Other Chemical Engineering Commons^™

Signaling Pathways Activated By Interleukin-2 And Interluekin-4 Receptors Mediate T Lymphocyte Clonal Expansion, Kristen K. Comfort

Chemical and Materials Engineering Faculty Publications

Cells sense and respond to chemical and physical stimuli through signal transduction pathways, which mediate cell proliferation, differentiation, migration, and survival. The cytokines interleukin-2 (IL-2) and interleukin-4 (IL-4) are key regulators of the adaptive immune system, particularly influencing the clonal expansion and differentiation of T cells. At least in culture, both synergistic and antagonistic effects of IL-2 and IL-4 co-stimulation have been reported; the antagonism, when observed, is thought to arise from the utilization of a common subunit shared by IL-2 and IL-4 receptors. We have sought to characterize IL-2 and IL-4 signaling at the level of intracellular pathways activated …

Thermal Conductivity Improvement In Carbon Nanoparticle Doped Pao Oil: An Experimental Study, Shadab Shaikh, Khalid Lafdi, Rengasamy Ponnappan

Chemical and Materials Engineering Faculty Publications

The present work involves a study on the thermal conductivity of nanoparticle-oil suspensions for three types of nanoparticles, namely, carbon nanotubes(CNTs), exfoliated graphite (EXG), and heat treated nanofibers (HTT) with PAO oil as the base fluid. To accomplish the above task, an experimental analysis is performed using a modern light flash technique (LFA 447) for measuring the thermal conductivity of the three types of nanofluids, for different loading of nanoparticles.

The experimental results show a similar trend as observed in literature for nanofluids with a maximum enhancement of approximately 161% obtained for the CNT-PAO oil suspension. The overall percent enhancements …

Experimental Study On The Influence Of Foam Porosity And Pore Size On The Melting Of Phase Change Materials, Khalid Lafdi, Osama Mesalam Mesalhy, Shadab Shaikh

Chemical and Materials Engineering Faculty Publications

Experimental study was carried out to study the phase change heat transfer within a composite of phase change material (PCM) infiltrated high thermal conductivity foam. An experimental setup was built to measure the temperature profiles and capture the melting evolution of the PCM inside aluminum foams. Aluminum foams were used as the porous material, and low melting temperature paraffin wax was used as the PCM. It was observed from the results that the system parameters of the wax/foam composite had a significant influence on its heat transfer behavior.

By using higher porosity aluminum foam, the steady-state temperature was reached faster …

Effect Of Carbon Nanofiber Heat Treatment On Physical Properties Of Polymeric Nanocomposites—Part I, Khalid Lafdi, William Fox, Matthew Matzek, Emel Yildiz

Chemical and Materials Engineering Faculty Publications

The definition of a nanocomposite material has broadened significantly to encompass a large variety of systems made of dissimilar components and mixed at the nanometer scale. The properties of nanocomposite materials also depend on the morphology, crystallinity, and interfacial characteristics of the individual constituents. In the current work, vapor-grown carbon nanofibers were subjected to varying heat-treatment temperatures.

The strength of adhesion between the nanofiber and an epoxy (thermoset) matrix was characterized by the flexural strength and modulus. Heat treatment to 1800C∘ demonstrated maximum improvement in mechanical properties over that of the neat resin, while heat-treatment to higher temperatures demonstrated a …

Interfacial And Capillary Pressure Effects On The Thermal Performance Of Wax/Foam Composites, Mohammad Rajab Almajali, Khalid Lafdi, Shadab Shaikh

Chemical and Materials Engineering Faculty Publications

A numerical investigation study was performed to study the phase change behavior of wax/foam composite encapsulated in an aluminum casing. Two types of foam materials, namely, aluminum and carbon, were infiltrated with paraffin wax. The progress of melt interface and temperature distribution within the encapsulated composite was analyzed using computational fluid dynamics software (CFD). A two-energy equation model was implemented in the CFD software through the use of user-defined function (UDF). Interfacial effects influencing the heat transfer process at the casing-composite junction and between the wax-foam surfaces within the composite were addressed through the use of separate UDF. In addition, …

Oxygen Plasma Treatment And Deposition Of Cnx On A Fluorinated Polymer Matrix Composite For Improved Erosion Resistance, Christopher Muratore, Andras Korenyi-Both, John E. Bultman, A. R. Waite, John G. Jones, T. M. Storage, Andrey A. Voevodin

Chemical and Materials Engineering Faculty Publications

The use of polymer matrix composites in aerospace propulsion applications is currently limited by insufficient resistance to erosion by abrasive media. Erosion resistant coatings may provide necessary protection; however, adhesion to many high temperature polymer matrix composite (PMC) materials is poor. A low pressure oxygen plasma treatment process was developed to improve adhesion of CNx coatings to a carbon reinforced, fluorinated polymer matrix composite. Fullerene-like CNx was selected as an erosion resistant coating for its high hardness-to-elastic modulus ratio and elastic resilience which were expected to reduce erosion from media incident at different angles (normal or glancing) relative to the …

Accelerated Testing Method For Pem Fuel Cell Based Uninterrupted Power Supply Systems, Xinyu Huang, Xiaofeng Wang

Faculty Publications

Proton exchange membrane fuel cell based power systems are on the verge of commercialization for a number of niche applications where batteries are traditionally used. Uninterrupted power supply (UPS) for wireless communication towers and broadband network relay utilities is one of the targeted application of fuel cell power systems with capacity ranging from one to serveral kilowatts. It is believed that fuel cell based UPS systems can offer considerable advantage when extended backup time is desirable. In order to replace the well-known battery based UPS systems, the reliability and perofrmance of fuel cell based UPS system need to be thoroughly …

Demonstration Of Magnetoelectric Scanning Probe Microscopy, Jason R. Hattrick-Simpers, Liyang Dai, Manfred Wuttig, Ichiro Takeuchi, Eckhard Quandt

Faculty Publications

A near-field room temperature scanning magnetic probe microscope has been developed using a laminated magnetoelectric sensor. The simple trilayer longitudinal-transverse mode sensor, fabricated using Metglas as the magnetostrictive layer and polyvinylidene fluoride as the piezoelectric layer, shows an ac field sensitivity of 467±3μV∕O_e in the measured frequency range of 200Hz–8kHz. The microscope was used to image a 2mm diameter ring carrying an ac current as low as 10⁻⁵A. ac fields as small as 3×10⁻¹⁰T have been detected.

Rapid Structural Mapping Of Ternary Metallic Alloy Systems Using The Combinatorial Approach And Cluster Analysis, C. J. Long, Jason R. Hattrick-Simpers, M. Murakami, R. C. Srivastava, I. Takeuchi, V. L. Karen, X. Li

Faculty Publications

We are developing a procedure for the quick identification of structural phases in thin film composition spread experiments which map large fractions of compositional phase diagrams of ternary metallic alloy systems. An in-house scanning x-ray microdiffractometer is used to obtain x-ray spectra from 273 different compositions on a single composition spread library. A cluster analysissoftware is then used to sort the spectra into groups in order to rapidly discover the distribution of phases on the ternary diagram. The most representative pattern of each group is then compared to a database of known structures to identify known phases. Using this method, …

Simulation Of Polarization Curves For Oxygen Reduction Reaction In 0.5 M H2So4 At A Rotating Ring Disk Electrode, Qingbo Dong, Shriram Santhanagopalan, Ralph E. White

Faculty Publications

A cylindrical two-dimensional model based on the Nernst–Planck equations, the Navier–Stokes equation, and the continuity equation is used to simulate the oxygen reduction reaction in 0.5MH₂SO₄ at a rotating ring disk electrode. Concentration distributions and a potential profile are obtained as a function of the axial and radial distances from the center of the electrode surface. Polarization curves are simulated to interpret experimental results by studying various reaction mechanisms, i.e., the four-electron-transfer reduction of oxygen, the two-electron-transfer reduction of oxygen, a combination of the above two reactions, mechanisms with reduction of peroxide to water, and/or the heterogeneous …

Moving Boundary Model For The Discharge Of A Licoo2 Electrode, Qi Zhang, Ralph E. White

Faculty Publications

A moving boundary model in a spherical LiCoO₂ particle is presented to account for the diffusion controlled phase transition in LiCoO₂ solid particles, and this model is incorporated into a porous electrode model for the LiCoO₂ electrode. The simulation results agree well with the experimental data of a LiCoO₂ electrode. A study of the flux distribution in the porous electrode shows that the phase transition phenomenon in the LiCoO₂particles has a significant effect on the flux distribution by changing the solid phase diffusion resistance in the particles.