Ceramic Materials Commons^™

Lafe0.925ti0.075o3 Perovskite Coated With Ethyl Cellulose: A High-Stability, Low-Hysteresis Platform For Advanced Humidity Sensing, Akhmad Futukhillah Fataba Alaih, Djoko Triyono, Rifqi Almusawi Rafsanjani

Makara Journal of Science

Humidity sensors are pivotal in numerous sectors, such as environmental monitoring, industrial automation, and health-care. This study presents the fabrication and detailed evaluation of an advanced humidity sensor using ethyl cellulose (EC)-coated LaFe_0.925Ti_0.075O₃ (LFTO) perovskite nanoparticles synthesized via the sol-gel method. The LFTO nanopar-ticles exhibited a mesoporous structure with an enhanced surface area, which significantly improved their moisture adsorption capabilities. The innovative application of EC coating addresses critical substrate adhesion issues, enhancing mechanical stability without compromising sensor sensitivity. Comprehensive performance evaluations revealed minimal hysteresis (

Antibacterial Activity Of Zno/Geopolymer Composite Granules And Their Potential Application In Water Treatment, Ziyan Tirta Maulitia, Putri Nur Angelina, Pipit Erlita Sari, Sri Sugiarti, Irma Isnafia Arief, Zaenal Abidin

Makara Journal of Science

Water pollution has become a major global concern owing to its complexity and widespread impact. Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli) are the most common bacterial contaminants in water sources, which pose significant threats to public health. To mitigate water contamination by these pathogenic microorganisms, developing and implementing effective water treatment technologies are essential. A promising approach involves using antibacterial water filtration systems. Herein, zinc oxide (ZnO) nanoparticles were synthesized via hydrothermal and precipitation methods as antibacterial agents for water treatment. These preparation methods required considerably low synthesis time. A capping agent was …

Photoexcited Charge Carrier Dynamics And Electronic Properties Of Two-Dimensional Mxene, Nb2ctx, Andrew M. Fitzgerald, Emily Sutherland, Tarek A. Elmelegy, Mary Qin Hassig, Julia Martin, Erika Colin-Ulloa, Ken Ngo, Ronald L. Grimm, Joshua R. Uzarski, Michel W. Barsoum, N. Aaron Deskins, Lyubov V. Titova, Kateryna Kushnir Friedman

Mechanical Engineering

Two-dimensional, 2D, niobium carbide MXene, Nb2CTx, has attracted attention due to its extraordinarily high photothermal conversion efficiency that has applications ranging from medicine, for tumor ablation, to solar energy conversion. Here, we characterize its electronic properties and investigate the ultrafast dynamics of its photoexcitations with a goal of shedding light onto the origins of its unique properties. Through density functional theory, DFT, calculations, we find that Nb2CTx is metallic, with a small but finite density of states at the Fermi level for all experimentally relevant terminations of Nb2CTx that can be achieved using HF or molten salt etching of the …

Development Of High Kinetic Inductance Superconducting Nanowire Devices On High Permittivity Strontium Titanate Substrates, Jamie Timmons

UNF Graduate Theses and Dissertations

This thesis involves the fabrication and characterization of devices made from two different superconducting materials: yttrium barium copper oxide (YBCO), a high-TC complex oxide, and niobium nitride (NbN), a low-TC transition metal nitride. Both types of devices are fabricated on strontium titanate substrates, which provides a good lattice match to YBCO and also an extremely large permittivity at low temperature. We demonstrate that wet etching of YBCO thin films via bromine can be a viable microfrabriation technique for the material. Using approximately 35 nm thick epitaxially grown YBCO on an STO substrate, we were able to fabricate YBCO “microwires” with …

Material Characterization And Comparison Of Sol-Gel Deposited And Rf Magnetron Deposited Lead Zirconate Titanate Thin Films, Katherine Lynne Miles

Mechanical Engineering ETDs

Lead zirconate titanate (PZT) has been a material of interest for sensor, actuator, and transducer applications in microelectromechanical systems (MEMS). This is due to their favorable piezoelectric, pyroelectric and ferroelectric properties. While various methods are available to deposit PZT thin films, radio frequency (RF) magnetron sputtering was selected to provide high quality PZT films with the added capability of batch processing. These sputter deposited PZT films were characterized to determine their internal film stress, Young’s modulus, composition, and structure. After characterization, the sputtered PZT samples were poled using corona poling and direct poling methods. As a means of comparison, commercially …

The Effects Of Curing Temperature On The Hydration Kinetics Of Plain And Fly Ash Pastes And Compressive Strength Of Corresponding Mortars With And Without Nano-Tio2 Addition., Dan Huang, Mirian Velay-Lizancos, Jan Olek

International Conference on Durability of Concrete Structures

Incorporation of fly ash in cementitious systems containing ordinary portland cement (OPC) increases their long-term strength and durability. However, replacement of cement by fly ash also reduces the heat of hydration of such systems and reduces early-age strength development. The reduced rate of strength development can increase the risk of durability problems, e.g. scaling, in cases when young concrete is exposed to low temperatures and deicing chemicals. This study investigated the potential of nano-titanium dioxide (nano-TiO₂) particles to modify the hydration kinetics of fly ash pastes and compressive strength development of corresponding mortars cured under low (4°C) and …

Synthesis Of Monodisperse Nanoscintillators At High Temperatures For Biomedical Relevant Applications, Eric Zhang

All Dissertations

Luminescent sub-100 nm particulates continuously generate immense research interest in the biomedical field for imaging, theranostics, and optogenetics. Conventionally, upconversion nanoparticles or UV activated semiconductors are studied, however these materials are limited by biological barriers such as the skin which reduces the penetration depth of these excitation sources, tissue's auto- fluorescence, and toxicity. One approach to overcome these challenges is to use nanoscintillators (sub-100 nm materials that can generate visible light using high energy excitation sources such as x-rays) which can generate light locally to the human body. Numerous scintillators have been reported since the discovery of x-rays from the …

Experimental Investigation Of Surface Resistivity Of Yttrium Stabilized Zirconium As A Thin Film, Matthew J. Melfi

Seton Hall University Dissertations and Theses (ETDs)

Solid Oxide Fuel Cells are devices that use electrochemical reactions to convert chemical energy from fuel to electricity. In comparison with coal power plants, a Solid Oxide Fuel Cell, produces a higher electrical conversion efficiency. However, at higher temperatures (1000°C) it creates a lower ionic conductivity, which limit the Solid Oxide Fuel Cells. When lowering the temperature, the ohmic resistance increases. In our research, an Yttrium Stabilized Zirconium layer will be produced from a fine dimple grain structure allowing high flow of oxygen mobility. This mobility increases ionic conductivity and decrease ohmic loss. The goal of our research is first …

Solid State Synthesis And Characterization Of Apatite Based Ceramic Waste Form For The Immobilization Of Radioactive Iodine, Md Imdadul Islam

LSU Doctoral Dissertations

The growing demand for nuclear power in the United States and worldwide is accountable for addressing the major concern of radioactive waste, involving the technical challenges of maintaining the nuclear fuel cycle and immobilizing high-level wastes for safe disposal in geological storage. The appropriate selection of waste forms for spent nuclear fuel such as fission products and radionuclides can be effective means for a feasible and sustainable nuclear fuel cycle. But highly volatile radionuclides such as iodine (129) are of specific concern due to its extraordinary long half-life (15.7 million years). Due to its poor solubility and high volatility at …

Mxenes As Flow Electrodes For Capacitive Deionization Of Wastewater, Naqsh E. Mansoor

Boise State University Theses and Dissertations

The energy-water nexus poses an integrated research challenge, while opening up an opportunity space for the development of energy efficient technologies for water remediation. Capacitive Deionization (CDI) is an upcoming reclamation technology that uses a small applied voltage applied across electrodes to electrophoretically remove dissolved ionic impurities from wastewater streams. Similar to a supercapacitor, the ions are stored in the electric double layer of the electrodes. Reversing the polarity of applied voltage enables recovery of the removed ionic impurities, allowing for recycling and reuse. Simultaneous materials recovery and water reclamation makes CDI energy efficient and resource conservative, with potential to …

Development Of B-Type And Multi-Ion Doped Carbonated Hydroxyapatite Bioceramics, Safarzadeh Marjan

Student Works (2020-2029)

The present research is aimed to investigate the effect of varying the carbonate to phosphate (CO32−/ PO43‒) molar ratios from 0.5 to 5 on the physical and mechanical properties of carbonated hydroxyapatite (CHA) synthesized by a wet chemical method. The sintering was performed under dry carbon dioxide atmosphere at 900 °C to maintain the B-type CHA structure. It was found that increases in CO32−/ PO43‒ ratio was accompanied by an increase in the c/a lattice ratio. The diffraction peaks of the synthesized 0.5-5 CHA powders exhibited a single phase material except for 5CHA which revealed the some minor calcite or …

Nano Fab Lab 63, Brian K. Deemer, Josh Clemons, Nick Brodine, Delaney Fitzsimmons

Mechanical Engineering

Lawrence Livermore National Laboratories (LLNL) has several steps in the production process for ceramic nanofiber tubes that they would like to improve - electrospinning, cutting, rolling, sealing and heat treating. We undertook the challenge to deliver LLNL with a semi-automated process that efficiently integrates the steps of cutting, rolling, and sealing to save time and improve control over end dimensions. In this document, we discuss the technical background of the manufacturing steps currently followed to create nanofiber tubes, identify which steps are incorporated in our prototype and explain how they will interface with one another, define the design requirements, present …

Wetting And Interfacial Microstructure Of Porous Si3n4/Si3n4 Joint After Silver Metallization, Yanli Zhuang, Tiesong Lin, Shengjin Wang, Peng He, Dusan P. Sekulic, Dechang Jia, Hongmei Wei

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Review On Joining Of Advanced Materials And Dissimilar Materials In Harbin Institute Of Technology, Jun Qu, Yongping Lei, Peng He, Yunlong Chang

The 8th International Conference on Physical and Numerical Simulation of Materials Processing

No abstract provided.

Developent Of A Phospholipid Encapsulation Process For Quantum Dots To Be Used In Biologic Applications, Logan Grimes

Master's Theses

The American Cancer Society predicts that 1,665,540 people will be diagnosed with cancer, and 585,720 people will die from cancer in 2014. One of the most common types of cancer in the United States is skin cancer. Melanoma alone is predicted to account for 10,000 of the cancer related deaths in 2014. As a highly mobile and aggressive form of cancer, melanoma is difficult to fight once it has metastasized through the body. Early detection in such varieties of cancer is critical in improving survival rates in afflicted patients. Present methods of detection rely on visual examination of suspicious regions …

Finite Element Analysis Of The Contact Deformation Of Piezoelectric Materials, Ming Liu

Theses and Dissertations--Chemical and Materials Engineering

Piezoelectric materials in the forms of both bulk and thin-film have been widely used as actuators and sensors due to their electromechanical coupling. The characterization of piezoelectric materials plays an important role in determining device performance and reliability. Instrumented indentation is a promising method for probing mechanical as well as electrical properties of piezoelectric materials.

The use of instrumented indentation to characterize the properties of piezoelectric materials requires analytical relations. Finite element methods are used to analyze the indentation of piezoelectric materials under different mechanical and electrical boundary conditions.

For indentation of a piezoelectric half space, a three-dimensional finite element …

Influence Of Magnesium Nitrate On The Corrosion Performance Of Sol-Gel Coated Aa2024-T3 Aluminium Alloy, Rajath Varma, Brendan Duffy, John Cassidy

Articles

Traditional anti-corrosion technology has relied heavily on using reducible metal species, predominantly hexavalent chromium (Cr(VI)), for protecting reactive metal alloys such as aluminium which is extensively used in the aerospace sector. However, the impending changes in the use of Cr(VI) in Europe and the United States have forced aerospace manufacturers to examine alternative materials for protecting aluminium. One of the most promising alternatives being investigated are organosilane based sol-gels containing anticorrosion additives. In this work the anti-corrosion properties of magnesium (II) nitrate (Mg(NO3)2) as a inhibitor was investigated at different concentrations (0.1% - 1.0 wt %) in a methyltriethoxysilane (MTEOS) …

A Simple Sol-Gel Processing For The Development Of High-Temperature Stable Photoactive Anatase Titania, Suresh Pillai, Declan Mccormack, John Colreavy

Articles

No abstract provided.

Preparation Of Magnetic Nanoparticles And Their Assemblies Using A New Fe(Ii) Alkoxide Precursor, Suresh Pillai, Grainne Biddlecombe, Yurii Gun’Ko, John Kelly, J. Michael Coey, Alexis Douvalis

Articles

No abstract provided.