Phosphate Removal By Spent Low Temperature Shift Catalyst Through Process Optimization And Mechanistic Study, Fatma A. Hashem Eng., Abeer M. Shoaib Prof., Walaa Omar Dr., Mai H. Roushdy

Chemical Engineering

Natural water bodies become eutrophic due to phosphate pollution from industrial and agricultural sectors. This research addresses waste disposal and water pollution at the same time by recycling spent low-temperature shift catalyst (LTSSC) from the fertilizer industry as a sustainable phosphate adsorbent. High surface area (247±5 m2/g), mesoporous structure, and many metal oxide sites (CuO 49%, ZnO 32.2%, and Al2O₃ 13.9%) were shown by characterization using XRF, XRD, BET, SEM–EDX, FTIR, particle size analysis, and zeta potential. Under optimum conditions (contact time 1.64 h, dose 5 g/L, initial concentration 9.58 mg/L, stirring 278 rpm), Response Surface Methodology optimization achieved 92.95±2.8% …

Synergistic Reinforcement Of Lignin–Chitosan Hydrogels Using Vanillin As A Sustainable Green Crosslinker, Moses Ayitey-Adjin Jr., Mohammad Jahid Hasan, Jeremy Erb, Kishore Chand, Garry S. Crosson, Kenya Crosson, Esteban Ureña-Benavides, Erick Salvador Vasquez-Guardado

Chemical and Materials Engineering Faculty Publications

While bio-based hydrogels derived from lignin and chitosan are promising sustainable adsorbents, their practical application is hindered by poor mechanical stability. This study addresses this limitation by synthesizing lignin-chitosan hydrogels using vanillin as a green, bio-derived crosslinker via a facile solution-casting method. The formation of imine (Schiff base) linkages between the aldehyde groups of vanillin and the primary amines of chitosan was confirmed by FTIR spectroscopy (C = N stretching at ~ 1602 cm^− 1). SEM and TGA results demonstrated a reduction in the pore size of the crosslinked hydrogel and an enhanced residual thermal mass. Rheological and …

Magnetic Cellulose Nanocrystal Composites: Synthesis, Properties, Applications, And Opportunities, Mohammad Jahid Hasan, Kishore Chand, Esteban E. Ureña-Benavides, Erick S. Vasquez-Guardado

Chemical and Materials Engineering Faculty Publications

first_page settings Order Article Reprints Open AccessReview

Magnetic Cellulose Nanocrystal Composites: Synthesis, Properties, Applications, and Opportunities

Polymer-Derived Silicon Oxycarbide (Sioc) And Silicon Carbonitride (Sicn) Ceramics For Advanced Electrochemical Energy Storage Applications, Saja Al Ajrash, Erick S. Vasquez-Guardado

Chemical and Materials Engineering Faculty Publications

Preceramic polymers, especially silicon oxycarbide (SiOC) and silicon carbonitride (SiCN) ceramics, have gained significant attention due to their wide range of applications in many fields, particularly in energy storage devices beyond conventional lithium-ion batteries (LIBs). This review focuses on the synthesis, structural characteristics, and properties of SiOC and SiCN ceramics as electrodes for battery applications. Furthermore, their promising applications as electrode materials for energy storage systems are explored, along with the most recent advances in the development of such materials and their use in lithium-ion batteries (LIBs), lithium-sulfur batteries (LSBs), potassium-ion batteries (PIBs), sodium-ion batteries (SIBs), and supercapacitors. This review …

Valorization Of Ductile Cast Iron Solid Waste As A High-Performance Adsorbent For Crystal Violet Removal: Characterization, Optimization, And Mechanistic Insights, Ibrahim Ibrahim Mr., Abdel Mohsen Turky Dr., Nasser Mostafa Prof., Mai H. Roushdy

Chemical Engineering

Industrial textile wastewater containing synthetic dyes cause serious environmental and health risk, whereas ductile cast iron (DCI) foundries generate over 500 000 tons of waste annually. This study utilizes DCI solid waste as an adsorbent to remove the crystal violet (CV) dye from wastewater. Techniques (XRF, XRD, BET, SEM-EDX, FTIR, TGA-DTG, zeta potential) proved that the waste contains 88.0 wt% periclase (MgO) with nanoscale, high surface area, and abundant surface hydroxyl groups. Response surface methodology showed that the most significant parameters were the adsorbent dose and time contact. The optimal conditions give 93.7% removal efficiency at initial concentration: 38.7 mg …

Self-Assembly Interactions In Magnetite-Coated Cellulose Nanocrystals: Implications For Magnetic Hyperthermia Applications, Mohammad J. Hasan, Erin L. Mcneill, Kishore Chand, Juganta Roy, Monishita Deb, Katherine Schlaak, Sydney Herzog, Yvonne Sun, Sarah Watzman, Esteban E. Ureña-Benavides, Erick S. Vasquez-Guardado

Chemical and Materials Engineering Faculty Publications

Magnetic cellulose nanocrystal (MCNC) nanocomposites are promising sustainable and biocompatible platforms for magnetic hyperthermia; however, the molecular mechanisms governing Fe3O4 adsorption and deposition onto CNCs remain poorly understood. Here, sulfated (S-CNC) and TEMPO-oxidized CNCs (T-CNC) were used to prepare nanocomposites at 1:2 and 1:4 CNC:Fe3O4 mass ratios, enabling a systematic evaluation of how surface chemistry and nanoparticle loading dictate interfacial interactions and magneto-colloidal behavior. Bare magnetite nanoparticles were 21 ± 5 nm by TEM but grew to 144 ± 18 in the DLS measurement at pH 7. The S-CNC nanocomposites had hydrodynamic sizes between 144 and 210 nm, not much …

Advancing Sustainable Co2 Mitigation: Experimental And Computational Analysis Of Thermal Carbon Chitosan Sorbent For Automotive Exhaust Capture, Dalia A. Ali Dr., Amir Ahmed Elgamal Eng., Rania Rushdy Moussa Dr.

Chemical Engineering

This study investigated the efficiency of thermal carbon chitosan (TCCS) sorbent for CO2 capture from vehicle exhaust emissions within a designed adsorption system. TCCS was synthesized and meticulously characterized using a series of analytical techniques, including Brunauer-Emmett-Teller (BET) surface area analysis, Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FTIR), X-ray Diffraction (XRD), Ther- mogravimetric Analysis (TGA), Energy Dispersive X-ray Spectroscopy (EDX), and Differential Scanning Calo- rimetry (DSC). The TCCS adsorbent showed high thermal stability and a heating value (HHV) of 23.5 MJ/kg. Adsorption isotherm study demonstrated that the maximum capacity of CO2 adsorption is 0.084 kg.CO2/kg. TCCS, as well …

Upcycling Waste To Wealth: Cuo-Sio₂/Reduced Graphene Nanocomposite From Pomegranate Peels For One-Pot Low-Temperature Conversion Of Waste Oils Into Valuable Fatty Acid Monomers, Attia Attia, Shahenda Mahran Dr., Maria Centeno Prof., Basudeb Saha

Petroleum Engineering and Gas

and hence reduce the price of the fatty acid monomers. This study reports for the first time a novel, environmentally benign, highly active copper oxide-silica oxide/reduced graphene oxide (CuO-SiO2/RGO), heterogeneous nano-catalyst derived from waste pomegranate peels, for the one-pot, low-temperature synthesis of fatty acid monomers from high-acid-value waste vegetable oil (WVO). The synthesised nano-catalyst was extensively characterised using XRD, FT-IR, TEM, SEM, EDX and TGA-DTA. Further, it was utilised to synthesise fatty acidrich oleic phenoxypropyl acrylate (OPA) monomer from high acid value WVO via a single-step reaction.

Synthesis And Characterization Of Temperature- And Ph-Responsive Pia-B-Pnipam@Fe3O4 Nanocomposites, Swati Kumari, Cayla Cook, Fatema Tarannum, Erick Salvador Vasquez-Guardado, Olufemi Ogunjimi, Keisha B. Walters

Chemical and Materials Engineering Faculty Publications

Stimuli-responsive polymers (SRPs) have garnered significant attention in recent decades due to their immense potential in biomedical and environmental applications. When these SRPs are grafted onto magnetic nanoparticles, they form multifunctional nanocomposites capable of various complex applications, such as targeted drug delivery, advanced separations, and magnetic resonance imaging. In this study, we employed a one-step hydrothermal method using 3-aminopropyltrimethoxysilane (APTES) to synthesize APTES-modified Fe₃O₄ nanoparticles (APTES@Fe₃O₄) featuring reactive terminal amine groups. Subsequently, via two consecutive surface-initiated atom transfer radical polymerizations (SI-ATRP), pH- and temperature-responsive polymer blocks were grown from the Fe₃O …

Magnetic Nanoparticles: Synthesis And Applications In Life Sciences, Kishore Chand, Erick Salvador Vasquez

Chemical and Materials Engineering Faculty Publications

Magnetic nanoparticles (MNPs) are multifunctional materials with superparamagnetic properties and tunable surface chemistries, making them valuable across diverse fields, such as biomedicine, environmental remediation, and agriculture. This review examines recent advancements in MNP synthesis, encompassing chemical, physical, and environmentally friendly methods while highlighting improvements in size, morphology, and composition control that enhance application-specific performance and environmental sustainability. The review discusses various architectures, including single-core, core–shell, hybrid composites, and stimuli–responsive systems, with an emphasis on their stability, scalability, and functionalization potential. In biomedical applications, MNPs show promise in targeted drug delivery, magnetic hyperthermia, and magnetic resonance imaging contrast enhancement, where biocompatibility, …

Work In Progress: Exploring The Impact Of International Experiences On The Development Of Students’ Entrepreneurial Mindset, Olgha Bassam Qaqish, Marcia Pool, William H. Pennock, Erick Salvador Vasquez, Fahmidah Ummul Ashraf

Chemical and Materials Engineering Faculty Publications

International experiences, including collaborative online international learning (COIL) experiences that naturally increase accessibility, are of interest to many undergraduate students. These experiences provide educators a unique opportunity to develop a student's entrepreneurial mindset (EM). Additionally, hands-on experiences aligned with the National Academy of Engineering’s (NAE) grand challenge themes (Sustainability, Security, Health, and Joy of Living) support connections between the experience, disciplinary knowledge, multicultural awareness, and EM. Through this Work-in-Progress (WiP) study, we seek to answer: 1) How do international experiences influence undergraduate science and engineering students’ EM, and 2) How does the international experience modality (i.e., study abroad or COIL) …

Camino—Career Advancement, Mentorship, Inspiration, And Opportunities: A Stem K-12 Outreach Initiative, Hector A. Pulgar, Francisco Zelaya-Arrazabal, Erick Salvador Vasquez, Sebastian N. Martinez Lizana

Chemical and Materials Engineering Faculty Publications

CAMINO is a STEM program designed to promote career advancement, provide mentorship, give inspiration, and offer opportunities for K-12 Hispanic students located in East Tennessee. As part of the educational component of an NSF CAREER grant, the program launched in 2021 and is a collaboration between a research group from the University of Tennessee and one of the high schools with the largest Hispanic populations in the Knoxville Metropolitan area. These students from minority backgrounds may limit their aspirations and may not pursue higher education and/or professional development for numerous reasons, such as limited motivation, insufficient exposure to higher education, …

Entrepreneurially Minded Learning (Eml) Micromoment Activities Generated Using Students' Experiences In A Fluid Flow And Heat Transfer Course, Erick Salvador Vasquez, Megan Morin

Chemical and Materials Engineering Faculty Publications

The Entrepreneurially Minded Learning (EML) Framework involves the 3 C's: curiosity, connections, and creating value. Several design courses, open-ended assignments, and laboratory experiences can successfully lead to EML implementations. However, these implementations require extensive class time and instructor feedback, limiting their use in core engineering courses. Developing EML activities that are active, engaging, and rapid to deploy in a classroom setting can promote the sustained growth of an entrepreneurial mindset (EM). EML micromoment activities are emerging as a practical tool to facilitate the incorporation of the 3 Cs through rapid activity implementations that only last 2 – 30 minutes. These …

Student-Led Video Podcasting In A Chemical Behavior Of Materials Course, Erick Salvador Vasquez

Chemical and Materials Engineering Faculty Publications

Video podcasts, or vodcasts, are a form of podcasting that combines video and audio to deliver various types of educational content effectively. To our knowledge, very few studies have focused on student-produced podcasting for learning technical engineering concepts. This study explores using student-created technical videos in a course on the chemical behavior of materials through three separate assignments. The first assignment centered on sustainability aspects. Students, divided into groups of three, were tasked to review two influential journal articles on plastic waste input into the ocean and metal recycling. Each group had to prepare and deliver a technical script about …

A High-Temperature Lithium-Aluminum Alloy/Oxygen Or Air Fuel Cell, Sarwan S. Sandhu

Chemical and Materials Engineering Faculty Publications

This paper is in support of our current effort in the development of an experimental hybrid (lithium- aluminum alloy/electrolyte/oxygen or air) fuel cell for the acquisition of the experimental data required to characterize its performance behavior. The literature-based assembled formulation provided in this paper can be used to predict the cell open-circuit electric potential, lithium amount in the cell anode alloy, and g-atom ratio of lithium to aluminum in the cell anode as a function of time at any cell discharge current level. The ohmic voltage losses can also be computed in the cell cathode, anode, and two electrolytes at …

Experimental Study For Improving Oil Recovery Using Organic Alkaline And Nano-Silica For An Egyptian Oil Field, Attia Attia, Mohamed Sadek Hamedi Al, Mayar Abdelrahman Hassan Eng.

Petroleum Engineering and Gas

The oil and gas industry continually seeks innovative methods to enhance hydrocarbon recovery due to the declining productivity of conventional techniques. Current recovery methods, such as water flooding and chemical flooding, often face limitations like high interfacial tension, unfavorable wettability, and reduced mobility of oil, especially under harsh reservoir conditions of high salinity. To address these challenges, this study explores the implementation of nanotechnology in enhanced oil recovery (EOR), focusing on the distinct and unique properties of nanoparticles. Nanoparticles, particularly SiO2, were chosen for their ability to significantly decrease interfacial tension, alter wettability, and improve oil mobility. SiO2 nanoparticles exhibit …

A Comparative Study On Natural Vs. Synthesized Polymers Combined With Silica Nanoparticles To Maximize Secondary Oil Recovery, Attia Attia, Mohamed Sadek Hamedi Al, Waleed Abd-Alsabour Ali Eng., Zeyad Tamer Elshony Eng.

Petroleum Engineering and Gas

Polymer flooding is a well-established technique for enhancing oil recovery from reservoirs. In this study, we investigate the performance of two different polymers, Xanthan Gum, and HPAM for secondary oil recovery in the sand pack. The effects of polymer concentration and high salinity on oil recovery are studied. The polymers are characterized using various measurements and tests, including viscosity, shear rate, and interfacial tension. The sand pack flooding experiments are conducted under various conditions, including varying polymer slugs, and nanosilica (silicon dioxide SiO2) concentration. The results are analyzed to determine the optimal conditions for polymer flooding for enhanced oil recovery. …

Efficient Phosphate Removal From Water Using Ductile Cast Iron Waste: A Response Surface Methodology Approach, Mai Hassan Roushdy Dr., Nada Amr El-Khashab Eng,, Ahmed Ibrahim Osman Dr., Dalia Amer Ali Dr.

Chemical Engineering

Water scarcity is a critical issue worldwide. This study explores a novel method for addressing this issue by using ductile cast iron (DCI) solid waste as an adsorbent for phosphate ions, supporting the circular economy in water remediation. The solid waste was characterized using XRD, XRF, FTIR, and particle size distribution. Wastewater samples of different phosphate ion concentrations are prepared, and the solid waste is used as an adsorbent to adsorb phosphate ions using different adsorbent doses and process time. The removal percentage is attained through spectrophotometer analysis and experimental results are optimized to get the optimum conditions using Design …

Glycerol-Free Biodiesel Via Catalytic Interesterification: A Pathway To A Netzero Biodiesel Industry, Nessren Farrag, Omar Youssef Youssef, Esraa Khaled, Omar Aboelazayem

Chemical Engineering

Conventional biodiesel manufacturing uses alcohol as an acyl acceptor, resulting in glycerol as a side product. The increased demand for biodiesel has led to the production of a substantial surplus of glycerol, exceeding the market need. Consequently, glycerol is now being regarded as a byproduct, and in some cases, even as waste. The present study aims to suggest an economically viable and ecologically friendly approach for maintaining the viability of the biodiesel sector. This involves generating an alternative byproduct of higher value, rather than glycerol. Triacetin is produced through the interesterification of triglycerides with methyl acetate, and is a beneficial …

Performance And Environmental Assessment Of Biochar-Based Membranes Synthesized From Traditional And Eco-Friendly Solvents, Abelline Katusiime Fionah, Isaac Oluk, Laura Brady, Diana M. Byrne, Isabel Escobar

UK CARES Faculty Publications

Water contamination resulting from coal spills is one of the largest environmental problems affecting communities in the Appalachia Region of the United States. This coal slurry contains potentially toxic substances, such as hydrocarbons, heavy metals, and coal cleaning chemicals, and its leakage into water bodies (lakes, rivers, and aquifers) can lead to adverse health effects not only for freshwater bodies and plant life but also for humans. This study focused on two major experiments. The first experiment involved the use of biochar to create a biochar–polysulfone (BC-PSf) flat-sheet multifunctional membrane to remove organic contaminants, and the other major experiment compared …

Assessing Global Engagement Interventions To Advance Global Engineering Competence For Engineering Formation, Scott Schneider, Erick S. Vasquez-Guardado, Corinne Mowrey, Michael Moulton, Homero Murzi, Matthew A. Witenstein

Chemical and Materials Engineering Faculty Publications

This paper summarizes the work performed during the first year of a collaborative Research Initiation in Engineering Formation (RIEF) project focused on assessing the formation of a global learner mindset in engineering students through the use of different types of global engagement interventions without extended international travel. During this year the global engagement interventions have been developed, piloted, and assessed using the Global Engagement Survey (GES) and Global Engineering Competency Scale (GECS) instruments in a pre and post format. The assessment results helped the research team update the interventions and refine the assessment strategy, including the addition of new qualitative …

Work In Progress: Exploring The Impact Of International Experiences On The Development Of Students’ Entrepreneurial Mindset, Olgha Bassam Qaqish, Marcia Poole, William Pennock, Erick S. Vasquez-Guardado, Fahmidah Ummul Ashraf

Chemical and Materials Engineering Faculty Publications

International experiences, including collaborative online international learning (COIL) experiences that naturally increase accessibility, are of interest to many undergraduate students. These experiences provide educators a unique opportunity to develop a student's entrepreneurial mindset (EM). Additionally, hands-on experiences aligned with the National Academy of Engineering’s (NAE) grand challenge themes (Sustainability, Security, Health, and Joy of Living) support connections between the experience, disciplinary knowledge, multicultural awareness, and EM. Through this Work-in-Progress (WiP) study, we seek to answer: 1) How do international experiences influence undergraduate science and engineering students’ EM, and 2) How does the international experience modality (i.e., study abroad or COIL) …

Enhancing Entrepreneurial Minded Learning Of Process Control And Heat Transfer Concepts Using Micromoments And Concept Maps, Erick S. Vasquez-Guardado, Ricardo Gomez Gonzalez, Jean M. Andino, Nilza D. Aples, Xiaojing Yuan

Chemical and Materials Engineering Faculty Publications

The Entrepreneurially Minded Learning (EML) Framework seeks to infuse an Entrepreneurial Mindset in engineering students. The EML framework is founded on the 3 C’s principles of curiosity, connections, and creating value. Assessing EML efforts, however, is a well-known challenge for many engineering courses that do not have a design component. Through concept maps and micromoment activities, this work seeks to answer the following questions: Does implementing micromoment activities enhance students’ EML in two core areas of chemical engineering, i.e., heat transfer and process controls? A secondary research question is whether introducing a physical device in lectures enhances students’ EML. The …

Using Micromoments And Concept Maps To Enhance Entrepreneurially Minded Learning Of Indoor Air Pollution Control, Jean M. Andino, Erick Salvador Vasquez-Guardado, Ricardo Gomez Gonzalez, Xiaojing Yuan, Nilza D. Aples

Chemical and Materials Engineering Faculty Publications

Micromoments targeted toward indoor air quality were introduced to students in an Air Quality Engineering course to enhance their entrepreneurial mindset. Three micromoment activities, i.e., “Question Frenzy”, “Make It Relevant”, and “How Do We Make It Better?” that are linked, respectively, to the curiosity, connections, and creating value elements of EM were deployed in the class in the context of the use of a Corsi Rosenthal cube (a do-it-yourself structure that has recently become popular as an inexpensive way to reduce indoor particle pollution). Students generated concept maps pre-and post- micromoment intervention using the freely available CMap Tools software. The …

Utilization Of Iron Fillings Solid Waste For Optimum Biodiesel Production, Fady Ihab Bayoumy Eng., Ahmed Osman Ahmed Dr., David W. Rooney Dr., Mai H. Roushdy

Chemical Engineering

This study explores the innovative application of iron filings solid waste, a byproduct from mechanical workshops, as a heterogeneous catalyst in the production of biodiesel from waste cooking oil. Focusing on sustainability and waste valorization, the research presents a dual-benefit approach: addressing the environmental issue of solid waste disposal while contributing to the renewable energy sector. Particle size distribution analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray fluorescence (XRF), Thermal analysis (TG-DTA), and FTIR analysis were used to characterize the iron filings. The response surface methodology (RSM) was used to guide a series of experiments that were conducted to …

Valorisation Of Water Hyacinth For Different Engineering Applications, Nessren Farrag, Zeinab Elbhnsawi, Omar Aboelazayem

Chemical Engineering

Nature has many elements that can be beneficial or harmful. One of these elements is water hyacinth (WH) which is an aquatic weed found in water bodies such as rivers and lakes and it has an invasive nature due to its rapid growth rate. On the contrary, water hyacinth, despite its classification as an invasive plant species, possesses a multitude of industrial and engineering applications, demonstrating substantial potential for valorisation into various products. Its versatile attributes and widespread availability render water hyacinth a viable resource for deployment across several sectors, including wastewater treatment, bioenergy generation, bioremediation, and sustainable agriculture. The …

Experimental Thermal Conductivity Studies Of Agar-Based Aqueous Suspensions With Lignin Magnetic Nanocomposites, Bishal Gautam, Saja M. Nabat Al-Ajrash, Mohammad Jahid Hasan, Abhishek Saini, Sarah J. Watzman, Esteban Ureña-Benavides, Erick S. Vasquez-Guardado

Chemical and Materials Engineering Faculty Publications

Nanoparticle additives increase the thermal conductivity of conventional heat transfer fluids at low concentrations, which leads to improved heat transfer fluids and processes. This study investigates lignin-coated magnetic nanocomposites (lignin@Fe₃O₄) as a novel bio-based magnetic nanoparticle additive to enhance the thermal conductivity of aqueous-based fluids. Kraft lignin was used to encapsulate the Fe₃O₄ nanoparticles to prevent agglomeration and oxidation of the magnetic nanoparticles. Lignin@Fe₃O₄ nanoparticles were prepared using a pH-driven co-precipitation method with a 3:1 lignin to magnetite ratio and characterized by X-ray diffraction, FT-IR, thermogravimetric analysis, and transmission electron …

Machine-Learning-Assisted Design Of Deep Eutectic Solvents Based On Uncovered Hydrogen Bond Patterns, Usman Lame Abbas, Yuxuan Zhang, Joseph Tapia, Md Selim, Jin Chen, Jian Shi, Qing Shao

Markey Cancer Center Faculty Publications

Non-ionic deep eutectic solvents (DESs) are non-ionic designer solvents with various applications in catalysis, extraction, carbon capture, and pharmaceuticals. However, discovering new DES candidates is challenging due to a lack of efficient tools that accurately predict DES formation. The search for DES relies heavily on intuition or trial-and-error processes, leading to low success rates or missed opportuni- ties. Recognizing that hydrogen bonds (HBs) play a central role in DES formation, we aim to identify HB features that distinguish DES from non-DES systems and use them to develop machine learning (ML) models to discover new DES systems. We first analyze the …

Design And Characterization Of A Novel Eef2k Degrader With Potent Therapeutic Efficacy Against Triple-Negative Breast Cancer, Changxin Zhong, Rongfeng Zhu, Ting Jiang, Sheng Tian, Xiaobao Zhao, Xiaoya Wan, Shilong Jiang, Zonglin Chen, Rong Gong, Linhao He, Jin-Ming Yang, Na Ye, Yan Cheng

Markey Cancer Center Faculty Publications

Dysregulated eEF2K expression is implicated in the pathogenesis of many human cancers, including triple-negative breast cancer (TNBC), making it a plausible therapeutic target. However, specific eEF2K inhibitors with potent anti-cancer activity have not been available so far. Targeted protein degradation has emerged as a new strategy for drug discovery. In this study, a novel small molecule chemical is designed and synthesized, named as compound C1, which shows potent activity in degrading eEF2K. C1 selectively binds to F8, L10, R144, C146, E229, and Y236 of the eEF2K protein and promotes its proteasomal degradation by increasing the interaction between eEF2K and the …

Novel Castor Oil/Water/Ethanol Pickering Emulsions Stabilized By Magnetic Nanoparticles And Magnetically Controllable Demulsification, Mohammad J. Hasan, Peng Chen, Neithan Dominick, Erick S. Vasquez, Esteban E. Ureña-Benavides

Chemical and Materials Engineering Faculty Publications

A novel castor oil/water/ethanol Pickering emulsion, stabilized by magnetic nanoparticles (NPs), was developed to allow on-demand demulsification by an external magnetic field for the extraction of ethanol from aqueous solution using the castor oil. The emulsion was stabilized by Fe3O4-coated cellulose nanocrystals (CNC@Fe3O4) and lignin-coated Fe3O4 NPs (lignin@Fe3O4). The stability of the emulsions was investigated at various castor oil to ethanol-water ratios (50/50 and 70/30), various NP concentrations, and ethanol concentrations in the aqueous phase. The magnetically controlled demulsification ability of the emulsions was investigated by using a permanent magnet. The results showed that the 70/30 emulsions were more stable …