Ceramic Materials Commons^™

Lafe0.925ti0.075o3 Perovskite Coated With Ethyl Cellulose: A High-Stability, Low-Hysteresis Platform For Advanced Humidity Sensing, Akhmad Futukhillah Fataba Alaih, Djoko Triyono, Rifqi Almusawi Rafsanjani

Makara Journal of Science

Humidity sensors are pivotal in numerous sectors, such as environmental monitoring, industrial automation, and health-care. This study presents the fabrication and detailed evaluation of an advanced humidity sensor using ethyl cellulose (EC)-coated LaFe_0.925Ti_0.075O₃ (LFTO) perovskite nanoparticles synthesized via the sol-gel method. The LFTO nanopar-ticles exhibited a mesoporous structure with an enhanced surface area, which significantly improved their moisture adsorption capabilities. The innovative application of EC coating addresses critical substrate adhesion issues, enhancing mechanical stability without compromising sensor sensitivity. Comprehensive performance evaluations revealed minimal hysteresis (

Active Measurement Of A Micron-Order Gap Under High-Speed And High-Temperature Conditions, Andrew Becker

Doctoral Dissertations and Master's Theses

The hypersonic regime poses numerous challenges that researchers face in the development of hypersonic flight vehicles. Due to their excellent thermomechanical properties, ultra-high-temperature ceramics (UHTCs) have risen as a promising solution to act as a protective barrier between the harsh environment and surface materials of these flight bodies. The mechanical operation of a portable hypersonic simulation device was developed in-house and tested at Argonne National Laboratories (ANL) to gather in-situ material response of prospective UHTC samples when exposed to a hypersonic regime. An edge detection-based algorithm was developed and used in LabVIEW to monitor the health and operation of the …

Effect Of Niobium Dopant On Zno Thin Films Prepared Via The Sol–Gel Spin Coating Method, Kevin Alvin Eswar, Nur Fairuz Rostan, Maryam Mohamad, Rabiatuladawiyah Md Akhir, Rosfayanti Rasmidi, Muliyadi Guliling, Najwa Ezira Azhar, Irmaizatussyehdany Buniyamin, Mohd Firdaus Malek, Mohamad Rusop Mahmood, Husairi Fadzilah Suhaimi, Saifollah Abdullah

Makara Journal of Science

Thin films of zinc oxide (ZnO) and niobium (Nb)-doped ZnO were deposited on a glass substrate using the sol–gel spin coating method. Diethanolamine, isopropyl alcohol, and zinc acetate served as the stabilizers, solvent, and starting ma-terial, respectively. Niobium pentachloride was employed as the dopant source. Energy-dispersive X-ray analysis con-firmed Nb incorporation. Field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), and ultravio-let–visible spectroscopy (UV–Vis) analyses characterized the morphology, structure, and optics of the films, respective-ly. Both films, comprising nanoparticles, were visible in FESEM. Nb doping reduced the particle size from 44.2 nm to 35.8 nm. The XRD peaks at 31.23°, …

Advancing Biofabrication Methodologies To Develop Biomimetic Tissue Scaffolds For Musculoskeletal Applications, Nashaita Yezdi Patrawalla

Theses and Dissertations

Musculoskeletal injuries impose a significant global burden, affecting millions and generating an economic toll exceeding $14 billion. Tissue engineering has gained traction as a promising strategy offering potential for functional restoration of damaged musculoskeletal tissues. This research aims to advance biofabrication techniques for generation of biomimetic tissue scaffolds, by optimizing scaffold design and modulating fabrication process parameters to generate scaffolds for musculoskeletal regeneration with application-specific tailored properties. In this realm, collagen-based biomaterials have been extensively investigated for tendon and ligamentous applications, and in combination with bioceramics incorporated into the collagen framework to produce composite scaffolds that better recapitulate the native …

Quantifying Chemomechanical Weakening In Muscovite Mica With A Simple Micromechanical Model, Jordan J. Sickle, William M. Mook, Frank W. Delrio, Anastasia G. Ilgen, Wendelin Wright, Karin A. Dahmen

Faculty Journal Articles

In response to gradual nanoindentation, the surface of muscovite mica deforms by sudden stochastic nanometer-scale displacement bursts. Here, the statistics of these displacement events are interpreted using a statistical model previously used to model earthquakes to understand how chemically reactive environments alter the surface properties of this material. We show that the statistics of nanoindentation displacement bursts in muscovite mica are tuned by chemomechanical weakening in a manner similar to how the statistics of model events are tuned by a mechanical weakening parameter that describes how easily system-spanning cracks can be nucleated. Because the predictions of this model are independent …

Advancements In Characterization Of Ancient Potteries From Southeast Asia: A Review Of Analytical Techniques, Chitnarong Sirisathitkul

Makara Journal of Science

Ancient potteries offer valuable information regarding technological advancements, life dynamics, cultural diversity, and trade routes in the past. Earthenware, stoneware, and porcelain from Southeast Asia have been characterized using several analytical techniques, as reviewed in this article. Fluorescent and diffracted X-rays give rise to elemental and phase compositions, respectively. Examination of molecular bonds requires vibrational spectroscopy, which is useful for the identification of organic materials in ancient potteries. With the advent of portable X-ray fluorescence and Raman spectrometry, on-site analysis of archeological ceramics is now possible. For in-depth analysis, synchrotron light sources can provide new insights into artifacts through X-ray …

Degradation Of The Mechanical Properties And Hydrogen Generation In Cement Under Gamma Irradiation Assessed By Atomistic Simulation, Omar Al Najjar

Theses and Dissertations

Although understanding the effect of the gamma-ray on cement-based materials is essential for many applications, such as the concrete contaminate of nuclear reactors or the storage of radioactive waste in cement-based waste forms, such understanding is still not fully developed. The importance of having such an understanding is becoming of utmost importance, especially with calls to extend the lifetime of nuclear power plants, and also due to some recent incidents of failures of the concrete structure in the nuclear fields. In this work, the details of preparing three molecular models as a representative structure of the main binding phase of …

Mechanisms Of Dendritic Shorting In Lithium Metal Batteries With Li7la3zr2o12 Solid Electrolytes, Lukas Karapin-Springorum

Pomona Senior Theses

Energy storage will play a crucial role in efforts to mitigate the effects of climate change caused by greenhouse gas emissions from human activity. Lithium metal batteries using solid electrolytes like Li₇La₃Zr₂O₁₂ have higher energy density than lithium-ion batteries, which may enable a more rapid and complete electrification of transportation. However, lithium metal batteries suffer from undesirable short-circuiting when metallic lithium deposits connect the two electrodes. It has been debated whether these lithium dendrites generally grow directionally from the anode or are generated by the reduction of lithium ions inside the solid electrolyte, …

Processing, Stability, And High-Temperature Properties Of Doped Lacro3-Based Refractory Ceramics And Composites For Harsh Environments Sensing Applications, Javier A. Mena

Graduate Theses, Dissertations, and Problem Reports (ETD)

In order to test and monitor the operational stability and conditions of various energy, transportation, and manufacturing systems and their components, accurate sensors capable of operating at temperatures over 1000 °C in various environments for long durations are required. In addition, many of these harsh environmental systems do not permit sensors to be directly inserted into the environment, so the sensors need to be embedded into the surrounding support or thermal protective materials. Some technological and industrial applications that require the use of harsh environment conditions sensing include nuclear and chemical reactors, jet engines, heavyduty gas turbines, rotating bearings in …

Development Of Interatomic Potential Of High Entropy Diborides With Artificial Intelligence Approach To Simulate The Thermo-Mechanical Properties, Nur Aziz Octoviawan

Graduate Theses/Dissertations

The interatomic potentials designed for binary/high entropy diborides and ultra-high temperature composites (UHTC) have been developed through the implementation of deep neural network (DNN) algorithms. These algorithms employed two different approaches and corresponding codes; 1) strictly local & invariant scalar-based descriptors as implemented in the DEEPMD code and 2) equivariant tensor-based descriptors as included in the ALLEGRO code. The samples for training and validation sets of the forces, energy, and virial data were obtained from the ab-initio molecular dynamics (AIMD) simulations and Density Functional Theory (DFT) calculations, including the simulation data from the ultra-high temperature region (> 2000K). The study …

Development Of High Kinetic Inductance Superconducting Nanowire Devices On High Permittivity Strontium Titanate Substrates, Jamie Timmons

UNF Graduate Theses and Dissertations

This thesis involves the fabrication and characterization of devices made from two different superconducting materials: yttrium barium copper oxide (YBCO), a high-TC complex oxide, and niobium nitride (NbN), a low-TC transition metal nitride. Both types of devices are fabricated on strontium titanate substrates, which provides a good lattice match to YBCO and also an extremely large permittivity at low temperature. We demonstrate that wet etching of YBCO thin films via bromine can be a viable microfrabriation technique for the material. Using approximately 35 nm thick epitaxially grown YBCO on an STO substrate, we were able to fabricate YBCO “microwires” with …

Developing Positive Thermal Coefficient (Ptc) Heaters For Solar Electric Cooking, Katarina Ivana Brekalo, Andrew Shepherd

Physics

Positive Thermal Coefficients, PTCs, are materials that abruptly change in resistance in response to changes in temperature. The purpose of this experiment is to explore the viability of using the switching type ceramic PTC thermistor as a replacement for current resistive heaters. These types of PTCs have a nonlinear change in resistance with increases in temperature. This device will be used as a temperature-controlling heating element intended to power an Insulated Solar Electric Cooker (ISEC). The ISEC is designed to cook meals throughout the day for impacted communities as an alternative cooking method that doesn’t require biofuel as an energy …

Modeling, Fabrication, And Characterization Of Rf-Based Passive Wireless Sensors Composed Of Refractory Semiconducting Ceramics For High Temperature Applications, Kavin Sivaneri Varadharajan Idhaiam

Graduate Theses, Dissertations, and Problem Reports (ETD)

Real-time health monitoring of high temperature systems (>500^oC) in harsh environments is necessary to prevent catastrophic events caused by structural failures, varying pressure, and chemical reactions. Conventional solid-state temperature sensors such as resistance temperature detectors (RTDs) and thermocouples are restricted by their operating environments, sensor dimensions and often require external power sources for their operation. The current work presents the research and development of RF-based passive wireless sensing technology targeting high temperatures and harsh environmental conditions. Passive wireless devices are generally classified as near-field and far-field devices based on the interrogation distance. Near-field sensors are placed at …

Study Of Static And Dynamical Properties Of Complex Antiferroelectrics Materials, Kinnary Yogeshbhai Patel

Graduate Theses and Dissertations

The aim of this dissertation is the investigation of the static and dynamical properties of the complex antiferroelectric materials using Effective Hamiltonian method and First principles calculations. In chapter 3, a novel elemental interatomic coupling in perovskite materials which bilinearly couples the antiferroelectric displacements of cations with the rotations of the oxygen octahedra. This new coupling explains a very complex crystal structure of prototypical antiferroelectric PbZrO3. My explanation provides a unified description of many other complex antipolar crystal structures in variety of perovskite materials, including the occurrence of incommensurate phases in some of them. In chapter 4, results and analysis …

Study Of Amorphous Boron Carbide And Hydrogenated Boron Carbide Materials Using Molecular Dynamics And Hybrid Reverse Monte Carlo, Rajan Khadka

Graduate Theses/Dissertations

We present a computational study of amorphous boron carbide (a-B_xC) models using Molecular Dynamics (MD) studied with Stillinger-Weber (SW) and ReaxFF potential. The atomic structure factor (S(Q)), radial distribution function (RDF) and bond lengths comparison with other experimental and ab initio models shows that a random arrangement of icosahedra (B₁₂, B₁₁C) interconnected by chains (CCC, CBC) are present in a-B_xC. Afterward, Hybrid Reverse Monte Carlo (HRMC) technique is used to recreate a-B_xC structures. The existing SW potential parameters of Boron are optimized for the α-rhombohedral (Icosahedral B_{12 …}

Nonlinear Optical Studies Of Defects And Domain Structures In Perovskite-Type Dielectric Ceramics, David J. Ascienzo

Dissertations, Theses, and Capstone Projects

In order to improve future generations of dielectric capacitors a deeper understanding of voltage-induced dielectric breakdown and electrical energy storage limitations is required. This dissertation presents the use of far-field optical second harmonic generation (SHG) polarimetry for probing structural defects and polar domains in linear and nonlinear perovskite dielectric ceramics. We investigated the formation of electric field-induced structural distortions at pristine Fe-doped SrTiO₃ (Fe:STO) electrode interfaces, structural defect and strain formation due to oxygen vacancy migration in electrodegraded Fe:STO single crystals, and mixed tetragonal and rhombohedral phase domains in ferroelectric Zr-doped BaTiO₃ (BZT) films exhibiting excellent …

Investigation Of Electric Field–Induced Structural Changes At Fe-Doped Srtio3 Anode Interfaces By Second Harmonic Generation, David Ascienzo, Haochen Yuan, Steven Greenbaum, Thorsten J. Bayer, Russell A. Maier, Jian-Jun Wang, Clive A. Randall, Elizabeth C. Dickey, Haibin Zhao, Yuhang Ren

Publications and Research

We report on the detection of electric field–induced second harmonic generation (EFISHG) from the anode interfaces of reduced and oxidized Fe-doped SrTiO3 (Fe:STO) single crystals. For the reduced crystal, we observe steady enhancements of the susceptibility components as the imposed dc-voltage increases. The enhancements are attributed to a field-stabilized electrostriction, leading to Fe:Ti-O bond stretching and bending in Fe:Ti-O6 octahedra. For the oxidized crystal, no obvious structural changes are observed below 16 kV/cm. Above 16 kV/cm, a sharp enhancement of the susceptibilities occurs due to local electrostrictive deformations in response to oxygen vacancy migrations away from the anode. Differences between …

Verifying The Implementation Of An Anisotropic Grain Boundary Energy Model In Idaho National Lab’S Marmot, John-Michael H. Bradley, Evan D. Hansen, Jarin C. French, Yongfeng Zhang (Mentor)

Idaho Conference on Undergraduate Research

This work aims to verify the correct implementation of an anisotropic grain boundary (GB) energy model for face-centered cubic (FCC) and fluorite materials in Idaho National Laboratory’s phase field fuel performance code MARMOT. The model was recently implemented in MARMOT with the purpose of enabling higher fidelity simulations of UO₂ nuclear fuels. As part of verification, tests were performed to measure the energy dependence on misorientation of high symmetry GBs in an FCC metal (Cu). The energies of the [100], [110], and [111] twist boundaries result as predicted, as do the energies of the [111] symmetric tilt boundaries. However, …

High Pressure Behavior Of Mullite-Type Oxides: Phase Transitions, Amorphization, Negative Linear Compressibility And Microstructural Implications, Patricia Kalita

UNLV Theses, Dissertations, Professional Papers, and Capstones

Even though mullite occurs rarely in nature, it is perhaps one of the most important phases in both traditional and advanced ceramics. Existing and emerging applications of mullite and mullite-type materials include: high-temperature composites, aerospace materials, ballistic shielding for military applications and even non-linear optical materials. There are many uncertainties regarding the basic physical properties of mullite-type materials, particularly in terms of their high-pressure structural stability and mechanical behavior that are important to address for emerging applications of mullites as engineering materials. This work is the first reported comprehensive investigation of the high –pressure structural behavior of several different mullites …

Crystal Nucleation Of Palladium-Doped Lithium Disilicate Glass, Gregory Humble

Symposium of Student Scholars

The effect of concentration of palladium particles on crystal nucleation was investigated for lithium disilicate glass. The heterogeneous nucleation rate for 470°C and 480°C were calculated for a concentration of 0.001% palladium by weight. The DTA method of measuring nucleation and crystallization was used in this calculation.

Synthesis, Field Emission And Associated Degradation Mechanisms Of Tapered Zno Nanorods, Gregory M. Wrobel Mr.

Master's Theses

Equation 1..... 4

Equation 2..... 4

Equation 3..... 6

Equation 4..... 7

Equation 5..... 9

Equation 6..... 10

Equation 7..... 11

Equation 8..... 12

Equation 9..... 14

Equation 10..... 40

Equation 11..... 51

Synthesis, Field Emission and Associated Degradation Mechanisms of Tapered ZnO Nanorods

Gregory Michael Wrobel, M.S.

University of Connecticut, 2011

Modern development of field emitter arrays (FEA) has been made possible, partly thanks to the synthesis and development of one-dimensional (1D) nanostructures. High aspect ratio 1D nanostructures effectively amplify the electric field at the emitter tips, allowing electrons to be extracted at relatively low electric field. An inexpensive …

Yttrium And Hydrogen Superstructure And Correlation Of Lattice Expansion And Proton Conductivity In The Bazr0.9y0.1o2.95 Proton Conductor, A. Braun, A. Ovalle, V. Pomjakushin, A. Cervellino, S. Erat, Wayne C. Stolte, T. Graule

Chemistry and Biochemistry Faculty Research

Bragg reflections in Y-resonant x-ray diffractograms of BaZr_0.9Y_0.1O_2.95 (BZY10) reveal that Y is organized in a superstructure. Comparison with neutron diffraction superstructure reflections in protonated/deuterated BZY10 suggests that both superstructures are linked, and that protons move in the landscape imposed by the Y. The thermal lattice expansion decreases abruptly for protonated BZY10 at T≥648±20 K, coinciding with the onset of lateral proton diffusion and suggesting a correlation of structural changes and proton conductivity. The chemical shift in the Y L₁-shell x-ray absorption spectra reveals a reduction from Y³⁺ toward Y²⁺ upon …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix, Kenneth Czerwinski

Fuels Campaign (TRP)

This project will examine inert fuels containing ZrO₂ and MgO as the inert matrix. Ceramics with this inert matrix, Ce, U and eventually Pu will be synthesized and examined. While the Advanced Fuel Cycle Initiative focus is on inert fuels with Pu as the fissile component, this task will perform initial laboratory experiments with Ce and U. The initial work with Ce will be performed early in the project with results used as a basis for U studies. Reactor physics calculations will be used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf. …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix, Kenneth Czerwinski

Fuels Campaign (TRP)

This project will examine inert fuels containing ZrO₂ and MgO as the inert matrix. Ceramics with this inert matrix, Ce, U and eventually Pu will be synthesized and examined. While the Advanced Fuel Cycle Initiative focus is on inert fuels with Pu as the fissile component, this task will perform initial laboratory experiments with Ce and U. The initial work with Ce will be performed early in the project with results used as a basis for U studies. Reactor physics calculations will be used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf. …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix: Quarterly Report, January 2006 To March 2006, Kiel Steven Holliday, Thomas Hartmann, Kenneth Czerwinski

Fuels Campaign (TRP)

This project will examine inert matrix fuels containing ZrO₂ and MgO as the inert matrix, with the relative amount of MgO varied from 30% to 70% in ZrO₂. Reactor physics calculations will be used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf with reactor grade Pu providing the fissile component, with up to 10% of ²³⁹Pu. Ceramics will be synthesized and characterized based on the reactor physics results. The solubility of the fuel ceramics, in reactor conditions, reprocessing conditions, and repository conditions, will be investigated in a manner to …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix, Kenneth Czerwinski

Fuels Campaign (TRP)

This project examines inert fuels containing ZrO₂ and MgO as the inert matrix, with the relative amount of MgO varied from 30% to 70% in ZrO₂. Reactor physics calculations are used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf with reactor grade Pu providing the fissile component, with up to 10% of ²³⁹Pu. Ceramics are synthesized and characterized based on the reactor physics results. The solubility of the fuel ceramics, in reactor conditions, reprocessing conditions, and repository conditions, are investigated in a manner to provide thermodynamic data necessary for …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix: Quarterly Report, April 2005 To June 2005, Earl Wolfram, Thomas Hartmann, Kenneth Czerwinski

Fuels Campaign (TRP)

This project will examine inert matrix fuels containing ZrO₂ and MgO as the inert matrix, with the relative amount of MgO varied from 30% to 70% in ZrO₂. Reactor physics calculations will be used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf with reactor grade Pu providing the fissile component, with up to 10 % of ²³⁹Pu. Ceramics will be synthesized and characterized based on the reactor physics results. The solubility the fuel ceramics, in reactor conditions, reprocessing conditions, and repository conditions, will be investigated in a manner to …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix: Quarterly Report, January 2005 To March 2005, Earl Wolfram, Thomas Hartmann, Kenneth Czerwinski

Fuels Campaign (TRP)

This project will examine inert matrix fuels containing ZrO₂ and MgO as the inert matrix, with the relative amount of MgO varied from 30% to 70% in ZrO₂. Reactor physics calculations will be used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf with reactor grade Pu providing the fissile component, with up to 10% of ²³⁹Pu. Ceramics will be synthesized and characterized based on the reactor physics results. The solubility the fuel ceramics, in reactor conditions, reprocessing conditions, and repository conditions, will be investigated in a manner to provide …

Dissolution, Reactor, And Environmental Behavior Of Zro2-Mgo Inert Fuel Matrix, Kenneth Czerwinski

Fuels Campaign (TRP)

This project examines inert fuels containing ZrO₂ and MgO as the inert matrix, with the relative amount of MgO varied from 30% to 70% in ZrO₂. Reactor physics calculations are used to examine suitable quantities of burnable poisons from the candidate elements Gd, Er, or Hf with reactor grade Pu providing the fissile component, with up to 10% of ²³⁹Pu. Ceramics are synthesized and characterized based on the reactor physics results. The solubility of the fuel ceramics, in reactor conditions, reprocessing conditions, and repository conditions, are investigated in a manner to provide thermodynamic data necessary for …

Intermetallic Reactions In Vacuum-Deposited Nickel And Gold Films On (111) Silicon Single Crystals, K. H. Yoon, Gordon Lewis, L. L. Levenson

Materials Science and Engineering Faculty Research & Creative Works

Pure nickel and gold thin films were vacuum-deposited on (111) silicon single crystals. When Ni/Au/Si or Au/Ni/Si samples were heated to about 550° in situ, hexagonal or deformed hexagonal shaped crystallites were formed on the silicon substrates. The composition of these crystallites was determined by using x-ray diffraction, scanning electron microscopy and scanning Auger microprobe methods. The crystallites were identified as NiSi2. The crystal-lites on the (111) silicon plane parallel to the surface appeared as regular hexagons while the inclined crystal-lites resembled trapezia. The results of Auger spectra and in-depth composition profiles for Ni, Au, and Si showed that the …