Ceramic Materials Commons^™

Kinetic Modeling Of Electrostatic Sieving For Lunar Regolith Beneficiation: Case Studies, Easton Ingram, Emmanuela Amen Eze, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

A new kinetic particle modeling framework was developed to investigate electrostatic transport of lunar regolith particles with applications to the concept of electrostatic sieving. the new approach is based on kinetic particle dynamics and includes major modules of sampling the particle size distribution, solving electric fields, and tracking motion of charged dust grains. Case studies for a concept of electrostatic sieving were chosen to validate the new model. the simulation achieved similar yields reported in previous works, which served as validation of the model. the new model is computationally efficient and could serve as a design, analysis, and optimization tool.

Progress Of Lisap-Mse: A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, David Bayless, Daniel Stutts, Daoru Han, Todd P. Sander, Jeffrey Smith, Fateme Rezaei, William Schonberg

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Ultra-Fast Annealing Improves Snr And Long-Term Stability Of A Highly Multiplexed Line-By-Line Fbg Array Inscribed By Femtosecond Laser In A Coreless Fiber For Extreme-Temperature Applications, Farhan Mumtaz, Bohong Zhang, Jeffrey D. Smith, Ronald J. O'Malley, Rex E. Gerald, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

This study reports the fabrication of an 4th-order line-by-line Fiber Bragg Gratings (FBG) array using femtosecond laser inscription within a highly multimode coreless optical fiber, with a particular focus on achieving substantial multiplexing capabilities. An ultra-fast annealing procedure is employed, resulting in an impressive enhancement of the FBG sensor's fringe visibility by approximately 13 dB, signifying a notable improvement of approximately ~4 dB. This substantial enhancement contributes to the long-term stability and performance of the multiplexed FBG array in extreme temperature conditions. The systematic fabrication approach employed for the multiplexed FBG array guarantees a high signal-to-noise ratio (SNR) for each …

Experimental Investigation Of A Viscoelastic Liner To Reduce Under Helmet Overpressures And Shock Wave Reflections, Cody J.H. Thomas, Fatih Dogan, Catherine E. Johnson

Materials Science and Engineering Faculty Research & Creative Works

Introduction: Shock wave overpressure exposures can result in blast-induced traumatic brain injury (bTBI) in warfighters. Although combat helmets provide protection against blunt impacts, the protection against blast waves is limited due to the observed high overpressures occurring underneath the helmet. One route to enhance these helmets is by incorporating viscoelastic materials into the helmet designs, reducing pressures imposed on the head. This study aims to further investigate this mitigation technique against under-helmet overpressures by adding a viscoelastic liner to the inside of a combat helmet. Methods: The liner's effectiveness was evaluated by exposing it to free-field blasts of Composition C-4 …

Electrostatic Sorting Of Lunar Regolith Simulants For Sustainable Resource Utilization: Modeling And Characterization Of Particle Size Distribution, Abdullah Al Moinee, Peter Bachle, Kyle Newport, William Schonberg, David Bayless, Jeffrey Smith, Daoru Han, Fateme Rezaei

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In pursuit of sustainable resource utilization on the Moon, this paper delves into modeling and characterization of particle size distribution (PSD) of lunar regolith simulants in an electrostatic system. a prototype electrostatic sieve was built and tested with four sample simulants mirroring properties of lunar mare and highland regolith. an alternating four-phase (90 degrees, 180 degrees, 270 degrees, 360 degrees) traveling square-wave was utilized for particle-directed transport to model the diverse trajectories of the particles. Numerically, we scrutinized how the distribution functions of the particles are manifested as the electrostatic field propagates, with a focus on three distinct particle ranges …

Molecular Modeling Of Phenolic Resin For Carbon-Carbon Composites, Ivan Gallegos

Dissertations, Master's Theses and Master's Reports

One of the most difficult challenges associated with space exploration is terrestrial atmospheric reentry due to the high thermal loads generated. Carbon carbon (C/C) composites have been used as heat shielding materials due to their high strengthto- weight ratio and thermal properties and their applications include heat shielding for various high temperature environments. C/C composites are manufactured by polymer-infiltration pyrolysis (PIP) via cycles of curing and pyrolysis of a prepreg which can be costly and take up to several days. Thus, C/C composites ideal candidates for computationally-driven optimization techniques, such as a multiscale Integrated Computational Materials Engineering (ICME) approach, by …

Mechanisms Of Dendritic Shorting In Lithium Metal Batteries With Li7la3zr2o12 Solid Electrolytes, Lukas Karapin-Springorum

Pomona Senior Theses

Energy storage will play a crucial role in efforts to mitigate the effects of climate change caused by greenhouse gas emissions from human activity. Lithium metal batteries using solid electrolytes like Li₇La₃Zr₂O₁₂ have higher energy density than lithium-ion batteries, which may enable a more rapid and complete electrification of transportation. However, lithium metal batteries suffer from undesirable short-circuiting when metallic lithium deposits connect the two electrodes. It has been debated whether these lithium dendrites generally grow directionally from the anode or are generated by the reduction of lithium ions inside the solid electrolyte, …

Calculation Of Elastic Constants Of Bulk Metallic Glasses From Indentation Tests, Zhitong Xu, Ming Liu, Fuqian Yang

Chemical and Materials Engineering Faculty Publications

One of the challenges in the applications of instrumented indentation is to simultaneously measure elastic modulus and Poisson’s ratio of homogeneous, isotropic materials. This work proposes empirical equations for simultaneous calculation of elastic modulus and Poisson’s ratio of bulk metallic glasses (BMGs) from the ratio of the short diagonal length to the long diagonal length and the area of the Knoop imprint. The parameters pre- sented in the empirical equations are determined first by Knoop microhardness tests of 24 BMGs, whose elastic moduli and Poisson’s ratios are measured by resonant ultrasound spectroscopy. These empirical equations are further validated by the …

Bioprinting With Adipose Stem Cells And Hydrogel Modified With Bioactive Glass, Krishna C.R. Kolan, Apurv Saxena, Bradley A. Bromet, Lesa B. Steen, August T. Bindbeutel, Julie A. Semon, Delbert E. Day, Ming C. Leu

Biological Sciences Faculty Research & Creative Works

Bioprinting research is focused on utilizing growth factors and multiple cell types to create clinically relevant three-dimensional (3D) tissue models using hydrogels. Rheological and biological challenges are two main factors that limit the creation of extrudable bioactive hydrogels. In this study, we investigate incorporation of fast dissolving and bioactive borate glass in different weight to volume percentages (0.075 to 0.6%) to alginate-gelatin (1:1) hydrogel to improve rheological properties and enable bioprinting with bioactive glass. The addition of glass improved the stiffness of the hydrogel. Human adipose-derived mesenchymal stem cells (ASCs) were uniformly mixed in this bioink at 1 x 106 …

Cf/Sic Ceramic Matrix Composites With Extraordinary Thermomechanical Properties Up To 2000 °C, Min Sung Park, Jian Gu, Heesoo Lee, Sea Hoon Lee, Lun Feng, William Fahrenholtz

Materials Science and Engineering Faculty Research & Creative Works

The thermomechanical properties of carbon fiber reinforced silicon carbide ceramic matrix composites (Cf/SiC CMCs) were studied up to 2000 °C using high temperature in situ flexural testing in argon. The CMC specimens were fabricated using an ultrahigh concentration (66 vol%) aqueous slurry containing nano-sized silicon carbide powder. The SiC powder compacts were obtained by drying the slurry and were densified using the precursor impregnation and pyrolysis (PIP) method with field assisted sintering technology/spark plasma sintering (FAST/SPS). The high relative density of the SiC green body (77.6%) enabled densification within 2.5 days using four PIP cycles. In contrast, conventional PIP processes …

Thermodynamic Analysis Of Metal Segregation In Dual Phase High Entropy Ceramics, Steven M. Smith, William G. Fahrenholtz, Gregory E. Hilmas, Stefano Curtarolo

Materials Science and Engineering Faculty Research & Creative Works

Equilibrium Gibbs' free energy calculations were used to determine metal segregation trends between boride and carbide solid solutions containing two metals that are relevant to dual phase high entropy ceramics. The model predicted that Ti had the strongest tendency to segregate to the boride phase followed by Zr, Nb, Mo, V, Hf, and Ta, which matches experimental results of measured compositions. The ratio of a metal in the carbide phase to the content of the same metal in the corresponding metal boride had a linear trend with the change in standard Gibbs' free energy of reaction for a metal carbide …

Spark Plasma Sintering Of Magnesium Titanate Ceramics, Suzana Filipović, Nina Obradović, William G. Fahrenholtz, Steven Smith, Miljana Mirković, Adriana Peleš Tadić, Jovana Petrović, Antonije Đorđević

Materials Science and Engineering Faculty Research & Creative Works

Magnesium titanate ceramics were prepared by reactive spark plasma sintering (SPS) at 1200 °C for 5 min. Prior to sintering, MgO and TiO₂ powders were mixed by high energy ball milling (HEBM) for 15, 30, or 60 min. The effect of milling time on phase composition was analyzed by X-ray diffraction (XRD) for milled powders and sintered specimens. The morphology of the sintered ceramics was investigated by scanning electron microscopy (SEM), while elemental distribution was determined by energy dispersive spectroscopy (EDS). The presence of the MgTi2O5 phase was detected in XRD and was confirmed by EDS analysis. Microcracking was …

A Super-Hard High Entropy Boride Containing Hf, Mo, Ti, V, And W, Suzana Filipovic, Nina Obradovic, Greg E. Hilmas, William G. Fahrenholtz, Donald W. Brenner, Jon Paul Maria, Douglas E. Wolfe, Eva Zurek, Xiomara Campilongo, Stefano Curtarolo

Materials Science and Engineering Faculty Research & Creative Works

Super-Hard (Hf,Mo,Ti,V,W)B2 Was Synthesized by Boro-Carbothermal Reduction and Densified by Spark Plasma Sintering. This Composition Was Produced for the First Time as a Single-Phase Ceramic in the Present Research. the Optimized Ceramic Had a Single Hexagonal AlB2-Type Crystalline Phase with a Grain Size of 3.8 µm and Homogeneous Distribution of the Constituent Metals. the Vickers Hardness Exhibited the Indentation Size Effect, Increasing from 27 GPa at a Load of 9.8 N to as High as 66 GPa at a Load of 0.49 N. This is the Highest Hardness Reported to Date for High Entropy Boride Ceramics.

Oxidation Of Additively Manufactured Zrb2–Sic In Air And In Co2 At 700–1000 °C, Marharyta Lakusta, Nicholas M. Timme, Abid H. Rafi, Jeremy Lee Watts, M. (Ming) C. (Chuan) Leu, Gregory E. Hilmas, William G. Fahrenholtz, David W. Lipke

Materials Science and Engineering Faculty Research & Creative Works

Oxidation behavior of additively manufactured zrb2–sic in air and in co2 is reported in the temperature range of 700–1000 °c. Observed scale morphologies in air and in co2 were similar, featuring an outer borosilicate layer and an inner porous zirconia layer containing partially oxidized silicon carbide particles and remnant borosilicate products. Oxide scale thicknesses and parabolic scaling constants in air were approximately twice those observed in co2 across all studied temperatures. Activation energies for oxidation of 140 ± 20 kj/mol in air and 110 ± 20 kj/mol in co2 were determined, indicating similar diffusion processes that appear to be rate-limiting. …

Thermal And Electrical Properties Of Single-Phase High Entropy Carbide Ceramics, Paul M. Brune, Gregory E. Hilmas, William G. Fahrenholtz, Jeremy Lee Watts, Stefano Curtarolo

Materials Science and Engineering Faculty Research & Creative Works

Thermal and Electrical Properties Were Investigated for Five Nominally Phase-Pure High Entropy Carbide Ceramics. the Compositions (Hf0.2Nb0.2Ta0.2Ti0.2Zr0.2)C, (Cr0.2Hf0.2Ta0.2Ti0.2Zr0.2)C, (Hf0.2Mo0.2Ta0.2Ti0.2Zr0.2)C, (Hf0.2Ta0.2Ti0.2W0.2Zr0.2)C, and (Hf0.2Mo0.2Ti0.2W0.2Zr0.2)C Were Synthesized by Carbothermal Reduction of Oxides. the Thermal Diffusivity and Heat Capacity Were Measured from Room Temperature to 1800°C. the Room Temperature Thermal Conductivity Ranged from 5.1 W/mK for (Hf0.2Mo0.2Ti0.2W0.2Zr0.2)C to 9.0 W/mK for (Cr0.2Hf0.2Ta0.2Ti0.2Zr0.2)C. the Thermal Conductivity Increased over the Temperature Range with Maximum Conductivities of 19.6 W/mK Measured for (Hf0.2Mo0.2Ta0.2Ti0.2Zr0.2)C to 29.7 W/mK for (Cr0.2Hf0.2Ta0.2Ti0.2Zr0.2)C at 1800°C. the Electron Contribution to Thermal Conductivity Calculated from Measured Electrical Resistivity Varied from 41% to 52% of the …

Beneficiation Of Lunar Regolith Simulants Through Electrostatic Sieving And Magnetic Separation, Peter Bachle, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

In the light of future development of lunar structures, in-situ feldspar beneficiation is imperative for metal extraction. This research incorporates the tandem use of electrostatic sieving and magnetic separation for collecting a specific size range and mineral composition from lunar soil that optimizes subsequent chemical processing. While earlier works focused on silt-sized particles, this work expands that range up to medium-grained sand with a greater variety of potential lunar regolith compositions. This work shows that a 2.5 kV, 7 Hz to 30Hz frequency, single-phase square wave can lift silt and fine sand for collection. This lifting is successful directly from …

Strength Comparison For Fully Dense Zirconium Diboride Ceramics Tested By Different Methods, Darko Kosanović, Suzana Filipović, Isaak Trajković, Nina Obradović, Paul M. Brune, Gregory E. Hilmas, William G. Fahrenholtz

Materials Science and Engineering Faculty Research & Creative Works

The strength of zirconium diboride ceramics was tested by three different methods, 3-point flexure, 4-point flexure, and compression. Nearly full-density ceramics were obtained by hot pressing commercial ZrB₂ powder with the addition of.5 wt.% carbon as a sintering aid. The thermal properties and hardness were studied for ZrB₂ milled with ZrB₂ and WC media. Based on phase purity and higher thermal conductivity, ZrB₂ ceramics prepared from powders milled with ZrB₂ media were selected for mechanical property studies. The strength in 3-point flexure was 546 ± 55 MPa. The flexure strength was 476 ± 41 MPa …

Kinetic Modeling Of Electrostatic Sieving For Lunar Regolith Beneficiation: Case Studies, Easton Ingram, Emmanuela Amen Eze, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

A new kinetic particle modeling framework was developed to investigate electrostatic transport of lunar regolith particles with applications to the concept of electrostatic sieving. The new approach is based on kinetic particle dynamics and includes major modules of sampling the particle size distribution, solving electric fields, and tracking motion of charged dust grains. Case studies for a concept of electrostatic sieving were chosen to validate the new model. The simulation achieved similar yields reported in previous works, which served as validation of the model. The new model is computationally efficient and could serve as a design, analysis, and optimization tool.

Synergistic Hardening In A Dual Phase High-Entropy (Hf,Nb,Ta,Ti,Zr)C–(Hf,Nb,Ta,Ti,Zr)B2 Ultra-High Temperature Ceramic, Rubia Hassan, William G. Fahrenholtz, Gregory E. Hilmas, Stefano Curtarolo

Materials Science and Engineering Faculty Research & Creative Works

A dual phase high-entropy (Hf,Nb,Ta,Ti,Zr)C–(Hf,Nb,Ta,Ti,Zr)B2 ultra-high temperature ceramic was synthesized using a single step boro-carbothermal reduction route. The synthesized powder was densified by spark plasma sintering at 2000°C, resulting in complete solid solution formation and a relative density of ≈99%. The dual phase ceramic was 43 vol% high-entropy carbide and 57 vol% high-entropy boride. The grain sizes were 0.85 ± 0.34 µm for the carbide and 0.87 ± 0.33 µm for the boride with minimal residual oxide (0.2 vol%) detected in the microstructure. The resulting composition had a higher microhardness than the individual boride and carbide ceramics across the range …

Development Of A Highly Loaded Zirconium Carbide Paste For Material Extrusion Additive Manufacturing, Clare Sabata, Austin J. Martin, Jeremy L. Watts, Gregory E. Hilmas

Materials Science and Engineering Faculty Research & Creative Works

A highly loaded, aqueous-based zirconium carbide (ZrC) paste was developed for ceramic on-demand extrusion (CODE). Commercial ZrC powder was ball milled to reduce the particle size to ∼1 μm. Paste composition was determined by rheological characterization and observation of printing behavior; the final paste consisted of 46–47 vol% ZrC, 43.5 vol% distilled water, 8.1 vol% dispersant, and 1.6 vol% binder. Rheological characterization of the paste showed a yield stress of ∼8 Pa and shear thinning behavior (ΔG′/Δσ* = −55). The paste was printed using a 610 μm nozzle; a test print showed shape fidelity using the developed paste. A pressureless …

Magnetic Separation Of Lunar Regolith Simulants With Applications To In Situ Resource Utilization On The Moon, Peter Bachle, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

The development of in situ resource utilization (ISRU) for metal extraction is imperative as a steppingstone for habitation construction in lunar and non-terrestrial environments. Separation of minerals by chemical composition is important to optimize metal and oxygen liberation from lunar ore. to this effect, devices capable of separating aluminum bearing minerals from iron-bearing minerals from the lunar regolith simulants have been developed. Twenty-eight different simulants have been used in this study. a dual-belt separator was designed to reduce middlings. Para-magnetic minerals were reliably separated using a neodymium N52-magnet-separator system. Effective separation of aluminum-bearing minerals from iron-bearing minerals was greater than …

A Concept Of Producing Aluminum In-Situ On The Moon Through Molten Salt Electrolysis, Jacob N. Ortega, Jeffrey Smith, Fateme Rezaei, David Bayless, William Schonberg, Daniel Stutts, Daoru Han

Materials Science and Engineering Faculty Research & Creative Works

This paper presents a concept of producing aluminum in-situ on the lunar surface, namely, the Lunar In-Situ Aluminum Production through Molten Salt Electrolysis (LISAP-MSE) method developed at Missouri University of Science and Technology. This paper aims to demonstrate the use of electro-deoxidation to reduce aluminum oxide (i.e., alumina) into aluminum and oxygen gas via electrolysis in a molten salt bath for the production of aluminum on the Moon. It is shown that with a steady supply of hydrogen chloride, this in-situ resource utilization (ISRU) method could supply several necessary materials consumed in the electro-deoxidation process except hydrogen chloride to produce …

Bipolar Hipims Kick-Pulse For High Hardness In High-Entropy Boride Thin Films, Nathaniel S. Mcilwaine, Nestor O.Marquez Rios, Eva Zurek, Donald W. Brenner, William G. Fahrenholtz, Stefano Curtarolo, Douglas E. Wolfe, Jon Paul Maria

Materials Science and Engineering Faculty Research & Creative Works

We report a microhardness indentation study for multicomponent refractory metal boride thin films that belong to the family of high-entropy ceramics exhibiting superior hardness and high temperature properties. We focus on the nominally equimolar composition (Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2) B2, which we refer to as HEB3, on c-plane sapphire substrates. Thin films are prepared using bipolar high power impulse magnetron sputtering (HiPIMS), where the positive kick pulse is optimized to produce films with high density, high crystallinity, and a microstructure that is isometric in nature as revealed by cross-sectional fracture surface imaging, X-ray diffraction, and X-ray reflectometry. Low-load Knoop indentation is used to …

Sic Addition To A Dual Phase High Entropy Ultra-High Temperature Ceramic, Rubia Hassan, William G. Fahrenholtz, Kantesh Balani, Gregory E. Hilmas, Jeremy Watts

Materials Science and Engineering Faculty Research & Creative Works

Dual phase (Hf,Ta,Ti,W,Zr)B2-(Hf,Ta,Ti,W,Zr)C high entropy ultra-high temperature ceramics were processed from commercial diboride and carbide powders with and without SiC additions. A 30-min hold at a maximum temperature of 1850 °C in spark plasma sintering resulted in a relative density of ∼95 %, which increased to ∼100 % with the addition of 7.5 wt.% SiC. The compositions did not reach chemical equilibrium under the given sintering conditions resulting in an inhomogeneous distribution of transition metals in both the boride and carbide phases. The addition of SiC improved densification by inhibiting grain growth, which reduced the grain size from 9.0 ± …

Ambient Temperature Strength Degradation Of A Ceramic Matrix Composite Due To Solid Particle Erosion, Jonathan Clawson

Williams Honors College, Honors Research Projects

Solid particle erosion (SPE) is an issue for aircraft exposed to hard, fine particles, such as sand or dust, that can be ingested into the engine at a high velocity without reaching their melting point, resulting in material removal. SPE can be attributed to the intake of particulate debris from the runway or from airborne particulates. The cumulative mass loss from SPE damage affects the structural integrity and performance of the engine; however, its effects on ceramic matrix composites (CMCs), that are being employed in the aerospace industry, are not well understood in literature. The limited SPE research studies that …

Investigation Of Mechanically Fatigue Low-Frequency Energy Harvesting Effects On Isotropic Materials, Daniel J. Meade

College of Graduate Studies: Theses & Dissertations

This research project reports an exploratory investigation of energy harvesting effect on isotropic material that goes through low frequency mechanical fatigue. Energy harvesting is a growing field of study that can recycle ambient energy back into a system that would otherwise be lost. This is a significantly useful method for the ongoing energy crisis and provides an alternate route to design and upgrade systems to be more efficient and last longer than current system designs. However, it is time to investigate if there is any effect vibration-based energy harvesting has on the structure from which energy is being harvested. To …

Photoexcited Charge Carrier Dynamics And Electronic Properties Of Two-Dimensional Mxene, Nb2ctx, Andrew M. Fitzgerald, Emily Sutherland, Tarek A. Elmelegy, Mary Qin Hassig, Julia Martin, Erika Colin-Ulloa, Ken Ngo, Ronald L. Grimm, Joshua R. Uzarski, Michel W. Barsoum, N. Aaron Deskins, Lyubov V. Titova, Kateryna Kushnir Friedman

Mechanical Engineering

Two-dimensional, 2D, niobium carbide MXene, Nb2CTx, has attracted attention due to its extraordinarily high photothermal conversion efficiency that has applications ranging from medicine, for tumor ablation, to solar energy conversion. Here, we characterize its electronic properties and investigate the ultrafast dynamics of its photoexcitations with a goal of shedding light onto the origins of its unique properties. Through density functional theory, DFT, calculations, we find that Nb2CTx is metallic, with a small but finite density of states at the Fermi level for all experimentally relevant terminations of Nb2CTx that can be achieved using HF or molten salt etching of the …

Far-Field Passive Wireless Sensors Composed Of Electroceramic Materials For Harsh Environment Applications, Kevin M. Tennant

Graduate Theses, Dissertations, and Problem Reports (ETD)

The demand for high temperature sensing technologies in industrial applications has been steadily increasing, driven by the need for precise monitoring and control in extreme environments. This thesis presents an investigation into the development and optimization of passive wireless sensors for high temperature sensing applications. The research focuses on overcoming the challenges associated with traditional sensing methods by leveraging passive wireless sensor technology, offering advantages such as reduced complexity, improved reliability, and enhanced flexibility.

A passive wireless high temperature sensor for far-field applications was developed for stable temperature sensing up to 1000 °C. The goal is to leverage the properties …

Femtosecond Laser–Inscribed Fiber Bragg Grating Sensors: Enabling Distributed High- Temperature Measurements And Strain Monitoring In Steelmaking And Foundry Applications, Ogbole Collins Inalegwu, Yeshwanth Reddy Mekala, Rony Kumer Saha, Farhan Mumtaz, Dinesh Reddy Alla, Deva Prasaad Neelakandan, Jeffrey D. Smith, Ronald J. O'Malley, Rex Gerald, Jie Huang

PSMRC Faculty Research

This study demonstrates the use of fiber Bragg grating (FBG) sensors for distributed temperature and strain monitoring in steelmaking and foundry applications. Integrated into inexpensive optical fibers, FBGs offer accurate and real-time remote sensing, detecting shifts in wavelength due to temperature (up to 1,800 °C), strain, or structural wear and tear. Furthermore, the intrinsic features of FBG sensors: compact size, immunity to electromagnetic interference and corrosion, robustness to vibration, ease of integration into existing composite structures, and non-intrusive measurement capacity in harsh environments make them ideal for steelmaking. FBGs optimize production, ensure quality, and enhance safety within the steel industry.

Enhanced Bottom Anode Monitoring In Dc Electric Arc Furnaces Using Fiber Optic Sensors, Yeshwanth Reddy Mekala, Rony Kumer Saha, Ogbole Collins Inalegwu, Muhammad Roman, Farhan Mumtaz, Rex Gerald, Jeffrey D. Smith, Jie Huang, Ronald J. O'Malley

PSMRC Faculty Research

A pin style bottom anode employs conductive steel rods that serve as the pathway for the high electrical power through rammed refractory at the bottom of a DC Electric Arc Furnace (EAF). Anode wear during operation is important to monitor, as anode replacement is expensive and impacts EAF productivity. Liquid steel penetration into the un-sintered refractory layer can result from rapid electrical power ramp-up, dips in furnace temperature, or operating the anode for too long between EAF campaigns. In extreme cases, the liquid steel may penetrate the bottom of the furnace when anode wear progresses too close to the bottom …