Structural Engineering Commons^™

Wei-Wen Yu International Specialty Conference On Cold-Formed Steel Structures 2018: Recent Research And Developments In Cold-Formed Steel Design And Construction, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

No abstract provided.

Low Fatigue Response Of Crest-Fixed Cold-Formed Steel Drape Curved Roof Claddings, Krishanu Roy, James B. P. Lim, Amir Mohammad Yousefi, G. Charles Clifton, Mahen Mahendran

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold-formed steel roof claddings are subjected to significant suction/uplift pressures during high wind events. In New Zealand, the strong prevailing winds makes this a common occurrence. Suction pressures are generated by the turbulence of the wind flow around the building which can vary both spatially and temporally. The weakest link in the roofing system is the connection between roof sheeting and screw fasteners, which if fails, can lead to progressive collapse of the whole roofing assembly. Fluctuating high wind suction pressures can result in either static or fatigue pull-through failure of the roof sheeting at its screw fastener connections. Current …

Stressed Skin Design Of Steel Sheeting Panels – Part 2: Shear Panels With Sheeting Fixed On All 4 Sides, A. M. Wrzesien, James B. P. Lim, I. A. Macleod, R. M. Lawson

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

In this paper, the strength and stiffness of different roof panels were investigated, in order to establish their ability to act as in-plane diaphragms for stressed skin design of cold-formed steel portal frames. A total of 6 roof panels, approximately 3 x 3m, were examined by testing with sheeting profiles fixed on 4 sides. A variety of sheeting profiles in two industry standard thicknesses of 0.5 and 0.7mm were tested, all using top-hat shaped purlins fixed with self-drilling, self-tapping screws. The experimental strength and stiffness of each panel were then compared against existing design methods. The Finite Element Analysis (FEA) …

Computational Modeling Of Joist-To-Ledger Connections In Cold-Formed Steel Diaphragms, Hernan Castaneda, M. Eng, Kara D. Peterson

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold-formed steel framed buildings can involve a range of options for framing systems, including balloon framing, platform framing, and ledger framing. Transfer of lateral forces from the diaphragms to the wall system (and ultimately to the ground) depends on the interactions within the wall-diaphragm connection, which is dependent on choice of framing system. In ledger framing, floor joists are hung from top of wall studs via a rim track (ledger) and clip angle connection. Recent experimental efforts at Johns Hopkins University studied the wall-diaphragm connection with the goal of quantifying its contribution to overall diaphragm response. Results from these experiments …

Effect Of Connection Details On The Cyclic Behavior Of Nestable Screw Sidelaps, S. Torabian, H. Folk, Benjamin W. Schafer

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The connection strength and stiffness sensitivity of screwed sidelaps in nestable steel decks to screw installation details has been experimentally explored via cyclic testing. The cyclic behavior of sidelaps has been recently incorporated in the high fidelity modeling and seismic evaluation of the steel deck diaphragm in rigid wall - flexible diaphragm buildings, where “unzipping” a sidelap (loss of a significant number of sidelap connections along a deck edge) could significantly reduce the seismic performance of the whole diaphragm. A total of 24 monotonic and cyclic sidelap tests have been performed in the Thin-Walled Structures Laboratory at Johns Hopkins University. …

Fire Resistance Of Cavity Insulated Light Gauge Steel Framed Walls, Anthony Deloge Ariyanayagam, Mahen Mahendran

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Light-gauge steel framed (LSF) wall systems are made of cold-formed steel studs and tracks and lined with gypsum plasterboards. They are mostly cavity insulated to provide acoustic and thermal performance. Cavity insulation delays the temperature rise across the wall as it restrains the heat transfer. This delays the ambient plasterboard surface temperature rise and thus improves the insulation failure time of LSF walls. However, LSF walls are also used as load bearing walls. Having cavity insulation causes the fire side temperatures to increase rapidly, resulting in a higher temperature gradient across the stud depth. This leads to higher thermal bowing …

Shake Table Testing For Seismic Response Evaluation Of Cold-Formed Steel-Framed Nonstructural Architectural Components, Luigi Fiorino, Bianca Bucciero, Tatiana Pali, Ornella Iuorio, Raffaele Landolfo

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The seismic response evaluation of cold-formed steel-framed nonstructural architectural components was investigated in an experimental campaign carried out within of the research study agreement between Knauf Gips KG and the Department of Structures for Engineering and Architecture of the University of Naples “Federico II”. The main objective of this research was to investigate the seismic performance of drywall nonstructural systems, i.e. cold-formed steel-framed indoor partition walls, outdoor façade walls and suspended ceilings. The present paper deals with the dynamic shake table tests. The tests were carried out on two different typologies of prototypes (Type 1 and Type 2) for a …

Numerical Simulation Of The Thermal And Mechanical Behavior Of Cold-Formed Steel Composite Floor Under Fire Conditions, Jixian Peng, Wei Chen, Jihong Ye, Zhengliu Wang

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold-formed steel (CFS) building structures are generally acknowledged as green and industrialized buildings, and the fire resistance behavior has become an important issue. Previous studies were mainly to investigate the fire performance of load-bearing CFS walls lined with different panels. Based on the finite element (FE) software package, ABAQUS, this paper presented a numerical simulation on a new CFS channel joist – ALC (autoclaved lightweight concrete) composite floor under fire conditions. Finally, the present numerical simulation of CFS composite floor in fire was compared with previous full-scaled fire experiments of such floors. The results showed that the temperature progression of …

New Web Crippling Design Rules For Cold-Formed Steel Beams, L. Sundararajah, M. Mahendran, P. Keerthan

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Lipped channel beams (LCBs) and SupaCee sections are commonly used as floor joists and bearers in the construction industry. SupaCee section is one of the cold-formed steel members, which is increasingly used in the building construction sector. It is characterized by unique ribbed web and curved lip elements, and is claimed to be more economical with extra strength than the traditional channel sections. These thin-walled LCBs and SupaCee sections are subjected to specific local and global failures, one of them being web crippling. Several experimental and numerical studies have been conducted in the past to study the web crippling behaviour …

New Proposals For The Direct Strength Method Of Design Of Cold-Formed Steel Beams With Holes In Shear, Song Hong Pham, Cao Hung Pham, Colin A. Rogers, Gregory J. Hancock

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

In the latest North American Specification for the design of cold-formed steel structural members AISI S100-16, an empirical approach is specified to design beams with web holes in shear. Recently, a Direct Strength Method (DSM) of design for shear for perforated beams with the aspect ratio (shear span / web depth) of 1.0 has been proposed. This paper presents a comprehensive review of the proposal and an experimental validation using a test series on beams with the aspect ratio of 2.0 and with various square and circular web opening sizes conducted at the University of Sydney, and other experimental data …

Experimental Investigation Into The Behavior Of Back-To-Back Gapped Built-Up Cold-Formed Steel Channel Sections Under Compression, Krishanu Roy, Tina Chui Huon Ting, Hieng Ho Lau, James B. P. Lim

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Back-to-back gapped built-up cold-formed steel channel-sections are used as compression members in cold-formed steel structures, such as trusses, space frames and portal frames etc. Because of the complex and non-uniform cross section of the back-to-back gapped built- up cold-formed steel channel columns, it is difficult to calculate the strength of these sections accurately. Current guidance by the direct strength method in the AISI Specification and the Australian/New Zealand Standard doesn’t include the gap between the back-to-back channels, thus not being able to predict the axial capacities of these sections accurately. In the literature, very few results have been reported for …

Cyclic Performance And Behavior Characterization Of Steel Deck Sidelap And Framing Connections, S. Torabian, D. Fratamico

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A wide variety of steel deck sidelaps and framing connections have been experimentally studied to characterize the cyclic performance required in seismic evaluation of steel deck diaphragms. This study intends to provide cyclic test results of common steel deck connections including screw nestable and top arc seam sidelaps; and powder actuated fasteners, arc spot weld, and arc seam weld framing connections. A total of 24 sidelap and 36 framing connection tests have been performed in the Thin-Walled Structures Laboratory at Johns Hopkins University by NBM Technologies. The connection test results have been used to parameterize a nonlinear hysteretic spring element …

Screw And Pin Fastener Tests For Cold-Formed Steel, Brian S. Wilson, Fredrick R. Rutz, James R. Harris

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Because of limited available information on strength and ease of installation of specific fasteners for a particular application to a steel deck diaphragm, a preliminary testing program comparing the shear strength of commercially available screws and gas-actuated shot pins was conducted by J. R. Harris and Company at the University of Colorado Denver in 2018. A test was designed to explore the behavior and capacity of various fasteners, securing two and three pieces of sheet steel of various thicknesses together. Specimens were fabricated and load tested, with the sheet steel pieces in tension, so the fasteners were subject to shear. …

Sdi Steel Deck On Cold-Formed Steel Framing Design Manual, Thomas Sputo

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

No abstract provided.

Transverse Shear Stiffness Of Bolted Cold-Formed Steel Storage Rack Upright Frames With Channel Bracing Members, Nima Talebian, Benoit P. Gilbert, Hassan Karampour

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Accurately evaluating the transverse shear stiffness of cold-formed steel storage rack upright frames is crucial to calculate the frame elastic buckling load, perform earthquake design and serviceability checks. This is especially essential for high-bay racks, which are subjected to large second-order effects, and racks supporting the building enclosure, which are exposed to transverse wind loads. The shear behaviour of these frames is poorly understood and experimental testing is usually required to measure their stiffness. Previous studies have shown that Finite Element Analyses (FEA), solely using beam elements, fail to reproduce experimental test results and may overestimate the transverse shear stiffness …

Distortional Buckling Of Cold-Formed Steel Flanges Under Stress Gradient, Robert S. Glauz

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The strength of cold-formed steel beams with stiffened flanges may be controlled by distortional buckling. Buckling stress prediction methods have been developed for flanges under uniform compression. However, channel sections are commonly used where bending occurs about the minor axis with flanges under stress gradient, such that the edges are in compression and the flanges may experience distortional buckling. Current design specifications do not explicitly address this failure mode, which could lead to unsafe designs. This paper presents and verifies an analytical approach for distortional buckling stress prediction for flanges under stress gradient. The approach is consistent with the design …

Experimental Study On Uplift Capacity Of Purlins Considering Restraints From Standing Seam Roof Systems, Wei Luan, Yuanqi Li

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A total of 32 specimens of single-span purlin roof assemblies considering uplift wind load were tested to investigate the structural behavior of cold-formed steel purlins with one flange fastened to standing seam roofs. Failure modes and failure loads of purlins with different parameters were obtained. Full finite element models, incorporate purlins, clips and standing seam roof panels, were developed, and the analysis results were consistent to a high degree with the test results. Using the same element type and material model, the rotational restraint of test roof systems and corresponding influence factors were investigated by finite element models. Finally, using …

Using Generalized Beam Theory To Assess The Behavior Of Curved Thin-Walled Members, Nuno Peres, Rodrigo Goncalves, Dinar Camotim

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

In this work, the first-order behavior of naturally curved thin-walled bars with circular axis, without pre-twist, is assessed with the help of the Generalized Beam Theory (GBT) formulation previously developed by the authors. With respect to the previous work, which dealt with simple cross-sections, the present paper presents a method to obtain the deformation modes for arbitrary flat-walled cross-sections. Despite the complexity involved in this generalization, the standard GBT kinematic assumptions are kept, since they are essential to (i) subdivide the modes in a meaningful way and (ii) reduce the number of DOFs necessary to obtain accurate solutions. It is …

Comparison Of Experimental And Numerical Results For Flexural Capacity Of Light-Gage Steel Roof Deck, Christopher H. Raebel, Dawid Gwodzdz

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The objective of this paper is to present a comparison between experimental results to each of two numerical analyses of cold formed steel roof deck in flexure. Prior numerical studies using the Direct Strength Method (DSM) and the Equivalent Width Method (EWM) have shown discrepancies between results obtained by the two methods. The goal of this research initiative was to compare results from each of the two numerical analysis methods to experimental results in an effort to determine which numerical method is most appropriate for analyzing steel deck in flexure.

Twenty-four physical tests were conducted using four different deck gages …

Localised Screw Connection Failures In Cold-Formed Steel Roofing Systems, Mayooran Sivapathasundaram, Mahen Mahendran

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Lightweight roofing systems made of thin and high strength steel roof sheeting and battens are commonly used in low-rise buildings. However, they often fail frequently at their screw fastener connections during wind storms due to inadequate connection capacities. Two localised failures, known as pull-through and pull-out failures at the screw fastener connections, have been the root cause for extensive loss of roofing systems under high wind uplift loads. Such premature connection failures often cause partial or even complete loss of steel roofing systems and severe damage to building contents. Therefore many experimental studies have been conducted to investigate the pull-through …

A Finite Element Study Of Corrugated Steel Deck Subjected To Concentrated Loads, Vitaliy V. Degtyarev

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

An extensive parametric study was initiated to get a better understanding of steel deck behavior under concentrated loads and to develop design recommendations for a wide range of deck profiles. This paper presents first results from the study related to 1.5-in. deep roof decks of types B and F. The study was performed on non-linear finite element models of deck validated against available test data. Deck gage, span length, span condition, concentrated load locations along and across the deck span were varied in the study. The observed deck behavior under concentrated loads, as well as the effects of the studied …

Sidelap And Structural Fastener Tests For Steel Deck Diaphragms, Y. Shi, S. Torabian, Benjamin W. Schafer, W. S. Easterling, M. R. Eatherton

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Steel deck diaphragm systems, which are commonly used for roof construction in steel-framed buildings, consist of many parts such as corrugated steel deck sheets, sidelap fasteners between adjacent sheets, structural fasteners from the sheets to the supporting beams or joists, chord elements, and collectors. Load-deformation behavior of a steel deck diaphragm system is typically dominated by sidelap and structural fastener limit states. To understand and accurately model the behavior of steel deck diaphragm systems, it is therefore necessary to characterize the behavior of the individual fasteners. The effect of local geometry and detailing at these fasteners such as how the …

Tensile Strength And Serviceability Of Cold-Formed Steel Clip Angles, Wenying Zhang, Zhishan Yan, Mahsa Mahdavian, Mohamad Yousof, Cheng Yu

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

This paper reports the recent research findings of cold-formed steel clip angles in tension. The relevant experimental program and the proposed design methods are presented. The test program involved two phases of testing: Phase I of program focused on the pull-over strength of screw connections on the anchored leg of the clip angles, and Phase II of program concentrated on the tensile strength of the anchored leg of the clip angles within the service deflection limit. Design methods for predicting the pull-over strength as well as tensile strength within the serviceability deformation limit are proposed based on the test results …

Influence Of Gypsum Panels On The Response Of Cold-Formed Steel Framed Strap-Braced Walls, Sophie Lu, Colin A. Rogers

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

In cold-formed steel construction the steel frame is supplemented with either diagonal strap braces or structural sheathing panels (typically steel or wood) to provide overall stability to the structural system and to directly transfer lateral wind and seismic loads through to the foundation as per the design provisions found in AISI S240 (2015) and AISI S400 (2015). Gypsum panels are often specified to provide a fire-resistance rating for the CFS frame, as well as to ensure that adequate sound-proofing exists between adjacent rooms or building units. The engineer may choose to rely on this gypsum to provide additional lateral resistance, …

Design Of Rivet Fastened Rectangular Hollow Flange Channel Beams Subject To Local Buckling, L. Sundararajah, M. Mahendran, P. Keerthan

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The innovative, rivet fastened Rectangular Hollow Flange Channel Beam (RHFCB) is a new type of cold-formed steel section, proposed as an extension to the widely researched hollow flange beams. The hollow flange beams have garnered much interest in the past due to the sections having capacities more typically associated with hot-rolled steel sections. Various researches have been carried out to investigate the behavior of continuously welded hollow flange beams but little is known on the behavior of RHFCBs. The structural behaviour of the RHFCB is unique compared to other conventional cold-formed steel sections and its moment capacity reduces with rivet …

Web Crippling Of Cold-Formed High Strength Steel Square And Rectangular Hollow Sections Under Two-Flange Loading Conditions, Hai-Ting Li, Benjamin Young

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The web crippling behavior of cold-formed high strength steel (HSS) square and rectangular hollow sections under End-Two-Flange and Interior-Two-Flange loading conditions is studied. The cold-formed HSS tubular sections had nominal 0.2% proof stresses of 700 and 900 MPa. Finite element (FE) models were developed and validated against test results, showing the capability of replicating the experimental web crippling strengths, failure modes and load-deformation histories. Upon validation of the FE models, an extensive parametric study comprised 112 FE analyses was performed. The web crippling strengths obtained from the experimental and numerical investigations were compared with the nominal strengths calculated from the …

Parametric Studies And Design Recommendations Of Cold-Formed Steel Sections With Edge-Stiffened Circular Holes Subjected To Web Crippling, Asraf Uzzaman, James B. P. Lim, David Nash, Amir M. Yousefi, Benjamin Young

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A parametric study of cold-formed steel sections with edge-stiffened circular holes subjected to web crippling under one-flange loading condition was undertaken using finite element analysis. The effect of different hole sizes, edge-stiffener length and distances of the web holes to the near edge of the bearing plate on the web crippling strengths of channel sections were investigated. The web crippling strengths are influenced by various geometry parameters: the ratio of the hole depth to the flat portion of the web, a/h, the location of the hole as defined by the distance of the hole from the edge of the …

A Preliminary Study On Stainless Steel Hollow Flange Beams Featuring Lateral-Distortional Buckling, Shuang Niu, Zhidong Zhang, Feng Fan

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

To explore the potential of using stainless steel structurally, extensive research has been carried out to study the structural behavior of stainless steel member as associated with the nonlinear stress-strain relationship. Hollow flange sections feature improved structural efficiency and a unique issue of web distortion. Steel hollow flange sections have been studied and commercially distributed (e.g. the very first HFB section and lately LSB section). As a proactive study, this paper investigates stainless steel hollow flange beams of double-symmetric section with numerical modeling and parametric analysis. The validity of the idealized FE model was verified with existing study on steel …

Study On Distortional Buckling Of Cold-Formed Stainless Steel Beams, Shuang Niu, Zhidong Zhang, Feng Fan

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

In the current research, distortional buckling of cold-formed stainless steel open-section beams was investigated. Four-point bending tests of eight C-section stainless steel beams, made of S30401 alloy, were carried out with global and local buckling precluded by careful design of specimen and test rigs. A detailed finite element model based on ABAQUS was developed and verified against test data. Parametric study was carried out with the verified model, covering four types of sections (C, Z, SupaCee, and SupaZed), three stainless steel alloys (S30401, S44330, S32101), and a series of section slenderness. A convenient method to identify distortional buckling point in …

Flexural Strength Of Continuous-Span Z-Purlins With Paired Torsion Braces Using The Direct Strength Method, Michael Seek

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

A procedure is presented to calculate the local and distortional flexural buckling strength of continuous span purlins with paired torsion braces using the Direct Strength Method. Displacement compatibility is utilized to determine the forces interacting between the purlin, the flexible diaphragm and the torsion braces. The biaxial bending and torsion effects caused by this interaction are superimposed, and the actual distribution of stresses within the cross section are calculated at critical locations along the span. With this distribution of stresses, a finite strip buckling analysis is performed to determine the local and distortional buckling strength. In current design practice, results …