Other Chemical Engineering Commons^™

Effect Of Conveying And Distributive Mixing Elements On Breakage Phenomenon In Twin Screw Granulation, Jiayu Li, Shankali U Pradhan, Carl Wassgren

The Summer Undergraduate Research Fellowship (SURF) Symposium

Twin screw wet granulation (TSG) is gaining more attention and becoming an important process in the pharmaceutical industry. The process is widely implemented because of its flexibility, short residence time, and small equipment footprint. Past studies have shown that screw elements can have a significant impact on the performance of the TSG process. In addition, these studies identified that breakage of wet mass is a significant step in the process. Currently there is no literature that focuses on the effect of each screw element on the breakage process. In this work, experiments have been designed to isolate the breakage process …

Electrodeionization Versus Electrodialysis: A Clean-Up Of Produced Water In Hydraulic Fracturing, Brigitte Marie Rodgers

Graduate Theses and Dissertations

Electrodeionization (EDI) is a widely studied process ranging from applications in wastewater clean-up in the food and beverage industry to purifying organic compounds. To date, there are no apparent studies on applying this technology to produced wastewater recovered from hydraulic fracking sites. Water consumption within hydraulic fracturing sites can reach in the upwards of millions of gallons per site, so a need for a water recycling process becomes necessary within areas where water requirements are scarce. Implementation of an EDI module that is capable of handling high salt solutions from produced wastewater in subsequent fracturing practices will decrease overall water …

Micro Debris Generator, Gordan Bradaric, Ross Byers, Stephen Quanci

Mechanical Engineering

This senior project team at Cal Poly consisting of Stephen Quanci, Gordan Bradaric, and Ross Byers has been commissioned by Erik Brown of Lawrence Livermore National Labs to create a way to reliably and consistently entrain microscopic particles into the hot HTTU flow. These particles will be used to compare the loading rates of new HEPA filters by measuring the pressure drop across the filter. The generated particles would simulate typical conditions in which these HEPA filters are expected to operate, namely fine ash. The particles used for loading the filter are intended to simulate the particulate reaching the LLNL …

Asset Management Model For An Industrial Process Automations System In The Chemical Engineering Unit Operations Laboratory At Rose-Hulman Institute Of Technology, Megan Elaine Liebman

Graduate Theses - Chemical Engineering

In the Chemical Engineering curriculum, the Unit Operations (UO) Laboratory is recognized as the place where hands-on exposure to industrial practices occurs. Students not only examine fundamental engineering principles, but also gain knowledge of the intricacies of modern control technology. The UO Laboratory at Rose-Hulman Institute of Technology houses an industrial state-of-the-art distributed control system, which operates eleven large-scale experiments and interfaces with approximately two hundred process instruments. The size and complexity of the distributed control system and its associated equipment have grown over the past ten years and have reached a point where a systematic asset management approach is …

Nanofiltration Rejection Of Contaminants Of Emerging Concern From Municipal Water Resource Recovery Facility Secondary Effluents For Potable Reuse Applications, Steven Michael Jones

Graduate Theses and Dissertations

As reuse of municipal water resource recovery facility (WRRF) effluent becomes vital to augment diminishing fresh drinking water resources, concern exists that conventional barriers may prove deficient and the upcycling of contaminants of emerging concern (CECs) could prove harmful to human health and aquatic species if more effective and robust treatment barriers are not in place.

There are no federal Safe Drinking Water Act (SDWA) regulations in place specifically for direct potable reuse (DPR) of WRRF effluent. Out of necessity, some states are developing their own DPR reuse regulations. Currently, reverse osmosis (RO) is the default full advanced treatment (FAT) …

Development Of A Simple Handheld Biosensor For Waterborne Pathogens, Bryce C. Jones

Chemical Engineering Undergraduate Honors Theses

Current methods of detecting waterborne pathogens involve testing strips which take 24-48 hours to yield results, or require expensive equipment in order to function. In minimalist environments, these two technologies are not always applicable to test water quality. With the emergence of a new method of PCR, named LAMP PCR, it is possible to quickly and accurately detect pathogen DNA in a water sample. In order to scale this technique into a simple device, the aspects of the reaction must be accommodated, and a visual detection method chosen. A handheld device which keeps the isothermal LAMP PCR stable for the …

Haul Truck Tires Recycling, Marina E. Lee

Chemical Engineering Undergraduate Honors Theses

The Ball Hogs competed in Task 2 - Haul Truck Tires in the 2016 Waste-Management Education and Research Consortium (WERC) International Environmental Design Contest. This task required designing a solution to recycle discarded haul truck tires from mining sites. Our solution was to use the treads of these haul truck tires to construct liners for ball mills. Recycling haul truck tires in this manner would save the mining companies a substantial amount of money and would result in a decrease of carbon emissions.

Efficiency And Particulate Matter Emissions Testing Of Wood Burning Heating Units, Lindsey Mayo

Chemical Engineering Undergraduate Honors Theses

The performance and use of wood-burning stoves as a heating source is carefully regulated by the Environmental Protection Agency (EPA). The EPA requires a rigorous and exhaustive testing protocol be conducted on each unit before it can be sold commercially in order to ensure that the stove in question will not have a detrimental effect on the surrounding environment. However, this testing routine is incredibly time intensive and costly, resulting in a 90% decrease in the number of stove manufacturers since 1988. This decreased competition has ultimately fostered an industry free from competition and motivation to produce clean and efficient …

Removal Of Endocrine Disrupting Compounds From Secondary Municipal Wastewater, Dustin R. Resz

Chemical Engineering Undergraduate Honors Theses

Approximately 1.2 billion people around the world live in areas of physical water scarcity. This could increase to half of the world’s population by 2030 and could displace 24 to 700 million people unless steps are taken to ensure adequate water supply.1 Water scarcity is an escalating issue within the United States, specifically in Western inland states with arid climates. This scarcity is encouraging communities to investigate tertiary level municipal wastewater treatment, allowing for reuse of wastewater. Unfortunately, wastewater contains numerous contaminants that are not regulated by the Environmental Protection Agency (EPA) under the Safe Drinking Water Act (SDWA). Many …

Wastewater Reuse, Zachary J. Bare

Chemical Engineering Undergraduate Honors Theses

Approximately 1.2 billion people around the world live in areas of physical water scarcity. This could increase to half of the world’s population by 2030 and could displace 24 to 700 million people unless steps are taken to ensure adequate water supply. Water scarcity is an escalating issue within the United States, specifically in Western inland states with arid climates. This scarcity is encouraging communities to investigate tertiary level municipal wastewater treatment, allowing for reuse of wastewater. Unfortunately, wastewater contains numerous contaminants that are not regulated by the Environmental Protection Agency (EPA) under the Safe Drinking Water Act (SDWA). Many …

Werc Task #1 - Efficiency And Particulate Matter Emissions Testing Of Wood Burning Heating Units, Jonathan A. Shumaker

Chemical Engineering Undergraduate Honors Theses

A design of a method for calculating the efficiency and particulate matter emission rates was developed for use on wood stoves. The project was completed for the WERC competition which is an international design contest. The prevalence of wood burning as a form of heating, current EPA regulations, and current market conditions were major factors in forming the necessity of this testing method. Design was not limited to outlining the design specifications, the apparatus was built and run. Optimization of the method continued until completion of the project. If the method would continue to be improved then it would be …

Werc Task #1 - Open: Efficiency And Particulate Matter Emissions Testing Of Wood Burning Heating Units, Teni R. Butler

Chemical Engineering Undergraduate Honors Theses

Wood burning has significant environmental and health impacts. This research focused on creating low-cost, reliable test methods for identifying particulate matter emissions to the atmosphere, while obtaining essential data for efficiency calculations of wood combustion.

Direct Band Gap Gallium Antimonide Phosphide (Gasbxp1-X) For Solar Fuels., Harry Benjamin Russell

Electronic Theses and Dissertations

Photoelectrochemical water splitting has been identified as a promising route for achieving sustainable energy future. However, semiconductor materials with the appropriate optical, electrical and electrochemical properties have yet to be discovered. In search of an appropriate semiconductor to fill this gap, GaSbP, a semiconductor never tested for PEC performance is proposed here and investigated. Density functional theory (DFT+U) techniques were utilized to predict band gap and band edge energetics for GaSbP alloys with low amount of antimony. The overall objective of this dissertation is to understand the suitability of GaSb_xP_1-x alloys for photoelectrochemical water splitting application. Specifically, …

Modeling Product Cooling For Baked And Snack Crackers, Jenna Hagenloch

Honors Theses

The cooling of snack crackers, after the baking process is an important step prior to packaging. A model was developed for cooling the crackers. The model allows for the adjustment of multiple operating conditions, such as temperature, depth of the crackers, and the speed of the line. The completed model provides the user with the ability to predict cooling requirements and to validate pre-existing equipment operating conditions. The model will aid in the design of new equipment as well as modifications to improve existing installations to operate within the desired specifications for each process.

Optimizing Chemical & Rheological Properties Of Rejuvenated Bitumen, Dominic Nguyen, Hamzeh Haghshenas Fatmehsari, Santosh Kommidi, Yong-Rak Kim

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

Bitumen has long been a material used in the construction of roadways, yet new pavement only consists of low fractions of recycled materials due to poor compatibility of aged bitumen and new materials. Thus, rejuvenators, chemical additives, have been used in an attempt to re-balance the chemical composition and restore the physical properties of aged bitumen back to its virgin state. A fundamental understanding of how one particular rejuvenator, soybean oil, revitalizes bitumen was investigated using a multi-scale approach.

Fourier-transform infrared spectroscopy (FTIR) was used to determine the changes in chemical properties of pure and rejuvenated virgin and aged samples. …

High Temperature Electrochemical Engineering And Clean Energy Systems, Brenda L. Garcia-Diaz, Luke Olson, Michael Martinez-Rodriguez, Roderick Fuentes, Hector Colon-Mercado, Josh Gray

Journal of the South Carolina Academy of Science

Global power demand is projected to more than double by 2050 and meeting this increased power demand will require maintaining or increasing power output from all existing energy sources while adding a large amount of new capacity. The power sources that have the greatest opportunity to fulfill this demand gap over this time period are clean energy sources including solar and nuclear power. One of the areas of expertise that SRNL has been applying to help with a variety of clean energy technologies is in high temperature electrochemistry. Savannah River National Laboratory (SRNL) in collaboration with industrial and university partners …

The Effect Of Assembly Technique On Weak Polyelectrolyte Multilayer Film Morphology And Humidity Swelling/Deswelling Behavior, Ziyang Yin

Graduate Theses - Chemical Engineering

The goal of this research is to investigate the film morphology and humidity swelling/deswelling behavior of polyelectrolyte multilayers (PEMs) that are constructed from poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) by two assembly techniques: automated dipping layer-by-layer (LbL) and spin-assisted (SA) LbL. Two sets of pH polyelectrolyte solution conditions were tested: (PAH7.5/PAA3.5) and (PAH7.0/PAA7.0). It was found that when the films were constructed with the same number of bilayers (=20 bilayers), SA-LbL (PAH7.5/PAA3.5) has a greater thickness than (PAH7.0/PAA7.0). (PAH7.5/PAA3.5) thin films constructed by automated dipping LbL did not result in a uniform film morphology, making thickness comparisons between techniques …

Methane Emissions As Energy Reservoir: Context, Scope, Causes And Mitigation Strategies, Xiaoli Chai, David J. Tonjes, Devinder Mahajan

Technology & Society Faculty Publications

Methane (CH4) is now considered a bridge fuel between present fossil (carbon) economy and desired renewables and this energy molecule is projected to play an important role in the global energy mix well beyond 2035. The atmospheric warming potential of CH4 is 28-36 times, when averaged over a 100-year period, that of carbon dioxide (CO2) and this necessitates a close scrutiny of global CH4 emissions inventory. As the second most abundant greenhouse gas (GHG), the annual global CH4 emissions were 645 million metric tons (MMT), accounting for 14.3% of the global anthropogenic GHG emissions. Of this, five key anthropogenic sources: …

State-Of-The-Art Review Of Cathodic Protection For Reinforced Concrete Structures, Aimee Byrne, Niall Holmes, Brian Norton

Articles

Cathodic protection (CP) limits the corrosion of a metal surface by making it the cathode of an electrochemical cell. This can be achieved either by using a more active sacrificial anode to create a driving current, or by using inert anodes and impressing a current onto the cathode surface using an external direct current (DC) source. Impressed current cathodic protection (ICCP) is preferred where widespread protection is required, particularly in reinforced concrete structures. ICCP needs a constant DC power supply that is usually provided through a grid connection or independent generators. This paper presents the currently available CP systems for …

Electrochemical Detection Of Antioxidants, Garrett Thompson

Honors Theses and Capstones

No abstract provided.

An Overview Of The Development Of Cement-Based Batteries For The Cathodic Protection Of Embedded Steel In Concrete, Aimee Byrne, Niall Holmes, Brian Norton

Conference papers

This paper presents an overview of the cement-based batteries developed in DIT for use in the cathodic protection of embedded steel in reinforced concrete undergoing chloride-induced corrosion. Cathodic protection delivers an external current (approximately 20mA per m2 of embedded steel) which effectively polarises the internal current generated during corrosion. The batteries developed in DIT comprise of a cement-based electrolyte containing different additives including sand, aggregate, salts, carbon black and plasticiser with protruding anode and cathode metal plates. These batteries produced an initial electrical output of 1.5V and 23mA through a 10 resistor as measured using data acquisition units and a …

Bioluminescent Magnetic Nanoparticles As Potential Imaging Agents For Mammalian Spermatozoa, Erick Salvador Vasquez, Jean M. Feugang, Scott T. Willard, Peter L. Ryan, Keisha B. Walters

Chemical and Materials Engineering Faculty Publications

Background: Nanoparticles have emerged as key materials for developing applications in nanomedicine, nanobiotechnology, bioimaging and theranostics. Existing bioimaging technologies include bioluminescent resonance energy transfer-conjugated quantum dots (BRET-QDs). Despite the current use of BRET-QDs for bioimaging, there are strong concerns about QD nanocomposites containing cadmium which exhibits potential cellular toxicity.

Results: In this study, bioluminescent composites comprised of magnetic nanoparticles and firefly luciferase (Photinus pyralis) are examined as potential light-emitting agents for imaging, detection, and tracking mammalian spermatozoa. Characterization was carried out using infrared spectroscopy, TEM and cryo-TEM imaging, and ζ-potential measurements to demonstrate the successful preparation of these nanocomposites. Binding …

Separation Of Water From Ulsd Using Superhydrophobic Ps Nanofiber Mats, Alisa G. Webel

Williams Honors College, Honors Research Projects

Superhydrophobic polystyrene nanofiber membranes have potential to separate micron scale water droplets from organic due to their hydrophobicity and small pore openings. Polystyrene nanofibers were electrospun into flat sheets and cylindrical filter membranes. The fibers were crosslinked to increase strength and reduce solubility in diesel fuel. The filters were tested and the filtration efficiency was compared to their non-crosslinked counterparts. The optimal electrospinning conditions to create superhydrophobic nanofibers were found to be 20 wt. % PS fibers at 1 mL/hr. under a current of 20kV and at a distance of 20 cm away from the ground. It was found that …

Investigation Of Degradation Of Amine Sorbent, Elijah Arendt

Williams Honors College, Honors Research Projects

The purpose of this study is to investigate the performance of amine-grafted sorbents, specifically when they are degraded at 120°C. This study varied the amine source and the amount of it in the sorbent. The additive type and the amount of it was also manipulated. The performance of sorbents is characterized by CO₂ capture capacity, which is the amount (in mmol) of CO₂ captured per gram of sorbent at 40°C. The best performing sorbents are ones that maintain their CO₂ capture capacity after degradation. When the amount of additive was manipulated, the sorbents containing 2% b.w. and …

Passivation And Potential Fluctuation Of Az31b Alloy In Alkaline Environments, Ana C. Bacco

Williams Honors College, Honors Research Projects

Magnesium (Mg) alloys are used in many industries because of their distinctive properties, but their high chemical reactivity and poor oxide film protection make them inferior. This project focused on investigating the effects of secondary phases and intermetallic particles (IMPs) on the corrosion behavior of AZ31B Mg alloy. The test solution was chloride free NaOH with varying pH levels between 10-14, as well as testing under deaerated conditions. The open circuit potential (OCP) measurements using AZ31B in static NaOH solutions showed potential fluctuation between approximately -1.6 V_SCE (active state) and -0.4 V_SCE (passive state) during the 24-h immersion. …

Separation Of Oil From A Brackish Water Stream, Kayli A. Quinton

Chemical Engineering Undergraduate Honors Theses

In the past 40 years, a variety of enhanced oil recovery (EOR) methods have been developed and applied to mature and mostly depleted oil reservoirs. Chemical and sonic stimulation are two enhanced oil recovery methods in which emulsions are created either as a primary or secondary effect. The resulting emulsion viscosity is considerably lower than that of dry crude thus increasing permeability of and recovery from pay zones. During Chemical enhanced oil recovery, caustic or preformed surfactants are injected into oil reservoirs, which results in flooding and periodic breakthrough of stable oil-water emulsions. The emulsions from chemical enhanced oil recovery …

Heat Transfer Mechanisms In Water-Based Nanofluids., Masoudeh Ahmadi

Electronic Theses and Dissertations

Nanofluids are a class of heat transport fluids created by suspending nano-scaled metallic or nonmetallic particles into a base fluid. Some experimental investigations have revealed that the nanofluids have remarkably higher thermal conductivities than those of conventional pure fluids and are more suited for practical application than the existing techniques of heat transfer enhancement using millimeter and/or micrometer-sized particles in fluids. Use of nanoparticles reduces pressure drop, system wear, and overall mass of the system leading to a reduction in costs over existing enhancement techniques. In this work, the heat transfer coefficient is determined experimentally using copper oxide (CuO) based …

Eicosapentaenoic Acid (Epa) From Porphyridium Cruentum: Increasing Growth And Productivity Of The Microalgae For Pharmaceutical Products, Maryam Asgharpour

Graduate Theses and Dissertations

One of the major nutritional requirements in our diet is an adequate intake of omega-3 specially eicosapentaenoic acid (EPA). In the present study, the effects of two temperatures (16°C & 20˚C) and light intensities (140 & 180µE/M2.S) and four nitrate levels (0.075, 0.3, 0.5 and 0.7g/L) on the cell growth and lipid productivity of Porphyridium cruentum, one of the most promising oil-rich species of microalgae, were investigated. A growth comparison was carried out using pure CO2 and 5% CO2/air. Additionally, the ratio of the fatty acids with omega-3 and omega-6 groups at various growth conditions were compared, since an appropriate …

Field Amplified Sample Stacking On Amyloid Beta (1-42) Oligomers Using Capillary Electrophoresis, Sadia Ali Paracha

Graduate Theses and Dissertations

According to recent literature, it is believed that the oligomeric form of amyloid beta (Aβ) is the leading cause of Alzheimer’s disease (1; 8; 10; 12-18). Additionally, recent studies have eluded to the impact of Alzheimer’s disease (AD) both economically and Socially in today’s society where an increase of about 71% of AD related deaths were recorded between 2000 and 2013 (7). Since the oligomeric forms of Aβ vary in size, shape and some believe conformation, it is vital to utilize a separation technique, such as capilllary electrophoresis (CE) to further understand Aβ aggregation. By understanding Aβ aggregation, treatment of …

Production Of Ethanol From Cereal Food Fines Using Dilute-Acid Hydrolysis, Andrew Edward Arnett

Graduate Theses and Dissertations

Cereal food fines are a leftover by-product from breakfast cereal processing that is typically sold as animal feed or used as a pet food ingredient; however this product could be of greater value as a feedstock for the production of fuel ethanol via fermentation. In order for this material to be fermented it has to be broken down in to simple sugars using hydrolysis. One method of hydrolysis is called dilute-acid hydrolysis, whereby low concentrations of acid are added to the feedstock to facilitate the breaking of chemical bonds. This study investigates the effect of different concentrations of acid to …