Other Chemical Engineering Commons^™

Use Of Photo Isomers To Enhance The Removal Of Lignin From Woody Biomass Hydrolysate, Dipesh J. Karki

Electronic Theses and Dissertations

In this investigation we propose a novel method to enable precipitation of desired solutes using photo-isomers in the extraction solvent. This photo-switchable solvent would enable dissolution or precipitation of desired components using alternating UV or visible light to modify the solubility of the compounds of interest. Three photo-isomers namely native azobenzene, diethoxy azobenzene and diethylamino azobenzene were studied in three different organic solvents: medium chain length alcohol, ethanol and acetone. It was found that among the different combinations of solvent and photo-isomer, acetone and the 4,4’-diethoxy azobenzene solution was most efficient at precipitating dissolved lignin in response to UV light …

Impact Of Local Fluidized Bed Hydrodynamics On The Distribution Of Liquid Sprayed Into The Bed, Yuan Li

Electronic Thesis and Dissertation Repository

In Fluid Coking, heavy oil is sprayed into a fluidized bed of hot coke particles that provide heat for the reaction and vaporization of the products, using nozzles located at different radial and axial locations of the reactor. In industrial units, imperfect initial liquid-solid contact results in the formation of wet agglomerates, which have been shown to cause fouling of the stripper sheds.

This thesis aims to reduce agglomerate formation by modifying the bed hydrodynamics in the spray region by adjusting the initial fluidization gas distribution or using a baffle.

Experimental methods were developed to study local gas flow, solids …

Mitigation Of Fouling And Liquid Losses In A Fluid Coker™: Influence Of Operating Conditions And Internals On Wet-Agglomerates Contribution To Liquid Carry-Under, Yohann Alain François Cochet

Electronic Thesis and Dissertation Repository

In Fluid Cokers, heavy oil is sprayed into a fluidized bed of hot particles through feed ring nozzles located at different heights. Unreacted or partially reacted feedstock, trapped in wet‑agglomerates, reaches the reactor bottom where it causes fouling or is lost to the system burner. The thesis objective is to determine whether modifying the feed distribution between rings or adding baffles can reduce the amount of liquid reaching the reactor bottom.

A model was developed to predict the amount of liquid reaching the reactor bottom. It integrates models for agglomerate formation and rewetting in spray jets, agglomerate drying through heat …

Economic Feasibility Of Mixed Plastic Waste Pyrolysis Using Twin Reactor System In Northwest Arkansas, Carol Rogers, Patricia Means, Renato Gonzalez, Kaida Sheets, Hayden Townsend

Chemical Engineering Undergraduate Honors Theses

Plastic waste generation is increasing at an unsustainable rate while recycling solutions remain stagnant. As a chemical means of recycling, mixed plastic waste pyrolysis can generate synthetic oil appropriate for use as fuel in power generation from plastic waste that otherwise accumulates in landfills. With the scaling of a commercial plastic pyrolysis process in Northwest Arkansas (NWA) modeled after an operational sawdust pyrolysis unit in Huntsville, Arkansas, economic analysis resulted in 26.3% internal rate of return. Therefore, construction of a commercial mixed plastic-to-fuel pyrolysis plant is economically justified and should be pursued. To effectively implement the proposed design, NWA must …

Investigation Of The Stability Of Liquid And Air Films By Synchronized Tri-Wavelength Reflection Interferometry Microscope, Yuesheng Gao

Dissertations, Master's Theses and Master's Reports

Liquid films are widely involved in many processes, such as froth flotation, oil extraction, foam/bubble stabilization, etc. In the meantime, air films are commonly seen in diverse fields like dust control, ink print, coating industry, and so on. Stabilities of these liquid/air films are of great importance to improve the processes. As more and more researchers are paying increasing attention to liquid/air films, tremendous efforts have been made to explore the properties of the films. On the one hand, some theoretical models have also been well developed in recent decades. State-of-the-art technologies, such as AFM, SFA, and RICM, have also …

Call For Abstracts - Resrb 2019, July 8-9, Wrocław, Poland, Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

C.V. - Wojciech Budzianowski, Wojciech M. Budzianowski

Wojciech Budzianowski

-

Renewable Energy And Sustainable Development (Resd) Group, Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

Progress In The Development Of Adaptive Nitride-Based Coatings For High Temperature Tribological Applications, Samir Aouadi, Brandon Luster, Punit Kohli, Christopher Muratore, Andrey Voevodin

Christopher Muratore

Adaptive tribological coatings were recently developed as a new class of smart materials that were designed to adjust their surface chemical composition and structure as a function of changes in the working environment to minimize friction coefficient and wear between contact surfaces. This paper provides an overview of the current research developments in this field, including: (1) Chameleon nanocomposite coatings which are produced by depositing a multi-phase structure whereby some of the phases provide mechanical strength and others are lubricious; (2) Micro- and nano-textured coatings which consist of hard nitride films with highly ordered micropores and nanopores that are subsequently …

Control Of Plasma Flux Composition Incident On Tin Films During Reactive Magnetron Sputtering And The Effect On Film Microstructure, Christopher Muratore, Scott Walton, D. Leonhardt, Richard Fernsler

Christopher Muratore

A hybrid plasma enhanced physical vapor deposition (PEPVD) system consisting of an unbalanced dc magnetron and a pulsed electron beam-produced plasma was used to deposit reactively sputteredtitanium nitride thin films. The system allowed for control of the magnitudes of the ion and neutral flux, in addition to the type of nitrogen ions (atomic or molecular) that comprised the flux. For all deposition experiments, the magnitude of the ion flux incident on the substrate was held constant, but the composition of the total flux was varied. X-ray diffraction and atomic force microscopy showed that crystallographic texture and surface morphology of the …

Control Of Plasma Flux Composition Incident On Tin Films During Reactive Magnetron Sputtering And The Effect On Film Microstructure, Christopher Muratore, Scott Walton, D. Leonhardt, Richard Fernsler

Christopher Muratore

A hybrid plasma enhanced physical vapor deposition (PEPVD) system consisting of an unbalanced dc magnetron and a pulsed electron beam-produced plasma was used to deposit reactively sputteredtitanium nitride thin films. The system allowed for control of the magnitudes of the ion and neutral flux, in addition to the type of nitrogen ions (atomic or molecular) that comprised the flux. For all deposition experiments, the magnitude of the ion flux incident on the substrate was held constant, but the composition of the total flux was varied. X-ray diffraction and atomic force microscopy showed that crystallographic texture and surface morphology of the …

Procesy Cieplne I Aparaty (Lab), Wojciech M. Budzianowski

Wojciech Budzianowski

-

Inżynieria Chemiczna Lab., Wojciech M. Budzianowski

Wojciech Budzianowski

-

Bioluminescent Magnetic Nanoparticles As Potential Imaging Agents For Mammalian Spermatozoa, Erick Salvador Vasquez, Jean M. Feugang, Scott T. Willard, Peter L. Ryan, Keisha B. Walters

Chemical and Materials Engineering Faculty Publications

Background: Nanoparticles have emerged as key materials for developing applications in nanomedicine, nanobiotechnology, bioimaging and theranostics. Existing bioimaging technologies include bioluminescent resonance energy transfer-conjugated quantum dots (BRET-QDs). Despite the current use of BRET-QDs for bioimaging, there are strong concerns about QD nanocomposites containing cadmium which exhibits potential cellular toxicity.

Results: In this study, bioluminescent composites comprised of magnetic nanoparticles and firefly luciferase (Photinus pyralis) are examined as potential light-emitting agents for imaging, detection, and tracking mammalian spermatozoa. Characterization was carried out using infrared spectroscopy, TEM and cryo-TEM imaging, and ζ-potential measurements to demonstrate the successful preparation of these nanocomposites. Binding …

Inżynieria Chemiczna Ćw., Wojciech M. Budzianowski

Wojciech Budzianowski

-

Tematyka Prac Doktorskich, Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

Zespół Energii Odnawialnej I Zrównoważonego Rozwoju (Eozr), Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

Slow Release Of Ions From Internalized Silver Nanoparticles Modifies The Epidermal Growth Factor Signaling Response, Kristen K. Comfort, Elizabeth I. Maurer, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

Due to their distinctive physiochemical properties, including a robust antibacterial activity and plasmonic capability, hundreds of consumer and medical products contain colloidal silver nanoparticles (AgNPs). However, even at sub-toxic dosages, AgNPs are able to disrupt cell functionality, through a yet unknown mechanism. Moreover, internalized AgNPs have the potential to prolong this disruption, even after the removal of excess particles. In the present study, we evaluated the impact, mechanism of action, and continual effects of 50 nm AgNP exposure on epidermal growth factor (EGF) signal transduction within a human keratinocyte (HaCaT) cell line. After AgNP expose, EGF signaling was initially obstructed …

Growth And Properties Of Carbon Microcoils And Nanocoils, Muneaki Hikita, Robyn Bradford, Khalid Lafdi

Chemical and Materials Engineering Faculty Publications

Various types of coiled carbon filaments have been synthesized using chemical vapor deposition and other methods. These carbon filaments exhibit unique electrical and mechanical properties due to their versatile shapes and structures. To form coiled shapes, different types of catalyst compositions and reactive gases have been explored. Generally, coiled carbon filaments are classified by coil diameter and shape (e.g., microcoil and nanocoil). In this review, coiled carbon filaments are classified into three growth mechanism categories:

(1) bidirectional double helical growth;

(2) bidirectional twisted growth; and

(3) tip single helical or twisted growth.

Next, their synthesis methods and hypothetical growth mechanisms …

Termodynamika Procesowa I Techniczna Lab., Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

Tematyka Prac Dyplomowych Dla Studentów Wydziału Mechaniczno-Energetycznego Pwr., Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

Tematyka Prac Dyplomowych Dla Studentów Wydziału Chemicznego Pwr., Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

Mechanika Płynów Lab., Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

Less Is More: Long-Term In Vitro Exposure To Low Levels Of Silver Nanoparticles Provides New Insights For Nanomaterial Evaluation, Kristen K. Comfort, Laura K. Braydich-Stolle, Elizabeth I. Maurer, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

In view of the vast number of new nanomaterials (NMs) that require testing and the constraints associated with animal models, the majority of studies to elucidate nanotoxicological effects have occurred in vitro, with limited correlation and applicability to in vivo systems and realistic, occupational exposure scenarios.

In this study, we developed and implemented a chronic in vitromodel coupled with lower, regulatory dosages in order to provide a more realistic assessment of NM-dependent consequences and illuminate the implications of long-term NM exposure. When keratinocytes were exposed to 50 nm silver nanoparticles (Ag-NPs), we determined that chronically dosed cells operated …

Hydrodynamics In Recirculating Fluidized Bed Mimicking The Stripper Section Of The Fluid Coker, Francisco J. Sanchez Careaga

Electronic Thesis and Dissertation Repository

The stripper section of a Fluid Coker^TM consists of a system of baffles (sheds) that enhances the removal of interstitial and adsorbed hydrocarbon vapors from the fluidized coke-particles. Most of the hydrocarbon-vapors released below a stripper shed flow up to the stripper shed, where they may crack and form coke deposits that foul the shed. Extensive fouling changes the shapes of the sheds, makes them thicker and reduces the free-space between the adjacent sheds until downward solids flow is so impaired that the Coker has to be shut down.

The Radioactive Particle Tracking (RPT) technique allows the determination of …

The Biological Impact Of Concurrent Exposure To Metallic Nanoparticles And A Static Magnetic Field, Kristen K. Comfort, Elizabeth I. Maurer, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

The rapid advancement of technology has led to an exponential increase of both nanomaterial and magnetic field utilization in applications spanning a variety of sectors. While extensive work has focused on the impact of these two variables on biological systems independently, the existence of any synergistic effects following concurrent exposure has yet to be investigated. This study sought to ascertain the induced alterations to the stress and proliferation responses of the human adult low calcium, high temperature keratinocyte (HaCaT) cell line by the application of a static magnetic field (approximately 0.5 or 30 mT) in conjunction with either gold or …

Development And Application Of An Experimental Model For The Fluid Coking Process, Carolina B. Morales

Electronic Thesis and Dissertation Repository

Liquid injection into a fluidized bed is used in industrial applications such as the Fluid Coking^TM process for heavy oil thermal cracking. Poor initial liquid-solid contact results in the formation of agglomerates that limit heat and mass transfer processes, reduce the yield of valuable compounds and create operating problems. The present study develops a new experimental model to simulate the complex phenomena that occur when heavy oil is injected in a Fluid Coker through two-phase nozzles. The model is applied in a pilot scale fluidized bed using scaled-down industrial spray nozzles. The experimental results indicate that agglomerate formation slows …

Tannic Acid Coated Gold Nanorods Demonstrate A Distinctive Form Of Endosomal Uptake And Unique Distribution Within Cells, Emily A. Untener, Kristen K. Comfort, Elizabeth I. Maurer, Christin M. Grabinski, Donald A. Comfort, Saber M. Hussain

Chemical and Materials Engineering Faculty Publications

One of the primary challenges associated with nanoparticle-dependent biological applications is that endosomal entrapment in a physiological environment severely limits the desired targeting and functionality of the nanoconstructs. This study sought to overcome that challenge through a systematic approach of gold nanorod (GNR) functionalization: evaluating the influence of both aspect ratio and surface chemistry on targeted cellular internalization rates and preservation of particle integrity. Owing to their unique spectral properties and enhanced surface area, GNRs possess great potential for the advancement of nanobased delivery and imaging applications. However, their ability for efficient intracellular delivery while maintaining their specific physiochemical parameters …

Mechaniczny Rozdział Faz Proj., Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.

Challenges And Prospects Of Processes Utilising Carbonic Anhydrase For Co2 Separation, Patrycja Szeligiewicz, Wojciech M. Budzianowski

Wojciech Budzianowski

This article provides an analysis of processes for separation CO2 by using carbonic anhydrase enzyme with particular emphasis on reactive-membrane solutions. Three available processes are characterised. Main challenges and prospects are given. It is found that in view of numerous challenges practical applications of these processes will be difficult in near future. Further research is therefore needed for improving existing processes through finding methods for eliminating their main drawbacks such as short lifetime of carbonic anhydrase or low resistance of reactive membrane systems to impurities contained in flue gases from power plants.