Aerospace Engineering Commons^™

Space Program, Robert J. Twiggs

Robert "Bob" Twiggs STEM Education Collection

A PowerPoint Presentation created by Professor Bob Twiggs titled "Space Program" from June 12, 2025.

Evaluating The Physiological Effects Of A Spacesuit While Performing Cpr, Marielle Lenehan

Beyond: Undergraduate Research Journal

Limited research exists on the challenges of performing cardiopulmonary resuscitation (CPR) while wearing a spacesuit/pressure suit; but, during a space mission or following spacecraft egress, astronauts may need to perform Basic Life Support (BLS) on a crewmember. BLS consists of CPR and External Chest Compressions (ECC). In an emergency, astronauts may not have time to remove their intravehicular (IVA) spacesuits/pressure suits or wait for their heart rates to return to resting conditions and, therefore, would have to perform CPR while physically exerted. This study sought to evaluate the physiological exertion on rescuer performance while performing ECCs over 6 minutes while …

Investigation Of Stability And Control Shortcomings Of The North American X-15, William Lorenzo, Ramana Grandhi, Timothy T. Takahashi

Faculty Publications

There is growing interest in the design of maneuvering high-speed aircraft to fly within or at the edge of the atmosphere. We identify and develop novel quasi-static vehicle screening methodologies, suitable for use during preliminary design, to better predict an incipient loss of control due to the dynamic effects of feedback. We validate these metrics by reverse-engineering Neil Armstrong’s 1962 loss of control and inadvertent atmospheric skip while piloting the X-15. In 1962, then-extant flight dynamics screening methods did not forecast likely troubles. We assemble and refine a collection of predictive metrics which operate upon basic quasi-static aerodynamic data and …

Derivation And Experimental Validation Of A Parameterized Nonlinear Froude–Krylov Force Model For Heaving-Point-Absorber Wave Energy Converters, Houssein Yassin, Tania Demonte Gonzalez, Gordon Parker, Giorgio Bacelli, Carlos Michelen

Michigan Tech Publications

Wave energy converters (WECs) have gained significant attention as a promising renewable energy source. Optimal control strategies, crucial for maximizing energy extraction, have traditionally relied on linear models based on small motion assumptions. However, recent studies indicate that these models do not adequately capture the complex dynamics of WECs, especially when large motions are introduced to enhance power absorption. The nonlinear Froude–Krylov (FK) forces, particularly in heaving-point-absorbers with varying cross-sectional areas, are acknowledged as key contributors to this discrepancy. While high-fidelity computational models are accurate, they are impractical for real-time control applications due to their complexity. This paper presents a …

Computational And Experimental Study Of Slow Crack Growth In High Density Polyethylene, Abdulla Almomani

Thesis/ Dissertation Defenses

This dissertation investigates the slow crack growth (SCG) behavior of High-Density Polyethylene (HDPE) under various mechanical and environmental conditions. The study combines experimental analysis and computational modeling to enhance the understanding of SCG mechanisms in HDPE, particularly in pressurized pipes and under the exposure to hydrocarbons. A novel Crack Layer (CL) theory-based SCG model is developed and validated through experimental data, offering a predictive framework for HDPE failure assessment. The main objective of this dissertation is to quantify and model the viscoelastic-viscoplastic behavior of HDPE under monotonic and cyclic loading conditions while addressing SCG kinetics in structural applications. The study …

Gnss Technology, Utah State University Space Dynamics Laboratory

Space Dynamics Laboratory Publications

SDL presentation on GNSS Technology

Open-Source Cubesat Flight Software And Simulation, James Gruber

Computer Engineering

An open-source FreeRTOS-based flight software framework for CubeSats, with an example flight software package and simulation demonstrating real-time attitude control.

Cislunar Orbital Debris Removal Feasibility Analysis Using Nrho To Dro Transfers At Varying Solar Angles, Peter C. Lie

Master's Theses

The resurgence of lunar exploration necessitates the expansion of space situational awareness into cislunar space. The current tracking technologies for cislunar objects are insufficient to determine vacant orbital regimes for human spaceflight. Orbital debris generated in the cislunar environment often evolves along complex and chaotic trajectories due to the influence of multi-body dynamics. Current research into methods of removing orbital debris from space is limited to debris in Earth orbits. For cislunar orbits, debris disposal options are slowly gaining research, mostly centered on hypothetical solutions for active missions. Lunar impact and escape to heliocentric space are low-cost options, but serve …

Investigation Into Silicone-Silicate Conversion Due To Atomic Oxygen In The Low Earth Orbit Environment, Justin T. Self

Master's Theses

Silicones have been widely used over the years in spacecraft for a variety of functions, but atomic oxygen (AO) exposure in Low Earth Orbit causes a silicate (SiO₂) surface layer to rapidly develop on the silicone which results in a permanent change in its thermal and optical properties. Although this silicone to silicate conversion is known to occur, statistical predictions of layer formation as a function of time on orbit are not found in literature. This thesis utilized optical and scanning electron microscopy, Fourier-Transform Infrared Spectroscopy, diffuse reflectance spectroscopy, and nonlinear regression statistical techniques after RF plasma asher …

A Feasibility Study On Series Hybrid-Electric Propulsion For Narrow-Body Transport Aircraft, Carver J. Glomb

Master's Theses

As global climate change accelerates, the reduction of carbon emissions has become a critical objective across multiple industries. The aviation sector, however, has lagged behind other transportation domains in implementing sustainable alternatives, despite growing demand for air travel. Recent research and emerging technologies have proposed several decarbonization pathways, including hydrogen fuel, sustainable aviation fuels (SAFs), and hybrid or fully electric propulsion systems. Among these, series hybrid-electric propulsion has received comparatively limited attention, particularly for application in transport-class aircraft. This study investigates the feasibility and emissions-reduction potential of a series hybrid-electric propulsion architecture applied to a representative narrow-body platform. A Python-based …

Enhancement Of A Python Integral Boundary Layer Method, Jeffrey T. Azuma

Master's Theses

This thesis presents a series of additions to a Python based integral boundary layer software library known as PyBL. This library provides the user the means to calculate boundary layer properties using different models for boundary layer behavior. The additions feature the integration of a set of new laminar and turbulent integral boundary layer models originally developed for and currently found in the program XFOIL. These models were modified to fit the ODE solver method at the foundation of PyBL. A new method for PyBL that stitches a laminar and turbulent solution together has been developed to improve the ability …

Design And Development Of A Laboratory Star Tracker System, Kevin D. Iverson

Master's Theses

This thesis presents the design, calibration, and validation of a low-cost star tracker system and hardware-in-the-loop testbed intended for small satellite applications. The system is composed entirely of commercial off-the-shelf components and integrates both a custom star tracker and a screen-based star field simulator for controlled, repeatable testing. An analytical modeling approach was used in the early design phase to predict system accuracy based on key optical and geometric parameters, informing the selection and configuration of components and guiding the development of calibration routines.

A simulation environment was developed to validate the star tracker software and assess the impact of …

Thermally Perfect Augmentation Of A Supersonic Inlet Design Tool That Uses Method Of Characteristics, Mario V. Guardado

Master's Theses

This work is the first in a series to augment a supersonic air inlet design tool based in Python 3 to incorporate new models that increase the range of applicability of the tool. This effort focuses on improving the thermodynamics model by incorporating a thermally perfect gas model. This tool utilizes method of characteristics to solve the governing equations for an inviscid, irrotational, isentropic, steady, supersonic flow field. Multiple test cases are used to assess the accuracy of all new models. A comparison is made between the original code’s test case for a supersonic inlet at low temperatures to verify …

Development Of A Novel Bio-Mimetic Ornithopter With Variable Flapping Angle, Geourg Kivijian

Master's Theses

From the beginnings of flight, flapping-winged flight has been a goal of many engineers to mimic and replicate. With gains in aerodynamic efficiency of flight and certain other favorable characteristics such as reduced noise, higher maneuverability, and surveillance opportunities in urban environments, flapping-wing aerial vehicle(FWAV) designs are consistently pursued in many corners of academia and industry. This thesis goes into the development of a flapping wing aerial vehicle with a Bio-mimetic novel drive mechanism that is cable-driven and can produce variable amplitude and frequency flapping stroke. Employing a Field-Oriented Control (FOC) Brushless Direct Current (BLDC) motor, paired with a bio-mimetic …

Development Of A Reaction Wheel System For Cal Poly’S Spacecraft Attitude Dynamics Simulator, Caleb Nalley

Master's Theses

The Cal Poly Spacecraft Attitude Dynamics Simulator (SADS) is an ongoing project to develop a system capable of simulating the attitude dynamics and kinematics of a rigid body in space. Actuations on the SADS are performed by reaction wheels, however the current reaction wheels have various issues that decrease system performance and are not independent of the SADS. The reaction wheel developed as part of this thesis will be designed to improve performance and set out design specifications tailored to the SADS, serve as an independent assembly that can be transferred to other systems, and provide a general outline for …

In-Situ Defect Detection In Selective Laser Melting Using Convolutional Neural Networks, Ethan Gaigalas

Master's Theses

This thesis develops and trains a convolutional neural network (CNN) to classify defects in metal parts produced by selective laser melting (SLM) using acoustic emission (AE) data. The model successfully identified porosity and standard build layers with high accuracy but consistently struggled to classify lack of fusion (LOF) defects, regardless of input type, normalization, or class count. These results suggest that while AE signals contain distinguishable features for certain defect types, LOF signals may be too subtle or inconsistent for reliable detection. The study addresses the ongoing challenge of in-situ quality monitoring in metal additive manufacturing, where defects like cracks, …

Low Earth Orbit Drag Sail Degradation Due To Atomic Oxygen And Ultraviolet Radiation, Hannah Rost

Master's Theses

As the orbital debris population increases, so does the risk of collisions with operational spacecraft. In response, the Federal Communications Commission has shortened the deorbit requirement from 25 years to five years. While natural atmospheric decay was sufficient under the previous guideline, many objects with low area to mass ratios can no longer passively comply. Smaller, non-propellant-carrying space objects such as CubeSats lack the ability to maneuver and must rely on alternative deorbit methods. One proposed solution is to deploy a drag sail at end of life to increase atmospheric drag and accelerate orbital decay. However, exposure to atomic oxygen …

Analysis Of The Effects Of Extractor Orientation On The Performance Of An Electrospray System, Hannah Grace Sargent

Masters Theses

In this thesis, a single-emitter porous electrospray thruster was tested at nine different extractor electrode positions. The nine positions were: center, four slightly offset in each cardinal direction, and four significantly offset in each cardinal direction. Slightly offset was defined as ~25% of the distance from the center to the edge of the extractor orifice (~125 ± 2 μm) and significantly offset was defined as ~60% of the distance from the center to the edge of the extractor orifice (~302 ± 2 μm). Three diagnostic measurements were recorded to determine the effect of the extractor electrode position on thruster operation: …

Comparison Of Gravity Waves Observed By Atmospheric Waves Experiment (Awe) And Simulated By High-Resolution Waccm-X, Jiarong Zhang, Han-Li Liu, Yucheng Zhao, Dominique Pautet, Ludger Scherliess, Michael Taylor

Space Dynamics Laboratory Publications

Outline

Data: AWE and High-Resolution Whole Atmosphere Community Climate Model with thermosphere and ionosphere extension (HR-WACCMX) simulation

• Quantify gravity wave (GW) activity
• Compare GW activity observed by AWE and simulated by high-resolution WACCMX
• GW activity over Western Europe

Effect Of Thermal History On The Fracture And Fatigue Behaviors Of Semi-Crystalline Polymers Prepared Via Material Extrusion Additive Manufacturing, Ava M. Lea, Khaled Matalgah, Arief Yudhanto, Trevor J. Fleck

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Material extrusion (MEX) additive manufacturing (AM) is transforming the design and production of complex structures, providing reliable on-demand components. However, the effect of thermal history on the resultant microstructure and damage tolerance of MEX-AM materials is not fully understood. This research investigates the critical role of interfacial thermal history, which is dependent on processing conditions, in determining the fracture and fatigue behaviors of semi-crystalline polymers, as exemplified by polyamide-6 (PA-6). Utilizing infrared thermography, the thermal history, and its dependence on nozzle temperature of extruded PA-6, was investigated. Quasi-static and cyclic tests of compact tension specimens were used to evaluate fracture …

Leveraging Large Language Models (Llms) For Automated Generation Of Sysml V2 State Machines In Guidance, Navigation, And Control (Gnc) Systems, Andrea Louise Ames

Theses and Dissertations

Modern defense systems continue to grow in complexity, placing increasing pressure on engineering workflows to be faster and more adaptable. While Model-Based Systems Engineering (MBSE) with the emerging SysML v2 standard provides a framework for capturing system behavior, its practical use is often limited by the expertise and time required for manual modeling. This research investigates whether large language models (LLMs) can help overcome that barrier by automatically generating SysML v2 state machines from Guidance, Navigation, and Control (GNC) textual inputs. Three LLM Flowise-based models were developed and evaluated: the Structured Transformation Model (STM), which uses a structured extraction and …

Model-Based Design Of Compressed Lithium-Metal Pouch Cell Battery Modules For Evtol Applications, Scott J. Stirling

Master's Theses

Batteries with higher specific energy and power are essential for extending the range and performance of electric vertical takeoff and landing aircraft (eVTOLs). Anode-free lithium-metal pouch cells offer strong potential at the cell-level but require high compressive pressures to enhance cycle life and discharge performance. These pressures necessitate heavier structural components, reducing packaging efficiency at the module level.

To evaluate this tradeoff, a full-factorial enumeration model was developed to explore viable module designs within a constrained packaging volume. The model scales subsystem masses, enforces design rules and material limits, and accounts for large (~20%) cell thickness changes during cycling.

Results …

3d Printed Fixed Wing Aircraft Competition, Sidney E. Long, Mitchell Heise, Jack Bride, Daniel Salinas

Mechanical Engineering

Cal State LA and Arlington University, Texas are hosting the same 3D printed, fixed wing aircraft competition for 2025. Cal Poly requires a competitive plane that can adhere to each rule and be piloted remotely to achieve the longest time in the air. The plane must utilize solely 3D printing technology for the wings, body, and all other structures. The only off-the-shelf components can be the motor and electronics, as well as mechanical devices such as hinges.

Hardware-In-The-Loop Testing For The Polysim Adcs Lab, Shealyn P. Miller

Master's Theses

Hardware-in-the-loop, HIL, testing is an important tool for the validation and verification of systems in the aerospace industry. A common subsystem to be tested using HIL testing is the attitude, dynamics, and controls subsystem, ADCS. This is due to HIL tests using realistic simulations of the space environment to control physical hardware. To create a HIL test, a simulation and HIL interface are needed to test and communicate with hardware. Using a Speedgoat Performance Real-Time Target Machine to communicate with a Raspberry Pi and a Simulink model, three tests were conducted to ensure communication was functioning properly. A simulation, in …

Data Driven Analysis Of Samara Seed Kinematics And Dynamics, Shashwat Sparsh

Master's Theses

Samara Seeds are a class of fruit most famously belonging to the Acer species and are characterized by their single-bladed geometry and their auto-rotation response during descent. This steady-state auto-rotation response is the subject of aerodynamic analysis which aim to quantify the performance. The period prior to the beginning of steady-state auto-rotation is classified as the transition regime and has not been the subject of intense scrutiny.

This thesis employs a data-driven approach to analyzing the kinematic and dynamic response of these seeds during both the transition and auto-rotation stages of flight to quantify the performance with respect to the …

Development And Testing Of A Lab-Scale Resonance Igniter For Rocket Propulsion Applications, Aidan Caplan

Master's Theses

The resonance igniter is a type of rocket engine ignition system that initiates spontaneous combustion without using an external ignition source. This is possible because the activation energy needed for the combustion reaction to take place is provided by the igniter as it receives propellant flow. This can simplify the igniter hardware and lends it high re-usability while enabling the use of high-efficiency propellant combinations. Its potential benefits could make it a desirable alternative to traditional approaches such as using spark igniters or hypergolic propellants. The present research strove to inaugurate the study of the resonance igniter at Cal Poly …

Mae Enewsbrief Jan-Mar 2025, Department Of Mechanical And Aerospace Engineering, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Mae Enewsbrief Oct-Dec 2024, Department Of Mechanical And Aerospace Engineering, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Design And Development Of Hip Implants For Longevity Through Integrating Advanced Groove Structures And Additive Manufacturing, Asarudheen Abdudeen

Dissertations

This doctoral research concerns the design and optimization of hip implants (HIs) to enhance performance, durability, and improve patient outcomes by addressing the key issues of wear, deformation, and stress distribution. Innovative surface groove designs have been introduced to both a solid and a hollow femoral head with the aim of reducing friction and wear. The addition of grooves, with both a hemispherical and rectangular cross-section, onto the femoral head reduced friction, as debris produced by the inner liner was trapped within the grooves, significantly reducing adhesive wear. A numerical simulation study compared the effects of surface modifications both grooves …

An Inquiry Into The Physics Of Mixing And Floc Filtration, Andrew P. Pennock

Dissertations

Flocculation and clarification are two essential processes to deliver safe water at a reasonable cost to consumers. There are two major thrusts to the research presented in this dissertation. The first is to better characterize the physics and mixing parameters used for the design of hydraulic flocculators in the context of drinking water treatment plants. The second major thrust is to investigate floc filtration as a mechanism for the removal of primary particles during floc blanket clarification.

The intensity of mixing in environmental and chemical engineering applications is often characterized by the Camp and Stein velocity gradient. This parameter has …