Structural Engineering Commons^™

Biomass Production Chlorella Vulgaris Buitenzorg Using Series Of Bubble Column Photo Bioreactor With A Periodic Illumination, Anondho Wijanarko, Dianursanti Dianursanti, Muryanto Muryanto, Josia Simanjuntak, Praswasti Pembangun Dyah Kencana Wulan, Heri Hermansyah, Misri Gozan, Roekmijati Widaningroem Soemantojo

Makara Journal of Technology

Chlorella vulgaris Buitenzorg cultivation using three bubble column photo bioreactors arranged in series with a volume of 200 mL for 130 hours shows an increase of biomass production of Chlorella vulgaris Buitenzorg up to 1.20 times and a decrease of the ability of CO2 fixation compared to single reactor at a periodic sun illumination cycle. The operation conditions on cultivation are as following: T, 29.0oC; P,1 atm.; UG, 2.40 m/h; CO2, 10%; Benneck medium; and illumination source by Phillip Halogen Lamp 20W /12V/ 50Hz. Other research parameters such as microbial carbon dioxide transferred rate (qco2), CO2 transferred rate (CTR), energy …

Ad Hoc On-Demand Distance Vector (Aodv) Routing Protocol Performance Evaluation On Hybrid Ad Hoc Network: Comparison Of Result Of Ns-2 Simulation And Implementation On Testbed Using Pda, Riri Fitri Sari, Abdusy Syarif, Bagio Budiardjo

Makara Journal of Technology

Ad Hoc on-Demand Distance Vector (AODV) Routing Protocol Performance Evaluation on Hybrid Ad Hoc Network: Comparison of Result of Ns-2 Simulation and Implementation on Testbed using PDA. In Mobile Ad hoc NETwork (MANET), node supplemented with wireless equipment has the capacity to manage and organise autonomously, without the presence of network infrastructures. Hybrid ad hoc network, enable several nodes to move freely (mobile) to create instant communication. Independent from infrastructure. They could access the Local Area Network (LAN) or the Internet. Functionalities of ad hoc network very much dependent on the routing protocol that determines the routing around node. Ad …

Substrates Preparation From Woody Tropical Waste Biomass For Biohydrogen Production, Dwi Susilaningsih, Theresia Umi Harwati, Khairul Anam, Yopi Yopi

Makara Journal of Technology

Substrates Preparation from Woody Tropical Waste Biomass for Biohydrogen Production. Addressing to the global warming problem, energy crisis and pollution, hydrogen production by micro-organisms using biotechnological approach should be considered, since it fulfils the recent society requirement to safely produce, renewable and environmental friendly energy. Hydrogen is one of the most promising green energy sources, because it is easily converted to electricity and cleanly combustible. There are three types of micro-organisms for hydrogen production, the first is cyanobacteria through the photosynthesis process, the second is anaerobic bacteria, which use organic substances as electron donor and energy and convert them to …

The Effect Of Ozone And Zeolite Concentration To The Performance Of The Treatment Of Wastewater Containing Heavy Metal Using Flotation Process, Eva Fathul Karamah, Setijo Bismo, Hotdi M. Simbolon

Makara Journal of Technology

The Effect of Ozone and Zeolite Concentration to the Performance of the Treatment of Wastewater Containing Heavy Metal Using Flotation Process. Industrial wastewater which contains heavy metal cannot be disposed to the environment directly, due to its toxicity. In this research, separation of metal from wastewater was conducted by sorptive flotation method, using Lampung natural zeolite as bonding agent. The most common diffuser used in the flotation process is air or oxygen. In this research, ozone is used as diffuser because it is a stronger oxidant and more dissolvable in water than oxygen. Besides, ozone is a coagulant aid and …

Building Fire Safety Audit At Faculty X, University Of Indonesia, Year 2006, Fatma Lestari, Rm. Yodan Amaral Panindrus

Makara Journal of Technology

Building Fire Safety Audit at Faculty X, University of Indonesia, Year 2006. Fire may cause loss of life, material and valuable assets. The objective of this study is to conduct audit for fire safety and emergency response in the building at Faculty X, University of Indonesia, Depok. The audit results on the building fire safety facilities including emergency response and preparedness are then compared to the Building Code Australia (BCA) and Indonesian regulation on the building fire safety (Kep.MenPU.No 10 and 11/KPTS/2000). The building selected are Building A, B, C, D, F and G. Building classification for A, B, D, …

Reinforcement Schemes For Cfs Joists Having Web Openings, K. S. Sivakumaran

CCFSS Library (1939 - present)

No abstract provided.

A Fast Adaptive Wavelet Scheme In Rbf Collocation For Nearly Singular Potential Pdes, Nicolas Ali Libre, Arezoo Emdadi, Edward J. Kansa, Mohammad Shekarchi, Mohammad Rahimian

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

We present a wavelet based adaptive scheme and investigate the efficiency of this scheme for solving nearly singular potential PDEs. Multiresolution wavelet analysis (MRWA) provides a firm mathematical foundation by projecting the solution of PDE onto a nested sequence of approximation spaces. The wavelet coefficients then were used as an estimation of the sensible regions for node adaptation. The proposed adaptation scheme requires negligible calculation time due to the existence of the fast DiscreteWavelet Transform (DWT). Certain aspects of the proposed adaptive scheme are discussed through numerical examples. It has been shown that the proposed adaptive scheme can detect the …

Ccfss Technical Bulletin Spring 2008, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Technical Bulletins (1993 - 2020)

No abstract provided.

Specification For The Design, Testing, And Utilization Of Industrial Steel Storage Racks, Rack Manufacturers Institute

Rack Manufacturers Institute (RMI) Specifications and Manuals (1984 - 2012)

No abstract provided.

Commentary On The Specifications For The Design, Testing, And Utilization Of Industrial Steel Storage Racks, Rack Manufacturers Institute

Rack Manufacturers Institute (RMI) Specifications and Manuals (1984 - 2012)

No abstract provided.

Ccfss News Spring 2008, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Newsletters (1999 - 2008)

No abstract provided.

Development Of Calcium Sulfate – Ggbs – Portland Cement Binders, Brian O'Rourke, Ciaran Mcnally, Mark G. Richardson

Publications

Binders manufactured using a blend of gypsum, ground granulated blast furnace slag and Portland cements are technically viable and possess considerable environmental and economic advantages when compared to binders manufactured using Portland cement alone. As such, the evaluation of binders made from these materials offers a promising research focus in the quest to produce technically sound, environmental and economical binders for specialist uses as an alternative to traditional concrete binders of higher carbon footprint. The aim of the test programme was to investigate the viability of a series of binders designed to fulfil particular user needs while having significantly decreased …

An Assessment Of The Use Of Structural Deformation As A Method Of Determining Area Of Fire Origin, Andrew T. Tinsley, David J. Icove

Safety, Security and Emergency Management Faculty and Staff Scholarship

Current methodologies of origin investigation have yet to include the structural deformations seen in steel buildings as a viable indicator of the area of origin of a given fire. As many steel structures are of relatively large size, it is often difficult to determine the area of origin using the typical dig and sift methods advocated in NFPA 921, especially if the extent of the fire was large and there were no witnesses as to the origin of the fire. As has been investigated for years, the performance of steel is highly affected by the application of heat. The science …

Flexural Behavior And Strength Of Cold-Formed Steel L-Headers, Jesse Pauls, Lei Xu, S. R. Fox

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Flexural Comparison Of The Aci 318-08 And Aashto Lrfd Structural Concrete Codes, Nathan Jeffrey Dorsey

Master's Theses

No abstract provided.

Estimation Of Sound Transmission Class And Impact Insulation Class Rating For Steel Framed Assemblies, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Stable Pde Solution Methods For Large Multiquadric Shape Parameters, Nicolas Ali Libre, Arezoo Emdadi, Edward J. Kansa, Mohammad Rahimian, Mohammad Shekarchi

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

We present a new method based upon the paper of Volokh and Vilney (2000) that produces highly accurate and stable solutions to very ill-conditioned multiquadric (MQ) radial basis function (RBF) asymmetric collocation methods for partial differential equations (PDEs). We demonstrate that the modified Volokh-Vilney algorithm that we name the improved truncated singular value decomposition (IT-SVD) produces highly accurate and stable numerical solutions for large values of a constant MQ shape parameter, c, that exceeds the critical value of c based upon Gaussian elimination.

A Stabilized Rbf Collocation Scheme For Neumann Type Boundary Value Problems, Nicolas Ali Libre, Arezoo Emdadi, Edward J. Kansa, Mohammad Rahimian, Mohammad Shekarchi

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The numerical solution of partial differential equations (PDEs) with Neumann boundary conditions (BCs) resulted from strong form collocation scheme are typically much poorer in accuracy compared to those with pure Dirichlet BCs. In this paper, we show numerically that the reason of the reduced accuracy is that Neumann BC requires the approximation of the spatial derivatives at Neumann boundaries which are significantly less accurate than approximation of main function. Therefore, we utilize boundary treatment schemes that based upon increasing the accuracy of spatial derivatives at boundaries. Increased accuracy of the spatial derivative approximation can be achieved by h-refmement reducing the …

Validation Of Adaptive Aeroelastic Finite Element Program For Two Dimensional Flow Past A Suspension Bridge Girder Section Using Unstructured Grids., Shanique Murray

Civil Engineering Undergraduate Honors Theses

The flow around suspension bridge decks was traditionally investigated using wind tunnel experiments. Computer modeling, an alternative to wind tunnel testing is now being used to simulate the wind flow around a bridge cross section. This alternative is less expensive and takes less time compared to wind tunnel experiments. The motion of flow around a bridge deck is described by a set of partial differential equations called Navier-Stokes (N-S) equations. Flow features such as velocity, pressure and vorticity are predicted by solving these equations. These flow features are then used to compute flow parameters such as aerodynamic drag, lift and …

Reverse Link Cdma System Capacity Evaluation For Stratospheric Platform Mobile Communications, Iskandar Iskandar

Makara Journal of Technology

We propose an analysis of reverse link CDMA multispot beam stratospheric platforms (SPF) in this paper. The SPF is currently proposed as a novel wireless technology for the development of the next generation fixed and mobile communications. The geometry of this technology is different from that of the terrestrial but rather similar to the satellite based cellular system. However, evaluation on the CDMA system capacity of this technology has not been much reported. This paper addresses all possible multiple access interference analyses including the effects of channel fading and shadowing in order to evaluate the system capacity. Single SPF and …

The Potency Of Fire And Explosion Hazard On Premium Oil Storage Tank At Depot X 2007, Fatma Lestari, Warid Nurdiansyah

Makara Journal of Technology

The Potency of Fire and Explosion Hazard on Premium Oil Storage Tank at Depot X 2007. Premium oil storage tanks have fire and explosion risk because Premium oil is flammable liquid. Because of that, fire and explosion risk assessment on Premium oil storage tank at Depot X is needed as foundation to fire and explosion risk management, and comply with regulations. Method of this research is Dow’s Fire and Explosion Index. This research indicate that F&EI value for Premium oil storage tank is 118,82. Based on that F&EI value, level of risk at Premium oil storage tank is intermediate risk.

Limiting Maximum Drag Reduction Asymptote For The Moment Coefficient Of An Enclosed Rotating Disk With Fine Spiral Grooves, Budiarso Budiarso, Keizo Watanabe, Satoshi Ogata

Makara Journal of Technology

In this study, the limiting maximum drag reduction asymptote for the moment coefficient of an enclosed rotating disk with fine spiral grooves in turbulent flow region were obtained analytically. Analysis which were based on an assumption for a simple parabolic velocity distribution of turbulent pipe flow to represent relative tangential velocity, was carried out using momentum integral equations of the boundary layer. For a certain K- parameter the moment coefficient results agree well with experimental results for maximum drag reduction in an enclosed rotating disk with fine spiral grooves and drag reduction ratio approximately was 15 %. Additionally, the experimental …

Co2 Absorption From Its Mixture With Ch4 Or N2 Through Hollow Fiber Membrane Contactor Using Water As Solvent, Sutrasno Kartohardjono, Anggara Anggara, Subihi Subihi, Yuliusman Yuliusman

Makara Journal of Technology

CO2 Absorption from Its Mixture with CH4 or N2 through Hollow Fiber Membrane Contactor using Water as Solvent. Hollow fiber membrane contactors have been widely used as gas-liquid contactors recently such as in the CO2 absorption process from gas stream. This research aims to evaluate the effectiveness of hollow fiber membrane contactor to absorb CO2 from its mixture with CH4 or N2 using water through mass transfer and hydrodynamic tests. There are 3 membrane modules used in this research with shell diameter of 1.9 cm, length of 40 cm, outer fiber diameter of 2.7 mm and fiber number in the …

Trajectory Shaping Of Surface-To-Surface Missile With Terminal Impact Angle Constraint, S. Subchan

Makara Journal of Technology

This paper presents trajectory shaping of a surface-to-surface missile attacking a fixed with terminal impact angle constraint. The missile must hit the target from above, subject to the missile dynamics and path constraints. The problem is reinterpreted using optimal control theory resulting in the formulation of minimum integrated altitude. The formulation entails nonlinear, two-dimensional missile flight dynamics, boundary conditions and path constraints. The generic shape of optimal trajectory is: level flight, climbing, diving; this combination of the three flight phases is called the bunt manoeuvre. The numerical solution of optimal control problem is solved by a direct collocation method. The …

Analysis Of Three Phase Controlled Rectifier With The Same Distance Control As Compared To The Same Angle Control, Sudirman S., Sri Kurniati A.

Makara Journal of Technology

Analysis of three phase controlled rectifier with the same distance control as compared to the same angle control. This research aim to compare the firing of the same distance and the same angle control at three phase controlled rectifier with seen generated harmonic at input (AC side). Then calculate of rectifier efficiency and power factor comparison from both the control type. The rectifier use passive filter with resistance 11 ohm and is analysed with program simulation using PSPICE version 7.1. Result of research indicate that use of the same distance control generates the 5th and 7th harmonics, while the same …

The Use Of Red Cabbage’S Anthocyanine Extract As A Photosensitizer On A Dye-Sensitized Nanocrystalline Tio2 Solar Cell, Akhiruddin Maddu, Mahfuddin Zuhri, Irmansyah Irmansyah

Makara Journal of Technology

The use of Red Cabbage’s anthocyanine extract as a photosensitizer on a Dye-Sensitized Nanocrystalline TiO2 Solar Cell. A solid-state dye-sensitized nanocrystalline TiO2 solar cell utilizing anthocyanin extract form red cabbage as photosensitizer was fabricated. The solar cell was formed in sandwich structure, which two electrodes sandwiching polymer electrolyte containing a redox couple (I-/I3 -). One of the electrodes, namely working electrode, TiO2 layer on TCO (transparent conducting oxide) coated glass substrate was sensitized with anthocyanin dye as electron donor in the system. Another electrode was a carbon sheet as a counter electrode. Gel electrolyte based on PEG (polyethylene glycol) containing …

Effect Of Contact Time On Interface Reaction Between Aluminum Silicon (7% And 11%) Alloy And Steel Dies Skd 61, Bambang Suharno, Neni Octapiani Nurhayati, Bustanul Arifin, Sri Harjanto

Makara Journal of Technology

Effect of Contact Time on Interface Reaction between Aluminum Silicon (7% and 11%) Alloy and Steel Dies SKD 61. Die soldering (die sticking) is a defect of metal casting in which molten metal “welds” to the metallic die mold surface during casting process. Die soldering is the result of an interface reaction between the molten aluminum and the die material. Aluminum alloy with 7 and 11% silicon and SKD 61 die steel are the most common melt and die material used in aluminum die casting. This research is done to study the morphology and the characteristics of the formed AlxFeySiz …

Steel Sheet Sheathing Options For Cfs Framed Shear Wall Assemblies Providing Shear Resistance, Cheng Yu, Hitesh Vora, Tony Dainard, Jimmy Tucker, Pradeep Veetvkuri

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The North American Standard for Cold-Formed Steel Framing - Lateral Design, AISI S213-07, provides design provisions for cold-formed steel framed shear walls with steel sheet sheathing. However, options are limited to 18-mil and 27-mil steel sheet sheathing. Presented in this report are the findings from an extensive monotonic and cyclic testing program conducted at the University of North Texas of 30-mil and 33-mil steel sheet sheathed shear walls with 2:1 and 4:1 aspect ratios and 27-mil sheet steel shear walls with 2:1 aspect ratio and 6-in., 4-in., 3-in., and 2-in. fastener spacing at panel edges. It is anticipated that the …

North American Standard For Cold-Formed Steel Framing -- Floor And Roof System Design, 2007 Edition (Reaffirmed 2012), American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Cold-Formed Steel Framing Design Guide, Second Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

This Design Guide has been developed under the direction of the American Iron and Steel Institute Committee on Specifications for the Design of Cold-Formed Steel Structural Members. The development of the Guide was sponsored by the American Iron and Steel Institute and the Steel Stud Manufacturers Association. The AISI Committee on Specifications wishes to acknowledge and express gratitude to Mr. Thomas Trestain of T. W. J. Trestain Structural Engineering who was the author of this Guide.

With anticipated improvements in understanding of the behavior of cold-formed steel and the continuing development of new technology, this material might become dated. It …