Ceramic Materials Commons^™

Improving The Concrete Compressive And Flexural Strength With A Low Fraction Addition Of Carboxylated Nitro-Oxidized Cellulose Nanofibrils From Banana Rachis, Ngesa Ezekiel Mushi, Emmanuel Kagya

Tanzania Journal of Science

Conventionally, concrete strength depends on the bonding interface, especially in hydrated products such as calcium silicate hydrate (CSH). As a result, concrete is sensitive to tensile load. With its unique properties, a low fraction of carboxylated nitro-oxidized cellulose nanofibrils (NOCNF) from the banana rachis is employed to improve the mechanical performance of the concrete nanostructurally. Compressive and flexural strength using the NOCNF content at 0, 0.05, and 0.1 wt.%, cured for 7 and 28 days, were evaluated. Notably, the compressive strength increased by 16 % and the flexural strength by 13 % at 0.1 wt.% NOCNF compared to plain concrete …

Lafe0.925ti0.075o3 Perovskite Coated With Ethyl Cellulose: A High-Stability, Low-Hysteresis Platform For Advanced Humidity Sensing, Akhmad Futukhillah Fataba Alaih, Djoko Triyono, Rifqi Almusawi Rafsanjani

Makara Journal of Science

Humidity sensors are pivotal in numerous sectors, such as environmental monitoring, industrial automation, and health-care. This study presents the fabrication and detailed evaluation of an advanced humidity sensor using ethyl cellulose (EC)-coated LaFe_0.925Ti_0.075O₃ (LFTO) perovskite nanoparticles synthesized via the sol-gel method. The LFTO nanopar-ticles exhibited a mesoporous structure with an enhanced surface area, which significantly improved their moisture adsorption capabilities. The innovative application of EC coating addresses critical substrate adhesion issues, enhancing mechanical stability without compromising sensor sensitivity. Comprehensive performance evaluations revealed minimal hysteresis (

Fly Ash Proppant Developed For Hydraulic Fracturing, Raz Rzgar Haydar

Theses and Dissertations

Proppants are critical components in hydraulic fracturing, used to maintain fracture conductivity and enhance reservoir stimulation. In high-pressure and harsh reservoir environments, the use of high-strength proppants is essential to ensure well performance. Conventional proppants, being sand, ceramic, and sintered bauxite can be expensive, and their use often requires costly fracture fluids. This study investigates the possibility of utalizing fly ash geopolymers as a sustainable alternative that is also cost-effective for proppants manufacturing. Fly ash, a by-product from the combustion of coal and other materials, was explored as a base material for proppants, utilizing an alkaline solution as an activator …

Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …

In-Situ Investigations Of Calcium-Magnesium-Aluminosilicates (Cmas) Infiltration Effects On Thermal Barrier Coatings Under Extreme Environments Replicating Jet Engines, Zachary Stein

Doctoral Dissertations and Master's Theses

Calcium-magnesium-aluminosilicate (CMAS) particulates, such as sand or volcanic ash, are ingested by gas turbine jet engines during operation. When operating within high abundance regions, these particulates negatively interact and degrade the high temperature thermal barrier coatings (TBC) protecting underlying superalloy turbine blades vital to engine operation. These CMAS particulates melt within the engine and infiltrate into the ceramic coatings. In electron-beam physical vapor deposited (EB-PVD) TBCs, the CMAS within the intercolumnar gaps stiffens the coatings and causes thermomechanical induced high stress concentrations, risking crack formation. While molten, the CMAS thermochemically alters and destabilizes the coating, also risking coating failure. Premature, …

Extraction Of Aluminum From Lunar Regolith Through Molten Salt Electrolysis, Jacob N. Ortega, Todd P. Sander, Jeffrey D. Smith, Fateme Rezaei, David J. Bayless, William Schonberg, Daniel S. Stutts, Frank D. Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents the methodology, development, and results of an end-to-end regolith-to-metal concept for producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method. Using electrolytic reduction, aluminum oxide (i.e., alumina) can be reduced into aluminum and oxygen via electrolysis in a molten salt bath. A steady supply of hydrogen chloride could allow this in-situ resource utilization (ISRU) method to supply several necessary materials consumed in the electrolytic reduction step of the process to produce bulk aluminum metal, oxygen, water, and silica from anorthite abundant in lunar highland regions. In this …

Tensile Creep Of A Hybrid Polymer-Matrix/Ceramic-Matrix Composite At Elevated Temperature, Waleed S. Alshehri

Theses and Dissertations

Advanced aerospace systems require structural materials that can perform reliably in high-temperature environments for long durations. The performance of standard polymer matrix composites (PMCs) in these conditions is often limited by their susceptibility to time-dependent deformation, such as creep. The objective of this research is to characterize the high-temperature creep behavior of a novel unitized material system comprising a polymer matrix composite (PMC) and a ceramic matrix composite (CMC) co-cured together. The PMC part consists of the polyimide matrix reinforced with laminated carbon fibers woven in an eight harness satin weave (8HSW). The CMC part consists of a zirconia-based ceramic …

Mno2 Nanoscale Interface Modification, Alexander C. Skoppe

Doctoral Dissertations and Master's Theses

Interface modification of carbon fibers has been shown to improve the mechanical performance of composites. In addition, interface modification of carbon fiber composites can impart multifunctionality into the resulting composite. This work will explore ZnO and MnO2 as interface modifications for use on carbon fibers. When exposed to high temperatures, carbon fibers undergo fiber degradation, leading to the need for low-temperature hydrothermal processes. This work will develop and characterize a nanoscale ZnO and MnO2 interface modification for use on carbon fibers. These nanomodifications will be developed with low-temperature processes, minimizing the fiber degradation that the fibers undergo. Fourier transform infrared …

Microwave-Assisted Reduction Of Critical Metal Oxides From E-Waste Mixture, Kurundu Shavinka Jayasekera

Graduate Theses, Dissertations, and Problem Reports (ETD)

The efficient recovery of critical metals such as tantalum (Ta), manganese (Mn), gallium (Ga), and indium (In) from electronic waste (e-waste) is essential for resource sustainability and environmental protection. This research uses microwave-assisted treatment to investigate the carbothermal reduction of these four specific metals from their oxides in a simulated e-waste mixture, with carbon black serving as both a microwave coupling and reduction agent. Microwave processing is used specifically because it offers a rapid and energy-efficient alternative to conventional thermal methods, with the benefits of intrinsic heating and selective heating of materials. The first experiments centered on understanding the effects …

Tension–Compression Fatigue Of A Hybrid Polymer-Matrix/Ceramic-Matrix Composite At Elevated Temperature, Marina B. Ruggles-Wrenn, Joshua Schmidt

Faculty Publications

Fully reversed tension–compression fatigue of a hybrid material comprising polymer matrix composite (PMC) co-cured with a ceramic matrix composite (CMC) was investigated. The PMC portion had a polyimide matrix reinforced with 15 plies of carbon fibers woven in an eight-harness satin weave (8HSW). The CMC portion had three plies of a quartz-fiber 8HSW fabric in a zirconia-based ceramic matrix. The hybrid PMC/CMC was developed for use in aerospace thermal protection systems (TPS). Hence, the experimental setup aimed to simulate the TPS service environment—the CMC side was kept at 329 °C, whereas the PMC side was open to laboratory air. Compression …

Progress Of Lisap-Mse: A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, David Bayless, Daniel Stutts, Daoru Han, Todd P. Sander, Jeffrey Smith, Fateme Rezaei, William Schonberg

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Mechanisms Of Dendritic Shorting In Lithium Metal Batteries With Li7la3zr2o12 Solid Electrolytes, Lukas Karapin-Springorum

Pomona Senior Theses

Energy storage will play a crucial role in efforts to mitigate the effects of climate change caused by greenhouse gas emissions from human activity. Lithium metal batteries using solid electrolytes like Li₇La₃Zr₂O₁₂ have higher energy density than lithium-ion batteries, which may enable a more rapid and complete electrification of transportation. However, lithium metal batteries suffer from undesirable short-circuiting when metallic lithium deposits connect the two electrodes. It has been debated whether these lithium dendrites generally grow directionally from the anode or are generated by the reduction of lithium ions inside the solid electrolyte, …

A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daniel Stutts, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Solid-State Electrolytes For Long Duration Molten Sodium Batteries, Ryan C. Hill

Theses and Dissertations--Chemical and Materials Engineering

Rechargeable batteries have become a staple of modern society, driving the development and expansion of portable electronics and electric vehicles. The long lifetime and high energy density provided by batteries have made them excellent candidates for use in the emerging field of long duration, grid-scale energy storage. However, traditional battery chemistries, such as Li-ion, are not an ideal solution for grid-scale storage, due to high-cost raw materials that are often sourced from volatile markets. Sodium-based batteries are a promising alternative for long duration storage, owing to the domestic abundance of raw materials and energy densities that nearly rival that of …

Evaluating The Effects Of Granulated Rubber And Glass Fibers In Polymer Concrete As A Structural Material For Wafer Grinding Machines, Kevin Gabriel Kuehn, Philip Randall Streeter

Materials Engineering

Polymer concrete is a composite material used to replace cast iron and steel in wafer grinding machines for vibration damping. During the grinding and lapping processes of manufacturing silicon wafers, excessive vibrations may cause subsurface damage which requires additional polishing and reduces yield. Nine compositions containing various levels of granulated rubber and glass fibers were manufactured. CRM WRF-10 granulated rubber was examined at 0%, 5%, and 10% and Corning Cem-Fil glass fibers were added at 0%, 0.5%, and 1% by weight. Smooth-On EpoxAcast 690 epoxy resin was held constant at 16% for each composition. Crushed granite aggregate from Martin Marietta, …

Study Of Static And Dynamical Properties Of Complex Antiferroelectrics Materials, Kinnary Yogeshbhai Patel

Graduate Theses and Dissertations

The aim of this dissertation is the investigation of the static and dynamical properties of the complex antiferroelectric materials using Effective Hamiltonian method and First principles calculations. In chapter 3, a novel elemental interatomic coupling in perovskite materials which bilinearly couples the antiferroelectric displacements of cations with the rotations of the oxygen octahedra. This new coupling explains a very complex crystal structure of prototypical antiferroelectric PbZrO3. My explanation provides a unified description of many other complex antipolar crystal structures in variety of perovskite materials, including the occurrence of incommensurate phases in some of them. In chapter 4, results and analysis …

Research Trend Of Metal Matrix Composites Reinforced With Silica Extracted By Green Route: A Bibliometric Analysis, Rinku Datkhile, Meena Laad, Babaji Ghule

Library Philosophy and Practice (e-journal)

Metal Matrix Composites have acquired an important place in the engineering applications due to their distinctive characteristics such as high specific strength, lower specific gravity, improved material stiffness, better durability, enhanced creep and fatigue strength etc. Worldwide scientists are working on the improvement of mechanical properties of composite materials. The present work attempts to summarise all the research carried out on metal matrix composites reinforced with silica extracted by green route and provides up-to-date research material for researchers who are interested in the field of composites with metal matrices. Scopus databases and software such as Gephi Vos Viewer and Table2Net …

Fatigue Of A Sic/Sic Ceramic Composite With An Ytterbium‐Disilicate Environmental Barrier Coating At Elevated Temperature, Marina B. Ruggles-Wrenn, Thaddeus M. Williams

Faculty Publications

Excerpt: Tension-tension fatigue performance of a SiC/SiC composite with an ytterbium-disilicate environmental barrier coating (EBC) was investigated at 1200°C in air and steam. The composite is reinforced with Hi-Nicalon™ SiC fibers and has a melt-infiltrated matrix processed by chemical vapor infiltration of SiC with subsequent infiltration with SiC particulate slurry and molten silicon. Abtract © American Ceramic Society

Tension-Tension Fatigue Behavior Of Nextel™ 720/Alumina-Mullite Ceramic Composite At 1200°C In Air And In Steam, Sarah A. Witzgall

Theses and Dissertations

Uniaxial tension-tension fatigue performance of an oxide-oxide continuous fiber ceramic composite was studied at 1200°C in laboratory air and in steam. The composite is reinforced with laminated, 0/90 mullite/alumina (NEXTEL™720) fibers woven in an eight-harness satin weave and has a porous alumina/mullite matrix. There is no interphase between the fiber and matrix. The composite relies on the porous matrix for crack deflection and flaw tolerance. Tension-tension fatigue was examined for maximum stresses of 45 – 136 MPa in air and in steam. To assess the effects of the steam environment on fatigue performance, experimental results obtained in air are compared …

Fatigue Behavior Of An Advanced Melt-Infiltrated Sic/Sic Composite With Environmental Barrier Coating At 1200°C In Air And In Steam, Thaddeus M. Williams

Theses and Dissertations

Advanced aerospace applications such as aircraft turbine engine components, hypersonic flight vehicles, and spacecraft reentry thermal protection systems require structural materials that have superior long-term mechanical properties under high temperature, high pressure, and varying environmental factors, such as moisture. Because of their low density, high strength and fracture toughness at high temperatures SiC fiber-reinforced SiC matrix composites are being evaluated for aircraft engine hot-section components. In these applications the composites will be subjected to various types of mechanical loadings at elevated temperatures in oxidizing environments. Because their constituents are intrinsically oxidation-prone, the most significant problem hindering SiC/SiC composites is oxidation …

Ballistic Evaluation Of Carbon Nanotube Sheet Material In Multifunctional Applications, Casey M. Keilbarth

Theses and Dissertations

Significant development of carbon nanotubes has occurred since they were first studied in the 1990's. Attempts to capture the phenomenal molecular properties in practical applications are gaining ground as new methods of producing CNTs have been developed. This thesis sought to determine if the addition of commercially produced CNT sheets to thin carbon fiber panels improved the ballistic properties of the panel. The difference between 0 and 4 CNT sheets was studied. The hypothesis was that inte- grating CNT sheets into the laminate would increase the projectile energy absorbed by the panel and reduce the damage to the panel incurred …

Measuring Characteristic Shrinkage Variability Due To Metal Loading Effects In Low Temperature Co-Fired Ceramic Using Image Processing, John Ezekiel Zumbro

Graduate Theses and Dissertations

Low temperature co-fired ceramic (LTCC) has many benefits when it comes to electronic packaging due to the low dielectric loss, reliability in extreme environments, and high breakdown voltage. Though the ceramic has a lot of benefits it is not widely used due to the high cost and complexities associated with manufacturing. One of these issues with manufacturing is compensating for the shrinkage of the ceramic, this is accomplished by using an expansion factor, creating the “green” or manufactured design. This expansion factor is approximated through knowledge of the ceramic factors such as the metal loading, layers of ceramic tape, firing …

Creep Of Hafnium Diboride -20 Vol% Silicon Carbide At 1500°C In Air, Glen E. Pry

Theses and Dissertations

Refractory metal borides, commonly referred to as Ultra High Temperature Ceramics (UHTCs), exhibit a number of unique properties, such as extremely high melting temperature and hardness, chemical stability, high electrical and thermal conductivity and corrosion resistance. It has been demonstrated that the addition of SiC improves the oxidation resistance of ZrB2- and HfB2-based UHTCs above 1200°C by modifying the composition of the oxide scale. Addition of SiC retards the oxidation rate of ZrB2 and HfB2 by forming a protective layer of borosilicate glass. Creep deformation is one of the critical criterion for structural application of ceramics at elevated temperatures. Compression …

High Pressure Behavior Of Mullite-Type Oxides: Phase Transitions, Amorphization, Negative Linear Compressibility And Microstructural Implications, Patricia Kalita

UNLV Theses, Dissertations, Professional Papers, and Capstones

Even though mullite occurs rarely in nature, it is perhaps one of the most important phases in both traditional and advanced ceramics. Existing and emerging applications of mullite and mullite-type materials include: high-temperature composites, aerospace materials, ballistic shielding for military applications and even non-linear optical materials. There are many uncertainties regarding the basic physical properties of mullite-type materials, particularly in terms of their high-pressure structural stability and mechanical behavior that are important to address for emerging applications of mullites as engineering materials. This work is the first reported comprehensive investigation of the high –pressure structural behavior of several different mullites …

Experimental Investigation Of Mechanical Behavior Of An Oxide/Oxide Ceramic Composite In Interlaminar Shear And Under Combined Tension-Torsion Loading, Skyler R. Hilburn

Theses and Dissertations

Creep behavior in interlaminar shear of an oxide-oxide ceramic composite, Nextel 720™/aluminosilicate (N720/AS), was investigated at 1100°C in laboratory air and in steam. The interlaminar shear strength (ILSS) was determined as 7.65 MPa. The creep behavior was examined for interlaminar shear stresses in the 2-6 MPa range. Primary and secondary creep regimes were observed in all tests conducted in air and in steam. Tertiary creep was noted in the tests performed at 6 MPa. Larger creep strains and higher creep strain rates were produced in steam. Surprisingly, the presence of steam had a beneficial effect on creep lifetimes. It appears …

Finite Element Analysis Of The Contact Deformation Of Piezoelectric Materials, Ming Liu

Theses and Dissertations--Chemical and Materials Engineering

Piezoelectric materials in the forms of both bulk and thin-film have been widely used as actuators and sensors due to their electromechanical coupling. The characterization of piezoelectric materials plays an important role in determining device performance and reliability. Instrumented indentation is a promising method for probing mechanical as well as electrical properties of piezoelectric materials.

The use of instrumented indentation to characterize the properties of piezoelectric materials requires analytical relations. Finite element methods are used to analyze the indentation of piezoelectric materials under different mechanical and electrical boundary conditions.

For indentation of a piezoelectric half space, a three-dimensional finite element …

Studies Of Dynamic Crack Propagation And Crack Branching With Peridynamics, Youn Doh Ha, Florin Bobaru

Department of Engineering Mechanics: Faculty Publications

In this paper we discuss the peridynamic analysis of dynamic crack branching in brittle materials and show results of convergence studies under uniform grid refinement (m-convergence) and under decreasing the peridynamic horizon (δ-convergence). Comparisons with experimentally obtained values are made for the crack-tip propagation speed with three different peridynamic horizons.We also analyze the influence of the particular shape of themicro-modulus function and of different materials (Duran 50 glass and soda-lime glass) on the crack propagation behavior. We show that the peridynamic solution for this problem captures all the main features, observed experimentally, of dynamic crack propagation and branching, as well …

Effects Of Environment On Creep Behavior Of Two Oxide-Oxide Ceramic Matrix Composites At 1200°C, Pavlos Koutsoukos

Theses and Dissertations

Previous studies by the advisor and graduate students examined creep behavior of the Nextel720/Alumina CMC in air and in 100% steam environments at 1200 and 1330°C. Results showed that while this oxide/oxide system exhibits an exceptionally high fatigue limit at 1200°C it also experiences substantial strain accumulation under sustained loading conditions. Furthermore, these earlier investigations revealed a significant degrading effect of 100% steam environment on material performance under both static and cyclic loadings. The present effort will investigate creep rupture behavior of Nextel720/Alumina composite in the inert gas environment. In addition, creep rupture behavior of Nextel720/Aluminosilicate CMC will be investigated …

Effects Of Frequency And Environment On Fatigue Behavior Of An Oxide-Oxide Ceramic Matrix Composite At 1200°C, Griffin Hetrick

Theses and Dissertations

Advances in aeronautical engineering in the 21st century depend upon materials that can perform well in extreme environments such as high temperatures and oxidizing conditions. Nextel™720/Alumina (N720/A) is an oxide/oxide ceramic matrix composite with a porous alumina matrix that has been identified as a candidate material for such applications. This research investigated the effects of frequency on fatigue response of N720/A at 1200°C in both air and steam environment. Prior investigation of this material by Eber [8] in 2005 studied fatigue behavior at 1200°C in air and in steam environments at the frequency of 1.0 Hz. The current research focused …

Effect Of Environment On Creep Behavior Of An Oxide/Oxide Cfcc With ±45° Fiber Orientation, Gregory T. Siegert

Theses and Dissertations

Aerospace applications require materials capable of maintaining superior mechanical properties while operating at high temperatures and oxidizing environments. Nextel™ 720/A (N720/A), an oxide/oxide ceramic matrix composite (CMC) with a porous alumina matrix was developed specifically to provide improved long-term properties and performance at 1200°C. This research evaluated the creep behavior of N720/A with a ±45° fiber orientation at 1200°C in: laboratory air, steam, and argon environments. Creep-rupture tests at the creep stress levels of: 45, 40, 35, and 15 MPa were conducted in each environment.
The ultimate tensile strength of N720/A with ±45° fiber orientation was 55 MPa, the elastic …