X1 was tested for compressive strength to predict qualitative performance compared to MF53, F-Bronze, CuNiSn, and CuMnNi for use as the infiltration alloy in metal matrix composite (MMC) drill bits. Ingots of each alloy were cast using an arc furnace and cut into compression testing samples using wire electrical discharge machining (EDM). The alloys were selected for testing based on solid solution strengthening coefficient and melting point. Five of each alloy were compression tested to determine yield strength of the infiltration alloy. Yield strength was determined using a 0.002mm displacement offset from the linear elastic …

Metallic Systems At The Nano And Micro Scale: Bimetallic Nanoparticles As Catalysts And Mcraly Bond Coats In Thermal Barrier Coatings, Kenneth Kane

Theses and Dissertations

The dissertation is split into two parts. The first part will be focused on changes in material properties found at the nanoscale, as miscibility and electronic structure can change significantly with size. The formation of classically-immiscible bimetallic nanoparticles (BNPs) becomes favorable at the nanoscale and novel catalytic properties can emerge from the bimetallic alloying. The formation of alloyed and non-alloyed BNPs is achieved through pulse laser ablation (PLA) and a significant increase in catalytic activity is observed for both. Recently discovered, the increased activity in the non-alloyed BNPs, deemed multicomponent photocatalysis, is examined and the proposed mechanism discussed. The second …

Material Properties Design Using Simulations And Experiments For Powder Injection Molding Of Lead Zirconate Titanate (Pzt)., Bhushan Pramod Bandiwadekar

Electronic Theses and Dissertations

Powder injection molding (PIM) process simulations can be performed to minimize the number of injection molding experiments by estimating material properties necessary for PIM simulations. In current work, lead zirconate titanate (PZT) powder-polymer binder feedstock was compounded for 45 vol. % and 52 vol. % solids loading. PIM experiments on designed micro-pillar array geometry were performed using 52 vol. % PZT. Using PIM experiments results as basis, PIM simulations were performed on designed micro-pillar array geometries to understand the effectiveness of PIM simulations with the use of estimated feedstock properties in predicting molding behavior that have micro-features. Additionally, PIM simulations …

Controlling Properties Of Agglomerates For Chemical Processes, Joseph A. Halt

Dissertations, Master's Theses and Master's Reports

Iron ore pellets are hard spheres made from powdered ore and binders. Pellets are used to make iron, mainly in blast furnaces. Around the time that the pelletizing process was developed, starch was proposed as a binder because it’s viscous, adheres well to iron oxides, does not contaminate pellets and is relatively cheap. In practice, however, starch leads to weak pellets with rough surfaces – these increase the amount of dust generated within process equipment and during pellet shipping and handling. Thus, even though the usual binder (bentonite clay) contaminates pellets, pelletizers prefer it to starch or other organics.

This …

Wetting And Interfacial Microstructure Of Porous Si3n4/Si3n4 Joint After Silver Metallization, Yanli Zhuang, Tiesong Lin, Shengjin Wang, Peng He, Dusan P. Sekulic, Dechang Jia, Hongmei Wei

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Review On Joining Of Advanced Materials And Dissimilar Materials In Harbin Institute Of Technology, Jun Qu, Yongping Lei, Peng He, Yunlong Chang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Thermoelectric Half-Heuslers: Synthesis, Processing, And Performance, Joseph Robert Croteau

Boise State University Theses and Dissertations

Thermoelectric half-Heusler compounds have potential to convert the heat wasted from industrial and transportation processes to useful electricity. Among the highest performing half-Heusler compounds are nano-structured bulk materials which have been arc-melted, pulverized into a nano-powder, and sintered by DC-hot press. High performing n- and p-type half-Heusler compounds with nominal composition of Hf_0.25Zr_0.75NiSn_0.99Sb_0.01 and Nb_0.75Ti_0.25FeSb, respectively, have been provided to us in both dense and powder form by our collaborators at the University of Houston. We consolidate these powders by SPS, refine these powders to improve both particle size …

Cermet Development For High Temperature And High Pressure Applications, Beatriz Justus Ferez, Samantha Guthrie, Brian J. Jaques (Mentor), Darryl P. Butt (Mentor)

Idaho Conference on Undergraduate Research

Many traditionally used low cost alloys are easily corroded in steam or supercritical CO₂. An effective solution is to utilize ceramic heat exchangers that are often integrated with metallic components which result in a significant thermal expansion mismatch. The goal of this project is to develop a sealing method to create a hermetic joint between the ceramic and metal alloy. Proposed is a seal ring containing a cermet powder with a coefficient of thermal expansion (CTE) higher than the ceramic and metal to produce a high temperature compressive seal. Cermets of Ag and MgO have been selected to …

Characterization Of Aluminum-Boron Carbide Particulate Metal Matrix Composites, Eric Blank

Materials Engineering

The analysis of die-cast 380 aluminum-boron carbide particulate metal matrix composites (MMC) was performed in order to see if the samples had the required tensile strength of 300 MPa. 10wt% B4C die-cast samples were produced and tested. Half were heat treated to the T6 condition and the others were left as cast. Using ASTM standard B 557M it was found that the average tensile strength for the as-cast samples was 130 MPa and the heat treated samples had a tensile strength of 93 MPa. These values were both lower than expected. The heat treated samples were not expected to have …

Thickness Effects On The Ac And Dc Electrical Behavior Of Rf-Sputtered Batio3 Nano-Capacitors With Pt And Ni Electrodes, James N. Reck, Matthew O'Keefe, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

Nanoscale BaTiO₃ capacitors were deposited on Si wafers at dielectric thicknesses of approximately 25, 50, 100, and 200 nm using RF-magnetron sputtering with either 25 nm thick Ni or Pt electrodes. Multiple DC and AC tests were conducted on these devices to determine the effects of BaTiO₃ thickness on the measured dielectric behaviors. All films were observed to have non-linear responses for resistance, permittivity, and loss with respect to dielectric thickness. The permittivity was found to follow a standard dead layer model behavior with measured values ranging from approximately 350 to 1700 for Ni electrodes and approximately 100 …

2nd Annual Undergraduate Research Conference Abstract Book, University Of Missouri--Rolla

Undergraduate Research Conference at Missouri S&T

No abstract provided.

Modeling The Dielectric Response And Relaxation Spectra Of Relaxor Ferroelectrics, Huh Tswen Lin, David C. Van Aken, Wayne Huebner

Materials Science and Engineering Faculty Research & Creative Works

A multi-Debye relaxation model that is based upon the Boltzmann superposition principle has been used to determine the frequency-dispersion behavior of Pb (Mg_1/3-Nb_2/3)O₃ (PMN) and Pb_0.88La_0.08 (Zr_0.65Ti_0.35) O₃ (PLZT 8/65/35) relaxor ferroelectrics. For PMN, relaxation times on the order of seconds contribute to the dispersive character of the dielectric properties. A defect-relaxation mechanism that involves Mg cation hopping in a structure that is composed of interpenetrating 〈111〉 chains of ordered Pb (Mg_1/2Nb_1/2) O₃ is proposed for PMN. Motion of the Mg cations …

Effects Of Oxygen Content Of Admitted Gases In Sulfide Flotation, Brian J. Boyle

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Methods Of Studying The Effects Of Frothers, Frank L. Bazzanella

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Studies In Modulation Of Interfacial Reactions For Certain Sulphide Minerals, Robert Owen Beyaert

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.

Habit Modification Of Naclo3 With Nai, William A. Coghlan

Bachelors Theses and Reports, 1928 - 1970

No abstract provided.