Structural Engineering Commons^™

Expanding The Applicability Of Press-Brake-Formed Tub Girders Through The Extension Of The Maximum Span Length And The Evaluation Of Pier Continuity, Robert M. Tennant

Graduate Theses, Dissertations, and Problem Reports (ETD)

The Short Span Steel Bridge Alliance (SSSBA) is a group of bridge and buried soil steel structure industry leaders who provide educational information on the design and construction of short-span steel bridges in installations up to 140 feet in length. Within the SSSBA technical working group, a modular, shallow press-brake-formed tub girder (PBFTG) was developed to address the demand in the short-span steel bridge market for rapid infrastructure replacement solutions. PBFTGs consist of modular, shallow, trapezoidal boxes fabricated from cold-bent structural steel plate. A concrete deck, or other deck option, may be placed on the girder, and the modular unit …

Quantitative Bridge Inspection Ratings Using Autonomous Robotic Systems, Anil K. Agrawal

Project IM-2

Impact sounding has been recognized as an effective technique to detect delamination in concrete structures, such as concrete decks. An enormous amount of sounding data can be generated/collected by the autonomous inspection systems equipped with impactors and microphones. However, the main challenge in the practical application of this technology is the development of advanced data analysis approaches for identifying defects from impact sounding data. In this study, the empirical mode decomposition (EMD) analysis and power-spectral density (PSD) analysis are combined to extract useful features of sounding data generated by the impact hammer. It has been found that the EMD method …

Comparative Analysis Of Bridge Abutment Types, David Fell

Williams Honors College, Honors Research Projects

This project was developed to serve as a brief overview of design practices and considerations in the selection of highway bridge abutment types. This involved a review of literature in the form of reviewing national design guides and department of transportation (DOT) requirements from both US DOTs and international DOTs. The abutment types covered in this research included conventional reinforced concrete abutments with bearings, integral abutments, and semi-integral abutments. This research focused solely on highway bridge abutments, particularly on Ohio Department of Transportation design requirements due to their extensive use of semi-integral abutments. Superstructure elements and geometric requirements are primary …

Effects Of Friction On The Dynamic Behavior Of Flexible Rocking Bodies, S. Mohammadreza Farooghi Mehr, Christine E. Wittich

Department of Civil and Environmental Engineering: Faculty Publications

Flexible rocking bodies are freestanding structures that are free to deform and rock, potentially overturning, when subject to ground excitation. Prior research on the seismic behavior of this type of structure typically assumed sufficient friction at the ground surface to avoid sliding motion. However, experimental observations showed that this assumption was often violated and structures demonstrated non-negligible sliding during their responses. The overarching goal of this study is to evaluate the impact of sliding on the overturning response of flexible rocking bodies. To this end, a two-dimensional analytical model was developed in a Lagrangian formulation, which is presented in this …

Sediment Transport On The River Bandon, Co. Cork, Ireland, Laurence Lomasney

Theses

This thesis analyses sediment transport on the River Bandon, Co. Cork, Ireland. Bedload transport and suspended sediment transport were monitored on the River Bandon over an extended period to determine rates of transport over varying flow conditions. A literature review of sediment properties (individual and bulk sediment), sediment transport, and numerical modelling was undertaken. A manual field sampling programme was undertaken at different locations on the River Bandon to collect bed sediment and suspended sediment for laboratory testing. This data, and data collected using an automatic water sampler and bed sediment traps also, was used to determine baseline conditions for …

Post-Seismic Response And Repair Of Earthquake-Damaged Reinforced Concrete Bridges, Giacomo Fraioli

Doctoral Dissertations

“In bridge structures, column members are typically designed to be the primary source of energy dissipation during an earthquake. Therefore, reinforced concrete (RC) bridges that are damaged in an earthquake tend to have damage to the column members. While many studies have been conducted on seismic strengthening of RC bridge columns, most are focused on retrofit instead of repair. In addition, the limited research on seismic repair of RC bridges has focused on evaluating the response of individual columns (member level), not the bridge structure (system level), due to limitations in modeling and especially testing of full bridge structures. Local …

Innovative Approach To Use Guayule Resin As A Bio-Based Asphalt Alternative, Ahmed Hemida

Doctoral Dissertations

"Asphalt cement will not last long as the world encounters a diminishment in crude oil. Novel resources can contribute to replacing asphalt with the sustainable, flexible pavement. This study presented guayule resin (guayule) as an innovative bio-based asphalt alternative. Ground tire rubber was used as an asphalt enhancer. To judge the guayule's contribution, guayule-based binders were investigated and compared to control asphalt and asphalt-rubber binders. Binders were assessed according to comprehensive Superpave criteria and advanced rheological tests. Component analysis was performed to link the microscale level with the macroscale level. To validate the novel binder, satisfying mix performance tests were …

Sustainability And Environmentally Friendly Methods To Travel Over Waterways, Kendall Kubus

Williams Honors College, Honors Research Projects

Throughout daily traveling, the main structures used are bridges and tunnels. Bridges are used as overpasses over valleys, canyons, and areas that require a large amount of dirt fill to bring the roadway up to the proper grade. Tunnels are underpasses through mountains, under city limits and waterways. The benefits of building a bridge structure is little preparation goes into earth-work and the transportation of aggregate materials. There is some time spent testing surrounding soil to determine the process that will need to occur for foundation preparations in bridge columns. Options for foundation include different types of drilled shafts, caissons, …

A Comparison Of Common Structural Materials, Molly Green

Williams Honors College, Honors Research Projects

This report will compare structural steel, concrete, and lumber through the lenses of mechanical properties, design process, cost, and environmental impact. Steel is a versatile, strong, and lightweight material that comes at a premium price – both financially and environmentally. It is the most expensive material of the three included in this report. This is largely due to its complex manufacturing process that is also responsible for a significant amount of the world’s carbon dioxide emissions. Concrete is significantly less expensive than steel, but the carbon dioxide emissions from manufacturing are approximately equal. Concrete also only performs well in compression …

Steel Diaphragm Innovation Initiative, Year 5, Final Report *Addendum*, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

Preface

The Steel Diaphragm Innovation Initiative (SDII) is a multi-year industry-academic-government partnership to advance the seismic performance of steel floor and roof diaphragms utilized in steel buildings. This addendum to the final report covers work conducted on Task 5.6 which was completed during a no-cost extension conducted in 2021. Please refer to AISI RP21-04, the Steel Diaphragm Innovation Initiative, Year 5, Final Report for all other details.

Inspire Newsletter Spring 2022, Missouri University Of Science And Technology. Inspire - University Transportation Center

INSPIRE Newsletters

No abstract provided.

Review Of Innovative Rehabilitation Techniques For Reinforced Concrete Buildings, Demetrius Karoubas

Graduate Theses, Dissertations, and Problem Reports (ETD)

Building rehabilitation encompasses the act of repairing damaged structural elements, as well as the upgrading of older buildings to bring them up to modern standards. In recent years, due to the extreme economic and environmental cost of new construction, building rehabilitation is gaining ground as the most viable solution to the problem posed by damaged or substandard buildings. With the constant development of new materials with favorable properties and the improvement of our understanding of earthquakes, new rehabilitation techniques are being developed, improving on the efficiency and effectiveness of older ones. Reinforced Concrete (RC) buildings are a type of building …

Experimental And Design Evaluation Of Multi-Bolted Gfrp Joints, Amir Hossein Houshmandyar

Graduate Theses, Dissertations, and Problem Reports (ETD)

For infrastructure system implementation, high strength/stiffness to self-weight ratio, corrosion resistance and ease of fabrication are just a few of the many advantages of pultruded fiber reinforced polymer (PFRP) composites over traditional construction materials. However, challenges of engineered FRP materials are addressed via continuous updating of design codes. For example, the anisotropic nature of FRP composite materials includes different mechanical properties in different directions (pull or longitudinal direction vs. transverse to pull direction) of a structural member, resulting in design complexities over isotropic materials. Typically, infrastructure systems are built by bolting FRP structural members because of certain advantages of bolted …

Repairable Precast Bridge Bents For Seismic Events, Kallan Hart

Electronic Theses and Dissertations

Concrete bridge columns are designed to withstand earthquakes by undergoing large displacements. Current seismic bridge codes guarantee collapse prevention, but damage to concrete and longitudinal reinforcement often requires demolition of the structure. Repairable detailing and advanced bridge construction connections may be utilized in concrete bridge columns to allow for quick construction as well as replacement of damaged reinforcement after an earthquake. This detailing may be an attractive alternative to bridge owners to reduce construction and replacement costs as well as ensure the functionality of critical routes after an earthquake. Three repairable precast bridge columns with exposed longitudinal reinforcement were tested …

Inspire Newsletter Fall 2022, Missouri University Of Science And Technology. Inspire - University Transportation Center

INSPIRE Newsletters

No abstract provided.

Investigation Of The Experimental And Numerical Flexural Behavior Of Innovative Totally Encased Composite Beams, Nour Wehbi, Adnan Masri, Oussama Baalbaki

BAU Journal - Science and Technology

Composite steel-concrete beams have been widely used in long span construction and high rise buildings due to their favorable behavior in terms of high strength, stiffness, and ductility. In this research, the flexural behavior of an innovative steel-concrete composite section is investigated experimentally and verified numerically using ABAQUS software. The studied section is composed of steel tubular specimen or steel hollow pipe totally encased in concrete in the absence of any flexural or shear reinforcement. Instead, steel mesh wraps are used around the tubular steel specimen to provide sufficient steel-concrete bond. All of the studied beams have the same 3m …

New Type Of Lightweight Aggregate For Use In Structural Concrete, Jamal Khatib, Ali Jahami, Oussama Baalbaki, Adel Elkordi

BAU Journal - Science and Technology

This research studied the utilization of municipal solid waste incineration bottom ash (MSWI-BA) in lightweight coarse aggregate (LWC) production. A special method was followed to prepare the new aggregate to fully replace the normal aggregates (NWA) in concrete. The mechanical properties such as compressive strength, tensile strength, and elasticity modulus were investigated for the LWC concrete. Then, two beams were prepared; one from LWC and the other from NWC. The structural performance of beams made up of lightweight aggregates compared to normal aggregates was investigated. The results showed that this type of aggregates led to a 20% reduction in concrete …

Truss Bridge Damage Localization And Severity Estimation Using Influence Lines, Hamoud Alshallaqi

Civil and Environmental Engineering Theses and Dissertations

The safety of bridges is one of the primary concerns of researchers, engineers, and bridge owners and managers, especially when bridges are approaching the end of their intended service lives. The estimation of bridge condition and remaining service life is critical to prioritize the allocation of available funding for repairs and rehabilitation. Various methods, including both dynamic and static approaches, have been developed to detect and localize bridge damage and estimate its severity. This research presents a methodology for detecting a single damaged member in a truss bridge and estimating the severity of the damage using static vertical deflection influence …

Hyperspectral Imaging And Data Analytics For Civil Infrastructure Inspection, Genda Chen

INSPIRE Archived Webinars

In this 50-minute lecture, the fundamental concept of hyperspectral imaging is reviewed. Each hyperspectral image represents a narrow, contiguous wavelength range of an electromagnetic spectrum, which could be indicative of a chemical substance. All the images in the spectral range of a hyperspectral camera are combined to form a three-dimensional hyperspectral data cube with two spatial dimensions and one spectral dimension. A hyperspectral cube can be sampled in four ways: spatial scanning, spectral scanning, snapshot imaging, and spatio-spectral scanning. This presentation will be focused on spatial scanning from a line-scan camera. The feasibility of horizontal imaging from a synchronized hyperspectral …

Effects Of Bonding Pressure And Lamina Thickness On Mechanical Properties Of Clt Composed Of Southern Yellow Pine, Cody S. Bates

Theses and Dissertations

This study produced cross-laminated timber panels at a range of four lamina thickness (5/8, 1, 1 1/8, and 1 1/4 inch) and three bonding pressures (50, 125, 200 psi), producing a total of 12 panels for mechanical testing. The goal of this study is to observe how the thickness and pressure trends affect the mechanical properties of CLT. Tests include flatwise bending, flatwise shear, internal-bond, and delamination. Results showed that bending MOE decreases as the panel thickness increases while bonding pressure had no significance. Bending MOR was less significant for the thickness and more significant for pressure compared to the …

Field Durability Test Of Clt Wall Envelope Using Physical Barriers Against Termites And Structural Performance Of Nailed Hold-Down Brackets Connected To Fungus-Exposed Clt Walls, Kamal Neupane

Theses and Dissertations

The effectiveness of using commercial polyethylene flashing and stainless-steel mesh in CLT wall systems as the termite barriers were evaluated in a short-term field test. American Wood Protection Association (AWPA) E21's visual ratings ranged from 10 to 9 in the specimens showing little damage when no physical barriers were used. Termites were able to crawl beyond the physical barriers in few specimens showing the necessity of further research on height and installation method of physical barriers. On the second part, the effect of decay caused due to Postia placenta, a brown-rot fungus, on the structural performance of hold-down brackets connected …

Additive Manufacturing Of Soil Using Bio-Cementation, Christina Childress

Graduate Theses and Dissertations

Microbially Induced Calcite Precipitation (MICP) is an emerging soil treatment technique that is proven to increase strength, decrease erosion, reduce liquefaction risk, enhance slope stability, decrease compressibility, decrease swelling potential, and overall create a more competent soil. The benefits and applications of MICP are broad, and this research seeks to broaden them further by developing a single-phase additive manufacturing application with no treatment time delay. This is done by analyzing layering behaviors of five USCS soil classifications (100 % Ottawa sand, sand clay mixtures, and 100% lean clay) which provides insight into process variables such as the solution volume and …

Shear Strength Of Concrete Beams Made With Belitic Calcium Sulfoaluminate Cement, Caleb W. Chesnut

Graduate Theses and Dissertations

The need for a cleaner alternative to portland cement (PC) concrete has led to increasing interest in alternatives to PC. Structural properties of most of these alternative cements are still an open research topic. One promising alternative cement is belitic calcium sulfoaluminate (BCSA) cement. The study presented in this paper investigated the shear strength, long term compressive strength, and carbonation in BCSA cement and PC concrete beams. A total of twelve eight-foot long beams were made; eight BCSA cement concrete beams and four PC concrete beams to be tested at various ages depending on cement type. Two beams of each …

Improve The Prediction Of Camber, Deflection, And Prestress Losses In Precast, Prestressed Concrete Bridge Girders, Ahmed Ali Hussein Al Mohammedi

Graduate Theses and Dissertations

Many precast, prestressed concrete girders have camber less or higher than the design values. This discrepancy between the design and the actual camber creates construction problems when installing the cast-in-place concrete deck. The objective of this research was to improve the accuracy of estimating long-term camber, deflection, and prestress losses of precast, prestressed concrete girders.

The experimental program consisted of measuring concrete properties and performing field measurements of camber, deflection, and prestress losses for girders in Arkansas. The investigation involved testing nine full-scale girders from two prestressed concrete plants that regularly supply concrete girders to bridge projects in Arkansas. The …

Connected And Automated Vehicles: Their Implication On Capacity Of A Basic Freeway Section And Impacts On Walkway Safety, Sia Macmillan Lyimo

Dissertations

Autonomous vehicles have recently gained the attention of researchers due to their expected potential benefits on highway traffic streams, such as improving roadway capacity, among others. It is imperative to investigate how these expected benefits can be leveraged in the transportation sector. Understanding the safety and operational benefits helps the concerned transportation agencies and other key stakeholders to make necessary infrastructural and policy adjustments to accommodate such future traffic operation changes. The main goal of this dissertation is to study the impact of connected and automated vehicles on freeway capacity. The simulated environment was created to emulate autonomous vehicle behaviors, …

Relating The Dongre Workability Test To Cold In-Place Recycled Asphalt Pavements, Gus Williams

Civil Engineering Undergraduate Honors Theses

The Dongre Workability Test (DWT) is a test for determining an asphalt pavement’s relative workability from the stress-strain curve of a sample. While the DWT has seen favorable results with warm mix and hot mix asphalt, Casillas and Braham (2020) attempted to apply this test to cold in-place recycled (CIR) asphalt pavements with limited results. This paper looked at the process of reexamining the DWT method to more favorable results with CIR samples. Phase 1 consisted of defining ten possible metrics from the stress-strain curve and applying them to samples with three different curing conditions. From these preliminary results, the …

Gaylord Produce Removal Machine, Marcus Takashi Hirose Lee, Jacob Michael Perlman, Carissa Abigail Kamm, Mark Misao Loera

Mechanical Engineering

This Final Design Review Report outlines the senior design project that began Winter Quarter of 2021 at California Polytechnic State University. Our team consists of three mechanical engineers and a general engineer, working together to design, build, and test a product for Alameda County Food Bank. The goal of the final product is to relieve volunteers and employees of tedious manual labor and increase efficiency during the removal of produce from large Gaylord containers. This document describes background research, the objectives of the project, chosen concept design, analysis and initial prototyping of said concept, the final design, and verification prototype …

Hybrid Structural Health Monitoring Using Data-Driven Modal Analysis And Model-Based Bayesian Inference., Jice Zeng

Electronic Theses and Dissertations

Civil infrastructures that are valuable assets for the public and owners must be adequately and periodically maintained to guarantee safety, continuous service, and avoid economic losses. Vibration-based structural health monitoring (VBSHM) has been a significant tool to assess the structural performance of civil infrastructures over the last decades. Challenges in VBSHM exist in two aspects: operational modal analysis (OMA) and Finite element model updating (FEMU). The former aims to extract natural frequency, damping ratio, and mode shapes using vibrational data under normal operation; the latter focuses on minimizing the discrepancies between measurements and model prediction. The main impediments to real-world …

Seismic Performance Assessment Of Building Contents: Monetary Losses And Injuries, Sereen Majdalaweyh

All Dissertations

Building contents include all the components that are not attached to the building which the owners place after the construction phase, such as furniture, electrical equipment, glassware, and other personal items. Loss and damage assessment of building contents proved to be challenging in performance-based earthquake engineering frameworks because of the data sparsity. Damages to building contents during an earthquake not only cause monetary losses; tumbling and over-toppling of heavy building contents could result in injuries and even deaths of occupants. While major advancements have been made in performance-based earthquake engineering; however, the focus is mainly on damages and collapse risk …

Development Of Lambda Factors For Masonry Design With Lightweight Grout, Rumi Shrestha

All Theses

Reduction in structural mass, improvement in thermal performance, and reduction in shrinkage cracking through internal curing are some of the reasons that lightweight (LW) aggregates have been used in structures and pavements for decades. However, lightweight grout is still not permitted for use in reinforced masonry construction by the TMS 402/602-16 code. In order to realize the benefits of lightweight grout in U.S. reinforced masonry construction, a codified procedure for its use is required which must be informed by experimental testing.

This research is a pilot project directed to characterize the performance of LW grout in comparison to normal weight …