Aerospace Engineering Commons^™

Effects Of Cyclic Prefix Jamming Versus Noise Jamming In Ofdm Signals, Amber L. Scott

Theses and Dissertations

Signal jamming of an orthogonal frequency-division multiplexing (OFDM) signal is simulated in MATLAB. Two different means of jamming are used to see, which is a more efficient way to disrupt a signal using the same signal power. The first way is a basic additive white Gaussian noise (AWGN) jammer that equally jams the entire signal. The second way is an AWGN jammer that targets only the cyclic prefix (CP) of the signal. These two methods of jamming are simulated using different channel models and unknowns to get varying results. The three channel models used in the simulations are the no …

Airborne Wind Energy: Implementation And Design For The U.S. Air Force, Troy L. Cahoon

Theses and Dissertations

Excitement among researchers about Airborne Wind Energy (AWE) technology matches DoD aims to advance and employ renewable energy. AWE seeks to cost-effectively tap the vast supply of wind energy available at altitudes high above the reach of conventional, ground-based wind turbines (e.g. 500-12,000m). This paper explores viability and implementation of AWE technology for fulfilling USAF energy needs. Characteristics, potential, and developmental status of the AWE resource are presented. A design tool for a rotor-based AWE system is developed, facilitating the analysis of blade performance to simplify design and provide the best efficiencies for a range of conditions. USAF bases are …

Performance Characterization Of A Novel Plasma Thruster To Provide A Revolutionary Operationally Responsive Space Capability With Micro- And Nano-Satellites, John-David C. De La Harpe

Theses and Dissertations

Few options currently exist to provide propulsion for extremely small satellites due to design constraints on power, volume, and weight. However, future operation will require a capability to conduct orbital maneuvers, momentum dumping, and precision pointing for these low cost satellites. The research presented here represents the first effort to operate and quantify the performance of a new micro plasma thruster design which provides a novel solution to these disparate competing constraints. The thruster in this study represents a deviation from traditional circular Hall thruster design practices, because it eschews a central magnetic circuit, which results in nearly parallel electric …

Ch-47d Rotating System Fault Sensing For Condition Based Maintenance, Stephen M. Dickerson

Theses and Dissertations

The Department of Defense (DoD) has mandated the use of maintenance practices based on component condition rather than component time in service or age. This new practice is known as Condition Based Maintenance, and it relies on accurate detection and identification of material deficiencies in system components. Rotor system components in rotary-wing aircraft can be difficult to monitor due to the rotational environment experienced by the sensors and the difficulty of signal transmission. Current methods are able to detect the existence of a fault in the rotor system but cannot link the vibrations experienced in the airframe to a specific …

Vibration Interaction In A Multiple Flywheel System, Jordan A. Firth

Theses and Dissertations

This study uses a linear model of an Integrated Power and Attitude Control System (IPACS) to investigate the vibration interaction between multiple flywheels. An easily extendable Matlab® script is created for the analysis of flywheel vibrations. This script is used to build a vibration model consisting of two active magnetic bearing flywheels mounted on a support structure. The flywheels are rotated at varying speeds, with an imbalance-induced centripetal force in one or both wheels causing vibrations in both wheels. Flywheel and system responses are examined for low frequency vibrations which would cause undesirable excitation to a satellite using IPACS, with …

Kam Torus Frequency Generation From Two-Line Element Sets, Gregory R. Frey

Theses and Dissertations

The Kolmogorov Arnold and Moser (KAM) theorem states that a lightly perturbed Hamiltonian system will have solutions which lie on a torus. Earlier work by the second author has shown that most Earth satellite orbits perturbed by the geopotential lie on KAM tori. The problem then arises as to how to convert the current satellite tracking orbits to KAM tori. A KAM torus is characterized by three frequencies and three phase angles. The frequencies are essentially the rates of change of the mean anomaly, the longitude of the ascending node, and the argument of perigee. In this paper we explore …

Optimized Dual Expander Aerospike Rocket, Joshua N. Hall

Theses and Dissertations

Research at the Air Force Institute of Technology (AFIT) focused on designing a cryogenic dual-expander aerospike nozzle (DEAN) upper stage rocket engine to produce 50,000 pounds-force (222.4 kilo-Newtons) vacuum thrust, 464 seconds of vacuum specific impulse and a thrust-to-weight ratio of 106.5. The use of dual expander cycles improves engine reliability, maximizes efficiency, and eliminates some catastrophic failure modes. An upper stage engine with an aerospike nozzle is shorter and lighter than an equivalent performing conventional bell nozzle upper stage engine. Previous research focused on first developing a feasible closed DEAN design model and secondly expanding the model to support …

Revolutionizing Space Propulsion Through The Characterization Of Iodine As Fuel For Hall-Effect Thrusters, Adam C. Hillier

Theses and Dissertations

The demand for increased performance in space propulsion systems is higher than ever as missions are becoming more advanced. As the global supply of xenon depletes, missions demanding high thrust will require alternatives. The research presented here examines iodine as an alternate propellant. The propellant was successfully operated through a BHT-200 thruster in the T6 vacuum facility at Busek Co. Inc. A feed system for the iodine was developed for controlled thruster operation at varying conditions. An inverted pendulum was used to take thrust measurements. Thrust to power ratio, anode efficiency, and specific impulse were calculated. Iodine performance is compared …

Fixed-Wing Aircraft Combat Survivability Analysis For Operation Enduring Freedom And Operation Iraqi Freedom, Christopher L. Jerome

Theses and Dissertations

The primary tenet of the aircraft survivability discipline is threat definition. In order to deliver relevant capabilities and protection to the warfighter it is imperative; therefore, to provide timely, accurate, and actionable threat data to the survivability community. In an attempt to identify the evolution of aircraft threats in today's combat environment, an analysis of fixed-wing aircraft battle damage was conducted. This analysis reports battle damage incidents from OPERATIONS ENDURING FREEDOM (OEF) and IRAQI FREEDOM(OIF). Additionally, reported damage incidents were then validated by crosschecking aircraft maintenance records from this period to eliminate non-hostile fire data points. This revolutionary approach uncovered …

X-Hale: The Development Of A Research Platform For The Validation Of Nonlinear Aeroelastic Codes, Alexander A. Kaszynski

Theses and Dissertations

In conjunction with the Air Force Institute of Technology (AFIT) and the Air Force Research Laboratory (AFRL), the University of Michigan has designed and is currently building a remotely piloted aircraft (RPA) experimental high altitude long endurance (X-HALE) aircraft to collect non-linear aeroelastic data to validate HALE aircraft design codes developed by academia, industry, and the federal government. While X-HALE is representative of HALE aircraft, the manufacturing and evaluation techniques are applicable to larger full size HALE aircraft such as the concepts being developed under Defense Advanced Research Projects Agency's (DARPA's) Vulture program. This paper documents the development of the …

Follower-Force Experiments With Geometric Non-Linear Coupling For Analytical Validation, Tae H. Kim

Theses and Dissertations

This study was a follow-up of a previous study where static deflection data of a joined-wing test article was collected from a series of experiments using a laser scanner and a laser tracker while the test articles were subjected to follower-forces. One of the goals of this study was to collect accurate experimental data which could be used to validate analytical methods, such as geometrically exact beam theory, which are used to predict the nonlinear response of joined-wings. The load application system used on the previous study was not able to provide a follower-force on the test articles, and therefore …

Heat Transfer Experiments On A Pulse Detonation Driven Combustor, Nicholas C. Longo

Theses and Dissertations

Heat transfer experiments were conducted using a heat exchanger behind a pulse detonation combustor and a Garrett automotive turbocharger at the Air Force Research Lab (AFRL). The equivalence ratio and purge fraction were held at 1.0 and 0.9, respectively, while the frequency of operation was varied from 10 to 12 Hz in 1 Hz movements, and the fill fraction was varied from 0.5 to 0.8 in 0.1 increments. Temperature measurements were calculated using an energy balance allowing for the calculation of heat exchanger inlet enthalpy. The heat exchanger inlet enthalpy was estimated to be the exit enthalpy of the turbocharger …

Detonation Propagation Through Ducts In A Pulsed Detonation Engine, Jeffrey M. Nielsen

Theses and Dissertations

Development of a continuously operating pulsed detonation engine (PDE) without a high energy ignition system or a deflagration-to- detonation transition (DDT) device will increase engine efficiency, reduce cost, improve performance, and reduce weight. This report is a study of configurations that allow a consistent and predictable transition of a detonation from one detonation tube to second tube. The intent was, via visualization of detonation propagation through a cross-over tube, to develop a cross-over passage leading to minimization of energy losses and effective and repeatable tube-to-tube initiation. Detonation tube cross-over width, cross-over geometry and fuels were varied to determine their effect …

Flapping Wing Micro Air Vehicle Wing Manufacture And Force Testing, Nathanael J. Sladek

Theses and Dissertations

Numerous wing manufacturing techniques have been developed by various universities for research on Flapping Wing Micro Air Vehicles. Minimal attention though is given to repeatability of wing aerodynamics and dynamic response, which is crucial to avoid asymmetric flapping. Thus the focus of this research becomes twofold. First, repeatable wing manufacturing techniques are developed to ensure flapping wings have similar aerodynamic and dynamic characteristics. For this purpose, four wing designs were selected to not only test the aerodynamics of the different designs, but to also validate manufacturing techniques. The various wing designs are assessed using two methods: dynamic and aerodynamic data. …

Small Internal Combustion Engine Testing For A Hybrid-Electric Remotely-Piloted Aircraft, Isseyas H. Mengistu

Theses and Dissertations

Efficient operation of a hybrid-electric propulsion system (HEPS) powering a small remotely-piloted aircraft (RPA) requires that a controller have accurate and detailed engine and electric motor performance data. Many small internal combustion engines (ICEs) currently used on various small RPA were designed for use by the recreational hobbyist radio-control (R/C) aircraft market. Often, the manufacturers of these engines do not make accurate and reliable detailed engine performance data available for their engines. A dynamometer testing stand was assembled to test various small ICEs. These engines were tested with automotive unleaded gasoline (the manufacturer's recommended fuel) using the dynamometer setup. Torque, …

Two Dimensional Positioning And Heading Solution For Flying Vehicles Using A Line-Scanning Laser Radar (Ladar), Brady T. Christel

Theses and Dissertations

Emerging technology in small autonomous flying vehicles requires the systems to have a precise navigation solution in order to perform tasks. In many critical environments, such as indoors, GPS is unavailable necessitating the development of supplemental aiding sensors to determine precise position. This research investigates the use of a line scanning laser radar (LADAR) as a standalone two dimensional position and heading navigation solution and sets up the device for augmentation into existing navigation systems. A fast histogram correlation method is developed to operate in real-time on board the vehicle providing position and heading updates at a rate of 10 …

High Frequency Direction Finding Using Structurally Integrated Antennas On A Large Airborne Platform, Clair F. Corbin

Theses and Dissertations

Estimating the angle of arrival (AOA) of a high frequency (HF) signal, 2-32 MHz, is challenging, especially if the antenna array is installed on a platform with dimensions on the order of one wavelength. Accurate AOA estimates are necessary for search and rescue operations and geolocating RF emitters of interest. This research examines the performance of a direction finding (DF) system using structurally integrated (SI) antennas installed on an airborne platform which allows the aircraft structure to become the receiving element. Two simulated DF systems are analyzed at 4 and 11 MHz. The relationship between the number of SI antennas …

Image Dependent Relative Formation Navigation For Autonomous Aerial Refueling, James M. Howard

Theses and Dissertations

This research tests the feasibility, accuracy, and reliability of a predictive rendering and holistic comparison algorithm with use of an optical sensor to provide relative distance and position behind a lead or tanker aircraft. Using an accurate model of a tanker, an algorithm renders image(s) for comparison with actual collected images by a camera installed on the receiver aircraft. Based on this comparison, information used to create the rendered image(s) is used to provide the relative navigation solution required for autonomous air refueling. Given enough predicted images and processing time, this approach should reliably find an accurate solution. Building on …

Polarimetric Enhancements To Electro-Optical Aided Navigation Techniques, Jeremiah D. Johnson

Theses and Dissertations

Navigation in indoor and urban environments by small unmanned systems is a topic of interest for the Air Force. The Advanced Navigation Technology Center at the Air Force Institute of Technology is continually looking for novel approaches to navigation in GPS deprived environments. Inertial sensors have been coupled with image aided concepts, such as feature tracking, with good results. However, feature density in areas with large, flat, smooth surfaces tends to be low. Polarimetric sensors have been used for surface reconstruction, surface characterization and outdoor navigation. This thesis combines aspects of some of these algorithms along with a realistic, micro-facet …

Airborne Pseudolites In A Global Positioning System Degraded, Halit Oktay

Theses and Dissertations

The high accuracy of the Global Positioning System allows for precision navigation in support of current and future military operations. However, generating a three-dimensional position using GPS requires a clear line-of-sight between the user and at least four GPS satellites, and so the GPS service can be denied in scenarios such as a street surrounded by tall buildings. Therefore, there is a need for augmentation in these environments. Pseudolites, which transmit GPS-like ranging signals, can be deployed in order to improve the geometry and provide additional ranging signals. Users can then receive and process both GPS and pseudolite signals simultaneously …

Starting Cansat – Where To Now?, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint presentation created by Professor Bob Twiggs titled "Starting CanSat – Where to Now?" from March 8, 2011.

Test Case Series 1 (Overview Of Intercalibration Results: A Model Comparison), Thermal Performance Database Team

Ablation Workshop: Code Comparison

Presentation Overview:

• Comparison of model results
• All comparisons (plots) are percent difference from FIAT reference model

Overview Of Roughness And Blowing Effects In Flows Over Ablating Surfaces, Adam Amar, Charles Powars

Ablation Workshop

The scope of this session includes ablation effects on surface roughness and surface roughness effects on ablation. Ablation involves blowing, and so we address blowing including combined roughness and blowing effects. The two distinct types of ablating material surface roughness are defined with examples: 1) roughness related to the material inhomogeneity, and 2) roughness induced by turbulent flow that appears to be unrelated to material inhomogeneties.

Existing approaches for modeling ablative material surface roughness and blowing effects are overviewed. These range from empirical “augmentation factor” correlations to high-fidelity simulations of flow-surface interactions using modern CFD techniques. For models requiring input …

Gsi Modeling Overview: Requirements For Macroscopic Gas/Surface Interaction Coupling To Cfd Codes, Matthew Maclean, Jochen Marschall

Ablation Workshop

An overview is presented of a generalized finite-rate surface chemistry model that has been developed for gas/surface interaction coupling to the Data-Parallel Line-Relaxation (DPLR) code. Species from the gaseous environment are allowed to interact with species adsorbed onto one or more phase of a surface and with one or more phases of a bulk thermal protection system through an arbitrary number of finite-rate reactions. The reactions may include types such as adsorption, desorption, Eley-Rideal recombination, Langmuir-Hinschelwood recombination, partial or total dissociative adsorption, oxidation, reduction, sublimation, or condensation where forward and reverse rates are constrained by thermodynamics. A simple pyrolysis model …

High Enthalpy Ablation Testing At Dlr Cologne, Bunkard Esser, A. Gülhan, U. Koch

Ablation Workshop

Testing thermal protection capabilities of ablative materials is one of the main working areas of DLR’s arc heated facilities LBK in Cologne. Work on this particular topic has been intensified about five years ago with the following major focus points:

• Significant improvement of the facilities testing capabilities with respect to cold wall heat flux rates and stagnation pressure.
• Ablation testing in Martian atmosphere.
• Influence of dust particle erosion on ablation.

Nitric Oxide Plif Measurements In The Hypersonic Materials Environmental Test System (Hymets), Paul M. Danehy

Ablation Workshop

A nonintrusive laser-based measurement system has been applied for the first time in the HYMETS (Hypersonic Materials Environmental Test System) 400 kW arc-heated wind tunnel at NASA Langley Research Center. Planar laser-induced fluorescence of naturally occurring nitric oxide (NO) has been used to obtain instantaneous flow visualization images, and to make both radial and axial velocity measurements. Results are presented at selected facility run conditions, including some in simulated Earth atmosphere (75% nitrogen, 20% oxygen, 5% argon) and others in simulated Martian atmosphere (71% carbon dioxide, 24% nitrogen, 5% argon), for bulk enthalpies ranging from 6.5 MJ/kg to 18.4 MJ/kg. …

Experimental Data Need For High-Fidelity Material-Response Models, Jean R. Lachaud, Ioana Cozmuta, Nagi N. Mansour

Ablation Workshop

Several high-fidelity material-response models are being developed by the hypersonic community. These models require, in addition to the input parameters traditionally used in the state-of-the-art material-response codes, data not currently available - at least in the open literature. The presentations in the session will describe both state-of-the-art experimental techniques and innovative methods in support of model development and data acquisition for high-fidelity models.

Test Case Series 1, Jean R. Lachaud, Alexandre Martin, Ioana Cozmuta, Bernard Laub

Ablation Workshop: Code Comparison

A simple one-dimensional test case is defined for the purpose of inter-code comparison. This year the focus is set on in-depth physics and chemistry. Material properties, boundary conditions, and output format are provided.

An Investigative Study Of Gurney Flaps On A Naca 0036 Airfoil, Gregory F. Altmann

Master's Theses

This project examined the effect of Gurney flaps on a 2D, 2-ft chord NACA 0036 airfoil in the Cal Poly 3’x4’ low speed wind tunnel at 25 m/s.  It also covered the numerical simulation of the experiment in computational fluid dynamics (CFD).  During the study, problems with the wind tunnel data were seen.  After a careful diagnosis, the problem was traced to dirty flow conditioners which were subsequently replaced.

Five Gurney flaps at 1, 2, 3, 4, and 5% of the chord were tested.  The Gurney flaps had the effect of eliminating the lift reversal effect and lowering the profile …

Manufacturing And Evaluation Of A Biologically Inspired Engineered Mav Wing Compared To The Manduca Sexta Wing Under Simulated Flapping Conditions, Nathanial E. Deleon

Theses and Dissertations

In recent years, researchers have expressed a vested interest in the concepts surrounding flapping wing micro air vehicles (FWMAVs) that are capable of both range and complex maneuvering. Most research in this arena has found itself concentrated on topics such as flapping dynamics and the associated fluid-structure interactions inherent in the motion, however there still remains myriad questions concerning the structural qualities intrinsic to the wings themselves. Using nature as the template for design, FWMAV wings were constructed using carbon fiber and Kapton and tested under simplified flapping conditions by analyzing frozen' digital images of the deformed wing by methods …