Aerospace Engineering Commons^™

Molecular Simulation Of Steady-State Evaporation And Condensation: Validity Of The Schrage Relationships, Zhi Liang, Thierry Biben, Pawel Keblinski

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The Accuracy, or Even the Validity, of the Schrage Relationships Expressing the Rate of Evaporation and Condensation in Terms of Local Interfacial Thermodynamics Properties and the Mass Accommodation Coefficient is a Subject of Significant Discussion. in This Work, We Carry Out Molecular Dynamics (MD) Simulations of Evaporation and Condensation of Fluid Ar in a Nanochannel. by Adjusting the Temperature Difference, ΔT, between the Evaporating and Condensing Surfaces, We Control the Steady-State Evaporation and Condensation Fluxes (JMD). We Find that Across a Wide ΔT Range Studied, JMD is Always in Excellent Agreement with the Prediction from the Exact Schrage Relationships. Furthermore, …

Probabilistic Analysis And Verification Framework For Adaptive Flight Control, Mario Luca Fravolini, Tansel Yucelen, Marcello Napolitano

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A crucial aspect that could facilitate the applications of adaptive control systems in aerospace applications is the development of effective validation and verification procedures. Most of the existing analysis and design frameworks for adaptive controllers are based on the Lyapunov direct method. One well-known drawback of this approach is the conservatism in the estimation of the uniform ultimate boundedness region with little practical utility. To overcome this limitation, a probabilistic framework for the design of uniform ultimate boundedness regions is proposed where uncertain parameters and adaptive controls are considered as random variables. In this framework, the design is translated into …

Plume Characterization Of Electric Solid Propellant Pulsed Microthrusters, Matthew S. Glascock, Joshua L. Rovey, Shae Williams, Jason Thrasher

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Electric solid propellants are an attractive option for propulsion because they are ignited only by an applied electric current. This leads to capabilities such as on-demand throttling and reignition in chemical combustion operation, and it lends itself to application in electric propulsion. In this work, the plasma plume created by electric solid propellant pulsed micro thrusters is investigated using a nude Faraday probe, a triple Langmuir probe, and residual gas analysis. The thrusters are tested at a vacuum level of 2 x 10-5torr. Results indicate an average plume electron temperature of 1.7 eV and a density of 1011 to 1014cm-3. …

Long And Short-Range Air Navigation On Spherical Earth, Nihad E. Daidzic

International Journal of Aviation, Aeronautics, and Aerospace

Global range air navigation implies non-stop flight between any two airports on Earth. Such effort would require airplanes with the operational air range of at least 12,500 NM which is about 40-60% longer than anything existing in commercial air transport today. Air transportation economy requires flying shortest distance, which in the case of spherical Earth are Orthodrome arcs. Rhumb-line navigation has little practical use in long-range flights, but has been presented for historical reasons and for comparison. Database of about 50 major international airports from every corner of the world has been designed and used in testing and route validation. …

Summary Of "Supersonic Jet And Rocket Noise", Kent L. Gee, Caroline P. Lubert, Alan T. Wall, Seiji Tsutsumi

Department of Mathematics and Statistics - Faculty Scholarship

This paper summarizes a two-part special session, “Supersonic Jet and Rocket Noise,” which was held during the 174th Meeting of the Acoustical Society of America in New Orleans, Louisiana. The sessions were cosponsored by the Noise and Physical Acoustics Technical Committees and consisted of talks by government, academic, and industry researchers from institutions in the United States, Japan, France, and India. The sessions described analytical, computational, and experimental approaches to both fundamental and applied problems on model and full-scale jets and rocket exhaust plumes.

A Method For Evaluating Aircraft Electric Power System Sizing And Failure Resiliency, Cory Kenneth Kross

Master's Theses

With the More Electric Aircraft paradigm, commercial commuter aircraft are increasing the size and complexity of electrical power systems by increasing the number of electrical loads. With this increase in complexity comes a need to analyze electrical power systems using new tools. The Hybrid Power System Optimizer (HyPSO) developed by Airbus SAS is a simulator designed to analyze new aircraft power systems. This thesis project will first provide a method to assess the reliability of complex aircraft electrical power systems before and after failure and reconfiguration events. Next, an add-on to HyPSO is developed to integrate the previously developed reliability …

Influence Of Magnetic Nanoparticles And Magnetic Stress On An Ionic Liquid Electrospray Source, Kurt Joseph Terhune

Dissertations, Master's Theses and Master's Reports

Two electrospray sources were developed to operate on an ionic liquid ferrofluid; one source was a pressure‑fed capillary electrospray source and the other was a novel electrospray source which used a magnetically‑induced instability to produce a peak from which an electric field could extract electrospray. Multiple characteristics of electrospray operation were examined for both sources using faraday plates/cups, a quartz crystal microbalance, a retarding potential analyzer, and a time-of-flight mass spectrometer. The ILFF electrosprays for a capillary source were shown to operate in a mixed ion/droplet regime. The mass flow of the electrospray beam was primarily transported by larger particles …

Investigation Of Rope Formation In Gas–Solid Flows Through A 90° Pipe Bend Using High-Speed Video And Cfd Simulations, Sai S. Guda, Steven L. Rowan, Tao Yang

Faculty & Staff Scholarship

A study of rope formation in gas–solid flows through abrupt turns has been conducted. Experiments in which high-speed video was recorded and analyzed for solid concentration profiles were compared to CFD simulations utilizing both RANS and large eddy simulation turbulence models. In both simulations and experiments, particle-laden flows of air and ground flaxseed, with solid loadings of 35, 42, and 51% were considered. The results of the study demonstrate that both RANS and large eddy simulation can accurately predict particle roping. Furthermore, simulations show that the roping phenomenon is strongly dependent upon selection of an appropriate value for the coefficient …

Study Of Experimentally Blended Wings, Ray Roos 2894888

Williams Honors College, Honors Research Projects

This aim of this senior design project is to investigate the combination of a Selig 1223 and FX 74-CL5-140 into one profile to increase lift without significantly increasing drag. Our project began with researching current solutions for high lift and low drag airfoils. We found two airfoils which would be the target of our research, a Selig 1223 and the FX 74-CL5-140. After learning about the Cl and Cd of the current airfoils we built and physically tested the airfoils using additive manufacturing. A pressure differential tunnel was used to validate the airfoils. After researching how to blend two airfoil …

Design And Construction Of An Optimum Method To Present Uncertainty Of Convective Weather Forecasts To Air Traffic Personnel, Anna K. Selchow, Austin Wright

Williams Honors College, Honors Research Projects

The purpose of this design project was to develop a new weather display for air traffic controllers to utilize that shows the probabilistic hazard information for convective weather forecasts. Multiple iterations of maps were generated and evaluated for overall effectiveness in conveying uncertainty information for convective weather observations and forecasts with the final maps being tested through interviews with retired air traffic personnel. The goal of these maps was to improve upon current convective weather displays to more accurately show uncertainty and probabilistic hazard information to aid the air traffic controllers (ATCs) in providing guidance for aircraft pilots.

Indoor Mapping Drone, Benjamin J. Plevny, Andrew Armstrong, Miguel Lopez, Davidson Okpara

Williams Honors College, Honors Research Projects

This project addresses the need for an autonomous indoor mapping system that will create a 3D map of an unknown physical environment in real time. The aerial system moves and avoids obstacles autonomously, without the need for human remote control or observation. An aerial system produces a map of an unknown indoor environment by transmitting data received from the aerial device’s sensors. The transmission occurs over a wireless channel from the aerial device to a remote server for processing and storage of the data. As the transmission is done in real time, the aerial system does not require hardware for …

System Identification Of A Circulation Control Unmanned Aerial Vehicle, Mohammed Agha

Electronic Theses and Dissertations

The advancement in automation and sensory systems in recent years has led to an increase the demand of UAV missions. Due to this increase in demand, the research community has gained interest in investigating UAV performance enhancing systems. Circulation Control (CC), which is an active control flow method used to enhance UAV lift, is a performance enhancing system currently studied. In prior research, experimental studies have shown that Circulation Control wings (CCW) implemented on class-I UAVs can reduce take-off distance by 54%. Wind tunnel tests reveal that CC improves aircraft payload capabilities through lift enhancement. Increasing aircraft payload capabilities causes …

Rlc Circuit Simulated Response For Pulsed-Power Fusion Propulsion, Coleton Cody

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

Building Miniature-Sized Ion Thruster Using Split Ring Resonator (Srr), Toyofumi Yamaguchi

Summer Community of Scholars Posters (RCEU and HCR Combined Programs)

No abstract provided.

The Experimental Determination Of The Moment Of Inertia Of A Model Airplane, Michael Koken

Williams Honors College, Honors Research Projects

The objective of this project is to suggest that the moment of inertia for irregular shaped objects can easily be determined experimentally. The objects considered in this experiment were a solid wooden block and a model airplane. To ensure that the method and configuration is sufficient a wooden block with known moments of inertia was first tested, and the results from the experiment were compared to the known and accepted values. For this particular experiment, the periods were determined by timing how long 10 oscillations lasted for 10 different trials, and then taking the average of those 10 trials to …

Expedite Design Of Variable-Topology Broadband Hybrid Couplers For Size Reduction Using Surrogate-Based Optimization And Co-Simulation Coarse Models, Piotr Kurgan, Slawomir Koziel, Leifur Leifsson, Xiaosong Du

Mechanical and Aerospace Engineering Faculty Research & Creative Works

In this paper, we discuss a computationally efficient approach to expedite design optimization of broadband hybrid couplers occupying a minimized substrate area. Structure size reduction is achieved here by decomposing an original coupler circuit into low- and high-impedance components and replacing them with electrically equivalent slow-wave lines with reduced physical dimensions. The main challenge is reliable design of computationally demanding low-impedance slow-wave structures that feature a quasi-periodic circuit topology for wideband operation. Our goal is to determine an adequate number of recurrent unit elements as well as to adjust their designable parameters so that the coupler footprint area is minimal. …

Modeling Of Tow Wrinkling In Automated Fiber Placement Based On Geometrical Considerations, Roudy Wehbe

Theses and Dissertations

Automated manufacturing of fiber reinforced composite structures via numerically controlled hardware yields parts with increased accuracy and repeatability as compared to hand-layup parts. Automated fiber placement (AFP) is one such process in which structures or parts are built by adding bands of prescribed number of tows or slit-tape with prescribed width using robotic machine heads over 3D surfaces following prescribed paths. Despite the improved accuracy, different types of defects or manufacturing features arise during fabrication. These defects can be due to geometrical features, materials, and process planning parameters and are detected in the form of wrinkling, tow twist, tow folding, …

Wrinkling Of Functionally Graded Sandwich Structures Subject To Biaxial And In-Plane Shear Loads, Harold Costa

Masters Theses

"Benefits of a functionally graded core increasing wrinkling stability of sandwich panels have been demonstrated in a recent paper [1] where a several-fold increase in the wrinkling stress was observed, without a significant weight penalty, using a stiffer core adjacent to the facings. In the present paper wrinkling is analyzed in case where the facings are subject to biaxial compression and/or in-plane shear loading and the core is arbitrary graded through-the-thickness. Two issues addressed are the effect of biaxial or in-plane shear loads on wrinkling stability of panels with both graded and ungraded core and the verification that functional grading …

Theoretical Acoustic Absorber Design Approach For Lox/Lch4 Pintle Injector Rocket Engines, Jonathan Candelaria

Open Access Theses & Dissertations

Liquid rocket engines, or LREs, have served a key role in space exploration efforts. One current effort involves the utilization of liquid oxygen (LOX) and liquid methane (LCH4) LREs to explore Mars with in-situ resource utilization for propellant production. This on-site production of propellant will allow for greater payload allocation instead of fuel to travel to the Mars surface, and refueling of propellants to travel back to Earth. More useable mass yields a greater benefit to cost ratio. The University of Texas at El Paso's (UTEP) Center for Space Exploration and Technology Research Center (cSETR) aims to further advance these …

Development And Verification Of A Lab-Scale Green Propellant Hybrid Motor System, Shyamal Patel

Open Access Theses & Dissertations

Hybrid rocket propulsion offers the potential to combine advantages of both solid and liquid propellant systems, but low regression rates hinder their practicality. The suggested use of hydroxylammonium nitrate (HAN) based propellants in hybrids offers the potential for developing high impulse motors with low development and production costs. In this paper, I present the development of a small-scale system used to measure the regression rate of a hybrid motor. The system can accommodate fuel grains 5 cm long with an outer diameter of 6 cm and can implement the various decomposition gases needed for HAN. The motor firings of hydroxyl …

Design Of A 2000 Lbf Lox/Lch4 Throttleable Rocket Engine For A Vertical Lander, Israel Lopez

Open Access Theses & Dissertations

Liquid oxygen (LOX) and liquid methane (LCH4) has been recognized as an attractive rocket propellant combination because of its in-situ resource utilization (ISRU) capabilities, namely in Mars. ISRU would allow launch vehicles to carry greater payloads and promote missions to Mars. This has led to an increasing interest to develop spacecraft technologies that employ this propellant combination.

The UTEP Center for Space Exploration and Technology Research (cSETR) has focused part of its research efforts to developing LOX/LCH4 systems. One of those projects includes the development of a vertical takeoff and landing vehicle called JANUS. This vehicle will employ a LOX/LCH4 …

Design And Development Of A Delivery System For Green Ionic Monopropellants And Testing Of A 22n Thruster, Jaclyn Mona Mejia

Open Access Theses & Dissertations

LMP-103S and AFM-315E are emerging propellants that are less toxic to the environment than the propellants currently being used in spacecraft propulsion. Both propellants are a blend of liquid fuel, oxidizer and a majority percent of water. The diluted solutions enable the capability to handle and store the propellants with fewer requirements; for this reason, it decreases the overall cost of the propellants since it needs less precautions. The Missile Defense Agency (MDA) awarded the University of Texas at El Paso (UTEP) a contract to further research green propellants and eventually replace Hydrazide.

Development And Integration Of The Janus Robotic Lander: A Liquid Oxygen - Liquid Methane Propulsion System Testbed, Raul Ponce

Open Access Theses & Dissertations

Initiatives have emerged with the goal of sending humans to other places in our solar system. New technologies are being developed that will allow for more efficient space systems to transport future astronauts. One of those technologies is the implementation of propulsion systems that use liquid oxygen and liquid methane (LO2-LCH4) as propellants.

The benefits of a LO2-LCH4 propulsion system are plenty. One of the main advantages is the possibility of manufacturing the propellants at the destination body. A space vehicle which relies solely on liquid oxygen and liquid methane for its main propulsion and reaction control engines is necessary …

Quasi-Static Fracture Toughness Testing Of 7075 Aluminum For Spacecraft Separation Joint Applications, Ilse Alcantara

Open Access Theses & Dissertations

Separation joint systems are zero fault tolerant systems that have been used in complex aerospace applications such as vehicle stage separation and payload fairing removal. The structural members of separation joint systems must be able to withstand flight loads, but then completely fracture for instantaneous separation when an explosive is activated. The complex geometry and loading conditions of the structural member create a complicated stress state consisting of mixed tension and shear. A need exists to measure the fracture toughness of the material to ensure it will not support loads intended to fracture and measure its sensitivity to other variables, …

Lehmier Launch System, Dylan Lehmier 5248813

Williams Honors College, Honors Research Projects

The Lehmier Launch System was designed to propel a 120lb rocket 30,000 feet. Creating 2150 psi of thrust and 27,500 N-s of total impulse, it is the largest rocket motor ever used by the Akronauts Rocket Design Team.

Specialist Communities In China’S Aerospace Technology And Innovation System: The Cultural Dimension, Alanna Krolikowski

History and Political Science Faculty Research & Creative Works

Only two decades ago, China was a marginal player in the global aerospace industry. Today, the pace of China’s space programs is unparalleled and it has joined the sector’s leading ranks. China is the only country after the Soviet Union/Russia and the United States to independently send humans into orbit and a rover to touch down on the Moon. A Chinese station will likely soon be only the only long-term human habitat circling the Earth alongside the International Space Station. Within a decade, China could become only the second country in history to land a person on the Moon’s surface. …

Multi-Site Simultaneous Time-Resolved Photometry With A Low Cost Electro-Optics System, Forrest Gasdia, Aroh Barjatya, Sergei Bilardi

Publications

Sunlight reflected off of resident space objects can be used as an optical signal for astrometric orbit determination and for deducing geometric information about the object. With the increasing population of small satellites and debris in low Earth orbit, photometry is a powerful tool in operational support of space missions, whether for anomaly resolution or object identification. To accurately determine size, shape, spin rate, status of deployables, or attitude information of an unresolved resident space object, multi-hertz sample rate photometry is required to capture the relatively rapid changes in brightness that these objects can exhibit. OSCOM, which stands for Optical …

Cockpit In The Systems Engineering Lenses, Aysen K. Taylor, Charles B. Keating, T. Steven Cotter

Engineering Management & Systems Engineering Faculty Publications

The commercial transport aircraft of today vary greatly from early aircraft in regards to how they are controlled and the feedback provided from the machine to the human operator. Automation has improved operational precision and efficiency but at the cost of providing less feedback. Pilots are the last line of defense and current technology cannot provide the human ability to solve novel problems for which no computer logic can be written. The automated cockpits of today have may sub-components that interact in a manner often opaque and unpredictable when a sensor or sub-component fails or even in situations where no …

Intercomparison Of Modis And Viirs Fire Products In Khanty-Mansiysk Russia: Implications For Characterizing Gas Flaring From Space, Ambrish Sharma, Jun Wang, Elizabeth M. Lennartson

Department of Earth and Atmospheric Sciences: Faculty Publications

Gas flaring is commonly used by industrial plants for processing oil and natural gases in the atmosphere, and hence is an important anthropogenic source for various pollutants including CO₂, CO, and aerosols. This study evaluates the feasibility of using satellite data to characterize gas flaring from space by focusing on the Khanty-Mansiysk Autonomous Okrug in Russia, a region that is well known for its dominant gas flaring activities. Multiple satellite-based thermal anomaly data products at night are intercompared and analyzed, including MODIS (Moderate Resolution Imaging Spectroradiometer) Terra level 2 Thermal Anomalies product (MOD14), MODIS Aqua level 2 Thermal …

Robust Airfoil Design Optimization Using Stochastic Expansions And Utility Theory, Xiaosong Du, Leifur Leifsson, Slawomir Koziel

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Efficient and effective robust airfoil design optimization is proposed by integrating stochastic expansions and utility theory. In this work, the stochastic expansions are generated efficiently using non-intrusive polynomial chaos (NIPC) expansions. The robust design problem is formulated using utility functions which transfer a targeted response using a prescribed mathematical function to represent the designers' risk preferences. The proposed approach is demonstrated using examples of lift-constrained airfoil drag minimization in transonic viscous flow using the Mach number as an uncertain variable in the range of 0.70 to 0.75. The results are compared with the common problem formulation for robust design of …