Materials Science and Engineering Commons^™

The Thermophysical Properties Of Tco2, Hong Zhong, Jason Lonergan, John S. Mccloy, Scott P. Beckman

Materials Science and Engineering Faculty Research & Creative Works

Technetium-99 Is A Highly Radioactive Isotope With A Long Half-Life That Is Common In Nuclear Waste. It Volatizes At A Low Temperature, Which Poses A Significant Challenge To The Clean-Up And Containment Processes. Due To Difficulties In Purifying Technetium Compounds, Their Thermophysical Properties Have Not Been Measured Or Calculated. Here, First Principle Methods Are Used Along With The Quasi Quasi-Harmonic Harmonic Approximation To Compute The Debye Temperature, Volumetric Thermal Expansion Coefficient, Bulk Modulus, And Heat Capacity Of Rutile TcO2 For Temperatures Ranging From 0 To 1500 K And Applied Pressures Ranging From 0 To 255 GPa. The Computed Atomic Structures …

Dielectric Properties Of Polycrystalline And Single-Crystal Magnesium Oxide At High Temperatures, Alan Devoe, Hung Trinh, Fatih Dogan

Materials Science and Engineering Faculty Research & Creative Works

The electrical properties of high-purity magnesium oxide (MgO) samples sintered between 1500 and 1650°C were investigated up to 800°C. Dielectric constant, loss tangent and electrical conductivity were measured between 25 and 800°C. Optimum electrical properties were obtained for the sample sintered at 1600°C. The impurities in polycrystalline and single crystal MgO were discussed to understand their effect on electrical properties and the role of grain boundaries. Higher dielectric losses of polycrystalline samples as compared to the single crystal MgO were attributed to the presence of grain boundaries. MgO could be a useful dielectric material for capacitor applications up to 600°C.

Influence Of Environmental Barrier Coatings On The Overall Effectiveness Of A Film Cooled Ceramic Matrix Composite Plate, Shane P. Lindsay

Theses and Dissertations

Silicon carbide ceramic matrix composites, a promising new potential upgrade over the conventional metals currently used for jet engine turbine blades, have a propensity to oxidize in a combustion environment. Engine manufacturers often apply environmental barrier coatings to prevent the composites from oxidizing. What is unclear, however, is how environmental barrier coatings effect underlying composite temperatures. This research examined the coatings’ effects by first characterizing the influence of environmental barrier coatings on the underlying temperature of a protected ceramic, then evaluating the significance of lateral conduction for cooling a coated ceramic, and finally comparing cooling results for coated and uncoated …

Toward Smart And Sustainable Cement Manufacturing Process: Analysis And Optimization Of Cement Clinker Quality Using Thermodynamic And Data-Informed Approaches, Jardel P. Gonçalves, Taihao Han, Gaurav Sant, Narayanan Neithalath, Jie Huang, Aditya Kumar

Electrical and Computer Engineering Faculty Research & Creative Works

Cement manufacturing is widely recognized for its harmful impacts on the natural environment. In recent years, efforts have been made to improve the sustainability of cement manufacturing through the use of renewable energy, the capture of CO₂ emissions, and partial replacement of cement with supplementary cementitious materials. To further enhance sustainability, optimizing the cement manufacturing process is essential. This can be achieved through the prediction and optimization of clinker phases in relation to chemical compositions of raw materials and manufacturing conditions. Cement clinkers are produced by heating raw materials in kilns, where both raw material compositions and processing conditions …

Local Strain Quantification Of A Porous Carbon Fiber Network Material, Robert N Quammen, Paul F. Rottmann

Chemical and Materials Engineering Faculty Publications

While porous materials’ wide range of attractive functional properties have led to their development for a variety of applications, their intrinsically stochastic microstructures prevent straightforward approaches to predicting their mechanical behavior. This is attributed to the mechanisms that govern the macroscale behavior of these materials operating on multiple microstructure-specific length scales spanning several orders of magnitude. The goal of this work was to experimentally observe these operative deformation mechanisms to better improve the development of mechanism-informed models that more accurately predict the behavior of these materials. In this study compression tests were conducted on a porous carbon fiber network material. …

The Janssen Effect And The Chini Ordinary Differential Equation, Adam Rogers, George Dyck, Jitendra Paliwal, Kurt Hildebrand, Michael D. Montross, Aaron P. Turner

Chemical and Materials Engineering Faculty Publications

The Janssen effect describes the increase in pressure with depth in granular materials. However, the original Janssen formulation treats the density as constant. In this work, we examine parametric density models that depend on both pressure and moisture content and allow for temperature dependence to be easily included. We focus on physically-motivated empirical models that are built on power-law terms. These power-law terms correspond to thermodynamic equations of state, such as the ideal gas law, and polytropic processes. When coupled with the Janssen ordinary differential equation (ODE), these power-law models have the form of a Chini ODE. We study the …

Protocol For Modeling And Simulating Lithiation-Induced Stress In Largely Deformed Spherical Nanoparticles Using Comsol, Yong Li, Yungpeng Guo, Yunhao Wu, Yin Rao, Kai Zhang, Dashun Liu, Fuqian Yang

Chemical and Materials Engineering Faculty Publications

Here, we present a finite element method-based scheme for solving coupled par- tial differential equations (PDEs) for the analysis of lithiation-induced stress in largely deformed spherical nanoparticles via the PDE module in COMSOL. We describe steps for software installation and setting PDEs, initial/boundary condi- tions, and mesh parameters. We then detail procedures for dividing the mesh and analyzing lithium trapping during electrochemical cycling. This protocol can also be extended to analyze a wide range of problems involving diffusion-induced stress. For complete details on the use and execution of this protocol, please refer to Li et al.

Spontaneous Alignment Of Myotubes Through Myogenic Progenitor Cell Migration, Lauren E. Mehanna, Adrianna R. Osborne, Charlotte A. Peterson, Brad J. Berron

Chemical and Materials Engineering Faculty Publications

In large-volume muscle injuries, widespread damage to muscle fibers and the surrounding connective tissue prevents myogenic progenitor cells (MPCs) from initiating repair. There is a clinical need to rapidly fabricate large muscle tissue constructs for integration at the site of large volume muscle injuries. Most strategies for myotube alignment require microfabricated structures or prolonged orientation times. We utilize the MPC’s natural propensity to close gaps across an injury site to guide alignment on collagen I. When MPCs are exposed to an open boundary free of cells, they migrate unidirectionally into the cell-free region and align perpendicular to the original boundary …

Spectroscopic Characterization Of Trivalent Holmium In Liyf4 And Bay2F8 Crystals, Vivian R. Hedberg

Theses and Dissertations

Yttrium-fluoride crystals doped with trivalent holmium are promising laser gain media for mid-infrared laser systems. To accurately model laser systems, a complete optical characterization of the laser gain medium is required. The key modeling parameters were obtained by a spectroscopic investigation of Ho³⁺ in LiYF₄ and BaY₂F₈ crystal hosts. Several important mid-infrared laser transitions were characterized at nominal Ho³⁺ ion concentrations of 10-30 at.%. Polarized emission cross-sections were determined from the fluorescence spectra using the Füchtbauer-Ladenburg method. Polarized absorption cross-sections were obtained using the Integral Reciprocity method. The upper-state lifetimes were measured at room …

Spatiotemporal Dispersion Compensation For A 200-Thz Noncollinear Optical Parametric Amplifier, William P. Carbery, Laurie A. Bizimana, Matthew S. Barclay, Nicholas D. Wright, Paul H. Davis, William B. Knowlton, Ryan D. Pensack, Paul C. Arpin, Daniel B. Turner

Materials Science and Engineering Faculty Publications and Presentations

A noncollinear optical parametric amplifier (NOPA) can produce few-cycle femtosecond laser pulses that are ideally suited for time-resolved optical spectroscopy measurements. However, the nonlinear-optical process giving rise to ultrabroadband pulses is susceptible to spatiotemporal dispersion problems. Here, we detail refinements, including chirped-pulse amplification (CPA) and pulse-front matching (PFM), that minimize spatiotemporal dispersion and thereby improve the properties of ultrabroadband pulses produced by a NOPA. The description includes a rationale behind the choices of optical and optomechanical components, as well as assessment protocols. We demonstrate these techniques using a 1 kHz, second-harmonic Ti:sapphire pump configuration, which produces ∼5-fs duration pulses that …

Characterization Of An Omega Type Bi-Anisotropic Material, Moriel Gindi

Theses and Dissertations

A theory is presented for the extraction of the complete set of material parameters for a bi-anisotropic sample consisting of conductive omega-type particles governed by the mm21′ point-group symmetry. A rectangular-to-square wave-guide can be used to obtain the required measurements by allowing three distinct orientations of the material. The focus of this work is to develop the appropriate theory detailing the derivation of how the material parameters are extracted from the measurements in an analytical methodology that is similar in manner to the well-known Nicolson-Ross-Weir (NRW) algorithm.

A Bayesian Approach For Lifetime Modeling And Prediction With Multi-Type Group-Shared Missing Covariates, Hao Zeng, Xuxue Sun, Kuo Wang, Yuxin Wen, Wujun Si, Mingyang Li

Engineering Faculty Articles and Research

In the field of reliability engineering, covariate information shared among product units within a specific group (e.g., a manufacturing batch, an operating region), such as operating conditions and design settings, exerts substantial influence on product lifetime prediction. The covariates shared within each group may be missing due to sensing limitations and data privacy issues. The missing covariates shared within the same group commonly encompass a variety of attribute types, such as discrete types, continuous types, or mixed types. Existing studies have mainly considered single-type missing covariates at the individual level, and they have failed to thoroughly investigate the influence of …

Thermal Insulation And Fire Protection Plaster For Frp System Incorporating Aerogel Nanoparticles And Phyllosilicates, Athnasious Ghaly

Theses and Dissertations

For more than two decades, new innovative materials have been introduced to the market such as nano materials that can be utilized for their high performance in different aspects of the construction industry. Structural repair and strengthening is one of the most demanding fields in the construction industry for innovative and high-performance materials due to its specialty. Time, quality, economy, and sustainability are the main factors that control this field, and for that, new systems keep being introduced to the market to reduce the time of repair and enhance its efficiency. Fiber Reinforced Polymers (FRP) Systems are the most advanced …

Applicability Of Using Bio-Receptive Concrete For Building Facades In Egypt, Gina Roupheil

Theses and Dissertations

The significant increase in carbon dioxide emissions caused by the construction industry is detrimental to our planet. This is rapidly increasing with the urbanization of cities that is gradually taking its toll on the available green spaces, which help in balancing such emissions. Recently, researchers have been trying to make use of bio-receptivity to create biomaterial systems that could be spread on building envelopes and support the growth of small plant species and microorganisms to establish on. Out of those materials, comes the concrete as a promising material for bio-colonization.

Within this context, this study aims at investigating the applicability …

The Behavior Of ½⟨111⟩ Screw Dislocations In W–Mo Alloys Analyzed Through Atomistic Simulations, Lucas A. Heaton, Kevin Chu, Adib J. Samin

Faculty Publications

Analyzing plastic flow in refractory alloys is relevant to many different commercial and technological applications. In this study, screw dislocation statics and dynamics were studied for various compositions of the body-centered cubic binary alloy tungsten–molybdenum (W–Mo). The core structure did not appear to change for different alloy compositions, consistent with the literature. The pure tungsten and pure molybdenum samples had the lowest plastic flow, while the highest dislocation velocities were observed for equiatomic, W_0.5Mo_0.5 alloys. In general, dislocation velocities were found to largely align with a well-established dislocation mobility phenomenological model supporting two discrete dislocation mobility regimes, …

Automated Workflow For Redox Potentials And Acidity Constants Calculations From Machine Learning Molecular Dynamics, Feng Wang, Jun Cheng

Journal of Electrochemistry

Redox potentials and acidity constants are key properties for evaluating the performance of energy materials. To achieve computational design of new generation of energy materials with higher performances, computing redox potentials and acidity constants with computational chemistry have attracted lots of attention. However, many works are done by using implicit solvation models, which is difficult to be applied to complex solvation environments due to hard parameterization. Recently, ab initio molecular dynamics (AIMD) has been applied to investigate real electrolytes with complex solvation. Furthermore, AIMD based free energy calculation methods have been established to calculate these physical chemical properties accurately. However, …

Assessing Adoption Barriers Of Sustainable Packaging In Egypt, Carol Ramses Morgan

Theses and Dissertations

Sustainable packaging has become an essential part of business decisions and corporate directions. With the rise of environmental damages due to improper waste management and unsustainable practices, businesses have a major responsibility to analyze their products’ life cycles and redesign them with sustainability in mind. Applying sustainable packaging could save companies large amounts of resources, therefore cutting costs, while also achieving the legal and social duty as a corporation towards society and the environment. Many developing countries, with specific focus on Egypt, have recently focused on legislative and corporate decisions in order to encourage more sustainable practices. Egypt’s new Waste …

Joint Time-Frequency Analysis: Taking Charge Penetration Depth And Current Spatial Distribution In The Single Pore As An Example, Nan Wang, Qiu-An Huang, Wei-Heng Li, Yu-Xuan Bai, Jiu-Jun Zhang

Journal of Electrochemistry

In recent years, joint time-frequency analysis has once again become a research hotspot. Supercapacitors have high power density and long service life, however, in order to balance between power density and energy density, two key factors need to be considered: (i) the specific surface area of the porous matrix; (ii) the electrolyte accessibility to the intra-pore space of porous carbon matrix. Electrochemical impedance spectra are extensively used to investigate charge penetration ratio and charge storage mechanism in the porous electrode for capacitance energy storage. Furthermore, similar results could be obtained by different methods such as stable-state analysis in the frequency …

A Study On High-Frequency Bending Fatigue, Microhardness, Tensile Strength, And Microstructure Of Parts Made Using Atomic Diffusion Additive Manufacturing (Adam) And Additive Friction Stir Deposition (Afsd), Hamed Ghadimi

LSU Doctoral Dissertations

This dissertation reports the findings of several studies on the mechanical and microstructural properties of parts made using atomic diffusion additive manufacturing (ADAM) and additive friction stir deposition (AFSD). The design of a small-sized bending-fatigue test specimen for an ultrasonic fatigue testing system is reported in Chapter 1. The design was optimized based on the finite element analysis and analytical solution. The stress–life (S–N) curve is obtained for Inconel alloy 718. Chapter 2 presents the findings of ultrasonic bending-fatigue and tensile tests carried out on the ADAM test specimens. The S-N curves were created in the very high-cycle fatigue regime. …

Formulation And Aerosol Jet Printing Of Nickel Nanoparticle Ink For High-Temperature Microelectronic Applications And Patterned Graphene Growth, Nicholas Mckibben, Michael Curtis, Olivia Maryon, Mone’T Sawyer, Maryna Lazouskaya, Josh Eixenberger, Zhangxian Deng, David Estrada

Materials Science and Engineering Faculty Publications and Presentations

Aerosol jet printing (AJP) is an advanced manufacturing technique for directly writing nanoparticle inks onto target substrates. It is an emerging reliable, efficient, and environmentally friendly fabrication route for thin film electronics and advanced semiconductor packaging. This fabrication technique is highly regarded for its rapid prototyping, the flexibility of design, and fine feature resolution. Nickel is an attractive high-temperature packaging material due to its electrical conductivity, magnetism, and corrosion resistance. In this work, we synthesized nickel nanoparticles and formulated an AJP ink, which was printed on various material surfaces. Thermal sintering experiments were performed on the samples to explore the …

Fly Ash Coated With Alumina Sol For Improving Strength And Thermal Insulation Of Mullite Porous Ceramics, Minghui Li, Peilin Li, Qingqing Gao, Saisai Li, Ruoyu Chen, Haiming Wen, Canhua Li

Materials Science and Engineering Faculty Research & Creative Works

The manufacturing of mullite porous ceramics with high strength and low thermal conductivity was achieved through foam gel-casting processes using fly ash coated with alumina sol layers. This research aimed to investigate the effect of alumina sol concentration on foaming slurry rheology, as well as the influence of alumina sol coating layers on the microstructure, phase compositions and properties of the resulting mullite porous ceramics. Increasing the alumina sol concentration from 5 to 20 wt% improved both the viscosity and thixotropy of the foaming slurries while enhanced the shear thinning behavior. Porous ceramics prepared with fly ash coated with alumina …

Material Order: A Discovery Group And Shared Catalogue For Materials Collections, Mark Pompelia, Margot Mcilwain Nishimura

Faculty & Librarian Work

Material Order is an academic consortium of material sample collections for art, architecture, and design disciplines. Founded by the Graduate School of Design at Harvard University and Fleet Library at Rhode Island School of Design and since comprising several more institutions in the US, it provides a community-based approach to management and open access utilizing and developing standards and best practices. Now in its twelfth year and reaching a level of maturation, Material Order offers research and pedagogical value to current and potential members and the larger design communities.

Experimental Thermal Conductivity Studies Of Agar-Based Aqueous Suspensions With Lignin Magnetic Nanocomposites, Bishal Gautam, Saja M. Nabat Al-Ajrash, Mohammad Jahid Hasan, Abhishek Saini, Sarah J. Watzman, Esteban Ureña-Benavides, Erick S. Vasquez-Guardado

Chemical and Materials Engineering Faculty Publications

Nanoparticle additives increase the thermal conductivity of conventional heat transfer fluids at low concentrations, which leads to improved heat transfer fluids and processes. This study investigates lignin-coated magnetic nanocomposites (lignin@Fe₃O₄) as a novel bio-based magnetic nanoparticle additive to enhance the thermal conductivity of aqueous-based fluids. Kraft lignin was used to encapsulate the Fe₃O₄ nanoparticles to prevent agglomeration and oxidation of the magnetic nanoparticles. Lignin@Fe₃O₄ nanoparticles were prepared using a pH-driven co-precipitation method with a 3:1 lignin to magnetite ratio and characterized by X-ray diffraction, FT-IR, thermogravimetric analysis, and transmission electron …

Pisa Printing Microneedles With Controllable Aqueous Dissolution Kinetics, Aaron Priester, Jimmy Yeng, Yuwei Zhang, Krista Hilmas, Risheng Wang, Anthony J. Convertine

Chemistry Faculty Research & Creative Works

This study focused on the development of high-resolution polymeric structures using polymer-induced self-assembly (PISA) printing with commercially available digital light-processing (DLP) printers. Significantly, soluble solids could be 3D-printed using this methodology with controllable aqueous dissolution rates. This was achieved using a highly branched macrochain transfer agent (macro-CTA) containing multiple covalently attached CTA groups. In this work, the use of acrylamide as the self-assembling monomer in isopropyl alcohol was explored with the addition of N-(butoxymethyl)acrylamide to modulate the aqueous dissolution kinetics. PISA-printed microneedles were observed to have feature sizes as small as 27 μm, which was close to the resolution limit …

Progress In Energy: Usa–Canada Special Issue On Energy, Yun Hang Hu

Michigan Tech Publications

No abstract provided.

Degradation Of The Mechanical Properties And Hydrogen Generation In Cement Under Gamma Irradiation Assessed By Atomistic Simulation, Omar Al Najjar

Theses and Dissertations

Although understanding the effect of the gamma-ray on cement-based materials is essential for many applications, such as the concrete contaminate of nuclear reactors or the storage of radioactive waste in cement-based waste forms, such understanding is still not fully developed. The importance of having such an understanding is becoming of utmost importance, especially with calls to extend the lifetime of nuclear power plants, and also due to some recent incidents of failures of the concrete structure in the nuclear fields. In this work, the details of preparing three molecular models as a representative structure of the main binding phase of …

Understanding Roles And Evaluating Reactivity Of Fly Ashes In Calcium Aluminate Binders, Sai Akshay Ponduru, Taihao Han, Jie Huang, Narayanan Neithalath, Gaurav Sant, Aditya Kumar

Electrical and Computer Engineering Faculty Research & Creative Works

Calcium aluminate cement (CAC) is an alternative to Portland cement, valued for its superior early strength and thermal resistance. Partially replacing CAC with Fly ash (FA) can reduce carbon footprint and production costs of CAC, producing sustainable cementitious binders. This research investigates on various properties (i.e., hydration kinetics; phase assemblage evolution; compressive strength) of [CAC + FA] binders. Using 13 distinct FAs, up to 50% of CAC was substituted. The study measures hydration kinetics, compressive strength, and employs the number of constraints to estimate FA reactivity. Advanced quantitative analysis draws links between hydration kinetics and compressive strength and elucidate the …

Ion Irradiation And Examination Of Additive Friction Stir Deposited 316 Stainless Steel, Priyanka Agrawa, Ching-Heng Shiau, Aishani Sharma, Zhihan Hu, Megha Dubey, Yu Lu, Lin Shao, Ramprashad Prabhakaran, Yaqiao Wu, Rajiv S. Mishra

Materials Science and Engineering Faculty Publications and Presentations

This study explored solid-state additive friction stir deposition (AFSD) as a modular manufacturing technology, with the aim of enabling a more rapid and streamlined on-site fabrication process for large meter-scale nuclear structural components with fully dense parts. Austenitic 316 stainless steel (SS) is an excellent candidate to demonstrate AFSD, as it is a commonly-used structural material for nuclear applications. The microstructural evolution and concomitant changes in mechanical properties after 5 MeV Fe⁺⁺ ion irradiation were studied comprehensively via transmission electron microscopy and nanoindentation. AFSD-processed 316 SS led to a fine-grained and ultrafine-grained microstructure that resulted in a simultaneous increase …

Residual Optical Absorption From Native Defects In Cdsip2 Crystals, Timothy D. Gustafson, Nancy C. Giles, Elizabeth M. Scherrer, Kevin T. Zawilski, Peter G. Schunemann, Kent L. Averett, Jonathan E. Slagle, Larry E. Halliburton

Faculty Publications

CdSiP₂ crystals are used in optical parametric oscillators to produce tunable output in the mid-infrared. As expected, the performance of the OPOs is adversely affected by residual optical absorption from native defects that are unintentionally present in the crystals. Electron paramagnetic resonance (EPR) identifies these native defects. Singly ionized silicon vacancies (V^-_Si) are responsible for broad optical absorption bands peaking near 800, 1033, and 1907 nm. A fourth absorption band, peaking near 630 nm, does not involve silicon vacancies. Exposure to 1064 nm light when the temperature of the CdSiP₂ crystal is near 80K converts …

Vaccine Immunogenicity Versus Gastrointestinal Microbiome Status: Implications For Poultry Production, Chrysta N. Beck, Jiangchao Zhao, Gisela F. Erf

Poultry Science Faculty Publications and Presentations

At the turn of the 21st century, the importance of maintaining a balanced microbiome was brought to the forefront of the microbiology, immunology, and physiology research fields. Exploring the complex interactions between vaccine administration, mucosal microbiome, oral tolerance, and enteric inflammation in health and disease is challenging since environmental factors (such as diet and sanitation) have major influences on gut microbiota composition. High enteric pathogen load has been shown to contribute to dampened cell-mediated and humoral immune responses to vaccines in human case studies, either through elevated enteric inflammation or increased tolerance to environmental microbes. Although antibiotic and probiotic interventions …