Other Chemical Engineering Commons^™

Advancing Sustainable Co2 Mitigation: Experimental And Computational Analysis Of Thermal Carbon Chitosan Sorbent For Automotive Exhaust Capture, Dalia A. Ali Dr., Amir Ahmed Elgamal Eng., Rania Rushdy Moussa Dr.

Chemical Engineering

This study investigated the efficiency of thermal carbon chitosan (TCCS) sorbent for CO2 capture from vehicle exhaust emissions within a designed adsorption system. TCCS was synthesized and meticulously characterized using a series of analytical techniques, including Brunauer-Emmett-Teller (BET) surface area analysis, Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD), Ther- mogravimetric Analysis (TGA), Energy Dispersive X-ray Spectroscopy (EDX), and Differential Scanning Calo- rimetry (DSC). The TCCS adsorbent showed high thermal stability and a heating value (HHV) of 23.5 MJ/kg. Adsorption isotherm study demonstrated that the maximum capacity of CO2 adsorption is 0.084 kg.CO2/kg. TCCS, as well …

Upcycling Waste To Wealth: Cuo-Sio₂/Reduced Graphene Nanocomposite From Pomegranate Peels For One-Pot Low-Temperature Conversion Of Waste Oils Into Valuable Fatty Acid Monomers, Attia Attia, Shahenda Mahran Dr., Maria Centeno Prof., Basudeb Saha

Petroleum Engineering and Gas

and hence reduce the price of the fatty acid monomers. This study reports for the first time a novel, environmentally benign, highly active copper oxide-silica oxide/reduced graphene oxide (CuO-SiO2/RGO), heterogeneous nano-catalyst derived from waste pomegranate peels, for the one-pot, low-temperature synthesis of fatty acid monomers from high-acid-value waste vegetable oil (WVO). The synthesised nano-catalyst was extensively characterised using XRD, FT-IR, TEM, SEM, EDX and TGA-DTA. Further, it was utilised to synthesise fatty acidrich oleic phenoxypropyl acrylate (OPA) monomer from high acid value WVO via a single-step reaction.

Experimental Study For Improving Oil Recovery Using Organic Alkaline And Nano-Silica For An Egyptian Oil Field, Attia Attia, Mohamed Sadek Hamedi Al, Mayar Abdelrahman Hassan Eng.

Petroleum Engineering and Gas

The oil and gas industry continually seeks innovative methods to enhance hydrocarbon recovery due to the declining productivity of conventional techniques. Current recovery methods, such as water flooding and chemical flooding, often face limitations like high interfacial tension, unfavorable wettability, and reduced mobility of oil, especially under harsh reservoir conditions of high salinity. To address these challenges, this study explores the implementation of nanotechnology in enhanced oil recovery (EOR), focusing on the distinct and unique properties of nanoparticles. Nanoparticles, particularly SiO2, were chosen for their ability to significantly decrease interfacial tension, alter wettability, and improve oil mobility. SiO2 nanoparticles exhibit …

A Comparative Study On Natural Vs. Synthesized Polymers Combined With Silica Nanoparticles To Maximize Secondary Oil Recovery, Attia Attia, Mohamed Sadek Hamedi Al, Waleed Abd-Alsabour Ali Eng., Zeyad Tamer Elshony Eng.

Petroleum Engineering and Gas

Polymer flooding is a well-established technique for enhancing oil recovery from reservoirs. In this study, we investigate the performance of two different polymers, Xanthan Gum, and HPAM for secondary oil recovery in the sand pack. The effects of polymer concentration and high salinity on oil recovery are studied. The polymers are characterized using various measurements and tests, including viscosity, shear rate, and interfacial tension. The sand pack flooding experiments are conducted under various conditions, including varying polymer slugs, and nanosilica (silicon dioxide SiO2) concentration. The results are analyzed to determine the optimal conditions for polymer flooding for enhanced oil recovery. …

Development And Characterization Of Automated Screen Mesh-Based Microfluidic Device To Perform Continuous Countercurrent Liquid-Liquid Extraction, Quinn Mcculloch

Nanoscience and Microsystems ETDs

Continuous Countercurrent Microfluidic Liquid-Liquid Extraction (CC-MLLE) shows tremendous potential to generate large numbers of equilibrium stages of separation in a small footprint, with a minimum of pumping, valving, and phase separation steps. However, CC-MLLE rarely appears in literature because it requires a delicate balance between capillary and hydrodynamic forces for deterministic flow.

This dissertation showcases a patented screen mesh-based CC-MLLE invention that performs stable, long-duration (> 36 hr.), countercurrent liquid-liquid extraction and achieves 37 equilibrium stages within a 38.5 μl internal volume. The device is fabricated from chemically resistant polyetheretherketone plastic, using standard machine shop equipment, a plotting cutter, screen …

Nanoparticle Stabilized Interfaces And Their Effect On Foam Stability, Nicole T. Donovan

Dissertations and Theses

No abstract provided.

Synthesis Of Quasi-Freestanding Graphene Films Using Radical Species Formed In Cold Plasmas, Michael A. Mathews Jr.

Graduate Theses, Dissertations, and Problem Reports (ETD)

For over a decade, the Stinespring laboratory has investigated scalable, plasma assisted synthesis (PAS) methods for the growth of graphene films on silicon carbide (SiC). These typically utilized CF₄-based inductively coupled plasma (ICP) with reactive ion etching (RIE) to selectively etch silicon from the SiC lattice. This yielded a halogenated carbon-rich surface layer which was then annealed to produce the graphene layers. The thickness of the films was controlled by the plasma parameters, and overall, the process was readily scalable to the diameter of the SiC wafer.

The PAS process reproducibly yielded two- to three-layer thick graphene films …

Augmented Formic Acid Electro-Oxidation At A Co-Electrodeposited Pd/Au Nanoparticle Catalyst, Yaser M. Asal, Ahmad M. Mohammad, Sayed S. Abd El Rehim, Islam M. Al-Akraa

Chemical Engineering

In this study, the formic acid electro-oxidation reaction (FAEOR) was catalyzed on a Pd-Au co-electrodeposited binary catalyst. The kinetics of FAEOR were intensively impacted by changing the Pd2+:Au3+ molar ratio in the deposition medium. The Pd1-Au1 catalyst (for which the Pd2+:Au3+ molar ratio was 1:1) acquired the highest activity with a peak current density for the direct FAEOR (Ip) of 4.14 mA cm−2 (ca. 13- times higher than that (ca. 0.33 mA cm−2) of the pristine Pd1-Au0 catalyst). It also retained the highest stability that was denoted in fulfilling ca. 0.292 mA cm−2 (ca. 19-times higher than 0.015 …

Synergistic Enhancement Of Formic Acid Electro-Oxidation On Ptxcuy Co-Electrodeposited Binary Catalysts, Yaser M. Asal, Ahmad M. Mohammad, Sayed S. Abd El Rehim, Islam M. Al-Akraa

Chemical Engineering

A propitious binary catalyst composed of Pt and Cu which were electrodeposited simultaneously onto a glassy carbon (GC) substrate was recommended for the formic acid (FA) electro-oxidation reaction (FAOR); the principal anodic reaction in the direct FA fuel cells (DFAFCs). The simultaneous co-electrodeposition of Pt and Cu in the catalyst provided an opportunity to tune the geometric functionality of the catalyst to resist the adsorption of poisoning CO at the Pt surface that represented the major impediment for DFAFCs marketing. The catalytic activity of the catalyst toward FAOR was significantly influenced by the (Pt4+/Cu2+) molar ratio of the electrolyte during …

Peptoid-Functionalized Gold Nanoparticles For Zika Virus Envelope Protein Detection, Meagan Olsen

Chemical Engineering Undergraduate Honors Theses

Detection and identification of viral pathogens is essential in providing effective and rapid medical treatment. Well-established detection methods can be expensive, slow, and sometimes unable to provide the needed sensitivity and specificity. The Zika virus is one clinically relevant pathogen that cannot be easily identified due to cross-reactivity with other viruses from the same family. Electrochemical sensors enhanced with peptoid-functionalized gold nanoparticles (AuNPs) are an alternative to traditional techniques that offers rapid, accurate, label-free pathogen detection for point-of-care diagnostics. To this end, a peptoid capable of binding to the Zika virus envelope protein was developed and its binding affinity for …

Optimization Of Nitrate Removal From Aqueous Solution By Acid-Activated Rice Straw Supported Nano Zero-Valent Iron Using Response Surface Methodology, Dalia A. Ali Eng, Nagwa Mahmoud Al-Mansi Prof, Mohamed Amin Sadek Prof., Ahmad Wafiq Abolnasr Dr.

Chemical Engineering

Rice straw is one of the most common agricultural wastes due to its large production amounts. Energy valorization of rice straw is a technology used for nitrate removal as the produced ashes used to generate the adsorbent by means of an alkali dissolution followed by acid precipitation. The novelty of the proposed process is that the production of the nano zero-valent iron supported acid-activated rice straw (AARS-nZVI) adsorbent is carried out without the energy valorization process but, through an acid activation for rice straw followed by precipitation of nZVI particles on its surface. The new adsorbent synthesis, characterization and application …

Formulation And Validation Of Nanoparticle Controlled Delivery For Chemotherapeutic Drug Products, Shani L. Levit

Theses and Dissertations

Taxol, a formulation of paclitaxel (PTX), is one of the most widely used anticancer drugs, particularly for treating recurring ovarian carcinomas following surgery. Clinically, PTX is used in combination with other drugs such as lapatinib (LAP) to increase treatment efficacy. Delivering drug combinations with nanoparticles has the potential to improve chemotherapy outcomes. In this study, we use Flash NanoPrecipitation, a rapid, scalable process to encapsulate weakly hydrophobic drugs (logP in vitro. Encapsulating either PTX or LAP into nanoparticles increases drug potency. When PTX and LAP are co-loaded in the same nanoparticle, they have a synergistic effect that is greater than …

Group Iv Environmentally Benign, Inexpensive Semiconductor Nanomaterials For Solar Cells, Lisa Je

ENGS 86 Independent Projects (AB Students)

Modern solar cells are composed of silicon, cadmium tellurium, and copper indium gallium diselenide. While these materials are efficient, elements such as cadmium and indium are rare and expensive. To make this renewable energy source more inexpensive and sustainable, the Liu Optics lab is substituting expensive rare earth metals for more commonly found transition state metals. Work has been done to replace the solar cell layers composed of cadmium and gallium to replace them with glass, silicon, and/or thin films. Common metals such as germanium and tin are investigated and characterized to provide a platform for solar cell components.

Iron-Containing Nanoparticles For The Treatment Of Chrionic Biofilm Infections In Cystic Fibrosis, Leisha M. A. Martin

Nanoscience and Microsystems ETDs

Cystic fibrosis (CF) is the most common genetic disease resulting in the morbidity and mortality of Caucasian children and adults worldwide. Due to a genetic mutation resulting in malfunction of the Cystic Fibrosis Transmembrane Conductance Regulator (CFTR) protein, CF patients produce highly viscous mucus in their respiratory tract. This leads to impairment of the mucociliary clearance of inhaled microbes. In addition to reduced microbial clearance, anoxic environmental conditions in the lungs promote biofilm-mode growth of the pathogenic bacterial species Pseudomonas aeruginosa. Chronic infections of P. aeruginosa begin in early childhood and typically persist until respiratory failure and death result. The …

Low Temperature Desiccants In Atmospheric Water Generation., Sunil Gupta

Electronic Theses and Dissertations

Surging global water demand as well as changes to weather patterns and over exploitation of natural water sources, such as ground water, has made potable water a critical resource in many parts of the World already – one rapidly heading towards a crisis situation. Desalination has been adopted as a solution – this is however energy intensive and impractical for most of the developing countries - those most in need of water. A renewable source of energy is solar thermal and solar photovoltaic. A plentiful source of water is the humidity in the atmosphere. This research is to push the …

Nanoparticle Catalytic Enhancement Of Carbon Dioxide Reforming Of Methane For Hydrogen Production, Nicholas Groden

Doctoral Dissertations

The U.S. produces 5559.6 million metric tons of carbon dioxide annually, of which 21% is produced by industrial processes. Steam reforming, an industrial process that accounts for 95% of all hydrogen production in industry, produces 134.5 million metric tons of carbon dioxide or around 11% of the total carbon dioxide produced by industry. This carbon dioxide is then either emitted or goes through a sequestration process that accounts for 75% of the plant's operational costs. An alternative reaction to steam reforming is dry reforming, which utilizes carbon dioxide rather than emitting it and can be used in conjunction with current …

Peptide-Directed Nanoparticle Synthesis With A Denovo Pd-Binding Sequence Fused To A Reporter Protein, Rita Eloisa Tejada Vaprio

Graduate Theses and Dissertations

There is a need for low-cost nanoparticle materials in the context of new technologies for catalyst development. The purpose of this work was to recombinantly produce a 45- amino acid long metal binding peptide that is useful for nanoparticle synthesis. Using splicing by overlap extension PCR, a synthetic gene containing the fusion of the metal binding peptide with Green Fluorescent Protein (GFPUV) was constructed. The metal binding peptide, fused to reporter protein GFPUV, was expressed using high cell density fermentation. Palladium nanoparticles of an average diameter of 1.18 0.45 nm were synthesized by using the crude cell extract containing the …

Synthesis, Characterization, And Activity Of Co/Fe Alumina/Silica Supported Ft Catalysts And The Study Of Promoter Effect Of Ruthenium, Sunday Azubike Esumike

Doctoral Dissertations

The alumina and hybrid alumina-silica FT catalyst were prepared by one-step solgel/oil-drop methods using metal-nitrate-solutions (method-I), and nanoparticle-metaloxides (method-2). The nanoparticle-metal-oxides did not participate in solubility equilibria in contrast to metal nitrate in method-1 causing no metal ion seepage; therefore, method-2 yields higher XRF metal loading efficiency than method-1. The thermal analysis confirmed that the metal loading by method-1 and method-2 involved two different pathways. Method-1 involves solubility equilibria in the conversion of metal-nitrate to metal- hydroxide and finally to metal-oxide, while in method-2 nanoparticle-metal-oxide remained intact during sol-gel-oil-drop and calcination steps.

The alumina supported catalysts were dominated by γ-alumina …

Direct Band Gap Gallium Antimonide Phosphide (Gasbxp1-X) For Solar Fuels., Harry Benjamin Russell

Electronic Theses and Dissertations

Photoelectrochemical water splitting has been identified as a promising route for achieving sustainable energy future. However, semiconductor materials with the appropriate optical, electrical and electrochemical properties have yet to be discovered. In search of an appropriate semiconductor to fill this gap, GaSbP, a semiconductor never tested for PEC performance is proposed here and investigated. Density functional theory (DFT+U) techniques were utilized to predict band gap and band edge energetics for GaSbP alloys with low amount of antimony. The overall objective of this dissertation is to understand the suitability of GaSb_xP_1-x alloys for photoelectrochemical water splitting application. Specifically, …

Minimizing Sheet Resistance Of Organic Photovoltaic Cell Top Contact Electrode Layer: Silver Nanowire Concentration Vs. Conductive Polymer Doping Concentration, Caitlyn Cook

Materials Engineering

The top contact electrode layers of nine organic photovoltaic cells were prepared with two varying factors: three Silver nanowire (AgNW) densities deposited on a conductive polymer doped with three concentrations. Silver’s low sheet resistance of 20-Ω/sq is hypothesized to lower the sheet resistance of the anode layer and thus enhance the overall efficiency of the cell. Four-point probe measurements indicated that increasing AgNW density in the top contact electrode layer of an organic photovoltaic cell significantly reduces sheet resistance from 52.2k-Ω/sq to 18.0 Ω/sq. Although an increase in doping concentration of the conductive polymer reduced sheet resistance in low AgNW …

Developent Of A Phospholipid Encapsulation Process For Quantum Dots To Be Used In Biologic Applications, Logan Grimes

Master's Theses

The American Cancer Society predicts that 1,665,540 people will be diagnosed with cancer, and 585,720 people will die from cancer in 2014. One of the most common types of cancer in the United States is skin cancer. Melanoma alone is predicted to account for 10,000 of the cancer related deaths in 2014. As a highly mobile and aggressive form of cancer, melanoma is difficult to fight once it has metastasized through the body. Early detection in such varieties of cancer is critical in improving survival rates in afflicted patients. Present methods of detection rely on visual examination of suspicious regions …

Electrospinning Applications Air Filtration And Superhydrophobic Materials, Negar Ghochaghi, Adetoun Taiwo

Graduate Research Posters

Electrospinning is a widely applicable technique that generates non-woven fibers in the micro and nano range. In this project two of its applications are highlighted namely filtration media and enhancement of wettability. The first project demonstrates that electrospinning can be used to produce new fiber filtration media with controlled microstructure. The bimodal and unimodal orthogonal and random filters were made and characterized against their filtration efficiency and pressure drop. Figure of Merit (FOM) was also calculated and discussed. It is shown that the FOM increases when the electrospun fibers are arranged into alternating layers of aligned course and fine fibers. …