Open Access. Powered by Scholars. Published by Universities.®

Aerospace Engineering Commons™

Open Access. Powered by Scholars. Published by Universities.®

Discipline
Institution
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 9361 - 9390 of 11199

Full-Text Articles in Aerospace Engineering

Cycle Performance Of A Pulse Detonation Engine With Supercritical Fuel Injection, Timothy M. Helfrich Mar 2006

Cycle Performance Of A Pulse Detonation Engine With Supercritical Fuel Injection, Timothy M. Helfrich

Theses and Dissertations

Pulse detonation engines (PDE) rely on rapid ignition and formation of detonation waves. Because hydrocarbon fuels are composed typically of long carbon chains that must be reduced in the combustion process, it would be beneficial to create such reduction prior to injection of fuel into the engine. This study focused on PDE operation enhancements using dual detonation tube, concentric-counter-flow heat exchangers to elevate the fuel temperature up to supercritical temperatures. Variation of several operating parameters included fuel type (JP-8, JP-7, JP-10, RP-1, JP-900, and S-8), ignition delay, frequency, internal spiral length, and purge fraction. To quantify the performance, four key …

Go to article

Optimization Of A Low Heat Load Turbine Nozzle Guide Vane, Jamie J. Johnson Mar 2006

Optimization Of A Low Heat Load Turbine Nozzle Guide Vane, Jamie J. Johnson

Theses and Dissertations

Often turbomachinery airfoils are designed with aerodynamic performance foremost in mind rather than component durability. However, future aircraft systems require ever increasing levels of gas-turbine inlet temperature causing the durability and reliability of turbine components to be an ever more important design concern. As a result, the need to provide improved heat transfer prediction and optimization methods presents itself. Here, an effort to design an airfoil with minimized heat load is reported. First, a Reynolds-Averaged Navier-Stokes (RANS) flow solver was validated over different flow regimes as well as varying boundary conditions against extensive data available in literature published by the …

Go to article

Spatially-Resolved Temperature Diagnostic For Supersonic Flow Using Cross-Beam Doppler-Limited Laser Saturation Spectroscopy, Grady T. Phillips Mar 2006

Spatially-Resolved Temperature Diagnostic For Supersonic Flow Using Cross-Beam Doppler-Limited Laser Saturation Spectroscopy, Grady T. Phillips

Theses and Dissertations

Optical techniques for measuring the temperature in three-dimensional supersonic reactive flows have typically depended on lineshape measurements using single-beam laser absorption spectroscopy. However, absorption over extended path lengths in flows with symmetric, turbulent eddies can lead to systematically high extracted temperatures due to Doppler shifts resulting from flow along the absorption path. To eliminate these problems, Cross-Beam Saturation Absorption Spectroscopy (CBSAS) and Cross-Beam Inter-Modulated Fluorescence (CBIMF) have been developed which utilize two crossed and nearly copropogating laser beams.to record the spectral signal of an I2 ro-vibrational line in a small three-dimensional volume using a tunable CW dye laser. Temperature …

Go to article

Evaluating The Correlation Characteristics Of Arbitrary Am And Fm Radio Signals For The Purpose Of Navigation, Bryan S. Kim Mar 2006

Evaluating The Correlation Characteristics Of Arbitrary Am And Fm Radio Signals For The Purpose Of Navigation, Bryan S. Kim

Theses and Dissertations

The Global Positioning System (GPS) provides position estimates on the Earth at anytime, anywhere and in any weather. However, to provide robust positioning, GPS requires an unobstructed path to satellite signals. As such, GPS performance generally degrades or becomes non-existent in environments such as large urban areas. This research investigates and analyzes the correlation characteristics of arbitrary AM and FM radio signals for the purpose of navigation. Simulations are conducted with different combinations of correlation methods (`fixed' or `varying'), modulation types (AM or FM), and signal types (song or voice). Out of the eight different variations considered, only two provided …

Go to article

Performance Analysis Of A Cooperative Search Algorithm For Multiple Unmanned Aerial Vehicles Under Limited Communication Conditions, Kevin M. Morris Mar 2006

Performance Analysis Of A Cooperative Search Algorithm For Multiple Unmanned Aerial Vehicles Under Limited Communication Conditions, Kevin M. Morris

Theses and Dissertations

This research investigates the impacts of realistic wireless communications upon a group of unmanned aerial vehicles (UAVs) utilizing a distributed search algorithm. The UAVs are used to survey an area for mobile targets and they require communication to cooperatively locate the targets. The mobile targets do not continually radiate energy, which exacerbates the search effort; a UAV could fly directly over a target and not detect it. A simulation of cooperative UAVs is implemented using the OPNET Modeler network simulation tool. The search performance of a group of UAVs is observed when communication range, data rate, and the number of …

Go to article

Estimation And Mitigation Of Unmodeled Errors For A Pseudolite Based Reference System, Jeremiah A. Shockley Mar 2006

Estimation And Mitigation Of Unmodeled Errors For A Pseudolite Based Reference System, Jeremiah A. Shockley

Theses and Dissertations

Current flight reference systems rely heavily on the Global Positioning System (GPS), causing susceptibility to GPS jamming. Additionally, an increasing number of tests involve jamming the GPS signal. A need exists to develop a system capable of GPS-level accuracy during these outages. One promising solution is a ground-based pseudolite system capable of delivering sub-centimeter level accuracy, yet operating at non-GPS frequencies. This thesis attempts to determine the unknown errors in the Locata system, one such pseudolite-based system, to achieve the accuracy required. The development of a measurement simulation tool along with a Kalman filter algorithm provides confirmation of filter performance …

Go to article

Development And Testing Of An Inflatable, Rigidizable Space Structure Experiment, Sarah K. Helms Mar 2006

Development And Testing Of An Inflatable, Rigidizable Space Structure Experiment, Sarah K. Helms

Theses and Dissertations

Many recent space technology concepts require large space structures such as solar arrays and large aperture antennas; however, tight constraints on payload mass and volume often preclude their launch. Employing inflatable, rigidizable structures can reduce mass and volume while providing sufficient packing flexibility and structural stiffness. AFIT has developed RIGEX to flight-test this type of structure. RIGEX will test the deployment and structural characteristics of three thermoplastic composite Sub-Tg tubes. Once launched on the Space Shuttle in 2007, the spaceflight results will be compared to lab data to validate on-orbit reliability and ground test methods. This paper documents three main …

Go to article

Evaluation Of Factors Contributing To Damping Of Coated And Uncoated Titanium Plates, Dustin W. Lee Mar 2006

Evaluation Of Factors Contributing To Damping Of Coated And Uncoated Titanium Plates, Dustin W. Lee

Theses and Dissertations

High Cycle Fatigue (HCF) is the leading cause of component failure in gas turbine engines today, which poses great risk to aircraft, engines, and their crews. Mitigation of HCF effects has become a priority topic, and the damping benefits of hard coatings are being reevaluated for this purpose. Research was conducted to further understanding of damping measurements on these coatings. This study continues work to characterize the damping effects of a magnesium aluminate spinel (mag spinel) coating applied to a titanium plate via vibration testing. Two different plate sizes were evaluated in a clamped-free-free-free condition and a free-free-free-free condition, respectively. …

Go to article

Optimal Coverage Of Theater Targets With Small Satellite Constellations, Axel Rendon Mar 2006

Optimal Coverage Of Theater Targets With Small Satellite Constellations, Axel Rendon

Theses and Dissertations

The daylight passes of a low-Earth orbit satellite over a targeted latitude and longitude are optimized by varying the inclination and eccentricity of an orbit at different altitudes. This investigation extends the work by Emery et al, in which the optimal Right Ascension of the Ascending Node was determined for a circular, matched inclination orbit. The optimal values were determined by a numerical research method based on Emery et al's Matlab program. Results indicate that small increases in inclination raise the number of daylight passes up to 33%. These optimal inclinations depend on the satellite semi-major axis. Eccentricity increases also …

Go to article

Performance Capability Of A Damaged Lighter-Than-Air Vehicle Operating In The Near Space Regime, Charles W. Vogt Jr. Mar 2006

Performance Capability Of A Damaged Lighter-Than-Air Vehicle Operating In The Near Space Regime, Charles W. Vogt Jr.

Theses and Dissertations

This study investigates the ability of a high-altitude airship to maintain lift following the compromise of its lifting gas envelope. Accepted engineering principles are applied to develop a model that provides comparative analyses for airship depressurization alternatives following hull compromise. Specifically, maintaining lifting gas envelope overpressure to provide controllability in wind currents while sacrificing some buoyancy is compared with allowing envelope depressurization to occur with the goal of maintaining greater buoyancy as long as possible. The model provides insights to alternatives for recovering a damaged vehicle and its payload. In particular, the analysis demonstrates that maintaining the ability to navigate …

Go to article

Comparative Analysis Of Two-Stage-To-Orbit Rocket And Airbreathing Reusable Launch Vehicles For Military Applications, Joseph M. Hank Mar 2006

Comparative Analysis Of Two-Stage-To-Orbit Rocket And Airbreathing Reusable Launch Vehicles For Military Applications, Joseph M. Hank

Theses and Dissertations

The Department of Defense (DoD) has identified operationally responsive, low-cost access to space as vital to maintaining U.S. military supremacy. Reusable Launch Vehicles (RLVs) will allow the U.S. to keep a technological advantage over our adversaries, and advances in airbreathing propulsion technology have made it feasible for use in space launch vehicles. This study considers two-stage-to-orbit (TSTO) RLV configurations, each using combinations of propulsion including pure rocket, pure turbine, rocket-based-combined-cycle (RBCC), and turbine-based-combined-cycle (TBCC) for the both stages. This study explores the advantages of airbreathing propulsion in those key areas when compared to a baseline configuration, using vehicle empty mass …

Go to article

Simulation Of A Moving Elastic Beam Using Hamilton's Weak Principle, Elliott J. Leigh Mar 2006

Simulation Of A Moving Elastic Beam Using Hamilton's Weak Principle, Elliott J. Leigh

Theses and Dissertations

Hamilton's Law is derived in weak form for slender beams with closed cross sections. The result is discretized with mixed space-time finite elements to yield a system of nonlinear, algebraic equations. An algorithm is proposed for solving these equations using unconstrained optimization techniques, obtaining steady-state and time accurate solutions for problems of structural dynamics. This technique provides accurate solutions for nonlinear static and steady-state problems including the cantilevered elastica and flatwise rotation of beams. Modal analysis of beams and rods is investigated to accurately determine fundamental frequencies of vibration, and the simulation of simple maneuvers is demonstrated.

Go to article

Characterization Of Pulse Detonation Engine Performance With Varying Free Stream Stagnation Pressure Levels, Wesley R. Knick Mar 2006

Characterization Of Pulse Detonation Engine Performance With Varying Free Stream Stagnation Pressure Levels, Wesley R. Knick

Theses and Dissertations

A pulse detonation engine operates on the principle that a fuel-air mixture injected into a tube will ignite and undergo a transition from a deflagration to a detonation and exit the tube at supersonic velocities. Studies in the field of combustion have shown that both ignition time and deflagration to detonation transition time can vary as a function of pressure. It can be hypothesized that if ignition and deflagration to detonation transition times can be reduced by increasing the free stream stagnation pressure level of the tube, it would then be possible to shorten the detonation tube length and increase …

Go to article

Quantitative Analysis Of A Turbulent Wind Tunnel With Obstructions For Use In Liquid Flame Spread Experiments, Beau M. Brantley Mar 2006

Quantitative Analysis Of A Turbulent Wind Tunnel With Obstructions For Use In Liquid Flame Spread Experiments, Beau M. Brantley

Theses and Dissertations

The research was done as part of an effort to develop alternative fire suppressant technologies for aircraft engine nacelles. The turbulent shear flow behind a surface mounted fence inside an open circuit wind tunnel was investigated experimentally. The tunnel test section was designed to be 2-D and exhibit flow qualities similar to those found in a typical engine nacelle. A 279 mm wide fuel pan was inserted approximately four fence heights downstream of the fence location. The fuel pan was filled using water to simulate fuel with a depth of 32 mm. Cold flow tests were done on different fence …

Go to article

Formation Flight Control For Aerial Refueling, Steven M. Ross Mar 2006

Formation Flight Control For Aerial Refueling, Steven M. Ross

Theses and Dissertations

A controller is designed for an aircraft to autonomously fly formation during aerial refueling. Requirements for a refueling autopilot are stated. A six-degree-of-freedom model is developed for an F-16 lead aircraft and a Learjet LJ-25 wing aircraft. Bare airframe stability of both aircraft is investigated, and stability augmentation is performed. A Matlab Simulink® simulation is built to reproduce the sensor inputs that will be available to the wing aircraft in flight, including disturbances. Control frames are investigated to determine the optimum presentation of the error vector for control during the task of air refueling. Control laws are developed from the …

Go to article

Fretting Fatigue Behavior Of Shot-Peened In 100, Jonathan L. Ng Mar 2006

Fretting Fatigue Behavior Of Shot-Peened In 100, Jonathan L. Ng

Theses and Dissertations

The fretting fatigue behavior of shot-peened of IN 100 was investigated in this study. S-N curves were obtained for two different shot-peened intensities (7A and 12A) and were compared to those of unpeened specimens. Stress relaxation behavior under fretting fatigue was also investigated after their measurements were obtained using the X-ray diffraction method. The crack initiation location and the crack angle orientation along the surface were determined using optical and scanning electron microscopy (SEM). Cracks initiated near the trailing edge and on the contact surface for both 7A and 12A shot-peened specimens. Finite element analysis was performed using commercially available …

Go to article

Experimental Investigation Into The Aerodynamic Ground Effect Of A Tailless Chevron And Lambda-Shaped Ucavs, Won In Mar 2006

Experimental Investigation Into The Aerodynamic Ground Effect Of A Tailless Chevron And Lambda-Shaped Ucavs, Won In

Theses and Dissertations

As future aircraft migrate toward tailless, blended wing body configurations, aircraft designers are faced with a lack of experimental data that represent these types of configurations. A wind tunnel investigation was conducted to identify the ground effect region of two unmanned combat air vehicle (UCAV) models. The AFIT low-speed wind tunnel (LSWT) and ground plane were used to study the forces and moments on the UCAV models in ground effect. The Chevron and Lambda planforms used in this study were originally tested in full-scale for stability and control without ground effects. A static ground plane was used in this study. …

Go to article

Store Separations From A Supersonic Cone, Richard J. Simko Mar 2006

Store Separations From A Supersonic Cone, Richard J. Simko

Theses and Dissertations

The purpose of this research was to analyze the environment a store would travel through if ejected from a supersonic cone. This was done using the Beggar Computational Fluid Dynamics (CFD) code from the Air Force SEEK Eagle Office at Eglin Air Force Base, FL. CFD simulations were compared to experimental results from a previous AFIT thesis and conclusions were drawn based on whether or not the current wind tunnel setup at AFIT is capable of performing analyses of supersonic store separations. Also included in this research is a study of supersonic base pressure profiles, near-wake velocity profiles, wind tunnel …

Go to article

Cfd Investigation Of The Flow Dynamics Inside A Spherical Surface Indentation, Robert C. Vincent Mar 2006

Cfd Investigation Of The Flow Dynamics Inside A Spherical Surface Indentation, Robert C. Vincent

Theses and Dissertations

This study aims to identify the flow structure inside and around a dimple surface indentation that passively reduces flow separation, and to generate characterization parameters for the effectiveness of the aforementioned flow structure in boundary layer separation control. In this study the surface indentation is cut into a flat plate in a diverging channel that creates an adverse pressure gradient. In the baseline flat plate conditions, the shedding vortices formed by the pressure gradient create an oscillating pressure field in the dimple. This geometry has been chosen to simulate the adverse pressure gradient present in the flow regime found on …

Go to article

Methods For Aiding Height Determination In Pseudolite-Based Reference Systems Using Batch Least-Squares Estimation, John H. R. Amt Mar 2006

Methods For Aiding Height Determination In Pseudolite-Based Reference Systems Using Batch Least-Squares Estimation, John H. R. Amt

Theses and Dissertations

There are many situations in which GPS is either unable to provide the desired level of accuracy or is unavailable. Use of a pseudolite-based reference system for navigation can be a means for positioning during these times. While there are advantages in using a pseudolite-based reference system, there are still implementation issues and deficiencies that must be addressed. In many cases, a pseudolite system with ground-based transmitters has difficulty determining the height of the receiver accurately. This is due to the poor vertical observability inherent in the geometry of the system. A common approach in naval applications for solving the …

Go to article

Free Flight Store Simulation Using Beggar, Judson T. Babcock Mar 2006

Free Flight Store Simulation Using Beggar, Judson T. Babcock

Theses and Dissertations

The complete numerical solution of the airflow around a store in extended free flight is of particular importance to the United States Air Force. Beggar is the primary Computational Fluid Dynamics (CFD) program used by the USAF to obtain solutions for store separations. However, Beggar's ability to simulate a store in free flight is limited because the store must fall through a static background mesh, eventually reaching a point where the solution will fail. The length of any free flight simulation is consequently limited by the height of the background mesh. Code modifications are made to Beggar to remove this …

Go to article

Space-Time Adaptive Processing For Side-Looking Arrays With Platform Maneuver, John T. Buckreis Mar 2006

Space-Time Adaptive Processing For Side-Looking Arrays With Platform Maneuver, John T. Buckreis

Theses and Dissertations

This research effort develops a space-time adaptive processing (STAP) radar data model for the side-looking (SL) array with platform maneuver. A primary assumption of most STAP models is the absence of platform maneuver during the coherent processing interval (CPI). This research abandons the platform stationarity assumption, allowing platform pitch, roll, and yaw during the CPI. The model developed characterizes platform maneuver effects on the clutter spectrum, examines Matched Filter (MF) output Signal-to-Interference-plus-Noise-Ratio (SINR), and investigates maneuver impact on sample support homogeneity. The introduction of pitch marginally impacts MF SINR due to the lack of achieved azimuth resolution in this research, …

Go to article

Characterization Of Functionally Graded Materials, Benjamin D. Chapman Mar 2006

Characterization Of Functionally Graded Materials, Benjamin D. Chapman

Theses and Dissertations

The purpose of this study was to characterize the behavior of a functionally graded material through experimentation and analytical modeling. Functionally graded materials are a ceramic metal composite which transitions from metal on one face to ceramic on the opposite face. Creating reliable models required verifying the material properties. This was accomplished through the use of a static modulus of elasticity test as well as a dynamic ping test. The natural frequencies from the dynamic test were compared with finite element models to determine which material properties most accurately represented the functionally graded material. It was found that the material …

Go to article

Optimizing Mean Mission Duration For Multiple-Payload Satellites, John A. Flory Mar 2006

Optimizing Mean Mission Duration For Multiple-Payload Satellites, John A. Flory

Theses and Dissertations

This thesis addresses the problem of optimally selecting and specifying satellite payloads for inclusion on a satellite bus to be launched into a constellation. The objective is to select and specify payloads so that the total lifetime utility of the constellation is maximized. The satellite bus is limited by finite power, weight, volume, and cost constraints. This problem is modeled as a classical knapsack problem in one and multiple dimensions, and dynamic programming and binary integer programming formulations are provided to solve the problem. Due to the computational complexity of the problem, the solution techniques include exact methods as well …

Go to article

Detailed Design Of The Rigidizable Inflatable Get-Away-Special Experiment, Jeremy S. Goodwin Mar 2006

Detailed Design Of The Rigidizable Inflatable Get-Away-Special Experiment, Jeremy S. Goodwin

Theses and Dissertations

The Rigidizable Inflatable Get-Away-Special Experiment is a Space Shuttle experiment that will study the effects of the zero-gravity space environment on the deployment and modal analysis of three inflatable and rigidizable tubes using a sub-Tg rigidization technique. In 2004, RIGEX was transitioned from the Space Shuttle's Get-Away-Special (GAS) canister to its Canister for All Payload Ejections (CAPE), requiring several modifications to the design. The results of these modifications, along with further refinements made to previous efforts, combine to form the detailed design of the experiment. In addition to the design modifications, analyses were conducted to determine the containment capabilities of …

Go to article

Bio-Inspired, Odor-Based Navigation, Maynard John Porter Iii Mar 2006

Bio-Inspired, Odor-Based Navigation, Maynard John Porter Iii

Theses and Dissertations

The ability of moths to locate a member of the opposite sex, by tracking a wind-borne plume of odor molecules, is an amazing reality. Numerous scenarios exist where having this capability embedded into ground-based or aerial vehicles would be invaluable. The main crux of this thesis investigation is the development of a navigation algorithm which gives a UAV the ability to track a chemical plume to its source. Inspiration from the male moth's, in particular Manduca sexta, ability to successfully track a female's pheromone plume was used in the design of both 2-D and 3-D navigation algorithms. The algorithms were …

Go to article

Creep-Rupture Behavior Of A Woven Ceramic Matrix Composite At Elevated Temperatures In A Humid Environment, Jennifer L. Ryba Mar 2006

Creep-Rupture Behavior Of A Woven Ceramic Matrix Composite At Elevated Temperatures In A Humid Environment, Jennifer L. Ryba

Theses and Dissertations

This study focused on moisture and temperature effects on the embrittlement and stress-rupture life of the SiC/SiC CMC Syl-iBN/BN/SiC. The Syl-iBN/BN/SiC is composed of Sylramic fibers with an in-situ layer of boron nitride (Syl-iBN), boron nitride interphase (BN), and SiC matrix. Stress rupture tests and monotonic tests were performed on the specimens. Tests were conducted under 100% humidity and laboratory air environments at three temperatures, 450°C, 750°C, and 950°C. These temperatures were chosen because they fall below the intermediate range, within the range, and above the range, respectively. This study found that while this CMC does experience embrittlement at intermediate …

Go to article

Covariance Estimation And Autocorrelation Of Norad Two-Line Element Sets, Victor P. Osweiler Mar 2006

Covariance Estimation And Autocorrelation Of Norad Two-Line Element Sets, Victor P. Osweiler

Theses and Dissertations

This thesis investigates NORAD two-line element sets (TLE) containing satellite mean orbital elements for the purpose of estimating a covariance matrix and formulating an autocorrelation relationship. Orbit propagation is performed using Simplified General Perturbations Number 4 (SGP4) analytical model as implemented within Satellite Took Kit. For a given satellite, TLEs from a span of two weeks are used to calculate position and velocity differences of estimated state vectors in order to characterize their variance behavior and compute a covariance matrix for the most recent TLE. Six satellites and eight time spans are investigated, with all state vector differences evaluated in …

Go to article

Control Demonstration Of A Thin Deformable In-Plane Actuated Mirror, Gina A. Peterson Mar 2006

Control Demonstration Of A Thin Deformable In-Plane Actuated Mirror, Gina A. Peterson

Theses and Dissertations

Current imaging satellites are limited in resolution and coverage area by the aperture size of their primary optical mirror. To get a large optical mirror into space, current launch weight and size restrictions must be overcome. Membrane-like optical mirrors can overcome these restrictions with their very lightweight and flexible properties. However, thin, deformable membrane mirrors are very susceptible to the space environment and require active control for surface stabilization and shaping. The primary goal of this research is to demonstrate that an in-plane actuated membrane-like deformable optical mirror can be controlled to optical wavelength tolerances in a closed-loop system. Fabrication …

Go to article

Design, Build And Validation Of A Small-Scale Combustion Chamber Testing Facility, Eric R. Dittman Mar 2006

Design, Build And Validation Of A Small-Scale Combustion Chamber Testing Facility, Eric R. Dittman

Theses and Dissertations

This study investigated the design parameters necessary for the construction and use of a testing facility built to test the combustor section of engines. User inputs were acquired by interview and used in the decisions made in arrangement of pieces of machinery and how different systems were to interact. The design was then carried out as the various parts of the facility were built and installed. Software was designed which controlled the different parts of the combustion process and monitored the different products of combustion as well as the properties of the air and fuel used in the combustion. These …

Go to article

First Prev Next Last