Materials Science and Engineering Commons^™

Microstructure, Mechanical Properties And Oxidation Behavior Of Refractory Multi-Principal Element Alloys By Laser Remelting And Conventional Manufacturing, Visharad Jalan, Seth Crawford, Sung Heng Wu, Frank Liou, Haiming Wen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Refractory multi-principal element alloys (RMPEAs), HfNbTaTiZr, (HfNbTaTiZr)9Cr, and (HfNbTaTiZr)9Al, were manufactured using vacuum arc melting followed by laser remelting to mimic additive manufacturing. the microhardness of the as-cast HfNbTaTiZr, (HfNbTaTiZr)9Cr, and (HfNbTaTiZr)9Al samples after arc melting was measured as 6.20, 7.63, and 6.89 Gpa, respectively. after laser remelting and re-solidification, the hardness increased by ~ 30% for each composition; the hardest was (HfNbTaTiZr)9Cr measured at 9.60 GPa, while the softest was HfNbTaTiZr with a hardness of 8.42 GPa, which was still harder compared to all the other samples. the addition of Al and Cr led to enhanced oxidation resistance for …

Cfrp Delamination Density Propagation Analysis By Magnetostriction Theory, Brandon Eugene Williams

All Dissertations

While Carbon Fiber Reinforced Polymers (CFRPs) have exceptional mechanical properties concerning their overall weight, their failure profile in demanding high-stress environments raises reliability concerns in structural applications. Two crucial limiting factors in CFRP reliability are low-strain material degradation and low fracture toughness. Due to CFRP’s low strain degradation characteristics, a wide variety of interlaminar damage can be sustained without any appreciable change to the physical structure itself. This damage suffered by the energy transfer from high- stress levels appears in the form of microporosity, crazes, microcracks, and delamination in the matrix material before any severe laminate damage is observed. This …

Data-Driven Multiscale Modeling Of Dye Aggregates In Dna For Excitonic Applications, Austin Biaggne

Boise State University Theses and Dissertations

In this dissertation, a data-driven, multi-scale approach was implemented to study the structural, electronic, and dynamical behavior of dye monomers and aggregates for excitonic applications. The excitonic behavior of dye aggregates depends on both the constituent monomer properties as well as the relative dye orientations that make up the aggregate. Dye monomer properties can be augmented with substituents, but with a wide range of substituent types, ideal dye derivatives should be identified. To control the aggregation of dyes, DNA can be used as a scaffold, however, the ways in which dyes interact with each other and with DNA is not …

Investigating The Influence Of Surface Finishing Methods On Corrosion Of Additively Manufactured Ss316l, Joshua R. Fadeley

Boise State University Theses and Dissertations

Additive Manufacturing (AM), namely with metal, has seen a surge in growth and interest over recent years. A wide array of industries is developing new products to take advantage of this budding technology. In order to enable adoption of this technology, understanding of the differences of AM versus traditional manufacturing on the resultant materials properties of printed components is important. The work done for this study fell into two separate categories of work.

The first effort of this work involved the installation, certification, and operation of the first laser powder bed fusion (LPBF) printer at the Center for Advanced Energy …

Advancing Additive Manufacturing For Biomedical Applications: Antimicrobial And X-Ray Absorptive Composite Filaments For Fused Filament Fabrication, John M. Arnold Jr

LSU New Orleans Theses and Dissertations

The objective of this research was to investigate the use of nano- and microparticle amendments for the creation of Poly-lactic Acid composite materials for use in biomedical applications using the Fused Filament Fabrication process of Additive Manufacturing. Composites were created with the goal of imparting the useful properties of antimicrobial activity and x-ray absorption to the material. In addition to testing the efficacy of the particle amendments in achieving the desired properties, the thermal and mechanical properties of the composite materials were tested to ensure that the composites would be compatible with the Fused Filament Fabrication process and would produce …

Exploring The Potential Of Tesla Valve For Filtering And Sorting Microscale Active Swimmers: A Computational Study, Ariel Rogers, Zhiyao He, Yong Wang

Physics Faculty Publications and Presentations

It is well-known that a Tesla valve allows fluids to flow unidirectionally without moving parts; however, how Tesla valves interact with active matters and the potential applications of Tesla valves in biology remain largely unexplored. Here, we present a computational study on the potential use of Tesla valves for filtering and sorting microscale active swimmers such as bacteria. We investigated the behavior of microscale swimmers passing through the Tesla valve at different linear and angular velocities using numerical simulations and quantified the diodicity of the Tesla valve for active swimmers. Our results demonstrate that the Tesla valve can effectively filter …

The Shape Modulation Of Laser-Induced Nanowelded Microstructures Using Two Colors, Ariel Rogers, Isabelle Niyonshuti, Jun Ou, Diksha Shrestha, Deborah Okyere, Jingyi Chen, Yong Wang

Physics Faculty Publications and Presentations

The light-based nanowelding of metallic nanoparticles is of particular interest because it provides convenient and controlled means for the conversion of nanoparticles into microstructures and the fabrication of nanodevices. In this study, we investigated the wavelength dependence of laser-induced nanowelded shapes of silver nanoparticles (AgNPs). We observed that the nanowelded microstructures illuminated with only a 405 nm laser were more branched than those formed via illumination using both the 405 nm and 532 nm lasers. We quantified this observation by two compactness descriptors and examined the dependence of the power of the 532 nm laser. More importantly, to understand the …

Structural Performance And Resiliency Of Reinforced Concrete Bridge Pier Columns, Multi-Column Piers, And Bridge Systems Subjected To Multiple Hazards – Fire, Collision, And Air Blast, Qusai Abdulkarim Alomari

Dissertations and Doctoral Documents, University of Nebraska-Lincoln, 2023–

Given their close proximity to traffic and improper employment of protective systems, bridges and bridge piers are vulnerable to multi-hazard events triggered by vehicle collisions coupled with correlated and cascading events, such as explosions and fires. Despite recent catastrophic incidents that have highlighted the profound consequences of these extreme demands, including substantial damage, adverse economic impact, and loss of life, there has been a notable lack of research investigating the performance of bridges and bridge structural components under the aforementioned multi-hazards. Furthermore, current bridge design codes do not address these events assuming that, after these destructive events, replacement of the …

Molecular Control Of Triplet-Pair Spin Polarization And Its Optoelectronic Magnetic Resonance Probes, Obadiah G. Reid, Justin C. Johnson, Joel D. Eaves, Niels H. Damrauer, John E. Anthony

Chemical and Materials Engineering Faculty Publications

Preparing and manipulating pure magnetic states in molecular systems are the key initial requirements for harnessing the power of synthetic chemistry to drive practical quantum sensing and computing technologies. One route for achieving the requisite higher spin states in organic systems exploits the phenomenon of singlet fission, which produces pairs of triplet excited states from initially photoexcited singlets in molecular assemblies with multiple chromophores. The resulting spin states are characterized by total spin (quintet, triplet, or singlet) and its projection onto a specified molecular or magnetic field axis. These excited states are typically highly polarized but exhibit an impure spin …

Analyzing The Effects Of Ultrafast Laser Processing On Mechanical Properties Of 3d-Printed Pla Parts, Darshan Pramodbhai Yadav

Theses and Dissertations

Recent advances in additive manufacturing technologies have already led to wide-scale adoption of 3D-printed parts in various industries. The expansion in choice of materials that can be processed, particularly using Fused Deposition Modeling (FDM), and the steady advancements in dimensional accuracy control have extended the range of applications far beyond rapid prototyping. However, additive manufacturing still has considerable limitations compared to traditional and subtractive manufacturing processes. This work addresses limitations associated with the as-deposited surface roughness of 3D-printed parts. The effects of roughness-induced stress concentrations were studied on ultimate tensile strength and fatigue life. The samples were manufactured using a …

Design And Characterization Of A Novel Eef2k Degrader With Potent Therapeutic Efficacy Against Triple-Negative Breast Cancer, Changxin Zhong, Rongfeng Zhu, Ting Jiang, Sheng Tian, Xiaobao Zhao, Xiaoya Wan, Shilong Jiang, Zonglin Chen, Rong Gong, Linhao He, Jin-Ming Yang, Na Ye, Yan Cheng

Markey Cancer Center Faculty Publications

Dysregulated eEF2K expression is implicated in the pathogenesis of many human cancers, including triple-negative breast cancer (TNBC), making it a plausible therapeutic target. However, specific eEF2K inhibitors with potent anti-cancer activity have not been available so far. Targeted protein degradation has emerged as a new strategy for drug discovery. In this study, a novel small molecule chemical is designed and synthesized, named as compound C1, which shows potent activity in degrading eEF2K. C1 selectively binds to F8, L10, R144, C146, E229, and Y236 of the eEF2K protein and promotes its proteasomal degradation by increasing the interaction between eEF2K and the …

Material World, Nicole Weldy

All Theses

My thesis, Material World, delves into the use of the crochet unit as a construction technique for building forms. Through this, I aim to organize different materials in a way that responds to the challenges posed by the physical world. My artistic process is centered around honoring the inherent qualities of thread and uses these qualities to create form, lightness, and linearity. At the same time, I remain receptive to transformative processes such as combining three-dimensional (3D) printed lines and lace stiffener to push the boundaries of what thread can do. By combining manual craftsmanship with technology materialized as …

Role Of Mechanical Signaling In Bone Tissue, Scott Aaron Birks

Boise State University Theses and Dissertations

As the global population ages and life expectancy continues to rise, osteoporosis continues to be a growing worldwide health concern. The International Osteoporosis Foundation reports 1 in 3 women over the age of 50 years and 1 in 5 men worldwide will experience osteoporotic fractures in their lifetime, costing between 5 and 6.5 trillion USD annually in Canada, Europe, and the United States alone. The need for preventative measures to reduce age-related bone loss is clear, not only to improve quality of life for countless individuals but also to relieve the economic burden this condition imposes.

Exercise is a proven …

Synergistic Strategies In Sinter-Based Material Extrusion (Mex) 3d Printing Of Copper: Process Development, Product Design, Predictive Maps And Models., Kameswara Pavan Kumar Ajjarapu

Electronic Theses and Dissertations

3D printing pure copper with high electrical conductivity and exceptional density has long been challenging. While laser-based additive manufacturing technologies suffered due to copper's highly reflective nature towards laser beams, parts printed via binder-assisted technologies failed to reach over 90% IACS (International Annealed Copper Standard), electrical conductivity. Although promising techniques such as binder jetting, filament, and pellet-based 3D printing that can print copper exist, they however still face difficulties in achieving both high sintered densities and electrical conductivity values. This is due to a lack of comprehensive understanding of property evolution from green to sintered states and the strategies that …

Additive Manufacturing Of Microelectronic Devices For Extreme Environments, Nicholas Mckibben

Boise State University Theses and Dissertations

This work encompasses a comprehensive exploration of advanced manufacturing techniques for fabricating microelectronic devices compatible with extreme environments. The research integrates the fields of chemistry, nanomaterials, and additive manufacturing to achieve remarkable progress in sensor development, with a particular emphasis on aerosol jet printing (AJP), surface acoustic wave (SAW) devices, patterned graphene growth, and surface functionalization. The investigation begins with the AJP process development of a commercial silver nanoparticle ink, culminating in the fabrication of a piezoelectric SAW transducer that was prototyped as a high-temperature thermometer, showing excellent linearity when validated to 200°C. Next, the investigation continued with the development …

Novel Sensors And Measurement Techniques For Thermal Properties In Extreme Environments, Katelyn Wada

Boise State University Theses and Dissertations

Advancements in thermal properties analysis is crucial for improvement of existing and next generation reactors, space exploration, and environmental safety. Extreme environments pose a great hurdle for instrumentation to measure real time thermal properties due to the extreme temperatures, high radiation, and variable electromagnetic environments. Nevertheless, measurement systems are tremendously important for the design, P.E.rformance, and safety considerations of nuclear fuels, space crafts, and deep sea/deep earth drilling. Thermal properties may change significantly in these environments creating challenging problems for temperature and thermal conductivity measurement systems. A recent focus has surrounded improvements in such systems for accurate determination of temperature …

Engineered Biomass-Derived Carbon Adsorbents For Targeted Contaminant Remediation From Aqueous Environments, Suraj Venkat Pochampally

UNLV Theses, Dissertations, Professional Papers, and Capstones

Porous carbon adsorbents like biochar (BC) are produced from waste biomasses like wood chips, animal litter, nut shells, dried grass, etc. to be used in a multitude of applications like gas capture, soil amendment, water treatment, electrode materials, etc. In water treatment, carbon-based adsorbents have been mainly used to physically or chemically adsorb contaminants depending on the adsorption mechanism. However, BCs in their raw state do not have the capability of absorbing high amounts of contaminants and need to be activated/ modified for the pore network to broaden and adsorb the contaminants with better efficiency.

The scope of this dissertation …

Sustainable Diamond-Like Carbon Fabricated Gravure Cylinders For Printing Fine Lines Of Electrodes And Graphic Structures, Chandramohan Seetharamiah Srinivasaraju

Dissertations

The main objective of this work is to evaluate the potential of Diamond-Like Carbon (DLC) as an alternative to chrome for use on gravure cylinders. DLC coatings consist of carbon atoms, arranged into a diamond-like structure that closely resembles that of natural diamond. In contrast to chrome, DLC is environmentally friendly. The focus of the study is to determine the viability of DLC as a substitute material for chrome to be used on gravure cylinders by determining key material properties and evaluating printing performance.

In the first research paper, four DLC variants (Standard DLC, A-DLC, S-DLC, and Organic Silica) and …

3d Printed Microdialysis-Based Microsampling Probes, Patrick Pysz

Graduate Theses and Dissertations

This work will show the development of a fully 3D printed device platform in which a complex microsampling probe geometry is fabricated in a simple two-step process. This process includes the combination of 2-photon polymerization (2PP) and masked-stereolithography (MSLA). The cutting edge neurotechnology needed to monitor brain internal communication and will require multiple sensing modalities including temperature, pressure, electrophysiological, and optogenetics. Microsampling is an integrally important function for any future biosensing device platform as it allows for chemical delivery and unparalleled specificity through offline analysis of collection samples. Stereolithography (SLA) 3D printing has emerged as a powerful fabrication method capable …

An Icfd Fluid Model Used In A Mash Tl-6 Vehicle Model, Md Zunayed Habib

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The objective of this thesis was to develop an ICFD finite element model of a partially filled deformable container suitable for impact scenarios. This model will be later incorporated into the existing TL-6 vehicle model, which is a tractor-tank trailer vehicle model. Previous finite element fluid models for the TL-6 vehicle used an elastic fluid model, which could not predict the fluid behavior correctly.

A study was conducted on the ICFD modeling and an improved ICFD model has been developed using the LS-DYNA, a finite element analysis software. Different properties and parameters of the fluid and the container were adopted …

Characterization Of Interlayer Laser Shock Peening During Fused Filament Fabrication Of Polylactic Acid (Pla), Fabien Denise

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

The field of additive manufacturing (AM) has gained a significant amount of popularity due to the increasing need for more sustainable manufacturing techniques and the adaptive development of complex product geometries. The problem is that AM parts routinely exhibit flaws or weaknesses that affect functionality or performance. Over the years, surface treatments have been developed to compensate certain flaws or weaknesses in manufactured products. Combining surface treatments with the modularity of additive manufacturing could lead to more adaptable and creative improvements of product functions in the future. The current work evaluates the feasibility of pursuing a new research axis in …

Experimental Analysis Of Nonlinear Wave Propagation In Bistable Mechanical Metamaterials With A Defect, Samuel R. Harre

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Mechanical metamaterials built up of compliant units can support the propagation of linear and nonlinear waves. A popular architecture consists of a one-dimensional chain of bistable elements connected by linear springs. This type of chain can support nonlinear transition waves that switch each element from one stable state to the other as they propagate along the chain. One way to manipulate the propagation of such waves is via introduction of a local inhomogeneity, i.e., a defect in the otherwise periodic chain. Recent analytical and numerical work has shown that based on its initial velocity, a transition wave may be reflected, …

Study On Effect Of 3d Printing Parameters On Surface Roughness And Tensile Strength Using Analysis Of Variance, Faqih Fadillah, Heru Suryanto, Suprayitno Suprayitno

Journal of Mechanical Engineering Science and Technology (JMEST)

Fused deposition modeling of 3D printing is the process of making workpieces or parts by adding filaments to each layer. Some indicators of a high-quality product of 3D printing are the precisions dimensions, the surface roughness, and tensile strength. This research aims to find the parameters most affecting surface roughness and tensile strength. The research design used an experimental method with input parameters: (1) print speed (15-35 mm/s), (2) print temperature (200-210C), (3) layer height (0.1 – 0.3 mm), (4) infill line directions (0-90), and dependent variables were surface roughness and tensile strength. The data distribution used the L9 orthogonal …

Mechanical Characterization Of Naoh-Treated Agel Fiber-Cotton Composites, I Gusti Ngurah Nitya Santhiarsa, I Gusti Bagus Wijaya Kusuma, I Gede Artha Negara

Journal of Mechanical Engineering Science and Technology (JMEST)

Composites comprising two or more distinct materials are fabricated to enhance the mechanical properties of the constituent materials. A common approach for generating composites is vacuum infusion. This technique enables the infusion of two materials utilizing a vacuum. In the field of composite science, textile composites have emerged as an important new development. Agel rope, derived from twisting agel fibers, exhibits inferior bending strength and elongation compared to ropes fabricated from synthetic fibers. Moreover, agel rope is susceptible to bacterial decay. This study aims to characterize the mechanical properties of textile composites comprising woven agel rope subjected to NaOH treatment. …

Heat Conduction In Cylindrical Coordinates With Time-Varying Conduction Coefficients: A Practical Engineering Approach, Lulut Alfaris, Ruben Cornelius Siagian, Aldi Cahya Muhammad, Ukta Indra Nyuswantoro, Budiman Nasution

Journal of Mechanical Engineering Science and Technology (JMEST)

This research aims to develop a mathematical method for expressing the Laplace operator in cylindrical coordinates and applying it to solve heat conduction equations in various scenarios. The method commences by transforming Cartesian coordinates into cylindrical coordinates and identifying the necessary substitutions. The result is the expression of the Laplace operator in cylindrical coordinates, which is subsequently employed to address heat conduction equations within cylindrical coordinates. Various cases encompassing different initial and boundary conditions, as well as variations in the conduction coefficient over time, are meticulously considered. In each instance, precise mathematical solutions are determined and subjected to thorough analysis. …

Numerical Study On Resistance Of Stepped Planing Hull, Fajri Ashfi Rayhan, Andika Masrul, Arya Khairullah Akbar, Bima Anugerah Putra

Journal of Mechanical Engineering Science and Technology (JMEST)

A stepped planing hull, also known as a step hull, is a hull modification that reduces the wetted surface area. Although this type of hull has proven effective in several ships, it is still rarely used. The step hull possesses numerous advantages that make it ideal for activities involving small and fast boats. However, regrettably, its full potential remains untapped at present. The purpose of this study was to identify the effect of variations in the angle of the step hull on resistance or drag. The study utilized the CFD method, and three hull configuration models were used at each …

Analyzing Transition Metallic Catalytic Converter Impact On Four-Stroke Motorcycle Fuel Consumption, Sudirman Rizki Ariyanto, Ata Syifa’ Nugraha, Wahyu Robby Cahyadi, Yelma Dianastiti, Muhammad Yandi Pratama

Journal of Mechanical Engineering Science and Technology (JMEST)

Increased exhaust emissions from motor vehicles have become a major concern in efforts to reduce air pollution. One developed solution is the use of transition metallic catalytic converter (TMCC) technology in vehicle exhaust systems. This study aims to compare the fuel consumption efficiency of three types of exhaust systems, namely standard exhaust without a catalyst (STD WC), the standard exhaust with Original Equipment Manufacturer catalyst (STD OEM), and an exhaust system equipped with a Copper-Coated Chrome Metallic Catalytic Converter (TMCC CuCr). The data analysis method employed a quantitative approach by collecting fuel consumption data at each rpm and analyzing the …

Effect Of The Homogenization Process On Titanium Oxide-Reinforced Nanocellulose Composite Membranes, Taufiq Mahsuli, Aisyah Larasati, Aminnudin Aminnudin, Jibril Maulana

Journal of Mechanical Engineering Science and Technology (JMEST)

Indonesian pineapple production can reach 200 tons per day; however, pineapples generate a significant amount of waste. Pineapple peel waste can be used to make membranes. Composite membranes containing TiO2 have dense properties, low porosity, and increase the mechanical strength of the cellulose sheet. This research uses various ultrasonic homogenizers to homogenize the distribution of nanocellulose and TiO2 (50% and 100% power with 30, 60, and 90 minutes). The casting method is used to shape the membrane. The SEM test shows that the higher the power used and the longer the sonication time, the less agglomeration of about 1.63%/ cm2 …

Effect Of Heating Temperature, Holding Time And Stabilization Temperature On The Al-Foam Properties, Dewi Puspitasari, Poppy Puspitasari, Mazli Mustapha, Turnad Lenggo Ginta

Journal of Mechanical Engineering Science and Technology (JMEST)

The interest in metallic foam is increasing since their cellular structures have a unique combination of properties such as high stiffness, low density, lightweight, high specific strength, and thermal insulation. Commonly, the performance of metallic foam can be improved by the heat treatment process. However, the previous heat treatment methods still present the brittle crack path and the research on heat treatments of the metal foam properties is very limited. In this study, individual parameters in stress relieving treatment that contribute to Al-Foam properties were investigated. The stress-relieving process of the samples was performed using a vacuum furnace. The composition …

Vertical Shaft Kinetic Turbine Performance Using A Cup-Shape Blade, Kennie A. Lempoy, Nita C. V. Monintja, Arwanto M. A. Lakat

Journal of Mechanical Engineering Science and Technology (JMEST)

The abundant availability of alternative energy sources forms the fundamental foundation for rural energy development. In particular, renewable energy sources are indispensable in rural areas due to their ecofriendly nature and widespread accessibility, which helps preserve the environment by avoiding pollution. Indonesia, a country blessed with vast water resources, especially its rivers, holds enormous potential for harnessing kinetic energy derived from fast-flowing river waters. Effective utilization of this kinetic energy has the potential to address energy shortages in the country. In this context, there is a pressing need to enhance the efficiency of kinetic turbines designed to function as electricity …