Ceramic Materials Commons^™

Extraction Of Aluminum From Lunar Regolith Through Molten Salt Electrolysis, Jacob N. Ortega, Todd P. Sander, Jeffrey D. Smith, Fateme Rezaei, David J. Bayless, William Schonberg, Daniel S. Stutts, Frank D. Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents the methodology, development, and results of an end-to-end regolith-to-metal concept for producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method. Using electrolytic reduction, aluminum oxide (i.e., alumina) can be reduced into aluminum and oxygen via electrolysis in a molten salt bath. A steady supply of hydrogen chloride could allow this in-situ resource utilization (ISRU) method to supply several necessary materials consumed in the electrolytic reduction step of the process to produce bulk aluminum metal, oxygen, water, and silica from anorthite abundant in lunar highland regions. In this …

Characterization Of Aluminum-Boron Carbide Particulate Metal Matrix Composites, Eric Blank

Materials Engineering

The analysis of die-cast 380 aluminum-boron carbide particulate metal matrix composites (MMC) was performed in order to see if the samples had the required tensile strength of 300 MPa. 10wt% B4C die-cast samples were produced and tested. Half were heat treated to the T6 condition and the others were left as cast. Using ASTM standard B 557M it was found that the average tensile strength for the as-cast samples was 130 MPa and the heat treated samples had a tensile strength of 93 MPa. These values were both lower than expected. The heat treated samples were not expected to have …

The Construction And Operation Of A Universal Specimen Mount With Protective Lead Shield For The Purpose Of Determining Pole Figures Using The Schulz-Decker Transmission Technique, Richard L. Fausner

Bachelors Theses and Reports, 1928 - 1970

It was the purpose of this study to construct a universal mount, to construct a protective lead shield, to operate the instrument, and to provide a pole figure using the transmission method of Schulz and Decker. There are at present several lengthy x-ray methods of determining the grain orientation of metals. These methods are mainly photographic. In order to provide a rapid means of obtaining the necessary information concerning the grain orientation of a metal, a universal mount was constructed.

The Effect Of Germanium On The Current Efficiency In The Electrolysis Of Pure Zinc Sulfate Solution, Keith R. Bock

Bachelors Theses and Reports, 1928 - 1970

It has long been recognized that electrolytic zinc cells are extremely sensitive to impurities. In fact, cer­tain impurities present in amounts as low as 0.1 mg/1 cause a serious loss of current efficiency. Also, the presence of several impurities in the electrolyte may accelerate the detrimental effect of each impurity.

Recrystallization Of High Purity Aluminum, Virgil H. Griswold Jr.

Bachelors Theses and Reports, 1928 - 1970

If a metal is first cold-worked and then heated to a sufficient temperature for an adequate length of time, the hardening properties due to cold-working disappear, and the metal will return more or less to its original state. Upon examination of the microstructure, we find that new grains have replaced the old grains through what is called recrystallization. The final size of the recrystallized grains depends upon three important variables--the degree of cold-work or deforma­tion, annealing temperature, and annealing time.

The Effect Of Manganese On The Age Hardening Of Aluminum-Copper Alloys, Keith P. Burgess

Bachelors Theses and Reports, 1928 - 1970

It is known that age-hardening occurs in alloys of the solid solution type containing a hardening constituent, of a metal or metallic compound which is more soluble in the solvent phase at higher tempertures than at lower temperatures.

The Metallography Of Aluminum Casting Alloys, Donald D. Goehler

Bachelors Theses and Reports, 1928 - 1970

The purpose of this thesis is to supply the Montana School of Mines with an up to date source of information concerning the metallography of aluminum casting alloys. This thesis is designed as a continuing project. Ultimately, it is hoped that a catalog containing all the typical structures of aluminum casting alloys will develop.

The Age-Hardening Of Aluminum With Mgzn2, Sidney E. Worthen

Bachelors Theses and Reports, 1928 - 1970

The purpose of this thesis is to investigate the age-hardening of aluminum with magnesium and zinc in such proportions as to conform to the compound MgZn₂.

Because of a lack of time and proper equipment, the only property investigated was the hardness as indicated by the Rockwell Superficial Hardness Tester.

The Age Hardening Of Silver With Copper-Silicide, Joseph Edward Shaw

Bachelors Theses and Reports, 1928 - 1970

The successful application of the phenomenon of pre­cipitation hardening to aluminum and copper has indicated the possibility of hardening all metals in the same way. The phenomenon of age hardening was discoveredin 1911, and since that time much research has been car­ried on in all parts of the world on various alloy sys­tems.

Structure Of Eutectics, Dilip K. Das

Bachelors Theses and Reports, 1928 - 1970

The present paper is a result of work done on the study of structures of eutectics of a certain eutectic-forming binary systems. In this research work no systems with intermetallic compounds have been studied.

The Electroplating Of Cadmium From Sulfate Solutions, Lewis S. Prater

Bachelors Theses and Reports, 1928 - 1970

It has been proven that cadmium forms a very satisfactory plate on steel, which has to withstand severe corrosion, especially the corrosion of sea water and spray. The metal is now successfully plated electrolytically from cyanide solutions, but wherever work is carried on with cyanide, there is great danger of poisoning to the workers.

The Electrolytic Deposition Of Chromium Upon Aluminum, E. Fults, L. D. Voerge

Bachelors Theses and Reports, 1928 - 1970

The purpose or this investigation is primarily to determine the best conditions for plating chromium on aluminum. The work was carried out with the hope of obtaining coherent deposits, and of determin­ing the conditions under which such deposits may be duplicated.