Structural Engineering Commons^™

Preliminary Bond Capacity Exploration Between Monolayer Graphene And Cementitious Composites, Yanping Zhu, Chuanrui Guo, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This Study Aims to Explore Bond Capacity between Monolayer Graphene and Cementitious Composites for the First Time through a Pullout Test. the Low-Pressure Chemical Vapor Deposition Method Was Used to Synthesize Monolayer Graphene on the Copper Substrate to Be Embedded in the Mortar Made by the Briquette Mold. the Bond Capacity between Them Was Higher Than the Tensile Strength of the Copper Sheet with As-Grown Monolayer Graphene on the Surface Since All Specimens Failed in Fracture with Embedment Length of More Than 30 Mm. the Monolayer Graphene Enhanced the Copper Tensile Fracture Stress and Normalized Energy during the Test as …

Multi-Physics Numerical Simulation Of Corrosion And Service Life Evaluation Of Novel Reinforced Concrete Systems, Jin Fan

Dissertations

Durability challenges of reinforced concrete materials can shorten the service life and increase the carbon footprint of civil infrastructure systems. Novel alternative materials, such as high-performance fiber reinforced cementitious composites (HPFRCCs) and recycled aggregate concrete (RAC), offer an alternative to tradi-tional concrete materials by increasing the service life of infrastructure or reducing raw material consumption, thereby reducing the life-cycle carbon footprint. Due, in part, to a lack of robust numerical tools, predicting the durability response of these emerging cementitious materials has been insufficiently addressed. A time-dependent multi-physics modeling framework is proposed and adopted to investigate the chloride induced deterioration mechanisms …

Using Bim To Increase The Efficiency Of Energy-Driven Retrofitting Projects, Anne Grego, Shannon Chance, Barry Mcauley

Conference Papers

The building sector is responsible for nearly 40% of global energy consumption. Many existing buildings have poor thermal insulation and low energy performance, hindering sustainability goals. Energy-driven building retrofitting could address this issue and implementing Building Information Modelling (BIM) in retrofitting can reduce process time, costs, and waste associated with such undertakings. Yet, there is a lack of research and insufficient guidance for implementing BIM in energy-driven retrofitting. A BIM framework is presented to enhance decision-making processes during retrofitting. The aims of this study were to (1) identify BIM technologies and methodologies that could address existing barriers and improve efficiency …

Columbus, Nebraska: Southern Housing Development Design Proposal, Ryan Weyers, Caiden Dynek, Alex Papa, Brexton Robertson, Kaden Perala

Honors Program: Senior Projects (Public)

The following paper proposes the design and creation of a new housing development in the city of Columbus, Nebraska in a lot to the south of the city and directly north of the Columbus wastewater treatment plant. The goal of this proposal is to provide readers with confidence that our company is the most qualified to complete the project and will create the safest, most comfortable, most efficient, and most cost-effective final design. This proposal seeks to offer a solution to the lack of affordable housing for the growing workforce in Columbus. In order to arrive at this solution, each …

A Mechanics-Based Analytical Solution For Restrained Beams With Application To Progressive Collapse Behavior, Leven Deputy

Civil and Environmental Engineering Theses and Dissertations

This dissertation presents an axially restrained beam (ARB) model that incorporates axial-flexural interaction throughout the entire static load-deflection curve: the elastic material range, the plastic, flexural dominant range, the range beyond plastic flexure with increasing catenary effect, and the full catenary range. Energy methods are applied to static load-deflection curves to determine dynamic load-deflection relationships. Specifically, this dissertation considers the two conditions; Pinned-Pinned-Pinned (PPP) which has no flexural resistance at the boundaries, and Fixed-Fixed-Fixed FFF (also Pinned-Fixed-Pinned, PFP) condition which provides the beam with flexural resistance at the boundaries equal to flexural capacity of the beam. Behavior is explained analytically …

3d Printing Of Earthen Materials: Toward The Carbon-Zero Construction, Shiva Bhusal

Civil Engineering ETDs

In recent years, digital manufacturing techniques in the architecture and construction industry have rapidly gained attention, especially with 3D printing, also called additive manufacturing. The use of cement has been common in modern construction and is now being explored for 3D printing. However, due to cement's contribution to approximately 7 percent of global carbon emissions and its high cost, research on sustainable and greener materials has gained attention. Previous studies on alternative construction have examined the mechanical and rheological properties of soil mixes, but not much attention has been given to printability evaluation, shrinkage, and cracking, which can affect the …

Evaluation Of The Geotechnical And Foundation Components On Jud Site, Mirabel W. Nkanor

Honors Theses

This thesis is part of the senior design final project of the Civil Engineering Department at the University of Mississippi. Geotechnical and foundation analyses were done on a proposed construction project for a multi-family home in Orlando, Florida. This evaluation done in this thesis follows the pre-existing geotechnical report on the side, USDA soil reports, ASCE Code 32-01 (Design of Foundations), and ASCE-7 Section 12.31.1 (Foundations and Superstructure-to-Foundation Connections).

A structural system was selected from the proposed location, on the corner of South Conway and Judge Road, and an evaluation of the Bearing Load capacity was completed to determine the …

Three-Dimensional Structural Analysis Of Temple 16 And Rosalila At Copan Ruinas, Luis Tuarez

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Temple 16 is an ancient Maya structure located at the heart of the Copán Ruinas Acropolis in Western Honduras. Temple 16 contains several earlier structures within it that were built on top of each other throughout Copán’s history. One of these earlier structures, Rosalila, is one of the most culturally significant structures within the Acropolis due to its preservation. An intricate series of archeological tunnels have been excavated throughout Temple 16 to allow for its study. However, significant cracking has been observed within Rosalila and several tunnels have experienced partial collapse. This not only poses a life safety issue for …

Song’S Site At Los Angeles Eco-Village Redevelopment, Kendall Gilbert, Marina Rios, Kristin Hernandez, Gianna Morelli

Honors Thesis

The Los Angeles Eco-Village (LAEV) is a co-op housing community, located in Koreatown, focused on building sustainable and economically cooperative living in an urban environment. The purpose of this project is to transform a property recently acquired by the LAEV, called Song’s, into a multipurpose community hub. The project design goals established with LAEV founder and community members, include cultivating new highly sustainable and resilient ideas on urban living and incorporating educational elements that inspire the community and visitors to live more sustainably. This project proposes three design elements to improve the community use of the newly acquired Song’s at …

On The Micro-Mechanical Property Characterization And Bulk-Volume Behavior Prediction Of Additively Manufactured 17-4 Ph Stainless Steels, David González-Niño

Graduate Theses and Dissertations

Selective laser melting is an additive manufacturing technology that opens the possibility to manufacture components with complex geometries that are difficult with traditional manufacturing techniques which could benefit engineering applications such as aviation or structural engineering. However, the lack of a reliable universal predictive model for selective laser melting components could impede the full implementation in industrial applications. Therefore, this dissertation investigates the mechanical behavior of selective laser melting 17-4 PH stainless steel under ultra-low cycle fatigue regime and propose a novel micro-mechanical based modeling using statistical and representative volume element. The first phase of this project examined the mechanical …

Experimental Design For Determining The Cyclic Behavior Of Skewed Reduced Beam Section Moment Connections Having Composite Slabs, Paul Chabaud

Graduate Theses and Dissertations

This paper details the experimental design for determining the cyclic behavior of skewed Reduced Beam Section (RBS) moment connections having composite slabs. The effects of composite concrete slabs on skewed RBS connections subjected to cyclic seismic prequalification loading are addressed in this test setup. Full-scale double-sided RBS SMF specimens representing both interior and exterior column connections are designed and fabricated in this work. Experimental test fixturing and a lateral load application setup within the existing Grady E. Harvell Civil Engineering Research and Education Center (CEREC) are designed. All cyclic loading protocols required for the prequalification testing are described herein. Prequalification …

Development Of Self-Stressing Ultra High-Performance Concrete Using Expansive Chemical Admixtures, Lane Edwards

Graduate Theses and Dissertations

This study investigated the effects of expansive chemical admixtures on ultra-high performance concrete (UHPC) and self-stressing mechanisms. A literature review was performed to determine different types of expansive admixtures for feasibility of the self-prestressing concept. Ultimately it was decided that type-k cement, made by combining Komponent admixture with conventional UHPC, was the most suitable option due to its effects on wet and hardened concrete properties. Mix designs with varying amounts of Komponent were developed to test the effects the admixture had on various properties. Tested properties included, workability, compressive strength, expansion, short-term shrinkage, long-term shrinkage, and developed prestress. The development …

Investigation Of Micp Based 3d Printed Soils, Kathleen Weston

Civil Engineering Undergraduate Honors Theses

The advent of additive manufacturing, often called 3D printing, offers potential for new and more sustainable soil improvement techniques. Previous research at the University of Arkansas has examined Microbially Induced Calcite Precipitation (MICP) as a possible binder option that is a more sustainable alternative to Portland cement and can be used in remote areas where Portland cement may not be available. The objective of this research is to develop an increased understanding of the potential of utilizing MICP as a spray binding technique for applications in 3D printed soils. The specific goals of this research include: examining the effectiveness of …

An Experimental And Numerical Investigation Of The In-Plane Shear Behavior Of Cantilever Cross-Laminated Timber Diaphragms, Bibek Bhardwaj

All Dissertations

This research focuses on investigating the behavior of Cross Laminated Timber (CLT) diaphragms under in-plane shear loads through an experimental, analytical, and numerical approach. Full-scale destructive tests were conducted on cantilever CLT diaphragms to measure their response to cyclic loading. The results showed that the ultimate capacity of the diaphragms was primarily influenced by the fasteners used and exceeded the LRFD capacity. The primary energy dissipation mechanism was through the slip of diaphragm components and rotation of CLT panels due to fastener deformations. The strain data revealed that the diaphragms exhibited deep-beam-like behavior, with resistance to tensile and compressive forces …

Slo Botanical Garden Deck, Noah E. Demer

Architectural Engineering

This project consists of the design and construction of an outdoor-use deck. This deck is to be located in the NE corner of the Sage Meadow at the San Luis Obispo Botanical Garden at 3450 Dairy Creek Rd, San Luis Obispo, CA 93405. This deck’s intended use is as a gathering area for people to congregate. Originally, the ideal deck area was proposed as 700+ square feet, but with further site and project limitations the final design was ~480 square feet. This deck has not been constructed.

Floating Offshore Wind Turbine Project, Courtney Huitt, Cormack Williams

Civil and Environmental Engineering

Offshore wind is a developing industry in the Central Coast with the advent of the future offshore wind project planned off the north coast of San Luis Obispo County. This senior design project aligns with the recently leased wind energy project as a detailed study on the structural design, geotechnical design, and construction of a single 14 MW floating offshore wind turbine (FOWT) located 40 km NW of Morro Bay (NOAA buoy 46028). A preliminary design of a spar FOWT is presented in this project as a solution to the rapidly increasing water depth off the coast of Morro Bay, …

Understanding The Bond Strength Of Bcsa Cement Repair Concrete To Portland Cement Concrete, Brenden Simmons

Civil Engineering Undergraduate Honors Theses

Concrete structures deteriorate over time, and there is an increasing demand for quick repair solutions. Belitic calcium sulfoaluminate (BCSA) cement, a type of rapid setting cement, is thought to be a more sustainable and convenient alternative to portland cement in repair concrete applications. Indicated by the name, rapid setting concrete can set up quicker than traditional portland cement concrete. Because of this, there has been a lot of research about the properties of rapid setting concrete mixes. One of the most popular topics is the strength of the concrete itself. However, there is a need for more research to understand …

Machine Learning-Based Data And Model Driven Bayesian Uncertanity Quantification Of Inverse Problems For Suspended Non-Structural System, Zhiyuan Qin

All Dissertations

Inverse problems involve extracting the internal structure of a physical system from noisy measurement data. In many fields, the Bayesian inference is used to address the ill-conditioned nature of the inverse problem by incorporating prior information through an initial distribution. In the nonparametric Bayesian framework, surrogate models such as Gaussian Processes or Deep Neural Networks are used as flexible and effective probabilistic modeling tools to overcome the high-dimensional curse and reduce computational costs. In practical systems and computer models, uncertainties can be addressed through parameter calibration, sensitivity analysis, and uncertainty quantification, leading to improved reliability and robustness of decision and …

Fatigue Performance Of Flexural Retrofits For Precast Slab Bridges, Ian Stewart

All Theses

This thesis discusses flexural and cyclic load testing of two potential retrofits for pre-cast slab bridges. These slabs came from South Carolina Department of Transportation (SCDOT) decommissioned bridges as a part of an ongoing project with SCDOT. The first is a Carbon Fiber Reinforced Plate (CFRP) retrofit where four CFRP plates were adhesively bonded to the bottom of a slab. The second is a steel plate that was mechanically attached to the bottom of a slab using bolted connections. The bolts were cast into grouted holes in the slab. To better understand the failure mode of these retrofits and their …

Assessing Key Factors Influencing Fire-Induced Spalling Of Concrete Using Explainable Artificial Intelligence (Xai), Mohammad Khaled Gazi Albashiti

All Theses

This thesis adopts eXplainable Artificial Intelligence (XAI) to identify the key factors influencing the fire-induced spalling of concrete and to extract new insights into the fire-induced spalling phenomenon. In this pursuit, an XAI model was developed, validated, and then augmented with two explainability measures, namely, Shapley Additive exPlanations (SHAP) and Local Interpretable Model-Agnostic Explanations (LIME). The proposed XAI model not only can predict the fire-induced spalling with high accuracy (i.e., >92 %) but can also articulate the reasoning behind its predictions (as in, the proposed model can specify the rationale for each prediction instance); thus, providing us with valuable insights …

Assessment Of Bridge Pier Response To Fire, Vehicle Impact, And Air Blast, Chen Fang, Qusai Alomari, Daniel G. Linzell

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Highway bridges exposed to intentional or unintentional fire followed by combined vehicle impact and air blast are at risk of significant damage and, possibly, collapse. Limited studies examining the complex effects of these extreme demands on bridge support elements and parametrizing their response and damage are found in the open literature. Research that is presented is part of an ongoing numerical investigation examining round, multi-column, reinforced concrete (RC), bridge pier behavior subject to multi-hazard scenarios involving fire, vehicle impact, and air blast. Detailed nonlinear finite element analysis models of single columns and multi-column piers supported by a pile foundation system …

Science Club, Danielle Gibson, Krista Andersen

Honors Program: Expanded Learning Clubs

Honors After School program for elementary age children to engage with scientific principles. Students performed hands-on experiments to explore various STEM fields. Each weekly lesson consisted of a different concept to be learned or explored by early elementary aged students.

Feasibility Study For A Continuous Mansfield Hollow State Park Multi-Use Path, Owen P. Spangler

Honors Scholar Theses

This report aims to design a pedestrian river crossing that connects the north and south ends of Mansfield Hollow State Park, utilizing both a new paved pathway and bridge construction. This report first uses GIS data to complete a feasibility study on pathway routing and cost. A preliminary route was selected based on grading and cost analysis. The requirements for constructing a multi-use pathway in the State of Connecticut were then explored, attempting to find a best-fit pathway alignment to accomplish that goal. Through a lengthy literature review, it was found that the pathway design would have to deviate from …

Component Testing And Characterization Of An Innovative Pressurized Sand Damper For The Response Modification Of Structures, Konstantinos Kalfas

Civil and Environmental Engineering Theses and Dissertations

This study is partly motivated by the need to develop sustainable energy dissipation devices that do not suffer from oil leakage due to failure of their end seals and from displacement limitations; and partly from the need to develop a robust damper that consists only of traditional civil engineering materials (sand and steel) in association with the use of post-tensioned steel rods with which practitioner civil engineers are familiar. Past failures of fluid dampers are both disruptive and costly, therefore not in-line with the current design paradigm of sustainable engineering, where the design and construction of structural systems shall meet …

Inter-Wythe Slip Design Criteria For Non-Composite Insulated Walls, Abdelrahman Awawdeh, Fray F. Pozo-Lora, Marc Maguire

Durham School of Architectural Engineering and Construction: Faculty Publications

Non-composite insulated wall connector design is governed by ICC-ES AC320. This standard works entirely in the loading domain, asking the engineer to prevent connector failure due to tension and shear loading. In this paper, the authors discuss additional criteria related to thermal loading and out-of-plane wind loading that create displacement demand in the non-composite connectors. Loads suitable for such analyses are not well defined. Loads are assumed and demonstrated herein and shown to cause significant displacement demand on connectors. Limited non-composite wythe connector testing is available, and some results are presented here. A comparison indicates that outright failure of non-composite …

Indirect Bridge Monitoring Using Crowdsourced Smartphone Data From Passing Vehicles, Jase Sitton

Civil and Environmental Engineering Theses and Dissertations

Bridges become susceptible to deterioration and damage as they age and are subjected to continually increasing demands. Bridge inspections help insure the integrity and safety for service and are conducted on a regular, but usually infrequency, basis. Traditional evaluation methods include visual inspections and permanent sensor installations. Visual inspections are both time and labor intensive and often require bridge closure or service interruption, while cost and logistics complications often prevent practical, widespread deployment of permanent sensor installations. Sensors, including smartphones, in moving vehicles may be used to monitor bridge condition over time and provide valuable insight into the dynamic behavior …

Design Of Wythe Connectors For Concentrated Out-Of-Plane Loading Of Insulated Walls, Ammar Al-Maabreh, Fray F. Pozo, Marc Maguire

Durham School of Architectural Engineering and Construction: Faculty Publications

Partially composite concrete insulated wall panels must be designed to handle different types of loading, including out-of-plane concentrated loads. Currently, there is a lack of information that describes and helps engineers analyze the mechanics of axial load transfer for insulated wall panels for concentrated out-of-plane loads that may occur from lifting, handling, or floor/roof reactions. Such loading generates axial and shear forces in the wythe connectors, making it important to choose the type and quantity of connectors in the design process. This paper aims to develop a better understanding of out-of-plane point load mechanics on concrete sandwich wall panels. A …

Using Thermal Remote Sensing To Quantify Impact Of Traffic On Urban Heat Islands During Covid, My-Thu Tran, Bo Yang

Mineta Transportation Institute

A three-month lockdown in the U.S. at the beginning of the COVID-19 outbreak in 2020 greatly reduced the traffic volume in many cities, especially large metropolitan areas such as the San Francisco Bay Area. This research explores the impact of transportation on climate change by using remote sensing technology and statistical analysis during the COVID-19 lockdown. Using thermal satellite data, this research measures the intensity of the urban heat island, the main driver for climate change during the urbanization process. The research team acquired morning and afternoon MODIS data in the same periods in 2019 before the pandemic and 2020 …

Semi-Annual Progress Report #13, Missouri University Of Science And Technology

Semi-Annual Progress Reports

No abstract provided.

Probability Of Detection In Structural Health Monitoring, Genda Chen

INSPIRE Archived Webinars

The fundamental concept of the probability of detection in structural health monitoring is introduced. The traditional Probability of Detection (POD) method as described in the Department of Defense Handbook MIL-HDBK-1823A for nondestructive evaluation systems does not take the time dependency of data collection into account. When applied to in-situ sensors for the measurement of flaw sizes, such as fatigue-induced crack length and corrosion-induced mass loss, the validity and reliability of the traditional method is unknown. In this 50-minute lecture, the POD for in-situ sensors and their associated reliability assessment for detectable flaw sizes are evaluated using a Flaw-Size-at-Detection (FSaD) method …